Fix possible double priv->mutex lock introduced by commit
a69b03e941
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.
We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
The Ux500 variant has a 24-bit MMCIDATALENGTH register, as opposed to
the 16-bit one on the ARM version.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although both the U300 and Ux500 use ST variants, the HWFCEN bits are at
different positions, so use the variant_data to store the information.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a variant_data structure to handle the differences between the
various variants of this peripheral. Add a first quirk for a default
MCICLOCK value, required on the Ux500 variant where the enable bit needs
to be always set, since it controls access to some registers.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platforms may have some external power control which need to be
controlled from board specific code. Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In general the semantics of IPIs are that they are are expected to
continue functioning after dpm_suspend_noirq().
Specifically I have seen a deadlock between the callfunc IPI and the
stop machine used by xen's do_suspend() routine. If one CPU has already
called dpm_suspend_noirq() then there is a window where it can be sent
a callfunc IPI before all the other CPUs have entered stop_cpu().
If this happens then the first CPU ends up spinning in stop_cpu()
waiting for the other to rendezvous in state STOPMACHINE_PREPARE while
the other is spinning in csd_lock_wait().
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: xen-devel@lists.xensource.com
LKML-Reference: <1280398595-29708-4-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kw_i2c_irq and via_pmu_interrupt are not timer interrupts and
therefore should not use IRQF_TIMER. Use the recently introduced
IRQF_NO_SUSPEND instead since that is the actual desired behaviour.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linuxppc-dev@ozlabs.org
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1280398595-29708-3-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ixp4xx_spkr_interrupt is not a timer interrupt and therefore should
not use IRQF_TIMER. Use the recently introduced IRQF_NO_SUSPEND
instead since that is the actual desired behaviour.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
LKML-Reference: <1280398595-29708-2-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We're adjusting horizontal timings only here, moving vsync was just a
slavish translation of a typo in the X server.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
[SCSI] zfcp: Update status read mempool
[SCSI] zfcp: Do not wait for SBALs on stopped queue
[SCSI] zfcp: Fix check whether unchained ct_els is possible
[SCSI] ipr: fix resource path display and formatting
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
NULL pointer dereferences in ib_cm_init_qp_attr() were seen by some
users. From a crash dump, I determined that we died in
cm_init_qp_rts_attr() (it's inlined, so it doesn't show up in the
traceback) on the line labeled below:
static int cm_init_qp_rts_attr(struct cm_id_private *cm_id_priv,
struct ib_qp_attr *qp_attr,
int *qp_attr_mask)
{
........
if (cm_id_priv->id.lap_state == IB_CM_LAP_UNINIT) {
.....
} else {
*qp_attr_mask = IB_QP_ALT_PATH | IB_QP_PATH_MIG_STATE;
qp_attr->alt_port_num = cm_id_priv->alt_av.port->port_num; <-die
The problem is that the rdma_cm can call ib_send_cm_mra() after a
connection has been established. The ib_cm incorrectly assumes that
the MRA is in response to a LAP (load alternate path) message, even
though no LAP message has been received. The ib_cm needs to check the
lap_state before sending an MRA if the cm_id state is established.
Reported-by: Arthur Kepner <akepner@sgi.com>
Reported-by: Josh England <jjengla@gmail.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When ib_unregister_device() is called from netdev stop during ifdown,
it sometimes hangs. Changes made to indicate port_err to ib_dispatch_event()
during netdev stop and port_active during netdev open. The
ib_unregister_device() is only called during remove of the module.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Read and print eeprom version and save it off for later use.
Also delete a tab.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove find_gcf from nldr.c and use kernel function
gcd().
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove bridge_brd_delete() function since it is
doing the same that bridge_brd_stop().
Signed-off-by: Ernesto Ramos <ernesto@ernesto-desktop.(none)>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regardless the IVA2 power state before bridgedriver is
installed, the driver must ensure that IVA2 power
state is OFF when the device driver is created.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a base image is being loaded or started and by some reason
the process fails, the IVA2 should be switched OFF.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
right now, bridge_brd_stop is not changing the IVA2 power state
to OFF since PM_PWSTST_IVA2 is not 0 after calling this function.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_FAILED
is not necessary anymore. This patch removes this
define.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore. This patch removes this
define.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove function delete_strm_mgr in strm.c and
use kfree instead.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
update TODO to reflect the items taken care of,
update ABI to reflect the new debugfs entries exposed.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
