Commit graph

1,072,133 commits

Author SHA1 Message Date
lianzhi chang
fb09d0ac07 tty: Fix the keyboard led light display problem
Use the "ctrl+alt+Fn" key combination to switch the system from tty to
desktop or switch the system from desktop to tty. After the switch is
completed, it is found that the state of the keyboard lock is
inconsistent with the state of the keyboard Led light.The reasons are
as follows:

* The desktop environment (Xorg and other services) is bound to a tty
  (assuming it is tty1), and the kb->kbdmode attribute value of tty1
  will be set to VC_OFF. According to the current code logic, in the
  desktop environment, the values of ledstate and kb->ledflagstate
  of tty1 will not be modified anymore, so they are always 0.

* When switching between each tty, the final value of ledstate set by
  the previous tty is compared with the kb->ledflagstate value of the
  current tty to determine whether to set the state of the keyboard
  light. The process of switching between desktop and tty is also the
  process of switching between tty1 and other ttys. There are two
  situations:

  - (1) In the desktop environment, tty1 will not set the ledstate,
  which will cause when switching from the desktop to other ttys,
  if the desktop lights up the keyboard's led, after the switch is
  completed, the keyboard's led light will always be on;

  - (2) When switching from another tty to the desktop, this
  mechanism will trigger tty1 to set the led state. If other tty
  lights up the led of the keyboard before switching to the desktop,
  the led will be forcibly turned off. This situation should
  be avoided.

* The current patch is to solve these problems: When VT is switched,
  the keyboard led needs to be set once.Ensure that after the
  switch is completed, the state of the keyboard LED is consistent
  with the state of the keyboard lock.

Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: lianzhi chang <changlianzhi@uniontech.com>
Link: https://lore.kernel.org/r/20211215125125.10554-1-changlianzhi@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:19:14 +01:00
Xianwei Zhao
34de666684 dt-bindings: serial: amlogic, meson-uart: support S4
Add serial bindings support menson S4 SoC family.

Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/r/20211221030146.522-1-xianwei.zhao@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:18:49 +01:00
Andy Shevchenko
d6d9d17aba tty: tty_io: Switch to vmalloc() fallback in case of TTY_NO_WRITE_SPLIT
When TTY_NO_WRITE_SPLIT is set and 64 KiB chunks are used, allow
vmalloc() fallback. Supply __GFP_RETRY_MAYFAIL to make kmalloc()
preferable over vmalloc() since we may want a better performance.

Note, both current users copy data to another buffer anyway, so
the type of our allocation doesn't affect their expectations.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211220133250.3070-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:18:44 +01:00
Xiang wangx
e822b4973f tty/ldsem: Fix syntax errors in comments
Delete the redundant word 'are'.

Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20211208142036.7956-1-wangxiang@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:15:49 +01:00
Chunfeng Yun
43f3b8cbcf usb: mtu3: set interval of FS intr and isoc endpoint
Add support to set interval also for FS intr and isoc endpoint.

Fixes: 4d79e042ed ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:05:45 +01:00
Chunfeng Yun
8c313e3bfd usb: mtu3: fix list_head check warning
This is caused by uninitialization of list_head.

BUG: KASAN: use-after-free in __list_del_entry_valid+0x34/0xe4

Call trace:
dump_backtrace+0x0/0x298
show_stack+0x24/0x34
dump_stack+0x130/0x1a8
print_address_description+0x88/0x56c
__kasan_report+0x1b8/0x2a0
kasan_report+0x14/0x20
__asan_load8+0x9c/0xa0
__list_del_entry_valid+0x34/0xe4
mtu3_req_complete+0x4c/0x300 [mtu3]
mtu3_gadget_stop+0x168/0x448 [mtu3]
usb_gadget_unregister_driver+0x204/0x3a0
unregister_gadget_item+0x44/0xa4

Fixes: 83374e035b ("usb: mtu3: add tracepoints to help debug")
Cc: stable@vger.kernel.org
Reported-by: Yuwen Ng <yuwen.ng@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:05:45 +01:00
Chunfeng Yun
a7aae769ca usb: mtu3: add memory barrier before set GPD's HWO
There is a seldom issue that the controller access invalid address
and trigger devapc or emimpu violation. That is due to memory access
is out of order and cause gpd data is not correct.
Add mb() to prohibit compiler or cpu from reordering to make sure GPD
is fully written before setting its HWO.

Fixes: 48e0d3735a ("usb: mtu3: supports new QMU format")
Cc: stable@vger.kernel.org
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:05:44 +01:00
Chunfeng Yun
e3d4621c22 usb: mtu3: fix interval value for intr and isoc
Use the Interval value from isoc/intr endpoint descriptor, no need
minus one. The original code doesn't cause transfer error for
normal cases, but it may have side effect with respond time of ERDY
or tPingTimeout.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:05:44 +01:00
Vincent Pelletier
b1e0887379 usb: gadget: f_fs: Clear ffs_eventfd in ffs_data_clear.
ffs_data_clear is indirectly called from both ffs_fs_kill_sb and
ffs_ep0_release, so it ends up being called twice when userland closes ep0
and then unmounts f_fs.
If userland provided an eventfd along with function's USB descriptors, it
ends up calling eventfd_ctx_put as many times, causing a refcount
underflow.
NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls.

Also, set epfiles to NULL right after de-allocating it, for readability.

For completeness, ffs_data_clear actually ends up being called thrice, the
last call being before the whole ffs structure gets freed, so when this
specific sequence happens there is a second underflow happening (but not
being reported):

/sys/kernel/debug/tracing# modprobe usb_f_fs
/sys/kernel/debug/tracing# echo ffs_data_clear > set_ftrace_filter
/sys/kernel/debug/tracing# echo function > current_tracer
/sys/kernel/debug/tracing# echo 1 > tracing_on
(setup gadget, run and kill function userland process, teardown gadget)
/sys/kernel/debug/tracing# echo 0 > tracing_on
/sys/kernel/debug/tracing# cat trace
 smartcard-openp-436     [000] .....  1946.208786: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .....  1946.279147: ffs_data_clear <-ffs_data_closed
 smartcard-openp-431     [000] .n...  1946.905512: ffs_data_clear <-ffs_data_put

Warning output corresponding to above trace:
[ 1946.284139] WARNING: CPU: 0 PID: 431 at lib/refcount.c:28 refcount_warn_saturate+0x110/0x15c
[ 1946.293094] refcount_t: underflow; use-after-free.
[ 1946.298164] Modules linked in: usb_f_ncm(E) u_ether(E) usb_f_fs(E) hci_uart(E) btqca(E) btrtl(E) btbcm(E) btintel(E) bluetooth(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) bcm2835_v4l2(CE) bcm2835_mmal_vchiq(CE) videobuf2_vmalloc(E) videobuf2_memops(E) sha512_generic(E) videobuf2_v4l2(E) sha512_arm(E) videobuf2_common(E) videodev(E) cpufreq_dt(E) snd_bcm2835(CE) brcmfmac(E) mc(E) vc4(E) ctr(E) brcmutil(E) snd_soc_core(E) snd_pcm_dmaengine(E) drbg(E) snd_pcm(E) snd_timer(E) snd(E) soundcore(E) drm_kms_helper(E) cec(E) ansi_cprng(E) rc_core(E) syscopyarea(E) raspberrypi_cpufreq(E) sysfillrect(E) sysimgblt(E) cfg80211(E) max17040_battery(OE) raspberrypi_hwmon(E) fb_sys_fops(E) regmap_i2c(E) ecdh_generic(E) rfkill(E) ecc(E) bcm2835_rng(E) rng_core(E) vchiq(CE) leds_gpio(E) libcomposite(E) fuse(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) crc32c_generic(E) sdhci_iproc(E) sdhci_pltfm(E) sdhci(E)
[ 1946.399633] CPU: 0 PID: 431 Comm: smartcard-openp Tainted: G         C OE     5.15.0-1-rpi #1  Debian 5.15.3-1
[ 1946.417950] Hardware name: BCM2835
[ 1946.425442] Backtrace:
[ 1946.432048] [<c08d60a0>] (dump_backtrace) from [<c08d62ec>] (show_stack+0x20/0x24)
[ 1946.448226]  r7:00000009 r6:0000001c r5:c04a948c r4:c0a64e2c
[ 1946.458412] [<c08d62cc>] (show_stack) from [<c08d9ae0>] (dump_stack+0x28/0x30)
[ 1946.470380] [<c08d9ab8>] (dump_stack) from [<c0123500>] (__warn+0xe8/0x154)
[ 1946.482067]  r5:c04a948c r4:c0a71dc8
[ 1946.490184] [<c0123418>] (__warn) from [<c08d6948>] (warn_slowpath_fmt+0xa0/0xe4)
[ 1946.506758]  r7:00000009 r6:0000001c r5:c0a71dc8 r4:c0a71e04
[ 1946.517070] [<c08d68ac>] (warn_slowpath_fmt) from [<c04a948c>] (refcount_warn_saturate+0x110/0x15c)
[ 1946.535309]  r8:c0100224 r7:c0dfcb84 r6:ffffffff r5:c3b84c00 r4:c24a17c0
[ 1946.546708] [<c04a937c>] (refcount_warn_saturate) from [<c0380134>] (eventfd_ctx_put+0x48/0x74)
[ 1946.564476] [<c03800ec>] (eventfd_ctx_put) from [<bf5464e8>] (ffs_data_clear+0xd0/0x118 [usb_f_fs])
[ 1946.582664]  r5:c3b84c00 r4:c2695b00
[ 1946.590668] [<bf546418>] (ffs_data_clear [usb_f_fs]) from [<bf547cc0>] (ffs_data_closed+0x9c/0x150 [usb_f_fs])
[ 1946.609608]  r5:bf54d014 r4:c2695b00
[ 1946.617522] [<bf547c24>] (ffs_data_closed [usb_f_fs]) from [<bf547da0>] (ffs_fs_kill_sb+0x2c/0x30 [usb_f_fs])
[ 1946.636217]  r7:c0dfcb84 r6:c3a12260 r5:bf54d014 r4:c229f000
[ 1946.646273] [<bf547d74>] (ffs_fs_kill_sb [usb_f_fs]) from [<c0326d50>] (deactivate_locked_super+0x54/0x9c)
[ 1946.664893]  r5:bf54d014 r4:c229f000
[ 1946.672921] [<c0326cfc>] (deactivate_locked_super) from [<c0326df8>] (deactivate_super+0x60/0x64)
[ 1946.690722]  r5:c2a09000 r4:c229f000
[ 1946.698706] [<c0326d98>] (deactivate_super) from [<c0349a28>] (cleanup_mnt+0xe4/0x14c)
[ 1946.715553]  r5:c2a09000 r4:00000000
[ 1946.723528] [<c0349944>] (cleanup_mnt) from [<c0349b08>] (__cleanup_mnt+0x1c/0x20)
[ 1946.739922]  r7:c0dfcb84 r6:c3a12260 r5:c3a126fc r4:00000000
[ 1946.750088] [<c0349aec>] (__cleanup_mnt) from [<c0143d10>] (task_work_run+0x84/0xb8)
[ 1946.766602] [<c0143c8c>] (task_work_run) from [<c010bdc8>] (do_work_pending+0x470/0x56c)
[ 1946.783540]  r7:5ac3c35a r6:c0d0424c r5:c200bfb0 r4:c200a000
[ 1946.793614] [<c010b958>] (do_work_pending) from [<c01000c0>] (slow_work_pending+0xc/0x20)
[ 1946.810553] Exception stack(0xc200bfb0 to 0xc200bff8)
[ 1946.820129] bfa0:                                     00000000 00000000 000000aa b5e21430
[ 1946.837104] bfc0: bef867a0 00000001 bef86840 00000034 bef86838 bef86790 bef86794 bef867a0
[ 1946.854125] bfe0: 00000000 bef86798 b67b7a1c b6d626a4 60000010 b5a23760
[ 1946.865335]  r10:00000000 r9:c200a000 r8:c0100224 r7:00000034 r6:bef86840 r5:00000001
[ 1946.881914]  r4:bef867a0
[ 1946.888793] ---[ end trace 7387f2a9725b28d0 ]---

Fixes: 5e33f6fdf7 ("usb: gadget: ffs: add eventfd notification about ffs events")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Link: https://lore.kernel.org/r/f79eeea29f3f98de6782a064ec0f7351ad2f598f.1639793920.git.plr.vincent@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 09:05:21 +01:00
Lad Prabhakar
ce1d37cb76 usb: musb: dsps: Use platform_get_irq_byname() to get the interrupt
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Lad Prabhakar
78e17d6999 usb: cdns3: Use platform_get_irq_byname() to get the interrupt
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().

Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Lad Prabhakar
d057ac484a usb: isp1760: Use platform_get_irq() to get the interrupt
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq(). Also use irq_get_trigger_type to get the
IRQ trigger flags.

Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Lad Prabhakar
74b39dfabd usb: dwc3: Drop unneeded calls to platform_get_resource_byname()
Drop unneeded calls to platform_get_resource_byname() from
dwc3_host_init(). dwc3_host_init() already calls dwc3_host_get_irq()
which gets the irq number, just use this to get the IRQ resource data
and fill the xhci_resources[1]

Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Lad Prabhakar
22ae6415c7 usb: renesas_usbhs: Use platform_get_irq() to get the interrupt
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().

Drop irqflags member from struct usbhs_priv as this driver is used by
two non DT users sh7757lcr and ecovec24 which do not pass
IORESOURCE_IRQ_SHAREABLE as part of their pdata. Along this drop the
IRQF_SHARED flag handling in the code.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Lad Prabhakar
9198e0298e usb: host: fotg210: Use platform_get_irq() to get the interrupt
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:51:57 +01:00
Changcheng Deng
f28fb27ef7 xhci: use max() to make code cleaner
Use max() in order to make code cleaner.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Link: https://lore.kernel.org/r/20211215091602.445009-1-deng.changcheng@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 08:48:24 +01:00
Wen Gong
01417e5793 ath11k: add regdb.bin download for regdb offload
The regdomain is self-managed type for ath11k, the regdomain info is
reported from firmware, it is not from wireless regdb. Firmware fetch
the regdomain info from board data file before. Currently most of the
regdomain info has moved to another file regdb.bin from board data
file for some chips such as QCA6390 and WCN6855, so the regdomain info
left in board data file is not enough to support the feature which need
more regdomain info.

After download regdb.bin, firmware will fetch the regdomain info from
regdb.bin instead of board data file and report to ath11k. If it does
not have the file regdb.bin, it also can initialize wlan success and
firmware then fetch regdomain info from board data file.

Add download the regdb.bin before download board data for some specific
chip which support supports_regdb in hardware parameters.

download regdb.bin log:
[430082.334162] ath11k_pci 0000:05:00.0: chip_id 0x2 chip_family 0xb board_id 0x106 soc_id 0x400c0200
[430082.334169] ath11k_pci 0000:05:00.0: fw_version 0x110c8b4c fw_build_timestamp 2021-10-25 07:41 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02892-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
[430082.334414] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/regdb.bin size 24310

output of "iw reg get"
global
country US: DFS-FCC
        (2402 - 2472 @ 40), (N/A, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
        (5735 - 5835 @ 80), (N/A, 30), (N/A)
        (57240 - 63720 @ 2160), (N/A, 40), (N/A)

phy#0 (self-managed)
country US: DFS-FCC
        (2402 - 2472 @ 40), (6, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 24), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 24), (0 ms), DFS, AUTO-BW
        (5735 - 5895 @ 160), (N/A, 30), (N/A), AUTO-BW
        (5945 - 7125 @ 160), (N/A, 24), (N/A), NO-OUTDOOR, AUTO-BW

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211220062355.17021-1-quic_wgong@quicinc.com
2021-12-21 09:41:00 +02:00
Greg Kroah-Hartman
4daf08a0af Revert "usb: host: ehci-sh: propagate errors from platform_get_irq()"
This reverts commit 1aebf115af as the
prerequsite commit for it is not in the tree.

Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-21 07:14:05 +01:00
Vinod Koul
27a0d0b846 arm64: dts: qcom: sm8450-qrd: Enable USB nodes
Enable the usb phy and usb controller in peripheral mode. This helps to
get the adb working with the QRD board.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211216110813.658384-2-vkoul@kernel.org
2021-12-20 23:17:44 -06:00
Vinod Koul
19fd04fb92 arm64: dts: qcom: sm8450: Add usb nodes
SM8450 features a single USB controller which connects to both HS and SS
phy. Add the USB and the phy nodes for Qualcomm SM8450 SoC.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211216110813.658384-1-vkoul@kernel.org
2021-12-20 23:17:44 -06:00
Vinod Koul
96ea2a4291 clk: qcom: turingcc-qcs404: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-9-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
737a226758 clk: qcom: q6sstop-qcs404: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-8-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
5bcc2521ec clk: qcom: mmcc-apq8084: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-7-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
3333607bdd clk: qcom: lpasscc-sdm845: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-6-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
27f239a4c5 clk: qcom: lpasscc-sc7280: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-5-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
1fc8887c04 clk: qcom: gcc-sm6350: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-4-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
d7a49c8d2c clk: qcom: gcc-msm8994: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-3-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Vinod Koul
33aa94fd94 clk: qcom: gcc-sm8350: explicitly include clk-provider.h
Per Stephen, clk providers need to include clk-provider.h, so include in
this driver as well

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211215113803.620032-2-vkoul@kernel.org
2021-12-20 23:14:50 -06:00
Jae Hyun Yoo
45cd8bbaaa ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
KCS node as one of required properties to enable the LCLK by the
LPC KCS driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20211108190200.290957-5-jae.hyun.yoo@intel.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:33:10 +10:30
Jae Hyun Yoo
002c42d37e dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC IBT driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211108190200.290957-3-jae.hyun.yoo@intel.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:32:39 +10:30
Jae Hyun Yoo
a350dc623e ARM: dts: aspeed: add LCLK setting into LPC IBT node
If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
IBT node as one of required properties to enable the LCLK by the
LPC IBT driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20211108190200.290957-2-jae.hyun.yoo@intel.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:31:57 +10:30
Eddie James
62589e873d ARM: dts: aspeed: p10: Add TPM device
Add the Nuvoton NPCT75X, a TIS I2C TPM.

Modified Eddie's change to include the general compatible string, and
combine the rainier and everest patches.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211208191758.20517-8-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:30:31 +10:30
Eddie James
1fe5c05c7c ARM: dts: aspeed: p10: Enable USB host ports
Ensure both controllers are enabled on, and add GPIO hog for USB power
control to set the USB power to always on.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211208170641.13322-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:29:43 +10:30
Ali El-Haj-Mahmoud
30daf3cd89 ARM: dts: aspeed: Add TYAN S8036 BMC machine
The TYAN S8036 is a server platform with an ASPEED AST2500 BMC.

Signed-off-by: Ali El-Haj-Mahmoud <aaelhaj@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211130180110.2217042-1-aaelhaj@google.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:15:39 +10:30
Oskar Senft
4fcbe1f5b6 ARM: dts: aspeed: tyan-s7106: Add uart_routing and fix vuart config
Configure the vuart in such a way that it does not inhibit the SuperIO's
UART from functioning correctly. This allows the same DTS to be used for
both configurations with SuperIO and VUART (depending on the BIOS
build). The decision on whether to actually enable VUART can then be
made at runtime.

This change also enables the new uart_routing driver for the SuperIO
case.

Signed-off-by: Oskar Senft <osk@google.com>
Link: https://lore.kernel.org/r/20211130184855.1779353-1-osk@google.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:09:09 +10:30
Howard Chiu
a8c729e966 ARM: dts: aspeed: Adding Facebook Bletchley BMC
Initial introduction of Facebook Bletchley equipped with
Aspeed 2600 BMC SoC.

Signed-off-by: Howard Chiu <howard.chiu@quantatw.com>
Link: https://lore.kernel.org/r/20211207094923.422422-1-howard.chiu@quantatw.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:08:15 +10:30
Lei YU
b26965e997 ARM: dts: aspeed: g220a: Enable secondary flash
Enable the secondary flash of the g220a's BMC and the wdt2.

Signed-off-by: Lei YU <yulei.sh@bytedance.com>
Link: https://lore.kernel.org/r/20211210093623.2140640-1-yulei.sh@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:02:27 +10:30
Lei YU
0720caa3f8 ARM: dts: Add openbmc-flash-layout-64-alt.dtsi
Add openbmc-flash-layout-64-alt.dtsi to describe the partitions of the
secondary flash for OpenBMC's 64M static layout.
The layout is the same as openbmc-flash-layout-64.dtsi and the labels
are prepended with "alt-" for the partitions.

Signed-off-by: Lei YU <yulei.sh@bytedance.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://lore.kernel.org/r/20211210093443.2140557-1-yulei.sh@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:02:27 +10:30
Joel Stanley
fea2894676 ARM: dts: aspeed: Add secure boot controller node
The ast2600 has a secure boot controller.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20211117035106.321454-3-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:02:27 +10:30
Joel Stanley
bc9fd597b3 dt-bindings: aspeed: Add Secure Boot Controller bindings
The secure boot controller was first introduced in the AST2600.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211117035106.321454-2-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-12-21 15:02:26 +10:30
Ming Lei
37e11c3616 block: call blk_exit_queue() before freeing q->stats
blk_stat_disable_accounting() is added in commit 68497092bd
("block: make queue stat accounting a reference"), and called in
kyber_exit_sched().

So we have to free q->stats after elevator is unloaded from
blk_exit_queue() in blk_release_queue(). Otherwise kernel panic
is caused.

Fixes: 68497092bd ("block: make queue stat accounting a reference")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20211221040436.1333880-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-12-20 21:07:51 -07:00
Jens Axboe
a957b61254 block: fix error in handling dead task for ioprio setting
Don't combine the task exiting and "already have io_context" case, we
need to just abort if the task is marked as dead. Return -ESRCH, which
is the documented value for ioprio_set() if the specified task could not
be found.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: syzbot+8836466a79f4175961b0@syzkaller.appspotmail.com
Fixes: 5fc11eebb4 ("block: open code create_task_io_context in set_task_ioprio")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-12-20 20:32:24 -07:00
Mark Brown
38fa8d3cac
ASoC: Use dev_err_probe() helper
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:

This patch-set tries to use dev_err_probe() helper function
instead of manual dev_err() code.
I hope ASoC will be more clean code by this patch-set.
2021-12-21 02:48:48 +00:00
Heiner Kallweit
ac8c58f5b5 igb: fix deadlock caused by taking RTNL in RPM resume path
Recent net core changes caused an issue with few Intel drivers
(reportedly igb), where taking RTNL in RPM resume path results in a
deadlock. See [0] for a bug report. I don't think the core changes
are wrong, but taking RTNL in RPM resume path isn't needed.
The Intel drivers are the only ones doing this. See [1] for a
discussion on the issue. Following patch changes the RPM resume path
to not take RTNL.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/

Fixes: bd869245a3 ("net: core: try to runtime-resume detached device in __dev_open")
Fixes: f32a213765 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops")
Tested-by: Martin Stolpe <martin.stolpe@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20211220201844.2714498-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:48:09 -08:00
Jeroen de Borst
1f06f7d97f gve: Correct order of processing device options
The legacy raw addressing device option was processed before the
new RDA queue format option.  This caused the supported features mask,
which is provided only on the RDA queue format option, not to be set.

This disabled jumbo-frame support when using raw adressing.

Fixes: 255489f5b3 ("gve: Add a jumbo-frame device option")
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://lore.kernel.org/r/20211220192746.2900594-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:47:56 -08:00
Willem de Bruijn
1ed1d59211 net: skip virtio_net_hdr_set_proto if protocol already set
virtio_net_hdr_set_proto infers skb->protocol from the virtio_net_hdr
gso_type, to avoid packets getting dropped for lack of a proto type.

Its protocol choice is a guess, especially in the case of UFO, where
the single VIRTIO_NET_HDR_GSO_UDP label covers both UFOv4 and UFOv6.

Skip this best effort if the field is already initialized. Whether
explicitly from userspace, or implicitly based on an earlier call to
dev_parse_header_protocol (which is more robust, but was introduced
after this patch).

Fixes: 9d2f67e43b ("net/packet: fix packet drop as of virtio gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220145027.2784293-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:47:37 -08:00
Willem de Bruijn
7e5cced9ca net: accept UFOv6 packages in virtio_net_hdr_to_skb
Skb with skb->protocol 0 at the time of virtio_net_hdr_to_skb may have
a protocol inferred from virtio_net_hdr with virtio_net_hdr_set_proto.

Unlike TCP, UDP does not have separate types for IPv4 and IPv6. Type
VIRTIO_NET_HDR_GSO_UDP is guessed to be IPv4/UDP. As of the below
commit, UFOv6 packets are dropped due to not matching the protocol as
obtained from dev_parse_header_protocol.

Invert the test to take that L2 protocol field as starting point and
pass both UFOv4 and UFOv6 for VIRTIO_NET_HDR_GSO_UDP.

Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Link: https://lore.kernel.org/netdev/CABcq3pG9GRCYqFDBAJ48H1vpnnX=41u+MhQnayF1ztLH4WX0Fw@mail.gmail.com/
Reported-by: Andrew Melnichenko <andrew@daynix.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220144901.2784030-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:47:27 -08:00
Willem de Bruijn
a9725e1d39 docs: networking: replace skb_hwtstamp_tx with skb_tstamp_tx
Tiny doc fix. The hardware transmit function was called skb_tstamp_tx
from its introduction in commit ac45f602ee ("net: infrastructure for
hardware time stamping") in the same series as this documentation.

Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220144608.2783526-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:47:11 -08:00
Eric Dumazet
8f905c0e73 inet: fully convert sk->sk_rx_dst to RCU rules
syzbot reported various issues around early demux,
one being included in this changelog [1]

sk->sk_rx_dst is using RCU protection without clearly
documenting it.

And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv()
are not following standard RCU rules.

[a]    dst_release(dst);
[b]    sk->sk_rx_dst = NULL;

They look wrong because a delete operation of RCU protected
pointer is supposed to clear the pointer before
the call_rcu()/synchronize_rcu() guarding actual memory freeing.

In some cases indeed, dst could be freed before [b] is done.

We could cheat by clearing sk_rx_dst before calling
dst_release(), but this seems the right time to stick
to standard RCU annotations and debugging facilities.

[1]
BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline]
BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204

CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
 __kasan_report mm/kasan/report.c:433 [inline]
 kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
 dst_check include/net/dst.h:470 [inline]
 tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
 ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340
 ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583
 ip_sublist_rcv net/ipv4/ip_input.c:609 [inline]
 ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644
 __netif_receive_skb_list_ptype net/core/dev.c:5508 [inline]
 __netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556
 __netif_receive_skb_list net/core/dev.c:5608 [inline]
 netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699
 gro_normal_list net/core/dev.c:5853 [inline]
 gro_normal_list net/core/dev.c:5849 [inline]
 napi_complete_done+0x1f1/0x880 net/core/dev.c:6590
 virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline]
 virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557
 __napi_poll+0xaf/0x440 net/core/dev.c:7023
 napi_poll net/core/dev.c:7090 [inline]
 net_rx_action+0x801/0xb40 net/core/dev.c:7177
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558
 invoke_softirq kernel/softirq.c:432 [inline]
 __irq_exit_rcu+0x123/0x180 kernel/softirq.c:637
 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649
 common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240
 asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629
RIP: 0033:0x7f5e972bfd57
Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73
RSP: 002b:00007fff8a413210 EFLAGS: 00000283
RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45
RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45
RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9
R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0
R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019
 </TASK>

Allocated by task 13:
 kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
 kasan_set_track mm/kasan/common.c:46 [inline]
 set_alloc_info mm/kasan/common.c:434 [inline]
 __kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467
 kasan_slab_alloc include/linux/kasan.h:259 [inline]
 slab_post_alloc_hook mm/slab.h:519 [inline]
 slab_alloc_node mm/slub.c:3234 [inline]
 slab_alloc mm/slub.c:3242 [inline]
 kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247
 dst_alloc+0x146/0x1f0 net/core/dst.c:92
 rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613
 ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:2340
 ip_route_input_rcu net/ipv4/route.c:2470 [inline]
 ip_route_input_noref+0x116/0x2a0 net/ipv4/route.c:2415
 ip_rcv_finish_core.constprop.0+0x288/0x1e80 net/ipv4/ip_input.c:354
 ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583
 ip_sublist_rcv net/ipv4/ip_input.c:609 [inline]
 ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644
 __netif_receive_skb_list_ptype net/core/dev.c:5508 [inline]
 __netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556
 __netif_receive_skb_list net/core/dev.c:5608 [inline]
 netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699
 gro_normal_list net/core/dev.c:5853 [inline]
 gro_normal_list net/core/dev.c:5849 [inline]
 napi_complete_done+0x1f1/0x880 net/core/dev.c:6590
 virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline]
 virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557
 __napi_poll+0xaf/0x440 net/core/dev.c:7023
 napi_poll net/core/dev.c:7090 [inline]
 net_rx_action+0x801/0xb40 net/core/dev.c:7177
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558

Freed by task 13:
 kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
 kasan_set_track+0x21/0x30 mm/kasan/common.c:46
 kasan_set_free_info+0x20/0x30 mm/kasan/generic.c:370
 ____kasan_slab_free mm/kasan/common.c:366 [inline]
 ____kasan_slab_free mm/kasan/common.c:328 [inline]
 __kasan_slab_free+0xff/0x130 mm/kasan/common.c:374
 kasan_slab_free include/linux/kasan.h:235 [inline]
 slab_free_hook mm/slub.c:1723 [inline]
 slab_free_freelist_hook+0x8b/0x1c0 mm/slub.c:1749
 slab_free mm/slub.c:3513 [inline]
 kmem_cache_free+0xbd/0x5d0 mm/slub.c:3530
 dst_destroy+0x2d6/0x3f0 net/core/dst.c:127
 rcu_do_batch kernel/rcu/tree.c:2506 [inline]
 rcu_core+0x7ab/0x1470 kernel/rcu/tree.c:2741
 __do_softirq+0x29b/0x9c2 kernel/softirq.c:558

Last potentially related work creation:
 kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
 __kasan_record_aux_stack+0xf5/0x120 mm/kasan/generic.c:348
 __call_rcu kernel/rcu/tree.c:2985 [inline]
 call_rcu+0xb1/0x740 kernel/rcu/tree.c:3065
 dst_release net/core/dst.c:177 [inline]
 dst_release+0x79/0xe0 net/core/dst.c:167
 tcp_v4_do_rcv+0x612/0x8d0 net/ipv4/tcp_ipv4.c:1712
 sk_backlog_rcv include/net/sock.h:1030 [inline]
 __release_sock+0x134/0x3b0 net/core/sock.c:2768
 release_sock+0x54/0x1b0 net/core/sock.c:3300
 tcp_sendmsg+0x36/0x40 net/ipv4/tcp.c:1441
 inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:724
 sock_write_iter+0x289/0x3c0 net/socket.c:1057
 call_write_iter include/linux/fs.h:2162 [inline]
 new_sync_write+0x429/0x660 fs/read_write.c:503
 vfs_write+0x7cd/0xae0 fs/read_write.c:590
 ksys_write+0x1ee/0x250 fs/read_write.c:643
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

The buggy address belongs to the object at ffff88807f1cb700
 which belongs to the cache ip_dst_cache of size 176
The buggy address is located 58 bytes inside of
 176-byte region [ffff88807f1cb700, ffff88807f1cb7b0)
The buggy address belongs to the page:
page:ffffea0001fc72c0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x7f1cb
flags: 0xfff00000000200(slab|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000000200 dead000000000100 dead000000000122 ffff8881413bb780
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x112a20(GFP_ATOMIC|__GFP_NOWARN|__GFP_NORETRY|__GFP_HARDWALL), pid 5, ts 108466983062, free_ts 108048976062
 prep_new_page mm/page_alloc.c:2418 [inline]
 get_page_from_freelist+0xa72/0x2f50 mm/page_alloc.c:4149
 __alloc_pages+0x1b2/0x500 mm/page_alloc.c:5369
 alloc_pages+0x1a7/0x300 mm/mempolicy.c:2191
 alloc_slab_page mm/slub.c:1793 [inline]
 allocate_slab mm/slub.c:1930 [inline]
 new_slab+0x32d/0x4a0 mm/slub.c:1993
 ___slab_alloc+0x918/0xfe0 mm/slub.c:3022
 __slab_alloc.constprop.0+0x4d/0xa0 mm/slub.c:3109
 slab_alloc_node mm/slub.c:3200 [inline]
 slab_alloc mm/slub.c:3242 [inline]
 kmem_cache_alloc+0x35c/0x3a0 mm/slub.c:3247
 dst_alloc+0x146/0x1f0 net/core/dst.c:92
 rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613
 __mkroute_output net/ipv4/route.c:2564 [inline]
 ip_route_output_key_hash_rcu+0x921/0x2d00 net/ipv4/route.c:2791
 ip_route_output_key_hash+0x18b/0x300 net/ipv4/route.c:2619
 __ip_route_output_key include/net/route.h:126 [inline]
 ip_route_output_flow+0x23/0x150 net/ipv4/route.c:2850
 ip_route_output_key include/net/route.h:142 [inline]
 geneve_get_v4_rt+0x3a6/0x830 drivers/net/geneve.c:809
 geneve_xmit_skb drivers/net/geneve.c:899 [inline]
 geneve_xmit+0xc4a/0x3540 drivers/net/geneve.c:1082
 __netdev_start_xmit include/linux/netdevice.h:4994 [inline]
 netdev_start_xmit include/linux/netdevice.h:5008 [inline]
 xmit_one net/core/dev.c:3590 [inline]
 dev_hard_start_xmit+0x1eb/0x920 net/core/dev.c:3606
 __dev_queue_xmit+0x299a/0x3650 net/core/dev.c:4229
page last free stack trace:
 reset_page_owner include/linux/page_owner.h:24 [inline]
 free_pages_prepare mm/page_alloc.c:1338 [inline]
 free_pcp_prepare+0x374/0x870 mm/page_alloc.c:1389
 free_unref_page_prepare mm/page_alloc.c:3309 [inline]
 free_unref_page+0x19/0x690 mm/page_alloc.c:3388
 qlink_free mm/kasan/quarantine.c:146 [inline]
 qlist_free_all+0x5a/0xc0 mm/kasan/quarantine.c:165
 kasan_quarantine_reduce+0x180/0x200 mm/kasan/quarantine.c:272
 __kasan_slab_alloc+0xa2/0xc0 mm/kasan/common.c:444
 kasan_slab_alloc include/linux/kasan.h:259 [inline]
 slab_post_alloc_hook mm/slab.h:519 [inline]
 slab_alloc_node mm/slub.c:3234 [inline]
 kmem_cache_alloc_node+0x255/0x3f0 mm/slub.c:3270
 __alloc_skb+0x215/0x340 net/core/skbuff.c:414
 alloc_skb include/linux/skbuff.h:1126 [inline]
 alloc_skb_with_frags+0x93/0x620 net/core/skbuff.c:6078
 sock_alloc_send_pskb+0x783/0x910 net/core/sock.c:2575
 mld_newpack+0x1df/0x770 net/ipv6/mcast.c:1754
 add_grhead+0x265/0x330 net/ipv6/mcast.c:1857
 add_grec+0x1053/0x14e0 net/ipv6/mcast.c:1995
 mld_send_initial_cr.part.0+0xf6/0x230 net/ipv6/mcast.c:2242
 mld_send_initial_cr net/ipv6/mcast.c:1232 [inline]
 mld_dad_work+0x1d3/0x690 net/ipv6/mcast.c:2268
 process_one_work+0x9b2/0x1690 kernel/workqueue.c:2298
 worker_thread+0x658/0x11f0 kernel/workqueue.c:2445

Memory state around the buggy address:
 ffff88807f1cb600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff88807f1cb680: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc
>ffff88807f1cb700: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                        ^
 ffff88807f1cb780: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc
 ffff88807f1cb800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 41063e9dd1 ("ipv4: Early TCP socket demux.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211220143330.680945-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:46:43 -08:00
Jakub Kicinski
f7a5319b44 Merge branch 'net-amd-xgbe-add-support-for-yellow-carp-ethernet-device'
Raju Rangoju says:

====================
net: amd-xgbe: Add support for Yellow Carp Ethernet device

Add support for newer version of Hardware, the Yellow Carp Ethernet device
====================

Link: https://lore.kernel.org/r/20211220135428.1123575-1-rrangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20 18:42:44 -08:00