Visstrim_M10 has an external class D amplifier.
This patch provides support for controlling the 4
possible gain levels and per channel muting.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal. As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume. Add the missing register
write.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise, we are left with pretty bogus message saying that the pixel
format is not supported while leaving the details to the telepatic powers.
v2: use DRM_DEBUG_KMS instead of DRM_ERROR
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we're using the sprite WM fields, we need to take care not to
clobber them in the main update_wm functions. While we're at it, make
sure we mask out the old sprite wm value before or'ing in the new one
when the sprite wm is updated.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've reviewed gen2 pageflip code to hunt down multiple prepare pageflip
issues. The only thing I've found is a slight but functionally
meaningless confusion about the length of the mi cmd.
Fix it up and add a comment about what this dword should be (according
to docs at least).
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
USB data transfers may not work if the buffer is allocated at
the stack. Be sure to use kmalloc on all places where a buffer
is needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several changes were needed to make az6007 to work, producing
the same commands as the original driver. This patch does
that.
While here, be less verbose when debug is not enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mcp_priv() does unexpected things when passed a void pointer. Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver were written to use a previous solution for MFE at dvb-usb.
Due to the internal API changes, change the binding to work with the
new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code still needs to be commented, as there's a mutex
missing at the az6007_read() call. A mutex there is needed,
in order to prevent RC (or CI) calls while other operations
are in progress.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces no functional changes. It basically defines
a macro for each different req found at the driver, and cleans the
code to use them, making easier to understand the code.
With regards to the IR handling code, although the original code
doesn't define what's the request, it is clear, from the USB logs,
that 0xc5 is for IR polling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use usb_device for those routines, as it allows using them on
all places. While there, rename to better express the meaning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the ngene/ddbridge firmware into their drivers.
There are two reasons for that:
1) The firmware used there didn't work for a few devices
I tested here (Terratec H5, H6 and H7);
2) At least Terratec H7 doesn't seem to require a firmware
for it to work.
After this change, if firmware is not specified, the driver will
use a rom-based firmware (this seems to be the case for Terratec
H7, although I need to better check the USB dumps to be sure about
that).
In any case, the firmware seems to be optional, as the DRX-K driver
don't return the firmware load error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mutex is there to protect the I2C gate. However, for some reason,
it is being called twice:
[ 2103.542796] usbcore: registered new interface driver dvb_usb_az6007
[ 2103.772392] az6007: drxk_gate_ctrl: enable
[ 2103.793900] az6007: drxk_gate_ctrl: enable
For now, let's just comment, to allow the driver to run.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063 uses a one-byte transfer. This requires a special handling
inside the i2c code. Fix it to properly accept i2c reads. This
is needed to make the mt2063 to be detected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some fixes to allow frontend attachment. The patch is not
complete yet, as just the frontend 0 is initialized. So, more
changes will be needed, including some changes at dvb-usb core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Import the az6007 driver from Terratec H7 source, as-is.
It won't compile or run, so latter patches are needed in order
to fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable and disable the clocks to the SPI controller using runtime PM. This
serves the dual purpose of reducing power consumption a little and letting
the core know when the device is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Although the hardware supports interrupts we're not currently using them
at all since for small transfers the overhead is greater than that for
busy waiting and for large transfers we have interrupts from the DMA.
This means that if the hardware reports an error (especially one which
might not stall transfer) we might miss it.
Take a first pass at dealing with such errors by enabling the interrupt
if we can and logging the errors if they happen. Ideally we'd report the
error via the affected transfer but since we're in master mode it's very
difficult to trigger errors at present and this code is much simpler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The perf_event_time() will call perf_cgroup_event_time()
if @event is a cgroup event. Just do it directly and avoid
the extra check..
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/1327021966-27688-2-git-send-email-namhyung.kim@lge.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>