QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This commit makes sure the drivers for the Armada 7K/8K pin controllers
are enabled.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
CRIU restores application mappings on the same place where they
were before Checkpoint. That means, that we need to move vDSO
and sigpage during restore on exactly the same place where
they were before C/R.
Make mremap() code update mm->context.{sigpage,vdso} pointers
during VMA move. Sigpage is used for landing after handling
a signal - if the pointer is not updated during moving, the
application might crash on any signal after mremap().
vDSO pointer on ARM32 is used only for setting auxv at this moment,
update it during mremap() in case of future usage.
Without those updates, current work of CRIU on ARM32 is not reliable.
Historically, we error Checkpointing if we find vDSO page on ARM32
and suggest user to disable CONFIG_VDSO.
But that's not correct - it goes from x86 where signal processing
is ended in vDSO blob. For arm32 it's sigpage, which is not disabled
with `CONFIG_VDSO=n'.
Looks like C/R was working by luck - because userspace on ARM32 at
this moment always sets SA_RESTORER.
Signed-off-by: Dmitry Safonov <dsafonov@virtuozzo.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch fixes the checkpatch.pl warnings on the driver
file.
Signed-off-by: Aravind Thokala <aravind.thk@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes this WARNING
sound/soc/sh/rcar/ssi.c:285:5-14: WARNING: Unsigned expression\
compared with zero: main_rate < 0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation of device tree bindings for the
STM32 SPDIFRX interface.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of spi_alloc_master() failure it is better to return the
error immediately, so move the error check right after the allocation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It doesn't use asm header. We can add COMPILE_TEST
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since trace_clock is in a different file and already marked with notrace,
enable tracing in time.c by removing it from the disabled list in Makefile.
Also annotate clocksource read functions and sched_clock with notrace.
Testing: Timer and ftrace selftests run with different trace clocks.
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the event for which an AUX area is about to be allocated, does
not support setting up an AUX area, rb_alloc_aux() return -ENOTSUPP.
This error condition is being returned unfiltered to the user space,
and, for example, the perf tools fails with:
failed to mmap with 524 (INTERNAL ERROR: strerror_r(524, 0x3fff497a1c8, 512)=22)
This error can be easily seen with "perf record -m 128,256 -e cpu-clock".
The 524 error code maps to -ENOTSUPP (in rb_alloc_aux()). The -ENOTSUPP
error code shall be only used within the kernel. So the correct error
code would then be -EOPNOTSUPP.
With this commit, the perf tool then reports:
failed to mmap with 95 (Operation not supported)
which is more clear.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Hou <bjhoupu@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Cc: acme@kernel.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/1497954399-6355-1-git-send-email-brueckner@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add Google Rose Touchpad USB PID and required quirks.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CMA has gained a recent helper function for calculating the start
of the plane buffer's physical address. Use that instead of the
hand rolled version.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The component-based encoder(s) used by HDLCD expect the CRTC port
to be set before binding in order to find the right endpoint.
Without this patch, the TDA19988 encoder driver prints a warning
"Falling back to first CRTC".
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Support PTP Stick and Touchpad device. This Touchpad is Precision Touchpad
(PTP), and Stick Pointer data is the same as Mouse; Stick Pointer works as
Mouse.
[jkosina@suse.cz: changelog deuglification]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Except ALC269.
This will reduce pop noise from headset or headphone.
If codec enter to power save state, when plug headset or headphone....
It has a chance to cut off power by system.
Our new codec use this procedure will be more stable during suspend
and resume state.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Propagate errnos for late probe errors (e.g. -ENOMEM on allocation
failures) instead of always returning -EIO.
Note that some drivers are currently returning -ENODEV from their attach
callbacks when a device is not supported, but this has also been mapped
to -EIO.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the probe callback more readable by refactoring the port
endpoint-resource setup by adding four helper functions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add driver for lp87565 PMIC family GPIOs. Three GPIOs are supported
and can be configured in Open-drain output or Push-pull output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dwapb_irq_set_type overwrites polarity register value for
IRQ_TYPE_EDGE_BOTH case. If the polarity of one gpio is 0
by default, then it will set falling edge irq trigger.
and the gpio may requires rising edge irq for the first time,
and it will be missed.
Do not overwrite polarity register for IRQ_TYPE_EDGE_BOTH case
can solve this issue.
Signed-off-by: Xiaoguang Chen <xgchenshy@gmail.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
[Fix some really weird text encoding problem]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SCIF1 and SCIF2 pin groups to the R8A7792 PFC driver.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In
commit 91eefc05f0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Dec 14 00:08:10 2016 +0100
drm: Tighten locking in drm_mode_getconnector
I reordered the logic a bit in that IOCTL, but that broke userspace
since it'll get the new mode list, but not the new property values.
Fix that again.
v2: Fix up the error path handling when copy_to_user for the modes
failes (Dhinakaran).
Fixes: 91eefc05f0 ("drm: Tighten locking in drm_mode_getconnector")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Tested-by: "H.J. Lu" <hjl.tools@gmail.com>
Cc: <stable@vger.kernel.org> # v4.11+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100576
Cc: "H.J. Lu" <hjl.tools@gmail.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620202837.1701-1-daniel.vetter@ffwll.ch
Merge time(keeping) updates from John Stultz:
"Just a small set of changes, the biggest changes being the MONOTONIC_RAW
handling cleanup, and a new kselftest from Miroslav. Also a a clear
warning deprecating CONFIG_GENERIC_TIME_VSYSCALL_OLD, which affects ppc
and ia64."
As for slb_miss_realmode(), rename slb_allocate_realmode() to avoid
confusion over whether it runs in real or virtual mode - it runs in
both.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
slb_miss_realmode() doesn't always runs in real mode, which is what the
name implies. So rename it to avoid confusing people.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
All the callers of slb_miss_realmode currently open code the #ifndef
CONFIG_RELOCATABLE check and the branch via CTR in the RELOCATABLE case.
We have a macro to do this, BRANCH_TO_COMMON(), so use it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
This test checks the response of the system clock to frequency
steps made with adjtimex(). The frequency error and stability of
the CLOCK_MONOTONIC clock relative to the CLOCK_MONOTONIC_RAW clock
is measured in two intervals following the step. The test fails if
values from the second interval exceed specified limits.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
When the first timestamp in the list of clock readings was later than
the second timestamp and all other timestamps were in order, the
inconsistency was not reported because the index of the out-of-order
timestamp was equal to the default value.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
CONFIG_GENERIC_TIME_VSYSCALL_OLD was introduced five years ago
to allow a transition from the old vsyscall implementations to
the new method (which simplified internal accounting and made
timekeeping more precise).
However, PPC and IA64 have yet to make the transition, despite
in some cases me sending test patches to try to help it along.
http://patches.linaro.org/patch/30501/http://patches.linaro.org/patch/35412/
If its helpful, my last pass at the patches can be found here:
https://git.linaro.org/people/john.stultz/linux.git dev/oldvsyscall-cleanup
So I think its time to set a deadline and make it clear this
is going away. So this patch adds warnings about this
functionality being dropped. Likely to be in v4.15.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that we fixed the sub-ns handling for CLOCK_MONOTONIC_RAW,
remove the duplicitive tk->raw_time.tv_nsec, which can be
stored in tk->tkr_raw.xtime_nsec (similarly to how its handled
for monotonic time).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Mentz <danielmentz@google.com>
Tested-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
'rc' is known to be 0 at this point. So if 'init_sg' or 'kzalloc' fails, we
should return -ENOMEM instead.
Also remove a useless 'rc' in a debug message as it is meaningless here.
Fixes: 026e93dc0a ("CIFS: Encrypt SMB3 requests before sending")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
It will be used in arch/powerpc/kvm/book3s_hv.c KVM module.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A queue must be frozen while the mapped state of a hardware queue
is changed. Additionally, any change of the mapped state is
followed by a call to blk_mq_map_swqueue() (see also
blk_mq_init_allocated_queue() and blk_mq_update_nr_hw_queues()).
Since blk_mq_map_swqueue() does not map any unmapped hardware
queue onto any software queue, no attempt will be made to run
an unmapped hardware queue. Hence issue a warning upon attempts
to run an unmapped hardware queue.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The variable 'disk_type' is never modified so constify it.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Document the locking assumptions in functions that modify
blk_mq_ctx.rq_list to make it easier for humans to verify
this code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some functions in block/blk-core.c must only be used on blk-sq queues
while others are safe to use against any queue type. Document which
functions are intended for blk-sq queues and issue a warning if the
blk-sq API is misused. This does not only help block driver authors
but will also make it easier to remove the blk-sq code once that code
is declared obsolete.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of documenting the locking assumptions of most block layer
functions as a comment, use lockdep_assert_held() to verify locking
assumptions at runtime.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a comment above the queue_lockdep_assert_held() macro that
explains the purpose of the q->queue_lock test.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Initialization of blk-mq requests is a bit weird: blk_mq_rq_ctx_init()
is called after a value has been assigned to .rq_flags and .rq_flags
is initialized in __blk_mq_finish_request(). Initialize .rq_flags in
blk_mq_rq_ctx_init() instead of relying on __blk_mq_finish_request().
Moving the initialization of .rq_flags is fine because all changes
and tests of .rq_flags occur between blk_get_request() and finishing
a request.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since scsi_req_init() works on a struct scsi_request, change the
argument type into struct scsi_request *.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
