Revert commit 39b64aa1c0 (cpufreq: schedutil: Reduce frequencies
slower) that introduced unintentional changes in behavior leading
to adverse effects on some systems.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Considering this case:
1. A program opens a sysfs table file 65535 times, it can increase
validation_count and first increment cause the table to be mapped:
validation_count = 65535
2. AML execution causes "Load" to be executed on the same
table, this time it cannot increase validation_count, so
validation_count remains:
validation_count = 65535
3. The program closes sysfs table file 65535 times, it can decrease
validation_count and the last decrement cause the table to be
unmapped:
validation_count = 0
4. AML code still accessing the loaded table, kernel crash can be
observed.
To prevent that from happening, add a validation_count threashold.
When it is reached, the validation_count can no longer be
incremented/decremented to invalidate the table descriptor (means
preventing table unmappings)
Note that code added in acpi_tb_put_table() is actually a no-op but
changes the warning message into a "warn once" one. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.
This fixes that to check minimal required PVINFO version instead.
v2:
- drop unneeded version macro
- use only major version for sanity check
v3:
- fix up PVInfo value with kernel type
- one indent fix
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609074805.5101-1-zhenyuw@linux.intel.com
Whilst debugging a remote crash, I noticed that show_pte is unhelpful
when it comes to describing the structure of the page table being walked.
This is easily fixed by printing out the page table (swapper vs user),
page size and virtual address size when displaying the PGD address.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Print out the name of the file associated with the vma that faulted.
This is usually the executable or shared library name. We already print
out the task name, but also printing the library name is useful for
pinpointing bugs to libraries.
Also print the base address and size of the vma, which together with the
PC (printed by __show_regs) gives the offset into the library.
Fault prints now look like:
test[2361]: unhandled level 2 translation fault (11) at 0x00000012, esr 0x92000006, in libfoo.so[ffffa0145000+1000]
This is already done on x86, for more details see commit 03252919b7
("x86: print which shared library/executable faulted in segfault etc.
messages v3").
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When we take a fault from EL0 that can't be handled, we print out the
page table entries associated with the faulting address. This allows
userspace to print out any current page table entries, including kernel
(TTBR1) entries. Exposing kernel mappings like this could pose a
security risk, so don't print out page table information on EL0 faults.
(But still print it out for EL1 faults.) This also follows the same
behaviour as x86, printing out page table entries on kernel mode faults
but not user mode faults.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When we take a fault that can't be handled, we print out the page table
entries associated with the faulting address. In some cases we currently
print out the wrong entries. For a faulting TTBR1 address, we sometimes
print out TTBR0 table entries instead, and for a faulting TTBR0 address
we sometimes print out TTBR1 table entries. Fix this by choosing the
tables based on the faulting address.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[will: zero-extend addrs to 64-bit, don't walk swapper w/ TTBR0 addr]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The GPU has two functional clocks - GPU_CORE_GCLK and GPU_HYD_GCLK.
Both of these are mux clocks and are derived from the DPLL_CORE
H14 output clock CORE_GPU_CLK by default. These clocks can also be
be derived from DPLL_PER or DPLL_GPU.
The GPU DPLL provides the output clocks primarily for the GPU.
Configuring the GPU for different OPP clock frequencies is easier
to achieve when using the DPLL_GPU rather than the other two DPLLs
due to:
1. minimal affect on any other output clocks from these DPLLs
2. may require an impossible post-divider values on existing DPLLs
without affecting other clocks.
So, switch the GPU functional clocks to be sourced from GPU DPLL by
default. This is done using the DT standard properties "assigned-clocks"
and "assigned-clock-parents". Newer u-boots (from 2017.01 onwards) reuse
and can update these properties to choose an appropriate one-time fixed
OPP configuration as all the required ABB/AVS setup is performed within
the bootloader. Note that there is no DVFS supported for any of the
non-MPU domains. The DPLL will automatically transition into a low-power
stop mode when the associated output clocks are not utilized or gated
automatically.
This patch also sets the initial values for the DPLL_GPU outputs.
These values are chosen based on the OPP_NOM values defined as per
recommendation from design team. The DPLL locked frequency is kept
at 1277 MHz, so that the value for the divider clock, dpll_gpu_m2_ck,
can be set to 425.67 MHz for OPP_NOM.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
[s-anna@ti.com: revise patch description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL in DRA7xx provides the output clocks for only the IVAHD
subsystem in DRA7xx as compared to previous OMAP generations when it
provided the clocks for both DSP and IVAHD subsystems. This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
IVA DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The reset value of the divider M2 (that supplies the IVA_GFLCK, the
functional clock for the IVAHD subsystem) does not match a specific
OPP. So, the derived output clock from this IVA DPLL has to be
initialized as well to avoid initializing these divider outputs to an
incorrect frequencies.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 2300 MHz, so
the dpll_iva_ck clock rate used is half of this value. The value for the
divider clock, dpll_iva_m2_ck, has to be set to 388.333334 MHz or more
for the divider clk logic to compute the appropriate divider value for
OPP_NOM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP DPLL is a new DPLL compared to previous OMAP generations and
supplies the root clocks for the DSP processors, as well as a mux
input source for EVE sub-system (on applicable SoCs). This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
DSP DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The DSP DPLL provides two output clocks, DSP_GFCLK and EVE_GCLK. The
desired rate for DSP_GFCLK is 600 MHz (same as DSP DPLL CLKOUT frequency),
and is currently auto set due to the desired M2 divider value being the
same as reset value for the locked frequency of 600 MHz. The EVE_GCLK
however is required to be 400 MHz, so set the dpll_dsp_m3x2_ck's rate
explicitly so that the divider is set properly. The dpll_dsp_m2_ck rate
is also set explicitly to not rely on any implicit matching divider reset
values to the locked DPLL frequency.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 1200 MHz, so
the dpll_dsp_ck clock rate used is half of this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU1 functional clock is actually the output of a mux clock,
ipu1_gfclk_mux. The mux clock is sourced by default from the
DPLL_ABE_X2_CLK, and this results in a rather odd clock frequency
(361 MHz) for the IPU1 functional clock on platforms where ABE_DPLL
is configured properly. Reconfigure the mux clock to be sourced from
CORE_IPU_ISS_BOOST_CLK (dpll_core_h22x2_ck), so that both the IPU1
and IPU2 are running from the same clock and clocked at the same
nominal frequency of 425 MHz.
This also ensures that IPU1 functional clock is always configured
properly and becomes independent of the state of the ABE DPLL on
all boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers H11 & H12 (functional clocks for DSP
and IVAHD respectively) are identical to each other, but are different
at each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP_NOM values as defined in
the OMAP5432 SR2.0 Data Manual Book vK, section 5.2.3.5 "DPLL_IVA
Preferred Settings". The recommended maximum DPLL locked frequency is
2330 MHz for OPP_NOM (value for DPLL_IVA_X2_CLK), so the dpll_iva_ck
clock rate used is half of this value. The value 465.92 MHz is used
instead of 465.9 MHz for dpll_iva_h11x2_ck so that proper divider
value can be calculated.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers M4 & M5 (functional clocks for DSP and
IVAHD respectively) are identical to each other, but are different at
each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP100 values as defined in the
OMAP4430 ES2.x Public TRM vAP, section "3.6.3.8.7 DPLL_IVA Preferred
Settings". The DPLL locked frequency is 1862.4 MHz (value for
DPLL_IVA_X2_CLK), so the dpll_iva_ck clock rate used is half of
this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Document board part number and compatible values for the version with
R-Car H3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The board part numbers for the R-Car H3 and M3 ULCB boards corresponded
to versions predating mass production. Update them for mass production.
Note that the H3 ULCB board can be equipped with either revision ES1.1
or ES2.0 of the R-Car H3 SoC. While these have different board part
numbers, no new compatible values are needed, as the revision can be
detected at runtime using the PRR register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document the iW-RainboW-G20D-Qseven-RZG1M device tree bindings,
listing it as a supported board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document the iW-RainboW-G20M-Qseven-RZG1M device tree bindings,
listing it as a supported system on module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now we will force to do garbage collection if any policy removed in
xfrm_policy_flush(). But during xfrm_net_exit(). We call flow_cache_fini()
first and set set fc->percpu to NULL. Then after we call xfrm_policy_fini()
-> frxm_policy_flush() -> flow_cache_flush(), we will get NULL pointer
dereference when check percpu_empty. The code path looks like:
flow_cache_fini()
- fc->percpu = NULL
xfrm_policy_fini()
- xfrm_policy_flush()
- xfrm_garbage_collect()
- flow_cache_flush()
- flow_cache_percpu_empty()
- fcp = per_cpu_ptr(fc->percpu, cpu)
To reproduce, just add ipsec in netns and then remove the netns.
v2:
As Xin Long suggested, since only two other places need to call it. move
xfrm_garbage_collect() outside xfrm_policy_flush().
v3:
Fix subject mismatch after v2 fix.
Fixes: 35db069121 ("xfrm: do the garbage collection after flushing policy")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The goals are to:
- Allow precise control over and automatic selection of which
(sub)drivers are used for which SoC,
- Allow adding support for new SoCs easily,
- Allow compile-testing of all (sub)drivers,
- Keep driver selection logic in the subsystem-specific Kconfig,
independent from the architecture-specific Kconfig (i.e. no "select"
from arch/arm64/Kconfig.platforms), to avoid dependencies.
This is implemented by:
- Introducing Kconfig symbols for all drivers and sub-drivers,
- Introducing the Kconfig symbol SOC_RENESAS, which is enabled
automatically when building for a Renesas ARM platform, and which
enables all required drivers without interaction of the user, based
on SoC-specific ARCH_* symbols,
- Allowing the user to enable any Kconfig symbol manually if
COMPILE_TEST is enabled,
- Using the new Kconfig symbols instead of the ARCH_* symbols to
control compilation in the Makefile,
- Always entering drivers/soc/renesas/ during the build.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car H3 ES2.0 SiP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Add initial support for the common parts of the Salvator-XS board into
its own .dtsi file, to be included by the DTSes for the H3/M3-W
versions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-X and Salvator-XS (Salvator-X 2nd version) boards
are very similar. To avoid duplication, prepare for the advent of the
latter by extracting the common board parts into its own .dtsi file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs contain multiple PWM modules. Hence to avoid conflicts,
pinctrl subnodes for PWM should include indices referring to their
instances.
Fixes: b33be33670 ("arm64: dts: salvator-x: Add panel backlight support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Split off support for H3ULCB boards with the ES1.x revision of the R-Car
H3 SoC into a separate file. The main r8a7795-h3ulcb.dts file now
corresponds to H3ULCB with R-Car H3 ES2.0 or later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RZG1M Qseven System On Module.
http://www.iwavesystems.com/rz-g1m-qseven-module.html
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree source for Renesas GR-Peach board.
GR-Peach is an RZ/A1H based board with 10MB of on-chip SRAM and 8MB
QSPI flash storage.
Add support for the board, and create a 2MB partition to use as rootfs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
After discussing it, this feature is dropped as it is not considered
adequate:
https://patchwork.kernel.org/patch/9639317/
There is no user of this macro yet, so there is no impact on the drivers.
This reverts commit 376bc27150.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The recent changes made the fttmr010 to be more generic and support different
timers with a very few differences like moxart or aspeed.
The aspeed timer uses a countdown and there is a test against the aspeed2400
compatible string to set a flag.
With the previous patch, we added the aspeed2500 compatible string but without
taking care of setting the countdown flag.
Fix this by specifiying a init function and pass the aspeed flag to a common
init function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Also clean up space-before-tab issues in the documentation.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This merges the Moxa Art timer driver into the Faraday FTTMR010
driver and replaces all Kconfig symbols to use the Faraday
driver instead. We are now so similar that the drivers can
be merged by just adding a few lines to the Faraday timer.
Differences:
- The Faraday driver explicitly sets the counter to count
upwards for the clocksource, removing the need for the
clocksource core to invert the value.
- The Faraday driver also handles sched_clock()
On the Aspeed, the counter can only count downwards, so support
the timers in downward-counting mode as well, and flag the
Aspeed to use this mode. This mode was tested on the Gemini so
I have high hopes that it'll work fine on the Aspeed as well.
After this we have one driver for all three SoCs and a generic
Faraday FTTMR010 timer driver, which is nice.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This switches the clocksource to TIMER2 like the Moxart driver
does. Mainly to make it more similar to the Moxart/Aspeed driver
but also because it seems more neat to use the timers in order:
use timer 1, then timer 2.
Cc: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This switches the drivers to use the bitops BIT() macro
to define bits.
Cc: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This converts the Faraday FTTMR010 to use the state container
design pattern. Take some care to handle the state container
and free:ing of resources as has been done in the Moxa driver.
Cc: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Gemini now has a proper clock driver and a proper PCLK
assigned in its device tree. Drop the Gemini-specific hacks
to look up the system speed and rely on the clock framework
like everyone else.
Cc: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This merges the Moxa and FTTMR010 device tree bindings into the
Faraday binding document to avoid confusion.
The FTTMR010 is the IP block used by these SoCs, in vanilla
or modified variant.
The Aspeed variant is modified such that it is no longer fully
register-compatible with FTTMR010 so for this reason it is not
listed with two compatible strings, instead just one.
Cc: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We need to also prepare and enable the clock we are using to get
the right reference count and avoid it being shut off.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The merging of a number of clocksource drivers into fttmr010 means we
require clock-names to be specified in the Aspeed timer node, else the
clocksource fails to probe and boot hangs.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
