The original patch adding the example used _DSC Name when Method was
intended. Fix this.
Also replace spaces used for indentation with tabs in the example.
Fixes: ed66f12ba4 ("Documentation: ACPI: Document _DSC object usage for enum power state")
Reported-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.
Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.
To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org
It's more descriptive to use the actual enum used by the firmware instead of a
boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org
The kdocs were copied from another device_id struct and not adapted.
Fixes: fa443bc3c1 ("HID: intel-ish-hid: add support for MODULE_DEVICE_TABLE()")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the helper macro SET_RUNTIME_PM_OPS() instead of the verbose
operators ".runtime_suspend/.runtime_resume", because the
SET_RUNTIME_PM_OPS() is a nice helper macro that could be brought
in to make code a little more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210907033526.1612-1-caihuoqing@baidu.com
DSS5's maximum tv pclk rate (i.e. HDMI) is set to 186MHz, which comes
from the TRM (DPLL_HDMI_CLK1 frequency must be lower than 186 MHz). To
support DRA76's wide screen HDMI feature, we need to increase this
maximum rate.
Testing shows that the PLL seems to work fine even with ~240MHz clocks,
and even the HDMI output at that clock is stable enough for monitors to
show a picture. This holds true for all DRA7 and AM5 SoCs (and probably
also for OMAP5).
However, the highest we can go without big refactoring to the clocking
code is 192MHz, as that is the DSS func clock we get from the PRCM. So,
increase the max HDMI pixel clock to 192MHz for now, to allow some more
2k+ modes to work.
This patch never had a clear confirmation from HW people, but this
change stayed on production trees for multiple years without any report
on an eventual breakage.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211012133939.2145462-1-narmstrong@baylibre.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210831135707.4676-1-caihuoqing@baidu.com
Use the helper macro SET_RUNTIME_PM_OPS() instead of the verbose
operators ".runtime_suspend/.runtime_resume", because the
SET_RUNTIME_PM_OPS() is a nice helper macro that could be brought
in to make code a little clearer, a little more concise.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210828084811.104-1-caihuoqing@baidu.com
When the reply for a non-blocking transmit arrives, the sequence
field for that reply was never filled in, so userspace would have no
way of associating the reply to the original transmit.
Copy the sequence field to ensure that this is now possible.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 0dbacebede ([media] cec: move the CEC framework out of staging and to media)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit a4b83deb3e ("media: videobuf2: rework vb2_mem_ops API")
added a new vb member to struct vb2_dma_sg_buf, but it only added
code setting this to the vb2_dma_sg_alloc() function and not to the
vb2_dma_sg_get_userptr() and vb2_dma_sg_attach_dmabuf() which also
create vb2_dma_sg_buf objects.
This is causing a crash due to a NULL pointer deref when using
libcamera on devices with an Intel IPU3 (qcam app).
Fix these crashes by assigning buf->vb in the other 2 functions too,
note libcamera tests the vb2_dma_sg_get_userptr() path, the change
to the vb2_dma_sg_attach_dmabuf() path is untested.
Fixes: a4b83deb3e ("media: videobuf2: rework vb2_mem_ops API")
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
My previous bugfix addressed an API inconsistency found by syzbot,
and it correctly fixed the issue on x86-64 machines, which now behave
correctly for both native and compat tasks.
Unfortunately, John found that the patch broke compat mode on all other
architectures, as they can no longer rely on the VIDIOC_DQEVENT_TIME32
code from the native handler as a fallback in the compat code.
The best way I can see for addressing this is to generalize the
VIDIOC_DQEVENT32_TIME32 code from x86 and use that for all architectures,
leaving only the VIDIOC_DQEVENT32 variant as x86 specific. The original
code was trying to be clever and use the same conversion helper for native
32-bit code and compat mode, but that turned out to be too obscure so
even I missed that bit I had introduced myself when I made the fix.
Fixes: c344f07aa1 ("media: v4l2-core: ignore native time32 ioctls on 64-bit")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit 991d9557b0 ("drm/i915/tgl/dsi: Gate the ddi clocks
after pll mapping"). The Bspec was updated recently with the pll ungate
sequence similar to that of icl dsi enable sequence. Hence reverting.
Bspec: 49187
Fixes: 991d9557b0 ("drm/i915/tgl/dsi: Gate the ddi clocks after pll mapping")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109120428.15211-1-vandita.kulkarni@intel.com
The HID descriptor of many of Wacom's touch input devices include a
"Confidence" usage that signals if a particular touch collection contains
useful data. The driver does not look at this flag, however, which causes
even invalid contacts to be reported to userspace. A lucky combination of
kernel event filtering and device behavior (specifically: contact ID 0 ==
invalid, contact ID >0 == valid; and order all data so that all valid
contacts are reported before any invalid contacts) spare most devices from
any visibly-bad behavior.
The DTH-2452 is one example of an unlucky device that misbehaves. It uses
ID 0 for both the first valid contact and all invalid contacts. Because
we report both the valid and invalid contacts, the kernel reports that
contact 0 first goes down (valid) and then goes up (invalid) in every
report. This causes ~100 clicks per second simply by touching the screen.
This patch inroduces new `confidence` flag in our `hid_data` structure.
The value is initially set to `true` at the start of a report and can be
set to `false` if an invalid touch usage is seen.
Link: https://github.com/linuxwacom/input-wacom/issues/270
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two error paths need to drop the lock before returning.
Fixes: c5e6267695 ("HID: nintendo: add player led support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some selftests assume that nothing will attempt to grab these bitlocks
while they are held by the selftests. With GuC, for example, that is
not true because the hanging workloads may cause the GuC code to attempt
to grab them for a global reset, and that may cause it to end up
sleeping on the bit never waking up. Regardless whether that will be
the final solution for GuC, use clear_and_wake_up_bit() pending a more
thorough investigation on how this should be handled moving forward.
To be clear this needs to be a temporary solution. If we can't find
an in-kernel locking primitive to use here, we should at the very least
add lockdep annotation to these bitlocks with a thorough explanation
as to why we need to use bits.
v3:
- Use GEM_BUG_ON(test_and_set_bit()) rather than set_bit() to verify
the assumption that nothing is holding the reset locks when we
attempt to grab them. (Chris Wilson)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105150146.834052-1-thomas.hellstrom@linux.intel.com
Gem-TTM objects that are backed by shmem might have populated
page-vectors without having the GEM pages set. Those objects
aren't moved to the correct shrinker / purge list by gem_madvise.
For such objects, identified by having the
_SELF_MANAGED_SHRINK_LIST set, make sure they end up on the
correct list.
v2:
- Revert a change that made swapped-out objects inaccessible for
truncating. (Matthew Auld)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211108123637.929617-1-thomas.hellstrom@linux.intel.com
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 4873586278 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The comment about the reused vmalloc helpers is no longer valid after
the recent change for the noncontig allocator. Drop the stale
comment.
Fixes: ad4f93ca41 ("ALSA: memalloc: Use proper SG helpers for noncontig allocations")
Link: https://lore.kernel.org/r/20211110063100.21359-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With commit 506c1da44f ("cifs: use the expiry output of dns_query to
schedule next resolution") and after triggering the first reconnect,
the next async dns resolution of tcp server's hostname would be
scheduled based on dns_resolver's key expiry default, which happens to
default to 5s on most systems that use key.dns_resolver for upcall.
As per key.dns_resolver.conf(5):
default_ttl=<number>
The number of seconds to set as the expiration on a cached
record. This will be overridden if the program manages to re-
trieve TTL information along with the addresses (if, for exam-
ple, it accesses the DNS directly). The default is 5 seconds.
The value must be in the range 1 to INT_MAX.
Make the next async dns resolution no shorter than 120s as we do not
want to be upcalling too often.
Cc: stable@vger.kernel.org
Fixes: 506c1da44f ("cifs: use the expiry output of dns_query to schedule next resolution")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Make two separate functions that handle dfs and non-dfs reconnect
logics since cifs_reconnect() became way too complex to handle both.
While at it, add some documentation.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20211108201817.43121-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
blank screen and other display rates fixes, and more.
Four patches targeting stable in here.
Display Fixes:
- DP rates related fixes (Imre, Jani)
- A Revert on disaling dual eDP that was causing state readout problems (Jani)
- put the cdclk vtables in const data (Jani)
- Fix DVO port type for moder platforms (Ville)
- Fix blankscreen by turning DP++ TMDS output buffers on encoder->shutdown (Ville)
- CCS FBs related fixes (Imre)
GT fixes:
- Fix recursive lock in GuC submission (Matt Brost)
- Revert guc_id from i915_request tracepoint (Joonas)
- Build fix around dmabuf (Matt Auld)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmGLAXwACgkQ+mJfZA7r
E8rCbwf9EDwnn35GYmATgf0wDiXmZRJHlFqRgLcPs5o9P+4MXDvPAKINCTXJBxr6
+TpA+ZYsTHh58P9FmoGLu1btBasEACjeoiMFL5u4RVUPOQUd0qwBmXHjSHzJ+y6E
eA8hrtYVVfc9/Z3QFLybxyZNzw8s7a9BUZoBCjr0AiUfp0BdqzplIU2LpnsPyw9S
Q7UbMRyiMNd7iOndVCamfDnTbVBFRvv6WEbxveCjLL3ud02fpWywBN+CryQ3ZQs0
5gco7H/gpCrLHysJbBa60DPM6NL0JKxXvRU0aSXP2WY6ONFzc6jULYYtkRLMHjc3
NLuQlx5uBCf863h6k3shIzlNHCvF+Q==
=aRFO
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-fixes-2021-11-09' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Couple Reverts, build fix, couple virtualization fixes,
blank screen and other display rates fixes, and more.
Four patches targeting stable in here.
Display Fixes:
- DP rates related fixes (Imre, Jani)
- A Revert on disaling dual eDP that was causing state readout problems (Jani)
- put the cdclk vtables in const data (Jani)
- Fix DVO port type for moder platforms (Ville)
- Fix blankscreen by turning DP++ TMDS output buffers on encoder->shutdown (Ville)
- CCS FBs related fixes (Imre)
GT fixes:
- Fix recursive lock in GuC submission (Matt Brost)
- Revert guc_id from i915_request tracepoint (Joonas)
- Build fix around dmabuf (Matt Auld)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YYsBif3HMi8GjLoU@intel.com
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYYTgewAKCRDj7w1vZxhR
xafyAP4wA76Bmx4yvNXMoeD8ptKGzNfioK2Dg4JLDxbfOspt3gEA+jLfCFZ/UZD0
6lJxH0nJmRkA9rAg5TWl98YqiF3iYg0=
=7kMT
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2021-11-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
A refcounting fix for outstanding fence callbacks.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105074318.oy6rwjr5wcw6qpjj@gilmour
Model 88E6191X only supports >1G speeds on port 10. Port 0 and 9 are
only 1G.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211104171747.10509-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert list_for_each{,_safe} to list_for_each_entry{,_safe} in
cifs_mark_tcp_ses_conns_for_reconnect() function.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Create cifs_mark_tcp_ses_conns_for_reconnect() helper to mark all
sessions and tcons for reconnect when reconnecting tcp server.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reorder the parameters in seq_printf() to correctly print header
flags.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Now that we have done a spring cleaning on all drivers and added
error checking / handling, let's keep it that way and ensure
no new drivers fail to stick with it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20211110002949.999380-1-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kernel test robot reports that we now trigger some sparse warnings:
block/blk-mq.h:169:32: sparse: sparse: restricted req_flags_t degrades to integer
block/blk-mq.h:169:32: sparse: sparse: restricted req_flags_t degrades to integer
block/blk-mq.h:169:32: sparse: sparse: restricted req_flags_t degrades to integer
which is due to ->rq_flags being an unsigned int, rather than the
stronger type req_flags_t enum.
Change the type to req_flags_t to silence this warning.
Fixes: 56f8da642b ("block: add rq_flags to struct blk_mq_alloc_data")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver has its own sysfs file to adjust the clock. Fortunately, it is
already in pbb, however, the sign it expects is the opposite of what the
RTC core does (which actually aligns with the RTC).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-12-alexandre.belloni@bootlin.com
Tell the RTC core UIE are not supported because the resolution of the alarm
is a minute.
Note that this is in fact also fixing how the resolution is reported as the
previous test was simply ensuring the alarm was more than a minute in the
future while the register has a minute resolution.
This would be ok if the alarm was a countdown but ab8500_rtc_read_alarm
suggests otherwise and the AB8500 datasheet states that the RTC
documentation is not public.
Finally, the comment is wrong and what makes the UIE emulation work is
uie_unsupported being set.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211107225458.111068-6-alexandre.belloni@bootlin.com
Handle alarms with a minute resolution in the core. Until now drivers have
been open coding the seconds part removal and have been doing that wrongly.
Most of them are rounding up which means the allow the system to miss
deadlines. So, round down and let __rtc_set_alarm return immediately if the
time has already passed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-1-alexandre.belloni@bootlin.com