After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
His email address keeps bouncing, and he's not interested in mac80211
patches etc. anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of !CONFIG_X86_WP_WORKS_OK, __put_user_size_ex() is not defined.
Add macros for !CONFIG_X86_WP_WORKS_OK case.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xapic fix for 32bit platform with less than 8 cpu's.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
as per https://bugs.launchpad.net/bugs/294391. These got one sample of
each iPod generation going. However there still occurred I/O stalls
with the 3rd generation iPod which remain undiagnosed at the time of
this writing.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
According to https://bugs.launchpad.net/bugs/294391
- 3rd generation iPods need the "fix capacity" workaround after all
(apparently they crash after the last sector was accessed),
- 2nd generation iPods need the "128 kB maximum request size"
workaround.
Alas both iPod generations feature the same model ID in the config ROM,
hence we can only define a shared quirks list entry for them. Luckily
the fix capacity workaround did not show a negative effect in Jarod's
tests with 2nd gen. iPod.
A side note: Apple computers in target mode (or at least an x86 Mac
mini) don't have firmware_version and model_id, hence none of the iPod
quirks list entries is active for them.
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.
It's hard to tell where this change was introduced since this file
has been moved and merged.
While this fix prevents a crash, suspend on my n810 is broken with
current kernels. I never come out of suspend.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By Ingo Molnar, interrupts are not masked by default.
(refer to 76d2160147)
But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Reviewed-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This has similar symptoms than 66c23551b1
where just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch
can cause incorrect dump_stack(). Here it can happen if channel has been
used before and the channel flags variable holds old status.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CSR must be cleared before invoking the callback.
If the callback function starts a new, fast DMA transfer on the same
channel, the completion status might lost if CSR is cleared after
the callback invocation.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 5a611268b6.
It is causing occasional boot crashes, caused by certain
linker versions (GNU ld version 2.18.50.0.6-2 20080403) messing up:
82dcc000 D __per_cpu_load
c16e6000 A __per_cpu_load_abs
The __per_cpu_load value is out of whack. Hpa noticed the following
detail:
* (gdb) p/x -(0xc16e6000-0x82dcc000)
* $2 = 0xc16e6000
* I.e. one is the other << 1
The two symbols should be equal.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the case of having a selector instead of mixer while initing input
sources, the case that happens with ALC889, we must select instead
of muting input. Problem was found while testing with hda-emu.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: widen debug checks
VirtualBox calls do_page_fault() from an atomic context but runs into a
might_sleep() way pas this point, cure that.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This UBIFS feature has never worked properly, and it was a mistake
to add it because we simply have no use-cases. So, lets still accept
the fast_unmount mount option, but ignore it. This does not change
much, because UBIFS commit in sync_fs anyway, and sync_fs is called
while unmounting.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When mounting/re-mounting, UBIFS returns EINVAL even if the ENOSPC
or EROFS codes are are much better, just because we have not found
references to ENOSPC/EROFS in mount (2) man pages. This patch
changes this behaviour and makes UBIFS return real error code,
because:
1. It is just less confusing and more logical
2. mount is not described in SuSv3, so it seems to be not really
well-standartized
3. we do not cover all cases, and any random undocumented in man
pages error code may be returned anyway
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
- preserve the idx_gc list - it will be needed in the same
state, should UBIFS be remounted rw again
- prevent remounting ro if we have switched to read only
mode (due to a fatal error)
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
All writes go through wbufs so they must be sync'd
after syncing inodes and pages.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds the analog loopback/bypass support for twl4030 codec.
Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.
The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.
When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.
When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.
In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dma ops unification enables X86 and IA64 to share intel_dma_ops so
we can make dma mapping functions static. This also remove unused
intel_map_single().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dma_mapping_error is used to see if dma_map_single and dma_map_page
succeed. IA64 VT-d dma_mapping_error always says that dma_map_single
is successful even though it could fail. Note that X86 VT-d works
properly in this regard.
This patch fixes IA64 VT-d dma_mapping_error by adding VT-d's own
dma_mapping_error() that works for both X86_64 and IA64. VT-d uses
zero as an error dma address so VT-d's dma_mapping_error returns 1 if
a passed dma address is zero (as x86's VT-d dma_mapping_error does
now).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before the dma ops unification, IA64 always uses GFP_DMA for
dma_alloc_coherent like:
#define dma_alloc_coherent(dev, size, handle, gfp) \
platform_dma_alloc_coherent(dev, size, handle, (gfp) | GFP_DMA)
This GFP_DMA enforcement doesn't make sense for IOMMUs since they can
do address translation to give addresses that devices can access
to. The IOMMU drivers ignore the zone flag. However, this is still
necessary for swiotlb since it can't do address translation.
We don't always need to use GFP_DMA for swiotlb. We need GFP_DMA for
devices incapable of 64bit DMA.
This patch is sorta updated version of:
http://marc.info/?l=linux-kernel&m=122638215612705&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
We may use macros from processor-flags.h instead
of hardcoding bits. Actually it's not direct mapping
of old instructions with new ones -- BTS does change
CF flag while MOV does not. But i didn't find any
dependency on CF in this code.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Use tracing_reset_online_cpus instead of open coding it.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
don't kfree in use counters.
Running...
while true; do perfstat -e 1 -c true; done
...on all cores for a while doesn't seem to be eating ram, and my oops
is gone.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.
This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f859 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move X86_VSMP out of the subarch menu - this way it can be enabled
together with standard PC support as well, in the same kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- make X86_GENERICARCH depend X86_NON_STANDARD
- move X86_SUMMIT, X86_ES7000 and X86_BIGSMP out of the subarchitecture
menu and under this option
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move X86_ELAN (old, NCR hw platform built on Intel CPUs) from the
subarchitecture menu to the non-standard-platform section.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move X86_ELAN (old, AMD based web-boxes) from the subarchitecture
menu to the non-standard-platform section.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Voyager has this ISA quirk (because Voyager has no ISA support):
config ISA
bool "ISA support"
depends on !X86_VOYAGER
There's a ton of x86 hardware that does not support ISA, and because
most ISA drivers cannot auto-detect in a safe way, the convention in
the kernel has always been to not enable ISA drivers if they are not
needed.
Voyager users can do likewise - no need for a Kconfig quirk.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Voyager has this PM/ACPI Kconfig quirk:
menu "Power management and ACPI options"
depends on !X86_VOYAGER
Most of the PM features are auto-detect so they should be safe to run
on just about any hardware. (If not, those instances need fixing.)
In any case, if a kernel is built for Voyager, the power management
options can be disabled.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Voyager has this Kconfig quirk:
config HOTPLUG_CPU
bool "Support for hot-pluggable CPUs"
depends on SMP && HOTPLUG && !X86_VOYAGER
But this exception will be moot once Voyager starts using the
generic x86 code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If no MCE code is desired on Voyager hw then the solution
is to turn them off in the .config - and to extend the MCE
code to not initialize on Voyager.
Remove the build-time quirk.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The lapic/ioapic code properly auto-detects and is safe to run on CPUs that
have no local APIC. (or which have their lapic turned off in the hardware)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove this Kconfig quirk:
config PARAVIRT
bool "Enable paravirtualization code"
depends on !X86_VOYAGER
help
Voyager support built into a kernel does not preclude paravirt support.
Signed-off-by: Ingo Molnar <mingo@elte.hu>