We recently shifted this code around, so we're no longer holding the
lock on this path.
Fixes: 755b5bc681 ("fsnotify: Remove indirection from mark list addition")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ARTPEC6
drivers/pinctrl/Kconfig: bool "Axis ARTPEC-6 pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Lars Persson <lars.persson@axis.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: linux-arm-kernel@axis.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use temporary mapping for memory copying operations.
To avoid any sleeping problem,
mark_inode_dirty(inode) was moved after kunmap() in
udf_adinicb_readpage()
down_write(&iinfo->i_data_sem) set before kmap_atomic()
in udf_expand_file_adinicb()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
According to commit f90774e1fd ("checkpatch: look for symbolic
permissions and suggest octal instead")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
powerpc expects IRQs to already be (soft) disabled when switch_mm() is
called, as made clear in the commit message of 9c1e105238 ("powerpc: Allow
perf_counters to access user memory at interrupt time").
Aside from any race conditions that might exist between switch_mm() and an IRQ,
there is also an unconditional hard_irq_disable() in switch_slb(). If that isn't
followed at some point by an IRQ enable then interrupts will remain disabled
until we return to userspace.
It is true that when switch_mm() is called from the scheduler IRQs are off, but
not when it's called by use_mm(). Looking closer we see that last year in commit
f98db6013c ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler")
this was made more explicit by the addition of switch_mm_irqs_off() which is now
called by the scheduler, vs switch_mm() which is used by use_mm().
Arguably it is a bug in use_mm() to call switch_mm() in a different context than
it expects, but fixing that will take time.
This was discovered recently when vhost started throwing warnings such as:
BUG: sleeping function called from invalid context at kernel/mutex.c:578
in_atomic(): 0, irqs_disabled(): 1, pid: 10768, name: vhost-10760
no locks held by vhost-10760/10768.
irq event stamp: 10
hardirqs last enabled at (9): _raw_spin_unlock_irq+0x40/0x80
hardirqs last disabled at (10): switch_slb+0x2e4/0x490
softirqs last enabled at (0): copy_process+0x5e8/0x1260
softirqs last disabled at (0): (null)
Call Trace:
show_stack+0x88/0x390 (unreliable)
dump_stack+0x30/0x44
__might_sleep+0x1c4/0x2d0
mutex_lock_nested+0x74/0x5c0
cgroup_attach_task_all+0x5c/0x180
vhost_attach_cgroups_work+0x58/0x80 [vhost]
vhost_worker+0x24c/0x3d0 [vhost]
kthread+0xec/0x100
ret_from_kernel_thread+0x5c/0xd4
Prior to commit 04b96e5528 ("vhost: lockless enqueuing") (Aug 2016) the
vhost_worker() would do a spin_unlock_irq() not long after calling use_mm(),
which had the effect of reenabling IRQs. Since that commit removed the locking
in vhost_worker() the body of the vhost_worker() loop now runs with interrupts
off causing the warnings.
This patch addresses the problem by making the powerpc code mirror the x86 code,
ie. we disable interrupts in switch_mm(), and optimise the scheduler case by
defining switch_mm_irqs_off().
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Flesh out/rewrite change log, add stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For CPUs present at boot each logical CPU acquires a reference to the
associated device node of the core. This happens in register_cpu() which
is called by topology_init(). The result of this is that we end up with
a reference held by each thread of the core. However, these references
are never freed if the CPU core is DLPAR removed.
This patch fixes the reference leaks by acquiring and releasing the references
in the CPU hotplug callbacks un/register_cpu_online(). With this patch symmetric
reference counting is observed with both CPUs present at boot, and those DLPAR
added after boot.
Fixes: f86e4718f2 ("driver/core: cpu: initialize of_node in cpu's device struture")
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Historically struct device_node references were tracked using a kref embedded as
a struct field. Commit 75b57ecf9d ("of: Make device nodes kobjects so they
show up in sysfs") (Mar 2014) refactored device_nodes to be kobjects such that
the device tree could by more simply exposed to userspace using sysfs.
Commit 0829f6d1f6 ("of: device_node kobject lifecycle fixes") (Mar 2014)
followed up these changes to better control the kobject lifecycle and in
particular the referecne counting via of_node_get(), of_node_put(), and
of_node_init().
A result of this second commit was that it introduced an of_node_put() call when
a dynamic node is detached, in of_node_remove(), that removes the initial kobj
reference created by of_node_init().
Traditionally as the original dynamic device node user the pseries code had
assumed responsibilty for releasing this final reference in its platform
specific DLPAR detach code.
This patch fixes a refcount underflow introduced by commit 0829f6d1f6, and
recently exposed by the upstreaming of the recount API.
Messages like the following are no longer seen in the kernel log with this
patch following DLPAR remove operations of cpus and pci devices.
rpadlpar_io: slot PHB 72 removed
refcount_t: underflow; use-after-free.
------------[ cut here ]------------
WARNING: CPU: 5 PID: 3335 at lib/refcount.c:128 refcount_sub_and_test+0xf4/0x110
Fixes: 0829f6d1f6 ("of: device_node kobject lifecycle fixes")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
[mpe: Make change log commit references more verbose]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the code that dumps SLB entries uses a double-nested if. This
means the actual dumping logic is a bit squashed. Deindent it by using
continue.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although most of these kprobes patches are powerpc specific, there's a couple
that touch generic code (with Acks). At the moment there's one conflict with
acme's tree, but it's not too bad. Still just in case some other conflicts show
up, we've put these in a topic branch so another tree could merge some or all of
it if necessary.
The logic to check if the pin is an input or output whilst testing if we
need to read the register value from the hardware or not is currently
inverted. Remove the erroneous not from the if statement.
Fixes: 11598d1740 ("gpio: arizona: Correct handling for reading input GPIOs")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whiskey cove PMIC has three GPIO banks with total number of 13 GPIO
pins. But when checking for the pending status, for_each_set_bit() uses
bit width of 7 and hence it only checks the status for first 7 GPIO pins
missing to check/clear the status of rest of the GPIO pins. This patch
fixes this issue.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 67809b974a ("GPIO: gpio-dwapb: Change readl&writel to
dwapb_read&dwapb_write") missed this readl_relaxed() usage, I'm not
sure the reason, maybe for performance reason? But if we do care
the performance, we could use the relaxed io in dwapb_read and
dwapb_write.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g5 was performed on an AST2500EVB system,
using the strategy outlined in the commit message for the change to the
Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, using the strategy outlined in the commit message for the
change to the Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several pinconf parameters have a fairly straight-forward mapping onto
the Aspeed pin controller. These include management of pull-down bias,
drive-strength, and some debounce configuration.
Pin biasing largely is managed on a per-GPIO-bank basis, aside from the
ADC and RMII/RGMII pins. As the bias configuration for each pin in a
bank maps onto a single per-bank bit, configuration tables will be
introduced to describe the ranges of pins and the supported pinconf
parameter. The use of tables also helps with the sparse support of
pinconf properties, and the fact that not all GPIO banks support
biasing or drive-strength configuration.
Further, as the pin controller uses a consistent approach for bias and
drive strength configuration at the register level, a second table is
defined for looking up the the bit-state required to enable or query the
provided configuration.
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, and pinctrl-aspeed-g5 on an AST2500EVB as well as under QEMU.
The test method was to set the appropriate bits via devmem and verify
the result through the controller's pinconf-pins debugfs file. This
simultaneously validates the get() path and half of the set() path. The
remainder of the set() path was validated by configuring a handful of
pins via the devicetree with the supported pinconf properties and
verifying the appropriate registers were touched.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the datasheet, manage the IO and value states to implement
open-source/open-drain, but do this by falling back to gpiolib's
emulation.
This commit simply makes the behaviour explicit for clarity, rather than
relying on the implicit return of -ENOTSUPP to trigger the emulation.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each GPIO in the Aspeed GPIO controller can choose one of four input
debounce states: to disable debouncing for an input, or select from one
of three programmable debounce timer values. Each GPIO in a
four-bank-set is assigned one bit in each of two debounce configuration
registers dedicated to the set, and selects a debounce state by
configuring the two bits to select one of the four options.
The limitation on debounce timer values is managed by mapping offsets
onto a configured timer value and keeping count of the number of users
a timer has. Timer values are configured on a first-come-first-served
basis.
A small twist in the hardware design is that the debounce configuration
register numbering is reversed with respect to the binary representation
of the debounce timer of interest (i.e. debounce register 1 represents
bit 1, and debounce register 2 represents bit 0 of the timer numbering).
Tested on an AST2500EVB with additional inspection under QEMU's
romulus-bmc machine.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need a reference to the HPLL to calculate debounce cycles. If the
clocks property is not supplied in the GPIO node then the consumer
should deny any debounce requests.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When downscaling, mclk needs to be sufficiently higher than pxlclk in
order to be able to fetch the higher-resolution data and produce output
pixels. When not scaling, or when upscaling, mclk can be equal to
pxlclk. Since the driver doesn't control mclk, just ensure that the
requirement is satisfied with the current clock rate.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Apply image enhacement when we are upscaling by a factor of 2
or more in either direction.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
This patch which adds STM32F469 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove "ngpios" bindings definition as it is no more used in stm32 pinctrl
driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl has to be registered earlier. Mainly to register bank irqdomain
earlier as other devices could use interrupts from those irqdomain.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device tree entries to declare gpio range. It will allow to use
no contiguous gpio bank and holes inside a bank.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO management is pretty simple and is part of the same IP than the pin
controller for the Armada 37xx SoCs. This patch adds the GPIO support to
the pinctrl-armada-37xx.c file, it also allows sharing common functions
between the gpiolib and the pinctrl drivers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We now trap accesses to CNTVCT_EL0 when the counter is broken
enough to require the kernel to mediate the access. But it
turns out that some existing userspace (such as OpenMPI) do
probe for the counter frequency, leading to an UNDEF exception
as CNTVCT_EL0 and CNTFRQ_EL0 share the same control bit.
The fix is to handle the exception the same way we do for CNTVCT_EL0.
Fixes: a86bd139f2 ("arm64: arch_timer: Enable CNTVCT_EL0 trap if workaround is enabled")
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a tab before it to follow standard practices. Also add the missing
full stop '.'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In function amd_iommu_bind_pasid(), the control flow jumps
to label out_free when pasid_state->mm and mm is NULL. And
mmput(mm) is called. In function mmput(mm), mm is
referenced without validation. This will result in a NULL
dereference bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: f0aac63b87 ('iommu/amd: Don't hold a reference to mm_struct')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some cipher implementations will crash if you try to use them
without calling setkey first. This patch adds a check so that
the accept(2) call will fail with -ENOKEY if setkey hasn't been
done on the socket yet.
Fixes: 400c40cf78 ("crypto: algif - add AEAD support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add scomp backend for zlib-deflate compression algorithm.
This backend outputs data using the format defined in rfc1950
(raw deflate surrounded by zlib header and footer).
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add crypto_register_scomps and crypto_unregister_scomps to allow
the registration of multiple implementations with one call.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Cc: <stable@vger.kernel.org> # 4.9.x+
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Cc: <stable@vger.kernel.org> # 4.9.x+
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
trivial spelling mistake, missing r, rename to ce_ring_control
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The cipher_null is not a real cipher, FIPS mode should not restrict its use.
It is used for several tests (for example in cryptsetup testsuite) and also
temporarily for reencryption of not yet encrypted device in cryptsetup-reencrypt tool.
Problem is easily reproducible with
cryptsetup benchmark -c null
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Acked-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a core_id file in the driver's sysfs directory,
exposing the hardware CORE ID. This is useful to allow
userspace to discover the hardware version used.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
All DPs have a COLORADJ matrix which is applied prior to output gamma.
Attach that to the CTM property. Also, ensure the input CTM's coefficients
can fit in the DP registers' Q3.12 format.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
