Audio control requests that set sampling frequency sometimes fail on
this card. Adding delay between control messages eliminates that problem.
usb 1-1: New USB device found, idVendor=0666, idProduct=0880
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB Audio
usb 1-1: Manufacturer: SPACETOUCH
usb 1-1: SerialNumber: 000000000
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/TYUPR06MB6217D93F595D9995413C9721D2A72@TYUPR06MB6217.apcprd06.prod.outlook.com
On the Audient iD14 (2708:0008), feature unit 12 is traced through to
the Speaker output terminal and is therefore exported as "Speaker
Playback Volume". The name fits it badly. It advertises Volume on
only four of its six logical channels, which the driver records as
cmask=0xf, channels=4 on a 6-channel playback stream, and it sits on
the monitor mixer branch rather than in the direct playback path:
INPUT_TERMINAL 2 (USB streaming, 6ch) -> EXTENSION_UNIT 51 ->
FEATURE_UNIT 10 (no controls) -> OUTPUT_TERMINAL 20 (Speaker)
while FU 12 hangs off MIXER_UNIT 60 and feeds back into
EXTENSION_UNIT 51.
Userspace adopts the control as the stream's hardware playback volume,
so any setting below 0 dB attenuates part of the stream and not the
rest. Measured over the device's own digital loopback, with one
-12 dBFS tone per channel played straight to hw:, PCM channel 0 is
unaffected while channel 1 tracks the control: at 107/127 (-20 dB) the
two read -15.89 and -35.89 dBFS, a 20.00 dB imbalance, and at 127/127
both read -15.89 dBFS.
Give the unit a non-standard name so that it is no longer taken for
the stream's master volume. Dropping the control instead also fixes
the imbalance, but FU 12 keeps its value across a module reload, so
dropping it strands a device that is already attenuated with nothing
able to reset it. Renaming leaves the monitor gain reachable and that
recovery path intact.
The mapped name ends in "Playback" because a name from the map
suppresses the automatic " Playback" but still gets " Volume"
appended; the control comes out as "Monitor Mix Playback Volume".
Tested on the ACP path with PipeWire, which is where the problem
reproduces: the control now stays at 127 at every volume setting and
the imbalance is 0.00 dB, and setting it by hand to 107 and back to
127 gives 20.00 dB and 0.00 dB as before.
Link: https://lore.kernel.org/linux-sound/0102019fed22f9d3-fa294ec5-02f1-4fd3-b3fa-76efc14331cc-000000@eu-west-1.amazonses.com/T/#u
Signed-off-by: Neil Andrews <neil@androos.io>
Link: https://patch.msgid.link/0102019ffcdbb1e6-9b59d3cc-ef05-4df1-8f9f-fb2f425bcda2-000000@eu-west-1.amazonses.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fixed audio formats for the PreSonus AudioBox USB specify a discrete
rate mask but leave nr_rates at zero and rate_table unset. find_format()
therefore rejects every requested rate, preventing the playback and
capture streams from being opened.
Add the advertised 44100 and 48000 Hz rates to both streams and report
their 24 significant bits.
Fixes: 34fe4a9df2 ("ALSA: usb-audio: Add quirk for PreSonus AudioBox USB")
Cc: stable@vger.kernel.org
Signed-off-by: Trevor Vorhees <vorhees-work@proton.me>
Link: https://patch.msgid.link/20260811-audiobox-usb-fix-v1-1-13c8b7f071ea@proton.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is managed by USB core and drivers aren't expected to touch it.
It should only be not NULL on a submitted URB, in which case clearing
defeats the "submitted while active" sanity check in usb_submit_urb()
and may crash the HCD handling the URB and panic the kernel.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260810075728.483c827e.michal.pecio@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scarlett2_init_notify() used mixer->urb, which
snd_usb_mixer_status_create() allocates for the UAC2 status interrupt
endpoint and mixer.c manages. On a device with that endpoint, the
"already in use" check fires on the status URB and returns 0 for
success without doing anything. No notification URB is submitted, and
cmd_done is left zeroed because it is initialised past that check and
nowhere else. scarlett2_usb_init() then issues SCARLETT2_USB_INIT_1
and wait_for_completion_timeout() would crash adding to the zeroed
wait.head.
Use a separate URB in scarlett2_data, as done for FCP, and initialise
cmd_done in scarlett2_init_private(). mixer.c was also freeing the URB
in snd_usb_mixer_free() and resubmitting it in
snd_usb_mixer_activate(), so scarlett2 must now do both: add
scarlett2_cleanup_urb(), called from private_free and private_suspend,
and a private_resume callback to re-establish the URB after resume.
scarlett2_init_notify() is reached from there, and the URB kill path
in scarlett2_notify() completes cmd_done, leaving a stale count that
would satisfy the next command's wait before the device ACKs. Use
reinit_completion() to clear it.
Also free the URB if the transfer buffer allocation fails, and both if
usb_submit_urb() fails. Move scarlett2_init_notify() up next to
scarlett2_cleanup_urb() so scarlett2_init_private() can reference it
without a forward declaration.
Fixes: 1b65088958 ("ALSA: scarlett2: Implement handling of the ACK notification")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-5
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/ffb8ba37d5d605dfdfd8576949d67098651f9349.1786290885.git.g@b4.vu
fcp_init_notify() used mixer->urb, which snd_usb_mixer_status_create()
allocates for the optional UAC2 status interrupt endpoint and mixer.c
kills, resubmits and frees. On a device with that endpoint,
fcp_init_notify()'s "already set up" early return fires on the status
URB and returns success without doing anything. No FCP notification
URB is submitted, and cmd_done is left zeroed because it is
initialised past that early return and nowhere else. fcp_init() then
issues init1_opcode and wait_for_completion_timeout() would crash
adding to the zeroed wait.head. fcp_cleanup_urb() would also kill and
free mixer.c's status URB.
Use a separate URB in fcp_data, and initialise cmd_done in
fcp_init_private() where fcp_data is allocated. fcp_init_notify() is
reached again after suspend via fcp_reinit(), and the URB kill path in
fcp_notify() completes cmd_done, leaving a stale count that would
satisfy the next command's wait before the device ACKs. Use
reinit_completion() to clear it.
Fixes: 46757a3e7d ("ALSA: FCP: Add Focusrite Control Protocol driver")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-5
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/2cad281e6434024ca48a9ecc94fa19d6777e9be7.1786290885.git.g@b4.vu
set_sample_rate_v2v3() returns early when the clock already reports the
requested rate:
prev_rate = get_sample_rate_v2v3(chip, fmt->iface,
fmt->altsetting, clock);
if (prev_rate == rate)
goto validation;
A device advertising exactly one sample rate always takes this branch, so
it never receives a SET_CUR for CS_SAM_FREQ_CONTROL at all.
The Mackie DLZ Creator XS (0a73:003a, 14 in / 4 out, 48 kHz only) requires
that write. Without it the device drops off the USB bus roughly 0.2-1.8 s
into any stream, clearing its port CONNECTION bit; captured audio is
byte-correct until the instant it vanishes.
USBPcap traces of a cold-booted device on Windows show SET_CUR 48000 issued
unconditionally on every stream start, followed by clean streaming. The
device is otherwise driven with plain class-compliant UAC2 - it also works
on iOS, which cannot load a vendor driver - so no vendor-specific
initialization is involved.
The device is self-powered, so the resulting state survives a USB replug:
initializing it on any host that issues the write leaves it working on
Linux until it is power-cycled, which made the failure look intermittent.
Add a quirk flag rather than dropping the early exit, since the opposite
requirement also exists in-tree: QUIRK_FLAG_FIXED_RATE suppresses rate
setting for single-rate devices (JBL Quantum610/810). The two behaviors
are device-dependent and cannot both be the default.
A/B on identically cold-booted hardware, same kernel, same port, repeated
twice:
without the flag device dropped after 5-6 s, then again after 3-4 s
with the flag 20 s playback followed by 20 s of 14-channel capture,
960000 frames, zero re-enumerations
This change was developed with an AI coding assistant. The assistant did
the trace analysis that located the bug and wrote the patch and this
changelog; the hardware testing, the cold-boot cycles and the decision to
submit were the author's. Several earlier hypotheses it proposed - URB
queue depth, isochronous packet under-allocation, endpoint start ordering -
were disproven by measurement before this one.
The bug was located with usbmon on Linux and USBPcap on Windows, by
diffing an enumeration capture of a cold-booted device on each host.
Verified on physical hardware by the A/B above.
Assisted-by: Claude-Code:claude-opus-5
Signed-off-by: JJ Macalinao <jj@macalinao.org>
Link: https://patch.msgid.link/20260808172726.1107550-1-jj@macalinao.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent "sticky mixer" sanity check in USB-audio driver caused a
regression on SteelSeries Arctis Nova 5 (1038:2232); because the
firmware doesn't handle GET_CUR requests, some mixers are effectively
disabled, leading to the too low / soft volumes:
usb 5-1.1: 9:0: sticky mixer values (-19712/0/256 => 0), disabling
usb 5-1.1: 10:0: sticky mixer values (-21248/0/256 => 0), disabling
Restore the functionality by ignoring GET_CUR errors intentionally
with MIXER_GET_CUR_BROKEN quirk.
Fixes: 86aa1ea1f1 ("ALSA: usb-audio: Do not expose sticky mixers")
Reported-by: Gert Burger <gertburger@gmail.com>
Closes: https://lore.kernel.org/CAEQ1D3kdA3mkQx7ei9Kq0gwky0qroJqCLKrkvgfkqgTbeu086A@mail.gmail.com
Link: https://bbs.archlinux.org/viewtopic.php?id=314220
Link: https://patch.msgid.link/20260808152258.1948767-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for sticky mixer volumes caused regressions of M-audio
Fast Track Ultra device, where the mixer state is kept to the default
value.
Add the quirk entries to tolerate the broken mixer behavior. As the
device is known to work in the implicit feedback mode, explicitly
enable the implicit feedback mode, too.
Since there are two FTU models that are almost identical, both entries
are added in this patch (0763:2080 and 0763:2081).
Fixes: 86aa1ea1f1 ("ALSA: usb-audio: Do not expose sticky mixers")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1273166
Link: https://patch.msgid.link/20260807083418.1712585-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fcp_ioctl_init() allocates its response buffer with kmalloc() and copies
the whole buffer back to userspace:
buf_size = init.step0_resp_size + init.step2_resp_size;
void *resp __free(kfree) =
kmalloc(buf_size, GFP_KERNEL);
...
if (copy_to_user(arg->resp, resp, buf_size))
return -EFAULT;
Nothing clears the buffer, and the only writer of its leading
step0_resp_size bytes is the step-0 control transfer:
err = snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0),
FCP_USB_REQ_STEP0,
USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_IN,
0, private->bInterfaceNumber,
step0_resp, private->step0_resp_size);
if (err < 0)
return err;
usb_fill_control_urb() does not set URB_SHORT_NOT_OK, so a short or
zero-length data stage completes with status 0 and snd_usb_ctl_msg()
returns a small actual_length. The only check is err < 0, so a short
transfer is accepted as success.
snd_usb_ctl_msg() copies the full size back unconditionally:
buf = kmemdup(data, size, GFP_KERNEL);
...
memcpy(data, buf, size);
Bytes the device never wrote are therefore restored into resp unchanged
and copied to userspace. step0_resp_size and step2_resp_size are each
validated only to 1..255, so the caller also picks the slab cache, from
kmalloc-8 up to kmalloc-512.
On 7.2.0-rc5 (arm64), device answering step 0 with a zero-length data
stage, s0 = s2 = 255:
# init_on_alloc off, no spray
step0 window [0,255): nonzero=94/255
000: 00 80 60 06 00 00 ff ff 18 00 00 00 57 01 ea 01
010: 08 78 22 13 00 00 ff ff a8 c4 5f 80 00 80 ff ff
# same kernel, kmalloc-512 pre-seeded with an 8-byte tag
step0 window [0,255): nonzero=219/255 tagbytes=232
# identical run, init_on_alloc=1
step0 window [0,255): nonzero=0/255 tagbytes=0
# all three runs
step2 window [255,510): device words matched=62/62
a8 c4 5f 80 00 80 ff ff is the little-endian kernel text address
ffff8000805fc4a8. The step-2 window is unaffected, so the disclosure is
exactly the step-0 region.
Zero the buffer, and require the step-0 transfer to deliver the full
step0_resp_size bytes so a short data stage is reported as an error.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 46757a3e7d ("ALSA: FCP: Add Focusrite Control Protocol driver")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260805013804.38839-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_us428ctls_vm_fault() turns the faulting page offset into a kernel
address with no bound of any kind:
offset = vmf->pgoff << PAGE_SHIFT;
vaddr = (char *)(...)->us428ctls_sharedmem + offset;
page = virt_to_page(vaddr);
get_page(page);
vmf->page = page;
return 0;
snd_us428ctls_mmap() checks only the length of the mapping, never the
offset, and us428ctls_sharedmem is a single page from
alloc_pages_exact(). For a character device file_mmap_size_max()
returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page
offset above zero resolves to a struct page outside the object, and the
handler installs it into the caller's address space read-write; the vma
is not marked read-only.
The caller picks the page frame with a single mmap() argument and gets
read-write access to a page of kernel memory it does not own; an offset
that lands in an unpopulated vmemmap region oopses instead.
A process that can open the hwdep node of an attached US-X2Y reaches
this after loading the FPGA image through the same node; no capability
check is involved.
On 7.2.0-rc5 (arm64), mmap() with a large offset:
Unable to handle kernel paging request at virtual address fffffdffc45d5ac8
pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
Call trace:
snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
__do_fault
__handle_mm_fault
handle_mm_fault
el0_da
Reject any offset outside the shared region. The pcm hwdep handler in
usx2yhwdeppcm.c computes its address the same way and needs the same
bound.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260805013445.38283-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
data_ep_set_params() sizes each URB transfer buffer before it adds the
Format Type II transfer delimiter:
u->packets = urb_packs;
u->buffer_size = maxsize * u->packets;
if (fmt->fmt_type == UAC_FORMAT_TYPE_II)
u->packets++; /* for transfer delimiter */
u->urb = usb_alloc_urb(u->packets, GFP_KERNEL);
buffer_size is computed from the pre-increment packet count and never
recomputed, so for a Type II endpoint the buffer is one packet short of
the packet count the URB is built with.
prepare_inbound_urb() then lays out one iso frame per packet and never
consults buffer_size:
offs = 0;
for (i = 0; i < urb_ctx->packets; i++) {
urb->iso_frame_desc[i].offset = offs;
urb->iso_frame_desc[i].length = ep->curpacksize;
offs += ep->curpacksize;
}
urb->transfer_buffer_length = offs;
urb->number_of_packets = urb_ctx->packets;
The last descriptor therefore points one packet past the end of the
transfer buffer, where the host controller writes device data on every
inbound transfer. prepare_silent_urb() and prepare_playback_urb() bound
their fill loops by ctx->buffer_size, so only capture is affected.
fmt_type comes from the device's audio streaming descriptors, so any
device advertising a Type II capture format hits this once userspace sets
hw_params on the stream.
KASAN on 7.2.0-rc5 (arm64) with a dummy_hcd/raw-gadget device, one report
per inbound transfer:
BUG: KASAN: slab-out-of-bounds in dummy_timer
Write of size 64 at addr ffff0000186171c0 by task cons02/166
__asan_memcpy
dummy_timer
hrtimer_run_softirq
Allocated by task 166:
usb_alloc_coherent
snd_usb_endpoint_set_params
The buggy address is located 0 bytes to the right of
allocated 64-byte region [ffff000018617180, ffff0000186171c0)
Compute buffer_size after the delimiter packet has been accounted for,
and bound the fill loop by buffer_size, as prepare_silent_urb() already
does on the outbound side. This grows every Type II URB allocation by
one maxsize packet.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 8fdff6a319 ("ALSA: snd-usb: implement new endpoint streaming model")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260805013441.38245-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
bcd2000_free_usb_related_resources() frees both URBs and leaves the
pointers behind:
usb_kill_urb(bcd2k->midi_out_urb);
usb_kill_urb(bcd2k->midi_in_urb);
usb_free_urb(bcd2k->midi_out_urb);
usb_free_urb(bcd2k->midi_in_urb);
The rawmidi device outlives that call. A substream that is still open
when the device is unplugged reaches bcd2000_midi_send() from the
trigger path on close. That function writes to the freed URB and then
hands it to the USB core:
bcd2k->midi_out_urb->transfer_buffer_length = BUFSIZE;
...
ret = usb_submit_urb(bcd2k->midi_out_urb, GFP_ATOMIC);
usb_kill_urb() does not stop a later submission either, so a submit that
races the disconnect can requeue the URB after it has been reaped.
midi_in_urb is exposed the same way: bcd2000_input_complete() resubmits
it from the completion handler.
KASAN on 7.2.0-rc5 (arm64):
BUG: KASAN: slab-use-after-free in bcd2000_midi_send [snd_bcd2000]
Write of size 4 at addr ffff00001827d388 by task bpoc/168
__asan_store4
bcd2000_midi_send [snd_bcd2000]
bcd2000_midi_output_trigger [snd_bcd2000]
snd_rawmidi_kernel_write1
close_substream.part.0
Freed by task 168:
usb_free_urb
bcd2000_disconnect [snd_bcd2000]
BUG: KASAN: slab-use-after-free in usb_submit_urb
Read of size 8 at addr ffff00001827d3b8 by task bpoc/168
Clear both pointers after freeing and test them on the paths that can
still run. Poison the URBs before freeing them: usb_poison_urb() waits
for a running completion handler and rejects any later submission, so
after it returns the input path is quiesced and only the rawmidi trigger
path can still reach bcd2000_midi_send(). No unpoison is needed; the
URBs are freed on the next line.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: b47a22290d ("ALSA: MIDI driver for Behringer BCD2000 USB device")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260805013428.38204-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb6fire_comm_receiver_handler() forwards a MIDI event using a length
byte the device supplies, with no bound and no check that the transfer
delivered that many bytes:
if (!urb->status) {
if (rt->receiver_buffer[0] == 0x10) /* midi in event */
if (midi_rt)
midi_rt->in_received(midi_rt,
rt->receiver_buffer + 2,
rt->receiver_buffer[1]);
}
receiver_buffer is a 64-byte kzalloc() buffer (COMM_RECEIVER_BUFSIZE), so
only 62 bytes follow the two-byte header. receiver_buffer[1] is a u8 the
device chooses, so a device that answers with 0x10 and a length of 0xFF
makes snd_rawmidi_receive() read 255 bytes starting two bytes into a
64-byte object. The bytes past the buffer are handed to userspace
through the rawmidi read path.
urb->actual_length is not consulted either, so a short transfer leaves
both the type byte and the length byte at their previous values and the
handler acts on stale data.
The receiver URB is submitted from usb6fire_comm_init() at probe, so the
read happens on plug with no user action; forwarding to userspace also
needs a MIDI input substream open, since usb6fire_midi_in_received()
only calls snd_rawmidi_receive() when rt->in is set.
KASAN on 7.2.0-rc5 (arm64), single packet from an emulated device:
BUG: KASAN: slab-out-of-bounds in snd_rawmidi_receive
Read of size 255 at addr ffff000009f64682 by task bash/183
__asan_memcpy
snd_rawmidi_receive
usb6fire_midi_in_received [snd_usb_6fire]
usb6fire_comm_receiver_handler [snd_usb_6fire]
Allocated by task 11:
usb6fire_comm_init [snd_usb_6fire]
usb6fire_chip_probe [snd_usb_6fire]
The buggy address is located 2 bytes inside of
allocated 64-byte region [ffff000009f64680, ffff000009f646c0)
Reject the event when the length exceeds the bytes that follow the
header, and require the transfer to have delivered the header plus that
many bytes. The receiver URB is submitted with a 64-byte
transfer_buffer_length, so a genuine device cannot deliver an event
longer than those 62 bytes and nothing valid is dropped.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: c6d43ba816 ("ALSA: usb/6fire - Driver for TerraTec DMX 6Fire USB")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260805013423.38175-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
capture_urb_complete() resubmits each capture URB without anchoring it:
usb_get_urb(urb);
ret = usb_submit_urb(urb, GFP_ATOMIC);
Anchoring is a property of a submission, not of the URB. The giveback
path calls usb_unanchor_urb() before urb->complete(), so an URB
resubmitted from its own completion handler is off the anchor. The
capture URBs are anchored once, at stream start, so from the first
completion onward tascam->capture_anchor is empty.
tascam_free_urbs(), tascam_disconnect(), tascam_suspend() and the
stop-work path all call usb_kill_anchored_urbs(&tascam->capture_anchor)
to reap the capture URBs before anything is freed. With the anchor empty
those calls return immediately and the URBs stay queued on the host
controller.
tascam_free_urbs() then returns the capture transfer buffers with
usb_free_coherent(), and snd_card_free() releases the snd_card
allocation that embeds tascam (card->private_data). The controller
completes the queued URBs afterwards, writing device-supplied data into
the freed transfer buffer, and capture_urb_complete() dereferences the
freed driver object.
KASAN on 7.2.0-rc5 (arm64):
BUG: KASAN: slab-use-after-free in dummy_timer
Write of size 512 at addr ffff000015b62000
__asan_memcpy
dummy_timer
hrtimer_run_softirq
Allocated by task 64:
usb_alloc_coherent
tascam_alloc_urbs
tascam_probe
Freed by task 170:
usb_free_coherent
tascam_free_urbs
tascam_disconnect
usb_unbind_interface
BUG: KASAN: slab-use-after-free in capture_urb_complete
Read of size 4 at addr ffff0000170ee878
Freed by task 170:
release_card_device
snd_card_free
tascam_disconnect
Restore the usb_anchor_urb() between the reference count bump and the
resubmission. That also makes the handler's usb_unanchor_urb() failure
arm meaningful again and restores usb_kill_anchored_urbs() as a barrier
on the disconnect, suspend and stop-work paths.
The anchoring was removed on the premise that the URB is already anchored
from the initial submission, which does not hold once the first giveback
has run.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 5cff1529a2 ("ALSA: us144mkii: capture_urb_complete: redundant usb_anchor_urb corrupts anchor list on each resubmission")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260804123625.91769-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fcp_ioctl_set_meter_map() bounds the user-supplied Level Meter map size
by the driver's own limit of 255
if (map.map_size < 1 || map.map_size > 255 ||
map.meter_slots < 1 || map.meter_slots > 255)
return -EINVAL;
and passes it to fcp_add_new_ctl() as the control's channel count, where
it is stored as elem->channels.
Every control read writes into struct snd_ctl_elem_value, whose integer
array is declared long value[128], so the limit is 128, not 255.
fcp_meter_ctl_get() stores one 64-bit word per channel into that array
with no bound of its own:
for (i = 0; i < elem->channels; i++) {
int idx = private->meter_level_map[i];
int value = idx < 0 ? 0 : le32_to_cpu(resp[idx]);
ucontrol->value.integer.value[i] = value;
}
snd_ctl_elem_read_user() serves that object from
memdup_user(_control, sizeof(*control)), 1224 bytes on LP64 out of
kmalloc-2048. offsetof(struct snd_ctl_elem_value, value) is 72, so
element i is written at byte 72 + 8 * i and element 144 already lands
past the allocation. At map_size 255 the last store ends at byte 2112,
888 bytes past the object and 64 bytes into the adjacent slab object.
The stored words come from the device and meter_level_map[] selects
which word lands in which slot, so extent and contents are both
controlled.
The core does not catch this. snd_ctl_check_elem_info() is reached only
from __snd_ctl_elem_info(), which snd_ctl_elem_read() calls under
CONFIG_SND_CTL_DEBUG; without that option snd_ctl_skip_validation() is a
compile-time true. __snd_ctl_add_replace() validates kcontrol->count and
never inspects elem->channels.
Installing an oversized map needs CAP_SYS_RAWIO, but the control outlives
the hwdep descriptor that created it, so the out-of-bounds stores are
issued by any process able to read controls on /dev/snd/controlC0.
KASAN on 7.2.0-rc5 (arm64), triggered by an unprivileged control read:
BUG: KASAN: slab-out-of-bounds in fcp_meter_ctl_get
Write of size 8 at addr ffff000017af04c8 by task fcp_trigger/185
__asan_store8
fcp_meter_ctl_get
snd_ctl_elem_read
snd_ctl_ioctl
Allocated by task 185:
memdup_user
snd_ctl_ioctl
The buggy address is located 0 bytes to the right of
allocated 1224-byte region [ffff000017af0000, ffff000017af04c8)
Bound the map size by the ABI limit rather than by 255, and bound the
store loop at the sink so it cannot run past the value array whatever
elem->channels holds.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 46757a3e7d ("ALSA: FCP: Add Focusrite Control Protocol driver")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260804123611.91715-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC mixer of the Logitech PRO X 2 LIGHTSPEED has broken mixer
GET_CUR behavior but otherwise works fine.
Add a quirk table entry matching VID/PID=0x046d/0x0af7 and apply the
MIXER_GET_CUR_BROKEN quirk flag to make the mixer usable again.
Quirky device sample (after applying the quirk flag):
usb 3-2.1: New USB device found, idVendor=046d, idProduct=0af7, bcdDevice= 1.00
usb 3-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-2.1: Product: PRO X 2 LIGHTSPEED
usb 3-2.1: Manufacturer: Logitech
usb 3-2.1: SerialNumber: 0000000000000000
usb 3-2.1: 2:0: broken mixer GET_CUR (-18944/0/256 => -2662)
usb 3-2.1: 6:0: broken mixer GET_CUR (-18944/0/256 => 0)
Fixes: 86aa1ea1f1 ("ALSA: usb-audio: Do not expose sticky mixers")
Suggested-by: Brian van den Berg <faxuser@proton.me>
Reported-by: Brian van den Berg <faxuser@proton.me>
Link: https://lore.kernel.org/all/370007e6-b73b-4bfc-8410-a860781c7ad7@proton.me/
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20260731-uac-lg-pro-x-2-ls-v1-1-268eaefe66ab@rong.moe
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the code for managing the firmware loading in the 6fire
driver with __free(firmware) and __free(kfree), so that the loaded
firmware and the name string are cleaned up automatically.
Only the code refactoring, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260729083735.120219-2-tiwai@suse.de
As snd_usb_quirk_flags_from_name() is used only locally, make it
local. Also, drop the unused snd_usb_quirk_flag_find_name(), too.
Only a code cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260729074523.92761-4-tiwai@suse.de
The C-Media CM6206 (0d8c:0102) truncates the three-byte sample rate it
returns for UAC_GET_CUR to its two low bytes. After the rate has been
set to 96000 (0x017700) the device reports back 30464 (0x007700).
At probe time the driver initializes every altsetting to its maximum
rate, so altsetting 5 is set to 96000 and the warning appears on each
plug-in, before anything has opened the device:
usb 3-1.3: 1:5 Set sample rate 96000, clock 0
usb 3-1.3: current rate 30464 is different from the runtime rate 96000
That altsetting is the one parse_audio_format_rates_v1() already fixes
up for this chip, so this affects every CM6206.
Only the read-back is broken, the rate itself is applied: a 1 kHz sine
rendered at 96 kHz is recovered at 1000.2 Hz, and a silent fallback to
48000 would have been reported as 0x00bb80 rather than as the low half
of the requested rate.
Add a QUIRK_FLAG_GET_SAMPLE_RATE entry for the device so the read-back
is skipped. Setting the same flag through the quirk_flags module
parameter makes the warning disappear while the 96000 init still
happens.
Signed-off-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Link: https://patch.msgid.link/20260728222239.62749-1-mikhail.v.gavrilov@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usb_handle_sync_urb() scales received sync packet sizes by the sender's
stride and stores the result directly in out_packet->packet_size[i]. If a
connected USB device sends an oversized sync packet, this frame count can
exceed ep->maxframesize.
The un-clamped frame count then propagates to the playback endpoint queue,
potentially driving packet transfers beyond the endpoint's hardware frame
limits.
Cap the calculated frame count against ep->maxframesize in
snd_usb_handle_sync_urb() to prevent oversized packets from entering the
playback queue.
Fixes: 28acb12014 ("ALSA: usb-audio: use sender stride for implicit feedback")
Cc: stable@vger.kernel.org
Assisted-by: Jetski:Gemini-3.6-Flash
Signed-off-by: Sonali Pradhan <sonalipradhan@google.com>
Link: https://patch.msgid.link/20260728202432.2354994-1-sonalipradhan@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a USB audio endpoint requests full packet transfers via the fill_max
descriptor flag, data_ep_set_params() promotes ep->curpacksize to
ep->maxpacksize. However, maxsize is left at the original sample-rate
derived value.
Since u->buffer_size is allocated as maxsize * packets, the resulting
DMA buffer is far too small for the requested transfer length. When the
USB host controller streams up to curpacksize bytes per packet, it writes
past the end of the buffer via DMA, corrupting kernel heap memory.
Update maxsize to curpacksize when fill_max is set so that the allocated
DMA buffer size matches the actual transfer request size.
[ changed to reassign maxsize only when ep->fill_max is set -- tiwai ]
Fixes: 8fdff6a319 ("ALSA: snd-usb: implement new endpoint streaming model")
Cc: stable@vger.kernel.org
Assisted-by: Jetski:Gemini-3.6-Flash
Signed-off-by: Sonali Pradhan <sonalipradhan@google.com>
Link: https://patch.msgid.link/20260728201716.2347726-1-sonalipradhan@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This USB Audio device (0x1e0b:0xd01e) exhibits audio stuttering
during boot when playing audio. Once the system is fully booted,
playback is normal.
The device reports its isochronous endpoints with the Asynchronous
sync type (bmAttributes = 0x03), which causes the driver to
calculate nurbs = min(max_urbs, ...) = 3, providing only ~16ms
of buffering. During boot, the higher system scheduling jitter
(e.g., from init scripts, device enumeration, and driver probing)
can exceed this buffer depth, causing audible stuttering.
This patch adds a device-specific quirk (QUIRK_FLAG_PLAYBACK_URB_FIXUP)
that applies two changes for this device:
1. Forces nurbs to MAX_URBS (12), providing sufficient buffering
2. Sets URB_ISO_ASAP flag for more consistent xHCI scheduling
Both changes are required together for stable boot-time playback:
- The larger buffer absorbs scheduling jitter during boot
- URB_ISO_ASAP ensures consistent URB submission timing, preventing
the xHCI scheduler from introducing variable delays
Test methodology:
- Without patch: reboot and play audio → stuttering audible in all
tests (reproduced consistently across multiple attempts)
- With nurbs=8 only: occasional minor stuttering observed after
multiple tests (insufficient buffer depth)
- With full patch (nurbs=12 + URB_ISO_ASAP): reboot and play audio
→ no stuttering observed (tested in 10+ reboot cycles without
reproducing the issue)
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260728111309.1271834-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add USB mixer mapping quirk for later revisions of the Corsair Virtuoso
headset with USB IDs 0x1b1c:0x0a43 (wired) and 0x1b1c:0x0a44
(wireless). These devices exhibit the same mixer label collision as
earlier Virtuoso variants: all controls are labelled "Headset", causing
applications like PulseAudio to move the sidetone control instead of
the main playback volume.
Signed-off-by: Robert Abrahamse <denobyte2@gmail.com>
Link: https://patch.msgid.link/20260728140314.11601-1-denobyte2@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to support AW88399 HDA side codec used on the Lenovo Legion we
need updates to it's ASoC driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmpnR1EACgkQJNaLcl1U
h9B0hQf9EeMLXKaJD6V/3b/P9ecRlGgIHThSwZhvz+DM/VU9jtdINNc4gPJI6ZvJ
FhFAuvACVLCKbT/rN++eBjJ7CwsmquYlDsc4NQ3R1IKtpkd/RMqRh+7v7786FNH9
X743S2SewaGO9bUn05SOYLPNU56MWM4Kuhpj1DkZH8ceQWe3wVrWRuuLr+9YLsi8
z1LoFv+RCXKASJ6oVNLDUTVK/rN9cw2glgAaTn/IVET2SyqUuv0xivqLExpJb7rS
tPrNEqwdOKUX9Y8cRgAXiI4Apsj7TylLhyFKPW+CGcK9kpozHVj68Ot4ZRKJy1Zj
dNjWmij89Qm1ai+W8yHI7kNjAumOHw==
=LvPK
-----END PGP SIGNATURE-----
Merge tag 'asoc-aw88339-lib' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Add AW88399 HDA side codec driver for Lenovo Legion
In order to support AW88399 HDA side codec used on the Lenovo Legion we
need updates to it's ASoC driver.
Although 6fire driver had a few fixes for dealing with the early error
handling during the probe phase, it forgot a pending URB before
freeing the resources, which may lead to a UAF.
This patch addresses it by doing the almost same cleanup procedure
like the normal disconnect phase at the error path.
Reported-and-tested-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Closes: https://lore.kernel.org/20260724030900.1984491-1-shuangpeng.kernel@gmail.com
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260726074821.2288158-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usbmidi_akai_output() computes its fill-loop bound
buf_end = ep->max_transfer - MAX_AKAI_SYSEX_LEN - 1;
as a signed int, so a small device-advertised bulk-OUT max_transfer
makes buf_end negative. The loop guard then compares the u32
urb->transfer_buffer_length against that negative int: the usual
arithmetic conversion turns buf_end into a large unsigned value, so the
guard stays true and each iteration keeps appending SysEx framing and
payload bytes past the end of the URB transfer buffer, which is only
max_transfer bytes long.
A USB device that advertises a tiny bulk-OUT endpoint can therefore
trigger an attacker-length- and content-controlled heap out-of-bounds
write when a process writes to the created /dev/snd/midiC*D* node.
Return early when there is no room for even one SysEx, so the loop is
never entered with a bound that would wrap. The loop is the last
statement of the function, so bailing out is equivalent to it not
running.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 4434ade8c9 ("ALSA: usb-audio: add support for Akai MPD16")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260726074500.50145-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_rme_digiface_read_status() reads a four-word status block from the
device into an uninitialised on-stack __le32 buf[4] and, whenever the
vendor control-IN transfer does not return a negative error, copies all
four words into the caller's status[].
snd_usb_ctl_msg() copies the full requested size back into the caller's
buffer regardless of how many bytes the data stage actually delivered:
buf = kmemdup(data, size, GFP_KERNEL);
err = usb_control_msg(dev, pipe, request, requesttype,
value, index, buf, size, timeout);
memcpy(data, buf, size);
usb_control_msg() returns the transferred length on a short control-IN,
which is a non-negative value, and writes only that many bytes. The
remainder of the copy back is the kmemdup()ed image of the caller's
buffer, so a device answering with a short data stage leaves the
trailing words of buf[] holding leftover kernel stack. The only guard
in the caller is err < 0, so those words are stored into status[].
They then reach user space: snd_rme_digiface_get_status_val() selects a
16-bit halfword of status[] per the control's reg/mask, and the eight
Digiface status controls together expose the whole 16-byte frame to an
unprivileged reader of /dev/snd/controlC*.
Zero-initialise the buffer so a short read yields zeros instead of stack
residue. This mirrors snd_rme_get_status1(), which already clears its
output word before the same kind of vendor read.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 611a96f6ac ("ALSA: usb-audio: Add mixer quirk for RME Digiface USB")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260726065020.46070-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
create_midi2_ump() registers a card-owned snd_ump_endpoint and stores a
back-pointer to its per-interface snd_usb_midi2_ump object in
ump->private_data, but it never installs an ump->private_free hook and
never clears that pointer.
If a later step of snd_usb_midi_v2_create() fails, its error path calls
free_all_midi2_umps(), which kfree()s the snd_usb_midi2_ump object while
the already-registered endpoint keeps pointing at it. The created
/dev/snd/umpC*D* node stays exposed, so the first operation of any UMP
open, ump_to_endpoint(), dereferences the dangling ump->private_data and
reads rmidi->eps[dir] out of freed memory.
A malicious USB MIDI 2.0 device that makes creation fail after the
endpoint is registered can thus trigger a slab use-after-free read on a
subsequent open of the UMP node.
Clear the endpoint's back-pointer before freeing the object, and let
ump_to_endpoint() tolerate a NULL private_data so the open/close/trigger
callbacks fail cleanly (their callers already handle a NULL endpoint)
instead of dereferencing a stale pointer.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: ff49d1df79 ("ALSA: usb-audio: USB MIDI 2.0 UMP support")
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260726051337.41124-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting up the interface when suspended/resuming fails on this card.
Adding a reset and delay quirk will eliminate this problem.
Note: This device's VID conflicts with Apple's (0x05ac).
usb 1-1: New USB device found, idVendor=05ac, idProduct=110b
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Q2A
usb 1-1: Manufacturer: JKY Technology
usb 1-1: SerialNumber: 330270D2251225
Suggested-by: Rong Zhang <i@rong.moe>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Reviewed-by: Rong Zhang <i@rong.moe>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/TYUPR06MB6217566CFD33F57D3AE46816D2CF2@TYUPR06MB6217.apcprd06.prod.outlook.com
The Razer Barracuda X 2.4 GHz USB headset dongle (0x1532:0x0552)
reports a minimum volume register value of cval->min = -16800.
In UAC 1/256 dB units, -16800 corresponds to -65.625 dB. However,
stock ALSA misinterprets this raw integer as 1/100 dB units
(-168.00 dB), causing user-space audio servers (PipeWire /
PulseAudio) to map their volume curves against an incorrectly wide
range.
Add an explicit usbmix_dB_map entry overriding Unit 2 to -6562
(-65.62 dB) to accurately report the physical hardware
attenuation bounds.
Signed-off-by: Markus Lindner <lindner.markus@outlook.at>
Link: https://patch.msgid.link/AS8P195MB2142F4EFF83980BD02BA6566E1C12@AS8P195MB2142.EURP195.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting up the interface when suspended/resuming fails on this card.
Adding a reset and delay quirk will eliminate this problem.
usb 1-1: New USB device found, idVendor=0124, idProduct=0c21
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB Headphone
usb 1-1: Manufacturer: Generic
usb 1-1: SerialNumber: 20210726905926
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/TYUPR06MB6217CBB68C8F868C076A4353D2C12@TYUPR06MB6217.apcprd06.prod.outlook.com
JBL Quantum650 Wireless (0ecb:2125) requires the same workaround that
was used for JBL Quantum610 and Quantum810 for limiting the sample rate.
Without it, the capture (microphone) stream fails to work. Setting the
QUIRK_FLAG_FIXED_RATE flag, as done for the sibling models, makes both
playback and capture work correctly.
Signed-off-by: Daniel C. Ribeiro <dcoutinho.96@gmail.com>
Link: https://patch.msgid.link/20260719090037.40149-1-dcoutinho.96@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio control requests that sets sampling frequency sometimes fail on
this card. Adding delay between control messages eliminates that problem.
usb 1-1: New USB device found, idVendor=2fc6, idProduct=f0b5
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: iBasso DC-Elite
usb 1-1: Manufacturer: iBasso
usb 1-1: SerialNumber: CTUA171130B
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/TYUPR06MB6217D8FF419F24378196FCEFD2FA2@TYUPR06MB6217.apcprd06.prod.outlook.com
Salvador reported that the recent fix for applying the DSD quirk to
Musical Fidelity devices broke for his M6s DAC model (2772:0502).
Although this is basically a firmware bug, the model in question is
fairly old, and no further firmware update can be expected, so it'd be
better to address in the driver side.
As an ad hoc workaround, skip the DSD quirk for this device by adding
an empty quirk entry of 2772:0502; this essentially skips the later
DSD quirk entry by the match with the vendor 2772.
Fixes: da3a7efff6 ("ALSA: usb-audio: Update for native DSD support quirks")
Reported-by: Salvador Blaya <tiniebla6@gmail.com>
Closes: https://lore.kernel.org/CAOdyq+qFaqCh=tK_wNnA64hv5pQuA1Y09ANxQ=xK8yR-t4mf9Q@mail.gmail.com
Tested-by: Salvador Blaya <tiniebla6@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260709095614.1418838-1-tiwai@suse.de
The device with USB ID 040b:0897 (Weltrend Semiconductor chipset,
sold rebranded as the Redragon H510-PRO Wireless headset, reporting
"XiiSound Technology Corporation" in its USB string descriptors)
reports a constant value on GET_CUR for its PCM Playback Volume
control while still supporting an actually tunable volume. This
trips the sticky-value detection in check_sticky_volume_control(),
which disables the mixer control entirely:
usb 1-4: 5:0: sticky mixer values (0/100/1 => 80), disabling
As a result, the device boots with playback volume effectively muted
and provides no way to raise it through the normal ALSA/PipeWire
mixer path.
Apply QUIRK_FLAG_MIXER_GET_CUR_BROKEN so the sticky check marks the
control as get_cur_broken and relies on the cached value instead of
disabling the mixer control outright.
Tested by backporting this quirk flag and the supporting
get_cur_broken logic onto a Linux 7.1.2-zen kernel build that does
not yet carry it, and confirming that after applying the flag the
kernel log changes from
usb 1-4: 5:0: sticky mixer values (0/100/1 => 80), disabling
to
usb 1-4: 5:0: broken mixer GET_CUR (0/100/1 => 80)
with the control usable via the driver's cached value afterward.
Signed-off-by: Agustin Luzardo <agustinluzardo09@gmail.com>
Link: https://patch.msgid.link/20260705184227.113588-1-agustinluzardo09@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I accidentally made an off-by-a-line mistake when mimicking other code
paths that set all channels. The mistake breaks sticky mixers with
multiple channels.
I didn't realize this mistake at that time, as my device's mixer is
single-channel.
Fix it, so that per-channel volume of sticky mixers is balanced.
Fixes: aa2f4addab ("ALSA: usb-audio: Set the value of potential sticky mixers to maximum")
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20260706-uac-sticky-channels-fix-v1-1-92741c538283@rong.moe
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb_ep1_command_reply_dispatch() uses buf[0] as a command byte and then
reads command-specific fixed items from the same URB buffer. Several
paths use buf + 1, buf[1], buf[2], or buf + 3 without first proving that
urb->actual_length contains those bytes.
Add per-command length checks, use a payload length derived from the
bytes after the command byte for the control-state copy, and reject short
analog input payloads before the input helper reads fixed offsets from
the EP1 reply.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260705084601.56400-1-pengpeng@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tascam_disconnect() cancels capture_work and midi_in_work before
usb_kill_anchored_urbs() kills the capture/MIDI-in URBs. Those URBs
self-resubmit, and their completion handlers reschedule the work.
A URB that completes in the small window between cancel_work_sync() and
usb_kill_anchored_urbs() therefore re-arms the work after its only
cancel. Nothing cancels it again before snd_card_free() frees the
card-private tascam structure, so the work handler then runs on freed
memory.
Kill the anchored URBs before cancelling the work; once the work is
cancelled no remaining URB can complete to re-arm it.
Fixes: c1bb0c13e4 ("ALSA: usb-audio: us144mkii: Implement audio capture and decoding")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: HyeongJun An <sammiee5311@gmail.com>
Link: https://patch.msgid.link/20260701095231.1020811-1-sammiee5311@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Pioneer DJ DJM-S11, a professional 2-port DJ mixer, is currently not
recognized as an audio interface and therefore not usable on Linux. This
patch enables its full audio functionality.
Like other mixers in the Pioneer DJ DJM family, the DJM-S11 uses
vendor-specific USB class descriptors (0xff) and requires custom mixer
quirks to expose the hardware's input capture routing and volume
controls.
Add the USB vendor and product ID (2b73:0037) to quirks-table.h, mapping
the control interface (Interface 0) to trigger the standard mixer quirks,
and establishing the audio formats for the playback and capture streams.
Control interface 3 is likely related to the touchscreen which is
capable to display waveforms, etc. This functionality is not supported.
In mixer_quirks.c, add the DSP routing options for the DJM-S11. This
creates the ALSA kcontrols for selecting the capture sources (Phono,
Line, Post-fader, etc.) and initializes the default DSP state during
the device probe.
Note that the DJM-S11's capture endpoint clock is strictly slaved to
its playback endpoint. Capturing audio (e.g., timecode vinyl DVS input)
physically requires an active playback stream on the output channels
to feed the master word clock back to the capture stage. Userspace
audio servers (such as PipeWire or JACK) should be configured in
full-duplex mode or have automatic node suspension disabled to maintain
the clock line and prevent I/O errors during capture.
Signed-off-by: Federico Beffa <beffa@fbengineering.ch>
Link: https://patch.msgid.link/20260625115340.823184-1-beffa@fbengineering.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb_audio_probe() can create USB-audio component resources before the
first interface is recorded in chip->num_interfaces. If a later probe
step fails, the error path drops chip->active and frees the card directly
when no interfaces have been registered.
Normal disconnect first releases USB-audio components in a fixed order
before the card is freed. The first-interface probe error path skipped
that sequence, so partially initialized PCM, endpoint, MIDI, media, or
mixer resources could be left for the card private_free path without their
disconnect handling having run.
Move the existing normal-disconnect component release sequence into a
helper and call it from the zero-interface probe error path before
snd_card_free(). Keep the normal disconnect ordering unchanged: PCM
streams, endpoint resources, MIDI 1.0 resources, MIDI 2.0 resources, media
device cleanup, then mixer resources.
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Link: https://patch.msgid.link/20260618170026.192212-1-zzzccc427@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In capture_urb_complete(), usb_anchor_urb() is called on every
completion callback, but the URB is already anchored from the
initial submission in tascam_trigger_start(). Each redundant call
corrupts the anchor's doubly-linked list and inflates the URB
refcount. When usb_kill_anchored_urbs() traverses the list during
stream stop / suspend / disconnect, the corrupted list leads to
use-after-free.
Remove the redundant usb_anchor_urb() from the resubmit path.
Cc: stable@vger.kernel.org
Fixes: c1bb0c13e4 ("ALSA: usb-audio: us144mkii: Implement audio capture and decoding")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20260627042949.61767-1-vulab@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
