This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the transmit path of firewire-net (IPv4 over 1394), the following
race condition may occur:
- The networking soft IRQ inserts a datagram into the 1394 async
request transmit DMA.
- The 1394 async transmit completion tasklet runs to finish cleaning
up (unlink datagram from list of pending ones, release skb and
outbound 1394 transaction object) --- before the networking soft IRQ
had a chance to proceed and add the datagram to the list of pending
datagrams.
This caused a panic in the 1394 async transmit completion tasklet when
it dereferenced unitialized list heads:
http://bugzilla.kernel.org/show_bug.cgi?id=15077
The fix is to add checks in the tx soft IRQ and in the tasklet to
determine which of these two is the last referrer to the transaction
object. Then handle the cleanup of the object by the last referrer
rather than assuming that the tasklet is always the last one.
There is another similar race: Between said tasklet and fwnet_close,
i.e. at ifdown. However, that race is much less likely to occur in
practice and shall be fixed in a separate update.
Reported-by: Илья Басин <basinilya@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Calling ath_bus_cleanup() after ieee80211_free_hw() resulted in access
to common->bus_ops, which is already freed as part of the device data.
Remove the cleanup field in struct ath_bus_ops, as it was never used
properly. Remove ath_bus_cleanup(). Merge cleanup functions in place
of the ath_bus_cleanup() calls. Take care not to use any device data
after ieee80211_free_hw().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using stack for that causes warnings with CONFIG_FRAME_WARN=1024
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous changeset left behind an unused inode variable.
This patch removes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add an extra debugging check function which validates writes.
After every write it reads the data back, compares it with the
original data, and complains if they mismatch.
Useful for debugging. No-op if extra debugging checks are disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI debugging functions were a little bit over-engineered and
returned more error codes than needed, and the callers had to
do useless checks. Simplify the return codes.
Impact: only debugging code is affected, which means that for
non-developers this is a no-op patch.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In the error path of 'ubi_attach_mtd_dev()' we have a tricky situation:
we have to release things differently depending on at which point
the failure happening. Namely, if @ubi->dev is not initialized, we have
to free everything ourselves. But if it was, we should not free the @ubi
object, because it will be freed in the 'dev_release()' function. And
we did not get this situation right.
This patch introduces additional argument to the 'uif_init()' function.
On exit, this argument indicates whether the final 'free(ubi)' will
happen in 'dev_release()' or not. So the caller always knows how to
properly release the resources.
Impact: all memory is now correctly released when UBI fails to attach
an MTD device.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds a capability to attach MTD devices by their character
device paths. For example, one can do:
$ modprobe ubi mtd=/dev/mtd0
to attach /dev/mtd0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @mtd_devs and @mtd_dev_param variables are used only during the
initialization, and all functions that use the variables have
the __init prefix. This means we can safely mark the variables
as __initdata, which is a tiny optimization.
Impact: tiny RAM consumption optimization when UBI is used as a kernel
module.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME and xircom_cb from pr_<level>
Convert embedded function names in logging messages to %s, __func__
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Convert %d.%d.%d.%d to %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from logging messages
Add do {} while(0) to ULI526X_DBUG macro
Make SHOW_MEDIA_TYPE macro more readable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove 'DRV_NAME ": ' from logging messages
Convert commented out printks to pr_debug
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to dev_<level> where appropriate
Convert printks to pr_<level>
Change print formats with %d.dx to %0dx
Coalesce long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If acpi_bus_add does not return a device and it's passed
to acpi_bus_start, bad things will happen:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8128402d>] acpi_bus_start+0x14/0x24
...
[<ffffffffa008977a>] acpiphp_bus_add+0xba/0x130 [acpiphp]
[<ffffffffa008aa72>] enable_device+0x132/0x2ff [acpiphp]
[<ffffffffa0089b68>] acpiphp_enable_slot+0xb8/0x130 [acpiphp]
[<ffffffffa0089df7>] handle_hotplug_event_func+0x87/0x190 [acpiphp]
Next patch would make this NULL pointer check obsolete, but
better having one more than one missing...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
The IMX family of Application Processors is shipped with a Keypad Port
supported by this driver.
The peripheral can control up to an 8x8 matrix key pad where all the
scanning is done via software. The hardware provides two interrupts:
one for key presses (KDI) and one for all key releases (KRI). There is
also a simple circuit for glitch reduction (said for synchronization)
made by two series of 3 D-latches clocked by the keypad-clock that
stabilize the interrupts sources. KDI and KRI are fired only if the
respective conditions are maintained for at last 4 keypad-clock cycle.
Since those circuits are poor for a correct debounce process (the
keypad-clock frequency is 32K and bounces longer than 94us are not
masked) the driver, when an interrupt arrives, samples the matrix
with a period of 10ms until the readins are stable for
IMX_KEYPAD_SCANS_FOR_STABILITY times (currently set at 3). After
getting stable result appropriate events are sent through the input
stack.
If some keys are maintained pressed, the driver continues to scan
the matrix with a longer period (60ms) to catch possible multiple
key presses without overloading the cpu. This process ends when all
keys are released.
This driver is tested to build in kernel or as a module and follow
the specification of Freescale Application processors:
i.MX25 i.MX27 i.MX31 i.MX35 i.MX51 especially tested on i.MX31.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>