Commit graph

94,495 commits

Author SHA1 Message Date
NeilBrown
415e72d034 md/raid5: Allow recovered part of partially recovered devices to be in-sync
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.

This is particularly important for a reshape which suffers device
failure.  Treating the data as in-sync can mean the difference between
data-safety and data-loss.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:39 +10:00
NeilBrown
674806d62f md/raid5: More careful check for "has array failed".
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.

In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.

So encode this subtlety in a new function and call it as appropriate.

The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:

  good good good good incomplete good good failed failed

while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.

Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:27 +10:00
NeilBrown
70fffd0bfa md: Don't update ->recovery_offset when reshaping an array to fewer devices.
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.

If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.

Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.

This becomes relevant in the following sample scenario:

A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses.  The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.

If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:18 +10:00
NeilBrown
e4e11e385d md/raid5: avoid oops when number of devices is reduced then increased.
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant.  Otherwise if we enlarge the array again,
we will reference uninitialised values.

As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:02 +10:00
Maciej Trela
049d6c1ef9 md: enable raid4->raid0 takeover
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:34:57 +10:00
Maciej Trela
001048a318 md: clear layout after ->raid0 takeover
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:34:45 +10:00
Maciej Trela
f73ea87375 md: fix raid10 takeover: use new_layout for setup_conf
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover().  That
gets set in run()

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:33:51 +10:00
NeilBrown
e93f68a1fc md: fix handling of array level takeover that re-arranges devices.
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).

This renumbering is currently being done in the ->run method when the
new personality takes over.  However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.

Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.

So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.

Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:33:24 +10:00
Prasanna S. Panchamukhi
0544a21db0 md: raid10: Fix null pointer dereference in fix_read_error()
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().

Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:31:03 +10:00
NeilBrown
f3b99be19d Restore partition detection of newly created md arrays.
Commit  b821eaa572 broke partition
detection for md arrays.

The logic was almost right.  However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.

So when md_open is called we still need to ensure that
->bd_invalidated gets set.  This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change.  At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.

Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:31:03 +10:00
David S. Miller
8244132ea8 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/ipv4/ip_output.c
2010-06-23 18:26:27 -07:00
Ohad Ben-Cohen
7454c8f6b8 staging: ti dspbridge: add TODO file
Add a general cleaning roadmap TODO file to TI's DSP Bridge
staging driver.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:08 -07:00
Omar Ramirez Luna
6280238c13 staging: ti dspbridge: add header files
Add TI's DSP Bridge driver header files

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:08 -07:00
Omar Ramirez Luna
26f8db7d2e staging: ti dspbridge: add DOFF binaries loader
Add TI's DSP Bridge DOFF binaries dynamic loader driver sources

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:08 -07:00
Omar Ramirez Luna
6a88a4fe09 staging: ti dspbridge: add services
Add TI's DSP Bridge driver services code

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:07 -07:00
Omar Ramirez Luna
7227b671f7 staging: ti dspbridge: add generic utilities
Add TI's DSP Bridge generic utilities driver sources

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:07 -07:00
Omar Ramirez Luna
5cc28e622f staging: ti dspbridge: add MMU support
Add TI's DSP Bridge MMU support

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:07 -07:00
Omar Ramirez Luna
7d55524d30 staging: ti dspbridge: add resource manager
Add TI's DSP Bridge resource manager driver sources

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:07 -07:00
Omar Ramirez Luna
c4ca3d5a4b staging: ti dspbridge: add platform manager code
Add TI's DSP Bridge platform manager driver sources

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:07 -07:00
Omar Ramirez Luna
999e07d632 staging: ti dspbridge: add core driver sources
Add TI's DSP Bridge core driver sources

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:06 -07:00
Omar Ramirez Luna
6c5fe83876 staging: ti dspbridge: add driver documentation
Add a README with a general overview of TI's DSP Bridge driver,
a short explanations of how error codes are currently used,
and a CONTRIBUTORS file with all past & present contributors.

For additional information about TI's DSP Bridge,
check out http://omapzoom.org/gf/project/omapbridge/docman/?subdir=3

Note: if by any chance we forgot to mention any contributor,
please let us know and we will fix that.

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Kanigeri, Hari <h-kanigeri2@ti.com>
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Guzman Lugo, Fernando <fernando.lugo@ti.com>
Signed-off-by: Hebbar, Shivananda <x0hebbar@ti.com>
Signed-off-by: Ramos Falcon, Ernesto <ernesto@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anna, Suman <s-anna@ti.com>
Signed-off-by: Gupta, Ramesh <grgupta@ti.com>
Signed-off-by: Gomez Castellanos, Ivan <ivan.gomez@ti.com>
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Armando Uribe De Leon <x0095078@ti.com>
Signed-off-by: Deepak Chitriki <deepak.chitriki@ti.com>
Signed-off-by: Menon, Nishanth <nm@ti.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:39:06 -07:00
Andrea Gelmini
6c2bfdc77f Staging: ti-st: Fix a typo in the Kconfig file
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:26:28 -07:00
Prashant P. Shah
194a636d7a Staging: wl_cs.c: fixed style issues in wl_cs.c
This is a patch to the wl_cs.c file that fixes braces, spaces
parentheses, etc style issues found by the checkpatch.pl tool.

Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:25:19 -07:00
Prashant P. Shah
8cd5778b77 Staging: wl_cs.c: fixed invalid UTF-8 style issues in wl_cs.c
This is a patch to the wl_cs.c file that corrects the invalid
UTF-8 encoding style issues found by the checkpatch.pl tool.

Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:25:18 -07:00
Prashant P. Shah
6d98be390a Staging: wl_cs.c: converted space to tabs in wl_cs.c
This is a patch to the wl_cs.c file that converts spaces to
tabs style issues found by the checkpatch.pl tool.

Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:25:16 -07:00
H Hartley Sweeten
55bb6ece16 Staging: dt3155: Cleanup memory mapped i/o access
The macros ReadMReg and WriteMReg are really just private versions of
the kernel's readl and writel functions.  Use the kernel's functions
instead.  And since ioremap returns a (void __iomem *) not a (u8 *),
change all the uses of dt3155_lbase to reflect this.

While here, make dt3155_lbase static since it is only used in the
dt3155_drv.c file.  Also, remove the global variable dt3155_bbase
since it is not used anywhere in the code.

Where is makes sense, create a local 'mmio' variable instead of using
dt3155_lbase[minor] to make the code more readable.

This change also affects the {Read|Write}I2C functions so they are
also modified as needed.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Scott Smedley <ss@aao.gov.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:22:36 -07:00
Andres More
4b50fb4042 Staging: vt6656: replaced IS_BROADCAST_ADDRESS with is_broadcast_ether_addr
Replaced and removed the custom definition.
Minor checkpatch warnings on long lines and indentation were not cleared.

Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:20:21 -07:00
Andres More
6cda24f5df Staging: vt6656: code cleanup of vt6656_disconnect()
Fixed style and debugging printks.
Not replaced PSDevice here, nor removed wireless_send_event() yet.

Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:20:21 -07:00
Ben Collins
054fa2267d Staging: solo6x10: Add TODO
Signed-off-by: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:20:20 -07:00
Ben Collins
ee6351f56a Staging: solo6x10: Support for tw2865 in cascade/full modes
Finally got ahold of a card with a tw2865 video/audio multiplexer and
the spec sheet to go along with it.

Signed-off-by: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-23 15:20:20 -07:00
Daniel Walker
08ecfde475 mmc: msm: fix up build breakage on !PM
with PM disabled I get the following compile error,

drivers/built-in.o: In function `msmsdcc_resume':
linux-2.6/drivers/mmc/host/msm_sdcc.c:1352: undefined reference to `mmc_resume_host'
drivers/built-in.o: In function `msmsdcc_suspend':
linux-2.6/drivers/mmc/host/msm_sdcc.c:1330: undefined reference to `mmc_suspend_host'

This adds ifdefs around the suspend/resume functions to prevent this.

Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
2010-06-23 15:11:34 -07:00
Brandon Philips
38000a94a9 sky2: enable rx/tx in sky2_phy_reinit()
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.

However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:

$ ethtool -r eth0
$ ethtool -A eth0 autoneg off

Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.

Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 14:37:04 -07:00
Ursula Braun
01fc3e86c6 qeth: handle missing z/VM authorization of OSX
For z/VM guest operating systems, OSX CHPIDs can only be used, if
LPAR and z/VM userID are explicitly authorized through the Service
Element. Issue a message if this SE-authorization is missing.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:37 -07:00
Ursula Braun
0132951e81 qeth: specify correct function level for OSN devices
OSN devices use the same function level as OSD devices. This patch
adds OSN-devices to the initialization function for func_level.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:37 -07:00
Frank Blaschka
51aa165c9f qeth: fix page breaks in hw headers
Turning on memory debugging showed there could be page breaks in
hardware headers. OSA does not allow this so we had to add code
to bounce the header in case there is a page break. This patch also
fixes a problem in case the skb->data part of a fragmented skb
spreads multiple pages.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:36 -07:00
Carsten Otte
43a65303fe qeth: fix use after free for qeths debug area
The function qeth_free_buffer_pool is called _after_ the per-card
debug area has been released. This debug message is not all that
usefull anyway, and thus gets removed.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:36 -07:00
Carsten Otte
38593d019d qeth: Fold qeth_qerr debug area
This patch removes the qerr debug area. Most info that goes in here is logged
to the card's local debug area already, those duplicates are removed. All other
elements are moved to the card's local debug area.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:35 -07:00
Carsten Otte
efd5d9a407 qeth: Fold qeth_misc debug area
This patch removes the misc debug area. Instead of logging the entire skb
we just log a pointer to it into the card's local debug area in
qeth_core_get_next_skb. Other then that, this debug area is not used anywhere.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:35 -07:00
Carsten Otte
d829eeef58 qeth: Fold qeth_sense debug area
This patch removes the sense debug area completely. Despite the name this
debug area makes no sense at all because it's unused completely. Ouch.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:34 -07:00
Carsten Otte
847a50fd9f qeth: Fold qeth_trace debug area
This patch removes the qeth_trace debug area. All relevant data is logged into
either qeth_setup or into each card's own debug area. Superfluous information
(such as the card number when logging into the card's own debug area) is
removed without replacement.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:34 -07:00
Carsten Otte
af039068ca qeth: Add new s390 debug feature for each qeth card
This patch adds a debug area for each qeth card. This debug area will replace
various other debug areas that are global for all cards handled by the device
driver. On crash dump analysis this makes life easier when trying to find out
what's going on with an interface. Also, the forest of debug areas for this
device driver is significantly cleared up.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:33 -07:00
Carsten Otte
8e96c51cb6 qeth: Rework qeth_dbf_longtext
This patch decouples qeth_dbf_longtext from qeth's static debug array. The
function only uses one member anyway.

Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:33 -07:00
Ursula Braun
59b60e9724 smsgiucv: guarantee single iucv connect in thaw
If another smsgiucv_app device exists, suspend / resume fails with
iucv path list corruption, because the same iucv_path_connect is
called twice.
The patch introduces a flag to save connect status of the smsgiucv
path to make sure iucv_path_connect in smsg_pm_restore_thaw is
called only once.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:32 -07:00
Amit Kumar Salecha
4eaef482df qlcnic: update version to 5.0.6
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:32 -07:00
Amit Kumar Salecha
d626ad4d84 qlcnic: mark context state freed after destroy
After destroying recv ctx, context state remain same.
Fix it by marking as FREED.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:31 -07:00
Amit Kumar Salecha
68bf1c68a4 qlcnic: offload tx timeout recovery
Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:31 -07:00
Amit Kumar Salecha
52486a3ac8 qlcnic: dont free host resources during fw recovery
There is no need to free/alloc host resources during firmware
recovery.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:30 -07:00
Amit Kumar Salecha
8a15ad1fb1 qlcnic: release device resources during interface down
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:30 -07:00
Amit Kumar Salecha
42f65cbad4 qlcnic: fix mac address mgmt
We first add mac address in driver local list and then send command to
fw to add same. There are checks in driver to ensure send command doesn't fail
before adding mac address in local list.

But instead fix should be:
Add mac address in fw and if it succeeds, add it in driver local list.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:29 -07:00
Amit Kumar Salecha
900c6cfffa qlcnic: handshake with card after fw load
Instead of delaying rcv handshake till interface comes up,
do it just after fw load.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23 13:16:29 -07:00