The Amstrad Delta on-board latch2 bit named MODEM_NRESET, now available
as a GPIO pin AMS_DELTA_GPIO_PIN_NMODEM_RESET, is used to power up/down
(bring into/out of a reset state) two distinct on-board devices
simultaneously: the modem, and the voice codec. As a consequence, that
bit is, or can be, manipulated concurrently by two drivers, or their
platform provided hooks.
Instead of updating those drivers to use the gpiolib API as a new method
of controlling the MODEM_NRESET pin state, like it was done to other
drivers accessing latch2 pins, and still being vulnerable to potential
concurrency conflicts, or trying to solve that sharing issue with a
custom piece of code, set up a fixed regulator device on top of that
GPIO pin, with the intention of updating both drivers to manipulate that
regulator, not the GPIO pin directly.
Before the ASoC driver is updated and the modem platform data expanded
with a power management callback for switching its power, the
ams_delta_latch_write() function, which still provides the old API for
accessing latch2 functionality from not updated drivers, is modified to
toggle the regulator instead of the MODEM_NRESET GPIO pin. A helper
function provided for balancing the regulator enable/disable operations,
together with the consumer data needed for tracking the regulator state,
will be removed once the drivers are updated.
Depends on patch series "ARM: OMAP1: ams-delta: replace custom I/O with
GPIO".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PandaBoard features a Texas Instruments WiLink7 Bluetooth
chip, supported by the "btwilink" driver.
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for drivers that recently appeared in kernel:
backlight and TWL4030 poweroff support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sdp4430_spi_board_info.irq was initialized to ETH_KS8851_IRQ and in
omap_4430sdp_init() overwritten with gpio_to_irq(ETH_KS8851_IRQ) before
sdp4430_spi_board_info was registered. This is a bit confusing, so
better don't initialize .irq and document that it is set later.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the EMAC Ethernet controller in the AM35xx SoC.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35xx SoCs include DaVinci EMAC IP. Initialization code in
board-am3517evm.c is pretty board independent and will work for any
AM35xx based board so move this code to it's own file to be reused by
other boards.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change converts TSC2005 related GPIO requests to be done with
gpio_request_array() method and explicitly inits mux configuration for
these GPIOs.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-omap3logic.c
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I'm getting compile failures building this driver, which I narrowed
down to the ilog2 call in ehca_get_max_hwpage_size...
ERROR: ".____ilog2_NaN" [drivers/infiniband/hw/ehca/ib_ehca.ko]
undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
The use of shca->hca_cap_mr_pgsize is confusing the compiler, and
resulting in the __builtin_constant_p in ilog2 going insane.
I tried making it take the u32 pgsize as an argument and the expansion
of shca->_pgsize in the caller, but that failed as well.
With this patch in place, the driver compiles on my GCC 4.6.2 here.
Suggested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Kyle McMartin <kmcmarti@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If we convert and unwritten extent past the current i_size log the size update
as part of the extent manipulation transactions instead of doing an unlogged
metadata update later.
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The kernel IB stack uses one enumeration for IB speed, which wasn't
explicitly specified in the verbs header file. Add that enum, and use
it all over the code.
The IB speed/width notation is also used by iWARP and IBoE HW drivers,
which use the convention of rate = speed * width to advertise their
port link rate.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Replace xfs_ioend_new_eof with a new inline xfs_new_eof helper that
doesn't require and ioend, and is available also outside of xfs_aops.c.
Also make the code a bit more clear by using a normal if statement
instead of a slightly misleading MIN().
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
The new concurrency managed workqueues are cheap enough that we can create
per-filesystem instead of global workqueues. This allows us to remove the
trylock or defer scheme on the ilock, which is not helpful once we have
outstanding log reservations until finishing a size update.
Also allow the default concurrency on this workqueues so that I/O completions
blocking on the ilock for one inode do not block process for another inode.
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
No need to copy received local buffer content to bounce buffer
(DMA buffer) while performing sync READ operation from the chip.
It's applicable for only WRITE operation.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An iser target may send iscsi NO-OP PDUs as soon as it marks the iSER
iSCSI session as fully operative. This means that there is window
where there are no posted receive buffers on the initiator side, so
it's possible for the iSER RC connection to break because of RNR NAK /
retry errors. To fix this, rely on the flags bits in the login
request to have FFP (0x3) in the lower nibble as a marker for the
final login request, and post an initial chunk of receive buffers
before sending that login request instead of after getting the login
response.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* atmel-mci: oops fix against regression introduced in 3.2
* core: power saving regression fix against 3.3-rc1
* core: suspend/resume fix for UHS-I cards
* esdhc-imx: MMC card regression fix against 3.0
* mmci: oops fix for ARM systems with large (64k) pages
* MAINTAINERS update for atmel-mci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fby1
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC fixes from Chris Ball for 3.3:
- atmel-mci: oops fix against regression introduced in 3.2
- core: power saving regression fix against 3.3-rc1
- core: suspend/resume fix for UHS-I cards
- esdhc-imx: MMC card regression fix against 3.0
- mmci: oops fix for ARM systems with large (64k) pages
- MAINTAINERS update for atmel-mci.
* tag 'mmc-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Fixup suspend/resume issues for UHS-I cards
mmc: mmci: reduce max_blk_count to avoid overflowing max_req_size
mmc: sdhci-esdhc-imx: fix for mmc cards on i.MX5
mmc: core: fix regression: set default clock gating delay to 0
MAINTAINERS: hand over atmel-mci (sd/mmc interface)
mmc: atmel-mci: don't use dma features when using DMA with no chan available
Pull from Jiri Kosina:
"Please pull to receive updates for HID layer. Nikolai's patch is
rather important and should still go in for 3.3, as it's a regression
fix for commit b4b583d."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-input: allow array fields out of range
HID: usbhid: Add NOGET quirk for the AIREN Slim+ keyboard
This should make it more clear what this structure is used
for, and how some of the (mutually exclusive) fields are
used to keep page cache references.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We can clear PageWriteback on each page when the IO
completes, but we can't release the references on the page
until we convert any uninitialized extents.
Without this patch, the use of the dioread_nolock mount
option can break buffered writes, because extents may
not be converted by the time a subsequent buffered read
comes in; if the page is not in the page cache, a read
will return zeros if the extent is still uninitialized.
I tested this with a (temporary) patch that adds a call
to msleep(1000) at the start of ext4_end_io_work(), to delay
processing of each DIO-unwritten work queue item. With this
msleep(), a simple workload of
fallocate
write
fadvise
read
will fail without this patch, succeeds with it.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The following command line will leave the aio-stress process unkillable
on an ext4 file system (in my case, mounted on /mnt/test):
aio-stress -t 20 -s 10 -O -S -o 2 -I 1000 /mnt/test/aiostress.3561.4 /mnt/test/aiostress.3561.4.20 /mnt/test/aiostress.3561.4.19 /mnt/test/aiostress.3561.4.18 /mnt/test/aiostress.3561.4.17 /mnt/test/aiostress.3561.4.16 /mnt/test/aiostress.3561.4.15 /mnt/test/aiostress.3561.4.14 /mnt/test/aiostress.3561.4.13 /mnt/test/aiostress.3561.4.12 /mnt/test/aiostress.3561.4.11 /mnt/test/aiostress.3561.4.10 /mnt/test/aiostress.3561.4.9 /mnt/test/aiostress.3561.4.8 /mnt/test/aiostress.3561.4.7 /mnt/test/aiostress.3561.4.6 /mnt/test/aiostress.3561.4.5 /mnt/test/aiostress.3561.4.4 /mnt/test/aiostress.3561.4.3 /mnt/test/aiostress.3561.4.2
This is using the aio-stress program from the xfstests test suite.
That particular command line tells aio-stress to do random writes to
20 files from 20 threads (one thread per file). The files are NOT
preallocated, so you will get writes to random offsets within the
file, thus creating holes and extending i_size. It also opens the
file with O_DIRECT and O_SYNC.
On to the problem. When an I/O requires unwritten extent conversion,
it is queued onto the completed_io_list for the ext4 inode. Two code
paths will pull work items from this list. The first is the
ext4_end_io_work routine, and the second is ext4_flush_completed_IO,
which is called via the fsync path (and O_SYNC handling, as well).
There are two issues I've found in these code paths. First, if the
fsync path beats the work routine to a particular I/O, the work
routine will free the io_end structure! It does not take into account
the fact that the io_end may still be in use by the fsync path. I've
fixed this issue by adding yet another IO_END flag, indicating that
the io_end is being processed by the fsync path.
The second problem is that the work routine will make an assignment to
io->flag outside of the lock. I have witnessed this result in a hang
at umount. Moving the flag setting inside the lock resolved that
problem.
The problem was introduced by commit b82e384c7b ("ext4: optimize
locking for end_io extent conversion"), which first appeared in 3.2.
As such, the fix should be backported to that release (probably along
with the unwritten extent conversion race fix).
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
CC: stable@kernel.org
For extent-based files, you can perform DIO to holes, as mentioned in
the comments in ext4_ext_direct_IO. However, that function passes
DIO_SKIP_HOLES to __blockdev_direct_IO, which is *really* confusing to
the uninitiated reader. The key, here, is that the get_block function
passed in, ext4_get_block_write, completely ignores the create flag
that is passed to it (the create flag is passed in from the direct I/O
code, which uses the DIO_SKIP_HOLES flag to determine whether or not
it should be cleared).
This is a long-winded way of saying that the DIO_SKIP_HOLES flag is
ultimately ignored. So let's remove it.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds a call to gfs2_rindex_update from function gfs2_blk2rgrpd
and removes calls to it that are made redundant by it. The problem is
that a gfs2_grow can add rgrps to the rindex, then put those rgrps into
use, thus rendering the rindex we read in at mount time incomplete.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
twl4030 still doesn't build correctly for x86 allmodconfig. This
fix solves the missing symbol errors.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Over time, we've slowly eliminated the use of sd_rindex_mutex.
Up to this point, it was only used in two places: function
gfs2_ri_total (which totals the file system size by reading
and parsing the rindex file) and function gfs2_rindex_update
which updates the rgrps in memory. Both of these functions have
the rindex glock to protect them, so the rindex is unnecessary.
Since gfs2_grow writes to the rindex via the meta_fs, the mutex
is in the wrong order according to the normal rules. This patch
eliminates the mutex entirely to avoid the problem.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
I've seen users getting very confused by the WARN_ON()s for can_sleep
GPIOs in the atomic-safe paths, the discoverability of the non-atomic
version of the API seems to be hampered by the fact that it's defined
in a header file not the .c file where the warnings are.
Add a couple of comments next to the warnings to help people on their
way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open source gpio on which client
can specify the open source property through GPIO flag
GPIOF_OPEN_SOURCE at the time of gpio request.
The open source pins are normally pulled low and it
cannot be driven to output with value of 0 and so
when client request for setting the pin to LOW, the
gpio will be set to input direction to make pin in tristate
and hence PULL-DOWN on pins will make the state to LOW.
The open source pin can be driven to HIGH by setting output
with value of 1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding details of open drain(open collector) and open source
(open emitter) configuration of the gpio so that client can
set the pin as open drain at the time of gpio request.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The recent addition of volume-knob widget in the auto-parser broke
automute/autoswitch for some Realtek devices.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Production GMA3600/3650 hardware turns out to be subtly different to the
development platforms. This combined with a minor driver bug is causing
the kernel to hang on these platforms.
This patch does the following
- turn down a couple of messages that were meant to be debug and are
causing much confusion
- ensure the hotplug interrupt is disabled on Cedartrail systems.
- fix a bug where gtt roll mode called psbfb_sync, which tries to sync
the 2D engine. On other devices it is harmless as the 2D engine is
present but not in use when in gtt roll mode, on Cedartrail it causes
a hang
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
With branch stack sampling, it is possible to filter by priv levels.
In system-wide mode, that means it is possible to capture only user
level branches. The builtin SW LBR filter needs to disassemble code
based on LBR captured addresses. For that, it needs to know the task
the addresses are associated with. Because of context switches, the
content of the branch stack buffer may contain addresses from
different tasks.
We need a callback on context switch to either flush the branch stack
or save it. This patch adds a new callback in struct pmu which is called
during context switches. The callback is called only when necessary.
That is when a system-wide context has, at least, one event which
uses PERF_SAMPLE_BRANCH_STACK. The callback is never called for
per-thread context.
In this version, the Intel x86 code simply flushes (resets) the LBR
on context switches (fills it with zeroes). Those zeroed branches are
then filtered out by the SW filter.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-11-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds an internal sofware filter to complement
the (optional) LBR hardware filter.
The software filter is necessary:
- as a substitute when there is no HW LBR filter (e.g., Atom, Core)
- to complement HW LBR filter in case of errata (e.g., Nehalem/Westmere)
- to provide finer grain filtering (e.g., all processors)
Sometimes the LBR HW filter cannot distinguish between two types
of branches. For instance, to capture syscall as CALLS, it is necessary
to enable the LBR_FAR filter which will also capture JMP instructions.
Thus, a second pass is necessary to filter those out, this is what the
SW filter can do.
The SW filter is built on top of the internal x86 disassembler. It
is a best effort filter especially for user level code. It is subject
to the availability of the text page of the program.
The SW filter is enabled on all Intel processors. It is bypassed
when the user is capturing all branches at all priv levels.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-9-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements PERF_SAMPLE_BRANCH support for Intel
x86processors. It connects PERF_SAMPLE_BRANCH to the actual LBR.
The patch adds the hooks in the PMU irq handler to save the LBR
on counter overflow for both regular and PEBS modes.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-8-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch adds a restriction for Intel Atom LBR support. Only
steppings 10 (PineView) and more recent are supported. Older models
do not have a functional LBR. Their LBR does not freeze on PMU
interrupt which makes LBR unusable in the context of perf_events.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-7-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the mappings from the generic PERF_SAMPLE_BRANCH_*
filters to the actual Intel x86LBR filters, whenever they exist.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-6-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If precise sampling is enabled on Intel x86 then perf_event uses PEBS.
To correct for the off-by-one error of PEBS, perf_event uses LBR when
precise_sample > 1.
On Intel x86 PERF_SAMPLE_BRANCH_STACK is implemented using LBR,
therefore both features must be coordinated as they may not
configure LBR the same way.
For PEBS, LBR needs to capture all branches at the priv level of
the associated event.
This patch checks that the branch type and priv level of BRANCH_STACK
is compatible with that of the PEBS LBR requirement, thereby allowing:
$ perf record -b any,u -e instructions:upp ....
But:
$ perf record -b any_call,u -e instructions:upp
Is not possible.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-5-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Intel LBR on some recent processor is capable
of filtering branches by type. The filter is configurable
via the LBR_SELECT MSR register.
There are limitation on how this register can be used.
On Nehalem/Westmere, the LBR_SELECT is shared by the two HT threads
when HT is on. It is private to each core when HT is off.
On SandyBridge, the LBR_SELECT register is private to each thread
when HT is on. It is private to each core when HT is off.
The kernel must manage the sharing of LBR_SELECT. It allows
multiple users on the same logical CPU to use LBR_SELECT as
long as they program it with the same value. Across sibling
CPUs (HT threads), the same restriction applies on NHM/WSM.
This patch implements this sharing logic by leveraging the
mechanism put in place for managing the offcore_response
shared MSR.
We modify __intel_shared_reg_get_constraints() to cause
x86_get_event_constraint() to be called because LBR may
be associated with events that may be counter constrained.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-4-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the LBR definitions for NHM/WSM/SNB and Core.
It also adds the definitions for the architected LBR MSR:
LBR_SELECT, LBRT_TOS.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the ability to sample taken branches to the
perf_event interface.
The ability to capture taken branches is very useful for all
sorts of analysis. For instance, basic block profiling, call
counts, statistical call graph.
This new capability requires hardware assist and as such may
not be available on all HW platforms. On Intel x86 it is
implemented on top of the Last Branch Record (LBR) facility.
To enable taken branches sampling, the PERF_SAMPLE_BRANCH_STACK
bit must be set in attr->sample_type.
Sampled taken branches may be filtered by type and/or priv
levels.
The patch adds a new field, called branch_sample_type, to the
perf_event_attr structure. It contains a bitmask of filters
to apply to the sampled taken branches.
Filters may be implemented in HW. If the HW filter does not exist
or is not good enough, some arch may also implement a SW filter.
The following generic filters are currently defined:
- PERF_SAMPLE_USER
only branches whose targets are at the user level
- PERF_SAMPLE_KERNEL
only branches whose targets are at the kernel level
- PERF_SAMPLE_HV
only branches whose targets are at the hypervisor level
- PERF_SAMPLE_ANY
any type of branches (subject to priv levels filters)
- PERF_SAMPLE_ANY_CALL
any call branches (may incl. syscall on some arch)
- PERF_SAMPLE_ANY_RET
any return branches (may incl. syscall returns on some arch)
- PERF_SAMPLE_IND_CALL
indirect call branches
Obviously filter may be combined. The priv level bits are optional.
If not provided, the priv level of the associated event are used. It
is possible to collect branches at a priv level different from the
associated event. Use of kernel, hv priv levels is subject to permissions
and availability (hv).
The number of taken branch records present in each sample may vary based
on HW, the type of sampled branches, the executed code. Therefore
each sample contains the number of taken branches it contains.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1328826068-11713-2-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The driver already defines control "Multi Track Rate Locking" which
locks the card at current rate if switched to internal clock. This patch
limits the runtime rates to this rate only, allowing proper reporting
of the card capabilities, and e.g. automatic rate conversion by the plug
plugin to the currently locked rate.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a flag to indicate we initiated a recovery work
on purpose, in order to avoid triggering BUG() (when
the bug_on_recovery module param was set).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
