The Tegra PMC device tree bindings don't support the "#wake-cells" and
"nvidia,reset-gpio" properties, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AS3722 pinmux device tree node doesn't have a "reg" property and
therefore must not have a unit-address, so drop it.
While at it, add missing unit-addresses for the charger and smart
battery IC's on the ChromeOS embedded controller's I2C tunnel bus.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add the
device tree node on Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regulators defined at the top level in device tree are no longer part of
a simple bus and therefore don't have a reg property. Nodes without a
reg property shouldn't have a unit-address either, so drop the unit
address from the node names. To ensure nodes aren't duplicated (in which
case they would end up merged in the final DTB), append the name of the
regulator to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks defined at the top level in device tree are no longer part of a
simple bus and therefore don't have a reg property. Nodes without a reg
property shouldn't have a unit-address either, so drop the unit address
from the node names. To ensure nodes aren't duplicated (in which case
they would end up merged in the final DTB), append the name of the clock
to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controllers are attached to a separate ARM SMMU instance
that is dedicated to servicing isochronous memory clients. Add this ISO
instance of the ARM SMMU to device tree.
Please note that the display controllers are not hooked up to this SMMU
yet, because we are still missing a means to transition framebuffers
used by the bootloader to the kernel.
This based upon an initial patch by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the device-tree nodes for NVENC and NVJPG Host1x engines on
Tegra186 and Tegra194.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support to enumerate SD in UHS mode on Tegra194. Add required
device-tree properties in SDMMC1 and SDMMC3 instances to enable dynamic
pad voltage switching and enumerate SD card in UHS-I modes.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson AGX Orin Developer Kit is a continuation of the Jetson
Developer Kit line using the new NVIDIA Tegra234 (Orin) SoC.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra234 SoC has 3 clusters of 4 Cortex-A78AE CPU cores each,
for a total of 12 CPUs. Each CPU has 64 KiB instruction and data caches
with each cluster having an additional 256 KiB unified L2 cache and a 2
MiB L3 cache.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These two controllers expose general purpose I/O pins that can be used
to control or monitor a variety of signals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device for TCU (Tegra Combined UART) used for serial console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing properties to the eMMC controller, as required to use it on
actual hardware.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On final Tegra234 systems, shared memory for communication with BPMP is
located at offset 0x70000 in SYSRAM.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This stable tag contains the addition of the EMC clock ID and an initial
list of memory client IDs for Tegra234 and will be shared between the
memory and ARM SoC trees.
-----BEGIN PGP SIGNATURE-----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=bl4k
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.17-dt-bindings-memory' into for-5.17/arm64/dt
dt-bindings: memory: Add Tegra234 support
This stable tag contains the addition of the EMC clock ID and an initial
list of memory client IDs for Tegra234 and will be shared between the
memory and ARM SoC trees.
If we have a list of requests in our plug list, send it to the driver in
one go, if possible. The driver must set mq_ops->queue_rqs() to support
this, if not the usual one-by-one path is used.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert the device tree bindings for the MISC register block found on
NVIDIA Tegra SoCs from plain text to json-schema format.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document the variant of the memory controller and external memory
controllers found on Tegra234 and add some memory client and SMMU
stream ID definitions for use in device tree files.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add YAML device tree bindings for the Tegra NVENC and NVJPG Host1x
engines.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The #interconnect-cells properties are required to hook up memory
clients to the MC/EMC in interconnects properties. Add a description for
these properties.
For the nested EMC controller, the list of required properties was
missing. Add it so that the validation can be more strict.
Also, allow multiple reg entries required by Tegra194 and later.
While at it, also remove the dummy BPMP node from the example because it
is incomplete and fails validation. It's also not necessary for this
file and the BPMP DT schema already has a full example.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra SoCs have extra on-chip RAM that can be used for inter-processor
communication. Tegra186 and later make use of it to establish a two-way
channel between the CCPLEX and BPMP. Add missing compatible strings for
Tegra186 and Tegra194 as well as a new compatible string for Tegra234.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a few more clocks that will be used in follow-up patches to enable
more functionality on Tegra234.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the compatible strings for the Jetson AGX Orin and the
corresponding developer kit.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add descriptions to entries that were missing one and don't try to
combine multiple entries into one to avoid confusion.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pointless to maintain a head/tail for the list, as we never need to
access the tail. Entries are always LIFO for cache hotness reasons.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The batched completions only deal with non-partial requests anyway,
and it doesn't deal with any requests that have errors. Add a completion
handler that assumes it's a full request and that it's all being ended
successfully.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The prima driver facilitates the direct programming of beacon filter tables via
SMD commands.
The purpose of beacon filters is quote:
/* When beacon filtering is enabled, firmware will
* analyze the selected beacons received during BMPS,
* and monitor any changes in the IEs as listed below.
* The format of the table is:
* - EID
* - Check for IE presence
* - Byte offset
* - Byte value
* - Bit Mask
* - Byte reference
*/
The default filter table looks something like this:
tBeaconFilterIe gaBcnFilterTable[12] =
{
{ WLAN_EID_DS_PARAMS, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_ERP_INFO, 0u, { 0u, 0u, 248u, 0u } },
{ WLAN_EID_EDCA_PARAM_SET, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_QOS_CAPA, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_CHANNEL_SWITCH, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_QUIET, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 1u, 0u, 248u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 2u, 0u, 235u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 5u, 0u, 253u, 0u } },
{ WLAN_EID_PWR_CONSTRAINT, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_OPMODE_NOTIF, 0u, { 0u, 0u, 0u, 0u } }
};
Add in an equivalent filter set as present in the prima Linux driver.
For now omit the beacon filter "rem" command as the driver does not have an
explicit call to that SMD command. The filter mask should only count when
we are inside BMPS anyway.
Replicating the ability to program the filter table gives us scope to add and
remove elements in future. For now though this patch makes the rote-copy of the
downstream Linux beacon filter table, which we can tweak as desired from now
on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-4-bryan.odonoghue@linaro.org
The comment in the header with respect to beacon filtering makes a
reference to "the structure above" and "the structure below" which would be
informative if the comment appeared in the right place but, it does not.
Fix the comment location so that it a least makes sense w/r/t the physical
location statements.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-3-bryan.odonoghue@linaro.org
The beacon filter structures need to be packed. Right now its fine because
we don't yet use these structures so just pack them without marking it for
backporting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-2-bryan.odonoghue@linaro.org
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2)
is reserved through DT entries for firmware usage. Send the base
address from DT entries.
If DT entry is available, PCI device will work with
fixed_mem_region else host allocates multiple segments.
IPQ8074 on HK10 board supports multiple PCI devices.
IPQ8074 + QCN9074 is tested with this patch.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638789319-2950-2-git-send-email-akolli@codeaurora.org
Ath11k driver supports PCI devices such as QCN9074/QCA6390.
Ath11k firmware uses host DDR memory, DT entry is used to
reserve host DDR memory regions, send these memory base
addresses using DT entries.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638789319-2950-1-git-send-email-akolli@codeaurora.org
Jay Chen reported that using a kdump kernel on a GICv4.1 system
results in a RAS error being delivered when the secondary kernel
configures the ITS's view of the new VPE table.
As it turns out, that's because each RD still has a pointer to
the previous instance of the VPE table, and that particular
implementation is very upset by seeing two bits of the HW that
should point to the same table with different values.
To solve this, let's invalidate any reference that any RD has to
the VPE table when discovering the RDs. The ITS can then be
programmed as expected.
Reported-by: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211214064716.21407-1-jkchen@linux.alibaba.com
Link: https://lore.kernel.org/r/20211216144804.1578566-1-maz@kernel.org
The find.h APIs are designed to be used only on unsigned long arguments.
This can technically result in a over-read, but it is harmless in this
case. Regardless, fix it to avoid the warning seen under -Warray-bounds,
which we'd like to enable globally:
In file included from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./include/linux/smp.h:13,
from ./include/linux/lockdep.h:14,
from ./include/linux/mutex.h:17,
from ./include/linux/notifier.h:14,
from ./include/linux/clk.h:14,
from drivers/irqchip/irq-ingenic-tcu.c:7:
drivers/irqchip/irq-ingenic-tcu.c: In function 'ingenic_tcu_intc_cascade':
./include/linux/find.h:40:23: warning: array subscript 'long unsigned int[0]' is partly outside array bounds of 'uint32_t[1]' {aka 'unsigned int[1]'} [-Warray-bounds]
40 | val = *addr & GENMASK(size - 1, offset);
| ^~~~~
drivers/irqchip/irq-ingenic-tcu.c:30:18: note: while referencing 'irq_reg'
30 | uint32_t irq_reg, irq_mask;
| ^~~~~~~
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211215232457.2069969-1-keescook@chromium.org
imx_gpcv2_instance will not be updated after init, so mark it with
__ro_after_init.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211214084711.1357325-1-peng.fan@oss.nxp.com
Florian Westphal says:
====================
fib: merge nl policies
v4: resend with fixed subject line. I preserved review tags
from David Ahern.
v3: drop first two patches, otherwise unchanged.
This series merges the different (largely identical) nla policies.
v2 also squashed the ->suppress() implementation, I've dropped this.
Problem is that it needs ugly ifdef'ry to avoid build breakage
with CONFIG_INET=n || IPV6=n.
Given that even microbenchmark doesn't show any noticeable improvement
when ->suppress is inlined (it uses INDIRECT_CALLABLE) i decided to toss
the patch instead of adding more ifdefs.
====================
Link: https://lore.kernel.org/r/20211216120507.3299-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that there is only one fib nla_policy there is no need to
keep the macro around. Place it where its used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The attributes are identical in all implementations so move the ipv4 one
into the core and remove the per-family nla policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The signal setup code and evlist__prepare_workload() can be used for
other subcommands. Let's move them out of the __cmd_ftrace(). Then
it doesn't need to pass argc and argv.
On the other hand, select_tracer() is specific to the 'trace'
subcommand so it'd better moving it into the __cmd_ftrace().
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Changbin Du <changbin.du@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211215185154.360314-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The registers for ARM and ARM64 are enumerated using two enums that have
the same name. In order to be able to import both headers, the name of
one can be replaced using the C preprocessor like so:
#define perf_event_arm_regs perf_event_arm64_regs
#include <asm/perf_regs.h>
#undef perf_event_arm_regs
This patch updates all imports of ARM64's perf_regs.h in order to
prevent the naming collision.
Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-csky@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Link: https://lore.kernel.org/r/20211207180653.1147374-3-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Refactors code for gathering PID infos, it creates the function
nsinfo__get_nspid() to parse process 'status' node in folder '/proc'.
Base on the refactoring, this patch introduces a new helper
nsinfo__is_in_root_namespace(), it returns true when the caller runs in
the root PID namespace.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: John Garry <john.garry@huawei.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonatan Goldschmidt <yonatan.goldschmidt@granulate.io>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211212134721.1721245-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There is a spelling mistake in a __T_VERBOSE message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-janitors@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211212222122.478537-1-colin.i.king@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use IS_ERR_OR_NULL() to make the code cleaner.
Also if the priv is NULL, it's improper to call PTR_ERR(priv).
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: unlisted-recipients
Link: http://lore.kernel.org/lkml/20211212135613.20000-1-linmq006@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>