Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.
Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.
Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow us to build infrastructure which needs to know the size of a value
without requiring regmap based drivers to supply this information to both
ASoC and regmap by asking regmap for the value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KhUJ
-----END PGP SIGNATURE-----
Merge tag 'topic/introspection' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into HEAD
New interfaces to allow other subsystems to gather information about the
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
Merged into ASoC in order to allow us to implement SND_SOC_BYTES_MASK()
controls which need to know the word size of the underlying registers.
Fall back to a register by register read to do so; most likely we'll be
cache only so the overhead will be low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove omap_uart_can_sleep and
add pm_qos) removed omap_uart_can_sleep and omap3_can_sleep, but not
their declarations. So remove those now.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove
omap_uart_can_sleep and add pm_qos) removed the last usage of
'can_sleep' but did not remove the field.
commit 8612bd22f3 (ARM: OMAP2+: UART: Avoid console uart idling
during bootup) removed the last non-trivial use of 'pdev'.
So remove these fields and the one trivial use.
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The connectable/discoverable flags need to be changed before sending the
response since otherwise the settings value will be incorrect.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Now that most flags are persistent, only the LE_SCAN flag should be
cleared after a reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When powered off and doing changes to the Connectable or Discoverable
setting we should also send an appropriate New Settings event in
addition to the command response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The New Settings event needs to be sent from quite many places so it
makes sense to have a convenience function for it to simplify the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
We should not stop iterating through the various settings if powered off
since most may still be set even then.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
When switching connectable mode off any pending discoverable timeout
must also be disabled to avoid duplicate write_scan_enable commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to toggle the connectable & discoverable
settings when powered off. Two new hdev->dev_flags flags are added to
track what the scan mode should be when the device is finally powered
on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Walking through the tasklist in cgroup_enable_task_cg_list() inside
an RCU read side critical section is not enough because:
- RCU is not (yet) safe against while_each_thread()
- If we use only RCU, a forking task that has passed cgroup_post_fork()
without seeing use_task_css_set_links == 1 is not guaranteed to have
its child immediately visible in the tasklist if we walk through it
remotely with RCU. In this case it will be missing in its css_set's
task list.
Thus we need to traverse the list (unfortunately) under the
tasklist_lock. It makes us safe against while_each_thread() and also
make sure we see all forked task that have been added to the tasklist.
As a secondary effect, reading and writing use_task_css_set_links are
now well ordered against tasklist traversing and modification. The new
layout is:
CPU 0 CPU 1
use_task_css_set_links = 1 write_lock(tasklist_lock)
read_lock(tasklist_lock) add task to tasklist
do_each_thread() { write_unlock(tasklist_lock)
add thread to css set links if (use_task_css_set_links)
} while_each_thread() add thread to css set links
read_unlock(tasklist_lock)
If CPU 0 traverse the list after the task has been added to the tasklist
then it is correctly added to the css set links. OTOH if CPU 0 traverse
the tasklist before the new task had the opportunity to be added to the
tasklist because it was too early in the fork process, then CPU 1
catches up and add the task to the css set links after it added the task
to the tasklist. The right value of use_task_css_set_links is guaranteed
to be visible from CPU 1 due to the LOCK/UNLOCK implicit barrier properties:
the read_unlock on CPU 0 makes the write on use_task_css_set_links happening
and the write_lock on CPU 1 make the read of use_task_css_set_links that comes
afterward to return the correct value.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Remove the stale comment about RCU protection. Many callers
(all of them?) of cgroup_enable_task_cg_list() don't seem
to be in an RCU read side critical section. Besides, RCU is
not helpful to protect against while_each_thread().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit handles workloads that transition quickly between idle and
non-idle, and where the CPU's callbacks cannot be invoked, but where
RCU does not have anything immediate for the CPU to do. Without this
patch, the RCU_FAST_NO_HZ code can be invoked repeatedly on each entry
to idle. The commit sets the per-CPU rcu_dyntick_holdoff variable to
hold off further attempts for a tick.
Reported-by: "Abou Gazala, Neven M" <neven.m.abou.gazala@intel.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If a softirq is pending, the current CPU has RCU callbacks pending,
and RCU does not immediately need anything from this CPU, then the
current code resets the RCU_FAST_NO_HZ state machine. This means that
upon exit from the subsequent softirq handler, RCU_FAST_NO_HZ will
try really hard to force RCU into dyntick-idle mode. And if the same
conditions hold after a few tries (determined by RCU_IDLE_OPT_FLUSHES),
the same situation can repeat, possibly endlessly. This scenario is
not particularly good for battery lifetime.
This commit therefore suppresses the early exit from the RCU_FAST_NO_HZ
state machine in the case where there is a softirq pending. This change
forces the state machine to retain its memory, and to enter holdoff if
this condition persists.
Reported-by: "Abou Gazala, Neven M" <neven.m.abou.gazala@intel.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It doesn't make sense to trace irq off or do irq flags
lock proving inside 'this_cpu' operations, so replace local_irq_*
with raw_local_irq_* in 'this_cpu' op.
Also the patch fixes onelockdep warning[1] by the replacement, see
below:
In commit: 933393f58fef9963eac61db8093689544e29a600(percpu:
Remove irqsafe_cpu_xxx variants), local_irq_save/restore(flags) are
added inside this_cpu_inc operation, so that trace_hardirqs_off_caller
will be called by trace_hardirqs_on_caller directly because
__debug_atomic_inc is implemented as this_cpu_inc, which may trigger
the lockdep warning[1], for example in the below ARM scenary:
kernel_thread_helper /*irq disabled*/
->trace_hardirqs_on_caller /*hardirqs_enabled was set*/
->trace_hardirqs_off_caller /*hardirqs_enabled cleared*/
__this_cpu_add(redundant_hardirqs_on)
->trace_hardirqs_off_caller /*irq disabled, so call here*/
The 'unannotated irqs-on' warning will be triggered somewhere because
irq is just enabled after the irq trace in kernel_thread_helper.
[1],
[ 0.162841] ------------[ cut here ]------------
[ 0.167694] WARNING: at kernel/lockdep.c:3493 check_flags+0xc0/0x1d0()
[ 0.174468] Modules linked in:
[ 0.177703] Backtrace:
[ 0.180328] [<c00171f0>] (dump_backtrace+0x0/0x110) from [<c0412320>] (dump_stack+0x18/0x1c)
[ 0.189086] r6:c051f778 r5:00000da5 r4:00000000 r3:60000093
[ 0.195007] [<c0412308>] (dump_stack+0x0/0x1c) from [<c00410e8>] (warn_slowpath_common+0x54/0x6c)
[ 0.204223] [<c0041094>] (warn_slowpath_common+0x0/0x6c) from [<c0041124>] (warn_slowpath_null+0x24/0x2c)
[ 0.214111] r8:00000000 r7:00000000 r6:ee069598 r5:60000013 r4:ee082000
[ 0.220825] r3:00000009
[ 0.223693] [<c0041100>] (warn_slowpath_null+0x0/0x2c) from [<c0088f38>] (check_flags+0xc0/0x1d0)
[ 0.232910] [<c0088e78>] (check_flags+0x0/0x1d0) from [<c008d348>] (lock_acquire+0x4c/0x11c)
[ 0.241668] [<c008d2fc>] (lock_acquire+0x0/0x11c) from [<c0415aa4>] (_raw_spin_lock+0x3c/0x74)
[ 0.250610] [<c0415a68>] (_raw_spin_lock+0x0/0x74) from [<c010a844>] (set_task_comm+0x20/0xc0)
[ 0.259521] r6:ee069588 r5:ee0691c0 r4:ee082000
[ 0.264404] [<c010a824>] (set_task_comm+0x0/0xc0) from [<c0060780>] (kthreadd+0x28/0x108)
[ 0.272857] r8:00000000 r7:00000013 r6:c0044a08 r5:ee0691c0 r4:ee082000
[ 0.279571] r3:ee083fe0
[ 0.282470] [<c0060758>] (kthreadd+0x0/0x108) from [<c0044a08>] (do_exit+0x0/0x6dc)
[ 0.290405] r5:c0060758 r4:00000000
[ 0.294189] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.299041] possible reason: unannotated irqs-on.
[ 0.303955] irq event stamp: 5
[ 0.307159] hardirqs last enabled at (4): [<c001331c>] no_work_pending+0x8/0x2c
[ 0.314880] hardirqs last disabled at (5): [<c0089b08>] trace_hardirqs_on_caller+0x60/0x26c
[ 0.323547] softirqs last enabled at (0): [<c003f754>] copy_process+0x33c/0xef4
[ 0.331207] softirqs last disabled at (0): [< (null)>] (null)
[ 0.337585] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'fixes' of git://github.com/hzhuang1/linux:
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
RCU, RCU-bh, and RCU-sched read-side critical sections are forbidden
in the inner idle loop, that is, between the rcu_idle_enter() and the
rcu_idle_exit() -- RCU will happily ignore any such read-side critical
sections. However, things like powertop need tracepoints in the inner
idle loop.
This commit therefore provides an RCU_NONIDLE() macro that can be used to
wrap code in the idle loop that requires RCU read-side critical sections.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Use of RCU in the idle loop is incorrect, quite a few instances of
just that have made their way into mainline, primarily event tracing.
The problem with RCU read-side critical sections on CPUs that RCU believes
to be idle is that RCU is completely ignoring the CPU, along with any
attempts and RCU read-side critical sections.
The approaches of eliminating the offending uses and of pushing the
definition of idle down beyond the offending uses have both proved
impractical. The new approach is to encapsulate offending uses of RCU
with rcu_idle_exit() and rcu_idle_enter(), but this requires nesting
for code that is invoked both during idle and and during normal execution.
Therefore, this commit modifies rcu_idle_enter() and rcu_idle_exit() to
permit nesting.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
There is now an unconditional check for rcu_head misalignment in
__call_rcu(), so remove the old conditional one in debug_rcu_head_queue().
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
constant c;
@@
*e = c
... when != e = e1
when != &e
when != true IS_ERR(e)
*PTR_ERR(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The WARN_ON_ONCE() in rcu_lock_acquire() results in infinite recursion
on S390, and also doesn't print very much information. Remove this.
Updated patch to add lockdep-RCU assertions to RCU's read-side primitives.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Fix a bonehead error introduced when adding event tracing to rcutorture.
Move the traces to follow the NULL-pointer checks.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The expedited RCU primitives can be quite useful, but they have some
high costs as well. This commit updates and creates docbook comments
calling out the costs, and updates the RCU documentation as well.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Because newly offlined CPUs continue executing after completing the
CPU_DYING notifiers, they legitimately enter the scheduler and use
RCU while appearing to be offline. This calls for a more sophisticated
approach as follows:
1. RCU marks the CPU online during the CPU_UP_PREPARE phase.
2. RCU marks the CPU offline during the CPU_DEAD phase.
3. Diagnostics regarding use of read-side RCU by offline CPUs use
RCU's accounting rather than the cpu_online_map. (Note that
__call_rcu() still uses cpu_online_map to detect illegal
invocations within CPU_DYING notifiers.)
4. Offline CPUs are prevented from hanging the system by
force_quiescent_state(), which pays attention to cpu_online_map.
Some additional work (in a later commit) will be needed to
guarantee that force_quiescent_state() waits a full jiffy before
assuming that a CPU is offline, for example, when called from
idle entry. (This commit also makes the one-jiffy wait
explicit, since the old-style implicit wait can now be defeated
by RCU_FAST_NO_HZ and by rcutorture.)
This approach avoids the false positives encountered when attempting to
use more exact classification of CPU online/offline state.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It is illegal to use RCU from a CPU that has reported idleness or
offlinedness to RCU. However, it can be quite difficult to determine
from a stack trace whether or not a given CPU is idle or offline.
Therefore, this commit adds idle/offline diagnostics to the lockdep-RCU
error message.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_prepare_for_idle() function is always called with interrupts
disabled, so there is no reason to disable interrupts again within
rcu_prepare_for_idle(). Therefore, this commit removes all of the
interrupt disabling, also removing a latent disabling-unbalance bug.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that TREE_RCU and TREE_PREEMPT_RCU no longer do anything different
for the single-CPU case, there is no need for multiple definitions of
synchronize_sched_expedited(). It is no longer in any sense a plug-in,
so move it from kernel/rcutree_plugin.h to kernel/rcutree.c.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Although it is legal to use RCU during early boot, it is anything
but legal to use RCU at runtime from an offlined CPU. After all, RCU
explicitly ignores offlined CPUs. This commit therefore adds checks
for runtime use of RCU from offlined CPUs.
These checks are not perfect, in particular, they can be subverted
through use of things like rcu_dereference_raw(). Note that it is not
possible to put checks in rcu_read_lock() and friends due to the fact
that these primitives are used in code that might be used under either
RCU or lock-based protection, which means that checking rcu_read_lock()
gets you fat piles of false positives.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The following commit:
b52956c perf tools: Allow multiple threads or processes in record, stat, top
introduced a bug in the thread_map code which caused perf record -a to
not setup system-wide monitoring properly.
$ taskset -c 1 noploop 1000 &
$ perf record -a -C 1 sleep 10
$ perf report -D | tail -20
cycles stats:
TOTAL events: 4413
MMAP events: 4025
COMM events: 340
SAMPLE events: 48
Here I was expecting about 10,000 samples and not 48.
In system-wide mode, the PID passed to perf_event_open() must be -1 and
it was 0. That caused the kernel to setup a per-process event on PID:0.
Consequently, the number of samples captured does not correspond to the
requested measurement.
The following one-liner fixes the problem for me with or without -C.
I would also suggest to change the malloc() to something that matches
the struct definition. thread_map->map[] is declared as int map[] and
not pid_t map[]. If map[] can only contain pids, then change the struct
definition.
Acked-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120221145424.GA6757@quad
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
isdn source code uses a not-current coding style.
Update the coding style used on a per-line basis
so that git diff -w shows only elided blank lines
at EOF.
Done with emacs and some scripts and some typing.
Built x86 allyesconfig.
No detected change in objdump -d or size.
Signed-off-by: Joe Perches <joe@perches.com>
Add documentation of CONFIG_RCU_CPU_STALL_VERBOSE, CONFIG_RCU_CPU_STALL_INFO,
and RCU_STALL_DELAY_DELTA. Describe multiple stall-warning messages from
a single stall, and the timing of the subsequent messages. Add headings.
Remove RCU_SECONDS_TILL_STALL_RECHECK because this value is now computed
at runtime from RCU_CPU_STALL_TIMEOUT, so that sysfs changes to the timeout
value now directly affect the RCU_SECONDS_TILL_STALL_RECHECK value.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add module parameters to rcutorture that induce a CPU stall.
The stall_cpu parameter specifies how long to stall in seconds,
defaulting to zero, which indicates no stalling is to be undertaken.
The stall_cpu_holdoff parameter specifies how many seconds after
insmod (or boot, if rcutorture is built into the kernel) that this
stall is to start. The default value for stall_cpu_holdoff is ten
seconds.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The torture.txt documentation gives an example rcutorture run with a
100-second duration. This is ridiculously short, unless maybe testing
a fix for a egregious bug. Use a more-realistic one-hour duration for
the example.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
When rcutorture is started automatically at boot time, it might well
also start CPU-hotplug operations at that time, which might not be
desirable. This commit therefore adds an rcutorture parameter that
allows CPU-hotplug operations to be held off for the specified number
of seconds after the start of boot.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There have been situations where RCU CPU stall warnings were caused by
issues in scheduling-clock timer initialization. To make it easier to
track these down, this commit causes the RCU CPU stall-warning messages
to print out the number of scheduling-clock interrupts taken in the
current grace period for each stalled CPU.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The default CONFIG_RCU_CPU_STALL_TIMEOUT value of 60 seconds has served
Linux users well for production use for quite some time. However, for
debugging, there will be more than three minutes between subsequent
stall-warning messages. This can be an annoyingly long wait if you
are trying to work out where the offending infinite loop is hiding.
Therefore, this commit provides a rcu_cpu_stall_timeout sysfs
parameter that may be adjusted at boot time and at runtime to speed
up debugging.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that both TINY_RCU and TINY_PREEMPT_RCU have been in place for awhile,
it is time to remove UP support from TREE_RCU, which is what this commit
does.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There is no convenient expression for rcu_deference_protected()
when it is used in tearing down multilinked structures following
a grace period. For example, suppose that an element containing an
RCU-protected pointer to a second element is removed from an enclosing
RCU-protected data structure, then the write-side lock is released,
and finally synchronize_rcu() is invoked to wait for a grace period.
Then it is necessary to traverse the pointer in order to free up the
second element. But we are not in an RCU read-side critical section
and we are holding no locks, so the usual rcu_dereference_check() and
rcu_dereference_protected() primitives are not appropriate. Neither
is rcu_dereference_raw(), as it is intended for use in data structures
where the user defines the locking design (for example, list_head).
So this responsibility is added to rcu_access_pointer()'s list, and
this commit updates rcu_assign_pointer()'s header comment accordingly.
Suggested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Although it is OK to be preempted in an RCU read-side critical section
for TREE_PREEMPT_RCU, it is definitely not OK to be preempted, block,
or might_sleep() within an RCU read-side critical section for TREE_RCU.
Unfortunately, rcu_might_sleep() currently only checks for RCU-bh and
RCU-sched read-side critical sections. This commit therefore makes
rcu_might_sleep() check for RCU read-side critical sections, but only
in TREE_RCU builds.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The inner idle loop is an extended quiescent state for all flavors
of RCU, but there have been recent bug involving use of RCU read-side
primitives from within the idle loop. Therefore, this commit enlists
lockdep-RCU to detect attempts to enter the inner idle loop while in
an RCU read-side critical section, emitting a lockdep-RCU splat if so.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
