Move the assertions requiring restart table searches under
CONFIG_PPC_IRQ_SOFT_MASK_DEBUG.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210922145452.352571-6-npiggin@gmail.com
Enabling MSR[EE] in interrupt handlers while interrupts are still soft
masked allows PMIs to profile interrupt handlers to some degree, beyond
what SIAR latching allows.
When perf is not being used, this is almost useless work. It requires an
extra mtmsrd in the irq handler, and it also opens the door to masked
interrupts hitting and requiring replay, which is more expensive than
just taking them directly. This effect can be noticable in high IRQ
workloads.
Avoid enabling MSR[EE] unless perf is currently in use. This saves about
60 cycles (or 8%) on a simple decrementer interrupt microbenchmark.
Replayed interrupts drop from 1.4% of all interrupts taken, to 0.003%.
This does prevent the soft-nmi interrupt being taken in these handlers,
but that's not too reliable anyway. The SMP watchdog will continue to be
the reliable way to catch lockups.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210922145452.352571-5-npiggin@gmail.com
Interrupt code enables MSR[EE] in some irq handlers while keeping local
irqs disabled via soft-mask, allowing PMI interrupts to be taken as
soft-NMI to improve profiling of irq handlers.
When perf is not enabled, there is no point to doing this, it's
additional overhead. So provide a function that can say if PMIs should
be taken promptly if possible.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210922145452.352571-4-npiggin@gmail.com
The mtmsrd to enable MSR[RI] can be combined with the mtmsrd to enable
MSR[EE] in interrupt entry code, for those interrupts which enable EE.
This helps performance of important synchronous interrupts (e.g., page
faults).
This is similar to what commit dd152f70bd ("powerpc/64s: system call
avoid setting MSR[RI] until we set MSR[EE]") does for system calls.
Do this by enabling EE and RI together at the beginning of the entry
wrapper if PACA_IRQ_HARD_DIS is clear, and only enabling RI if it is
set.
Asynchronous interrupts set PACA_IRQ_HARD_DIS, but synchronous ones
leave it unchanged, so by default they always get EE=1 unless they have
interrupted a caller that is hard disabled. When the sync interrupt
later calls interrupt_cond_local_irq_enable(), it will not require
another mtmsrd because MSR[EE] was already enabled here.
This avoids one mtmsrd L=1 for synchronous interrupts on 64s, which
saves about 20 cycles on POWER9. And for kernel-mode interrupts, both
synchronous and asynchronous, this saves an additional 40 cycles due to
the mtmsrd being moved ahead of mfspr SPRN_AMR, which prevents a SPR
scoreboard stall.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210922145452.352571-3-npiggin@gmail.com
Make synchronous interrupt handler entry wrappers enable MSR[EE] if
MSR[EE] was enabled in the interrupted context. IRQs are soft-disabled
at this point so there is no change to high level code, but it's a
masked interrupt could fire.
This is a performance disadvantage for interrupts which do not later
call interrupt_cond_local_irq_enable(), because an an additional mtmsrd
or wrtee instruction is executed. However the important synchronous
interrupts (e.g., page fault) do enable interrupts, so the performance
disadvantage is mostly avoided.
In the next patch, MSR[RI] enabling can be combined with MSR[EE]
enabling, which mitigates the performance drop for the former and gives
a performance advanage for the latter interrupts, on 64s machines. 64e
is coming along for the ride for now to avoid divergences with 64s in
this tricky code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210922145452.352571-2-npiggin@gmail.com
KVM does not support VAS so guests always print a useless error on boot
vas: HCALL(398) error -2, query_type 0, result buffer 0x57f2000
Change this to only print the message if the error is not H_FUNCTION.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211126052133.1664375-1-npiggin@gmail.com
The code represent memory/cache level data based on PERF_MEM_LVL_*
namespace, which is in the process of deprication in the favour of
newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields.
Add data source encodings to represent cache/memory data based on
newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields.
Add data source encodings to represent data coming from local
memory/Remote memory/distant memory and remote/distant cache hits.
In order to represent data coming from OpenCAPI cache/memory, we use
LVLNUM "PMEM" field which is used to present persistent memory accesses.
Result in power10 system with patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ............ ........................ .......................... ................
#
29.46% 2331 L1 or L1 hit [.] __random libc-2.28.so
23.11% 2121 L1 or L1 hit [.] producer_populate_cache producer_consumer
18.56% 1758 L1 or L1 hit [.] __random_r libc-2.28.so
15.64% 1559 L2 or L2 hit [.] __random libc-2.28.so
.....
0.09% 5 Remote socket, same board Any cache hit [.] __random libc-2.28.so
0.07% 4 Remote socket, same board Any cache hit [.] __random libc-2.28.so
.....
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211206091749.87585-5-kjain@linux.ibm.com
The code represent data coming from L1/L2/L3 cache hits based on
PERF_MEM_LVL_* namespace, which is in the process of deprecation in
the favour of newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_}
fields.
Add data source encodings to represent L1/L2/L3 cache hits based on
newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields for
power10 and older platforms
Result in power9 system without patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ............ ........................ ................................. ................
#
29.51% 1 L2 hit [k] perf_event_exec [kernel.vmlinux]
27.05% 1 L1 hit [k] perf_ctx_unlock [kernel.vmlinux]
13.93% 1 L1 hit [k] vtime_delta [kernel.vmlinux]
13.11% 1 L1 hit [k] prepend_path.isra.11 [kernel.vmlinux]
8.20% 1 L1 hit [.] 00000038.plt_call.__GI_strlen libc-2.28.so
8.20% 1 L1 hit [k] perf_event_interrupt [kernel.vmlinux]
Result in power9 system with patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ............ ........................ .......................... ................
#
36.63% 1 L2 or L2 hit [k] perf_event_exec [kernel.vmlinux]
25.50% 1 L1 or L1 hit [k] vtime_delta [kernel.vmlinux]
13.12% 1 L1 or L1 hit [k] unmap_region [kernel.vmlinux]
12.62% 1 L1 or L1 hit [k] perf_sample_event_took [kernel.vmlinux]
6.93% 1 L1 or L1 hit [k] perf_ctx_unlock [kernel.vmlinux]
5.20% 1 L1 or L1 hit [.] __memcpy_power7 libc-2.28.so
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211206091749.87585-4-kjain@linux.ibm.com
Add new macros for mem_hops field which can be used to
represent remote-node, socket and board level details.
Currently the code had macro for HOPS_0, which corresponds
to data coming from another core but same node.
Add new macros for HOPS_1 to HOPS_3 to represent
remote-node, socket and board level data.
For ex: Encodings for mem_hops fields with L2 cache:
L2 - local L2
L2 | REMOTE | HOPS_0 - remote core, same node L2
L2 | REMOTE | HOPS_1 - remote node, same socket L2
L2 | REMOTE | HOPS_2 - remote socket, same board L2
L2 | REMOTE | HOPS_3 - remote board L2
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211206091749.87585-2-kjain@linux.ibm.com
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-15
This series contains updates to igb, igbvf, igc and ixgbe drivers.
Karen moves checks for invalid VF MAC filters to occur earlier for
igb.
Letu Ren fixes a double free issue in igbvf probe.
Sasha fixes incorrect min value being used when calculating for max for
igc.
Robert Schlabbach adds documentation on enabling NBASE-T support for
ixgbe.
Cyril Novikov adds missing initialization of MDIO bus speed for ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
t-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-12-15
This series contains updates to ice driver only.
Jake makes changes to flash update. This includes the following:
* a new shadow-ram region similar to NVM region but for the device shadow
RAM contents. This is distinct from NVM region because shadow RAM is
built up during device init and may be different from the raw NVM flash
data.
* refactoring of the ice_flash_pldm_image to become the main flash update
entry point. This is simpler than having both an
ice_devlink_flash_update and an ice_flash_pldm_image. It will make
additions like dry-run easier in the future.
* reducing time to read Option ROM version information.
* adding support for firmware activation via devlink reload, when
possible.
The major new work is the reload support, which allows activating firmware
immediately without a reboot when possible. Reload support only supports
firmware activation.
Jesse improves transmit code: utilizing newer netif_tx* API, adding some
prefetch calls, correcting expected conditions when calling ice_vsi_down(),
and utilizing __netdev_tx_sent_queue() call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BT601/BT709 color encoding and limited vs full
range properties were not being exposed, defaulting
always to BT601 limited range.
Expose the parameters and set the registers appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20211215091739.135042-4-maxime@cerno.tech
The P030 format, used with the DRM_FORMAT_MOD_BROADCOM_SAND128 modifier,
is a format output by the video decoder on the BCM2711.
Add native support to the KMS planes for that format.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20211215091739.135042-3-maxime@cerno.tech
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit word (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20211215091739.135042-2-maxime@cerno.tech
Saeed Mahameed says:
====================
mlx5-next branch 2021-12-15
Hi Dave, Jakub, Jason
This pulls mlx5-next branch into net-next and rdma branches.
All patches already reviewed on both rdma and netdev mailing lists.
Please pull and let me know if there's any problem.
1) Add multiple FDB steering priorities [1]
2) Introduce HW bits needed to configure MAC list size of VF/SF.
Required for ("net/mlx5: Memory optimizations") upcoming series [2].
[1] https://lore.kernel.org/netdev/20211201193621.9129-1-saeed@kernel.org/
[2] https://lore.kernel.org/lkml/20211208141722.13646-1-shayd@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eqos ethernet support five queues on hardware, enable these queues and
configure the priority of each queue. Uses Strict Priority as scheduling
algorithms to ensure that the TSN function works.
The priority of each queue is a bitmask value that maps VLAN tag
priority to the queue. Since the hardware only supports five queues,
this patch maps priority 0-4 to queues one by one, and priority 5-7 to
queue 4.
The total fifo size of 5 queues is 8192 bytes, if enable 5 queues with
store-and-forward mode, it's not enough for large packets, which would
trigger fifo overflow frequently. This patch set DMA to thresh mode to
enable all 5 queues.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PEB-AV-02 expansion adapter extends the phyBOARD-Mira boards to
connect parallel LCD displays, either with capacitive or resistive
touch.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PHYTEC PEV-EVAL-01 expansion board adds support for additional
gpio-triggered user-leds and gpio-key support.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add XRGB8888 emulation support for devices that can only do XRGB2101010.
This is chiefly useful for simpledrm on Apple devices where the
bootloader-provided framebuffer is 10-bit.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211212062407.138309-3-marcan@marcan.st
Add overlays for various serdes protocols on LS1028A QDS board using
different PHY cards. These should be applied at boot, based on serdes
configuration. If no overlay is applied, only the RGMII interface on
the QDS is available in Linux.
Building device tree fragments requires passing the "-@" argument to
dtc, which increases the base dtb size and might cause some platforms to
fail to store the new binary. To avoid that, it would be nice to only
pass "-@" for the platforms where fragments will be used, aka
LS1028A-QDS. One approach suggested by Rob Herring is used here:
https://lore.kernel.org/patchwork/patch/821645/
Also moved the enet* override nodes in dts file to be in alphabetic order.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c rtc is on i2c2 bus not i2c1 bus, so fix it in dts.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.lil@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable pwm0 on ls1028a-rdb board which uses flextimer1.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pwm nodes using flextimer controller.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flextimer2 based ftm_alarm1 node and enable it to be the default rtc
wakeup source for rdb and qds boards instead of the original flextimer1
which is used by PWM. The ftm_alarm0 node hence is disabled by default.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe EP nodes for ls1028a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This code is required for both simplefb and simpledrm, so let's move it
into the OF core instead of having it as an ad-hoc initcall in the
drivers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211212062407.138309-2-marcan@marcan.st
This selects the rtc-gamecube driver, which provides a real-time clock
on this platform.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211215175501.6761-5-linkmauve@linkmauve.fr
I haven’t been able to test this patch as all of my consoles have a
working RTC battery, but according to the documentation it should work
like that.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211215175501.6761-3-linkmauve@linkmauve.fr
These three consoles share a device, the MX23L4005, which contains a
clock and 64 bytes of SRAM storage, and is exposed on the EXI bus
(similar to SPI) on channel 0, device 1. This driver allows it to be
used as a Linux RTC device, where time can be read and set.
The hardware also exposes two timers, one which shuts down the console
and one which powers it on, but these aren’t supported currently.
On the Wii U, the counter bias is stored in a XML file, /config/rtc.xml,
encrypted in the SLC (eMMC storage), using a proprietary filesystem. In
order to avoid having to implement all that, this driver assumes a
bootloader will parse this XML file and write the bias into the SRAM, at
the same location the other two consoles have it.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211215175501.6761-2-linkmauve@linkmauve.fr
Add USB overcurrent pin muxing on SoM layer. On DRC02 and PDK2 the USB
overcurrent pin isn't connected, but a USB hub on the board takes care
of the USB overcurrent instead. Therefore disable it there with the
property disable-over-current.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add interrupt line for RTC node on lx2162a-qds
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The default NXP SDHC adapter cards for LX2162AQDS are SD 2.0/3.0
adapter card for eSDHC1, and eMMC 5.1 adapter card for eSDHC2.
Add speed modes properties supported by the two adapters in device
tree node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable USB3 HW LPM feature for lx2160a.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two external MDIO buses used to communicate with phy devices that
are external to SOC are muxed in LX2160AQDS board. These buses can be
routed to any one of the eight IO slots on LX2160AQDS board depending on
value in fpga register 0x54. Additionally the external MDIO1 is used to
communicate to the onboard RGMII phy devices. The mdio1 is controlled
by bits 4-7 of fpga register and mdio2 is controlled by bits 4-7 of fpga
register.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disabled by default in SoC dtsi and enables in board dts files.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, and configure bus flags based on this DT property.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211017001204.299940-2-marex@denx.de
The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, to define the pixel data sampling edge.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211017001204.299940-1-marex@denx.de
The wakeup and sleep commands need to be sent to the WILC chip only
when it is in power save mode (PSM, as controlled by "iw dev wlan0 set
power_save on/off"). The commands are relatively costly, so it pays
to skip them when possible.
iperf3 without this patch (no significant different with PSM on/off):
TX 0.00-120.01 sec 140 MBytes 9.82 Mbits/sec
RX 0.00-120.69 sec 283 MBytes 19.6 Mbits/sec
with this patch applied:
PSM off (TX is 46% improved, RX slightly improved; may not be significant):
TX 0.00-120.00 sec 206 MBytes 14.4 Mbits/sec
RX 0.00-120.48 sec 322 MBytes 22.4 Mbits/sec
PSM on (no significant change):
TX 0.00-120.00 sec 140 MBytes 9.78 Mbits/sec
RX 0.00-120.08 sec 257 MBytes 18.0 Mbits/sec
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211210203016.3680425-2-davidm@egauge.net
Since the tee subsystem does not keep a strong reference to its idle
shared memory buffers, it races with other threads that try to destroy a
shared memory through a close of its dma-buf fd or by unmapping the
memory.
In tee_shm_get_from_id() when a lookup in teedev->idr has been
successful, it is possible that the tee_shm is in the dma-buf teardown
path, but that path is blocked by the teedev mutex. Since we don't have
an API to tell if the tee_shm is in the dma-buf teardown path or not we
must find another way of detecting this condition.
Fix this by doing the reference counting directly on the tee_shm using a
new refcount_t refcount field. dma-buf is replaced by using
anon_inode_getfd() instead, this separates the life-cycle of the
underlying file from the tee_shm. tee_shm_put() is updated to hold the
mutex when decreasing the refcount to 0 and then remove the tee_shm from
teedev->idr before releasing the mutex. This means that the tee_shm can
never be found unless it has a refcount larger than 0.
Fixes: 967c9cca2c ("tee: generic TEE subsystem")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lars Persson <larper@axis.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reported-by: Patrik Lantz <patrik.lantz@axis.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
This fix is similar to commit 77c91295ea ("wil6210: specify max. IE
length"). Without the max IE length set, wpa_supplicant cannot operate
using the nl80211 interface.
This patch is a workaround - the number 512 is taken from the wlcore
driver, but note that per Paul Fertser:
there's no correct number because the driver will ignore the data
passed in extra IEs.
Suggested-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211212221310.5453-1-merlijn@wizzup.org
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
-----BEGIN PGP SIGNATURE-----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=tgbw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
first set of iwlwifi patches for v5.17
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
The base i.MX8MM dtsi changes the audio PLL2 rate, which gets in the
way if it should be used for anything else than audio. As this PLL doesn't
seem to be used by any upstream supported board, just remove the rate
configuration to allow boards to set it up as they wish.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>