When DSS transitions from off mode to on VENC may generate a spurious
SYNC_LOST_DIGIT error. Just ack it when restoring the context. Also
restore IRQENABLE last to avoid triggering interrupts before the
context is fully restored.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When the display is not active make the wait_for_go() functions return
immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check whether the display actually has the set_update_mode() function
before calling it. Only the sysfs codepath was broken, the omapfb ioctl
had the necessary protection.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
For some reason screen updates of certain odd widths seem to be triggering
HS TX timeouts on OMAP 3430, even if bigger updates do not. The reason for
this is unknown, but increasing the timeout removes the problem with no
(so far) noticeable problems. I haven't seen this problem on OMAP 3630.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Several drivers contained dummy code to request for memory windows,
even though they never made use of it. Remove all such code
snippets.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Insert PCMCIA device resources into the resource tree. However, this is
currently only implemented for sockets which do not statically map the
resources.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Introduce a new field into struct pcmcia_device named "resource" and of
type struct resource *, which contains the IO port ranges allocated for
this device. Memory window ranges and registration with the resource
trees will follow at a later date.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch adds support for RGMII RX/TX delay configuration on marvell 88e1121
and derivatives. With this patch, PHY_INTERFACE_MODE_RGMII_*ID modes are now
supported on these devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo was causing compilation errors since "dev" was not defined.
Signed-off-by: Henrique Camargo <henrique.camargo@ensitec.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize all IRQs when using MSI-X. Similar to ixgbe.
Issue was reported on e1000e, but the patch is also valid for igb.
CC: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue that resulted in a null pointer dereference
for the addition of VLAN 0 without any VLANs being registered. Also this
code removes some unnecessary checks for defines and the unnecessary setting
of VLAN flags since that is now handled within the kernel via the
vlan_features.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch/work from Jean Delvare <jdelvare@suse.de>
Synchronize all IRQs when in MSI-X IRQ mode.
Jean's original patch hard coded the sync with the 3 possible vectors,
this patch incorporates more flexibility for the future and aligns
with how igb stores the number of vectors into the adapter structure.
CC: Jean Delvare <jdelvare@suse.de>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_qos_add_request call has to register the pm_qos request with the pm_qos
susbsystem before first use of the pm_qos request via
pm_qos_update_request.
As pm_qos changed to use plists there is no benefit in registering and
unregistering the pm_qos request on ifup/ifdown and thus we move the
registering into e1000_open and the unregistering in e1000_close.
This fixes the following warning:
[ 1.786060] WARNING: at kernel/pm_qos_params.c:264
pm_qos_update_request+0x28/0x54()
[ 1.786088] Hardware name: Latitude E6500
[ 1.787045] pm_qos_update_request() called for unknown object
[ 1.787966] Modules linked in:
[ 1.788940] Pid: 1, comm: swapper Not tainted 2.6.35-rc5-mmotm0719 #1
[ 1.790035] Call Trace:
[ 1.791121] [<ffffffff81037335>] warn_slowpath_common+0x80/0x98
[ 1.792205] [<ffffffff810373e1>] warn_slowpath_fmt+0x41/0x43
[ 1.793279] [<ffffffff81057c14>] pm_qos_update_request+0x28/0x54
[ 1.794347] [<ffffffff8134889e>] e1000_configure+0x421/0x459
[ 1.795393] [<ffffffff8134afbd>] e1000_open+0xbd/0x37c
[ 1.796436] [<ffffffff8105743a>] ? raw_notifier_call_chain+0xf/0x11
[ 1.797491] [<ffffffff8145f948>] __dev_open+0xae/0xe2
[ 1.798547] [<ffffffff8145f997>] dev_open+0x1b/0x49
[ 1.799612] [<ffffffff8146e36e>] netpoll_setup+0x84/0x259
[ 1.800685] [<ffffffff81b5037c>] init_netconsole+0xbc/0x21f
[ 1.801744] [<ffffffff81b5026c>] ? sir_wq_init+0x0/0x35
[ 1.802793] [<ffffffff81b502c0>] ? init_netconsole+0x0/0x21f
[ 1.803845] [<ffffffff810002ff>] do_one_initcall+0x7a/0x12f
[ 1.804885] [<ffffffff81b2ccae>] kernel_init+0x138/0x1c2
[ 1.805915] [<ffffffff81003554>] kernel_thread_helper+0x4/0x10
[ 1.806937] [<ffffffff81590e00>] ? restore_args+0x0/0x30
[ 1.807955] [<ffffffff81b2cb76>] ? kernel_init+0x0/0x1c2
[ 1.808958] [<ffffffff81003550>] ? kernel_thread_helper+0x0/0x10
[ 1.809958] ---[ end trace 84b562a00a60539e ]---
Signed-off-by: Florian Mickler <florian@mickler.org>
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endpoint timer manipulation needs to be done inside the lock. Otherwise
we can get into a situation where a timer is stopped before it is started,
which hits the WARN_ON() in stop_ep_timer().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is only one control txq per tx channel. So use the port number
as the queue index when sending.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There exists a race condition where the app disconnects, which
initiates an orderly close (via rdma_fini()), concurrently with an
ingress abort condition, which initiates an abortive close operation.
Since rdma_fini() must be called without IRQs disabled, the fini can
be called after the QP has been transitioned to ERROR. This is ok,
but we need to protect against qp->ep getting NULLed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Split ioctl handling into 3 separate sections: fixed-length ioctls,
variable-length ioctls and multi-number variable length handlers.
This reduces identation and makes the code a bit clearer.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As all callers are now changed to only use the input_abs_*() access
helpers, switching over to dynamically allocated ABS information is
easy. This reduces size of struct input_dev from 3152 to 1640 on
64 bit architectures.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change all call sites in drivers/input to not access the ABS axis
information directly anymore. Make them use the access helpers instead.
Also use input_set_abs_params() when possible.
Did some code refactoring as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The kpad structure is assigned to i2c client via i2s_set_clientdata()
at the end of adp5588_probe(), but in adp5588_gpio_add() we tried to
access it (via dev_get_drvdata! which is not nice at all) causing an
oops.
Let's pass pointer to kpad directly into adp5588_gpio_add() and
adp5588_gpio_remove() to avoid accessing driver data before it is
set up.
Also split out building of gpiomap into a separate function to
clear the logic.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Removed TODO item 2 :
Current UIM/KIM communicate via the rfkill device and identified by the unique idx
assisgned by the rfkill sub-system to each of these rfkill entries.
Removed TODO item 1 :
Since there is no way we can test existance of multiple connectivity
devices on platform.
However the basic infrastructure as in providing a context to ST driver
exist.
If multiple devices have to exist on a given platform, multiple ST
platform devices need to be registered and each of the protocol drivers
have to mention which platform device they want to bind to/make use of.
Removed TODO item 3:
Locking have been reviewed and commit
36b5aee46b documents locking.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a common name format for PCI_VENDOR/DEVICE_ID constants.
wlags49_h2 names doesn't fit in the standard.
This patch change the names and also fix some style issues.
Thanks a lot,
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the wwrap.c file that fixes up a brace warnings and
other errors found by the checkpatch.pl tool.
Signed-off-by: Daniele Boncompagni <daniele.boncompagni@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compilation warning:
drivers/staging/quatech_usb2/quatech_usb2.c:1852: warning:
‘qt2_box_flush’ defined but not used
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rtl8192_usb_probe() does not check alloc_ieee80211() and
register_netdev() return values for errors.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kmalloc() may fail, if so return error from zfwUsbSubmitControl().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
request_irq() may fail, if so propagate error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix errors and warnings reported by checkpatch
in p80211meta.h and p80211metstruct.h.
Signed-off-by: Edgardo Hames <ehames@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patches removes the only typedef in p80211ioctl.h
Signed-off-by: Edgardo Hames <ehames@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replaced NTSTATUS with int, as defined in a couple of places.
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By definition the broadcast address is also a multicast address.
Lindented the modified section as required by checkpatch.pl.
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
