Memory bandwidth allocation requires different information than cache
allocation.
To avoid a lump of data in struct rdt_resource, move all cache related
information into a seperate structure and add that to struct rdt_resource.
Sanitize the data types while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: ravi.v.shankar@intel.com
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
Cc: vikas.shivappa@intel.com
This fixes the coding style issue of using (S_IWUSR | S_IRUGO) in place of
4-digit octal numbers.
Signed-off-by: Chen Guanqiao <chen.chenchacha@foxmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device operates in DIRECT_MODE and BUFFER_HARDWARE mode.
Replace usages of iio_dev->mlock with iio_device_{claim|release}_direct_mode()
helper functions to guarantee DIRECT mode and consequently protect
BUFFER mode too.
Add and use a device private lock to protect against conflicting access of the
state data.
This helps with IIO subsystem redefining iio_dev->mlock to be used by
the IIO core only for protecting device operating mode changes.
ie. Changes between INDIO_DIRECT_MODE, INDIO_BUFFER_* modes.
Protect changing of attributes inside ad5933_store(). Attributes
can no longer be changed while in buffered mode.
Remove lock from ad5933_work() because buffer mode should be enabled
when we reach this, and claiming DIRECT mode in all the other places
should protect it.
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Removing use of deprecated macros(S_IRUGO, S_IWUSR, S_IXUGO), and replace
with 4 digit octal.
Signed-off-by: Chen Guanqiao <chen.chenchacha@foxmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device counting could be controlled by the level or the edges of
a trigger.
in_count0_enable_mode attibute allow to set the control mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
One of the features of STM32 trigger hardware block is a quadrature
encoder that can counts up/down depending of the levels and edges
of the selected external pins.
This patch allow to read/write the counter, get it direction,
set/get quadrature modes and get scale factor.
When counting up preset value is the limit of the counter.
When counting down the counter start from preset value down to 0.
This preset value could be set/get by using
/sys/bus/iio/devices/iio:deviceX/in_count0_preset attribute.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
AS3935_WRITE_DATA macro bit is incorrect and the actual write
sequence is two leading zeros.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
realbits, storagebits and shift should be numbers, not ASCII characters.
Signed-off-by: Pavel Roskin <plroskin@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ALSA driver for TASCAM FireWire series transfers MIDI messages in system
workqueue. In current design of the driver, applications should wait for
sequence of transmission when they close ALSA rawmidi character devices.
However, when considering design of rawmidi interface, it's preferable
to wait in drain ioctl.
This commit adds support for the drain ioctl to wait for the end of
the transmission.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series handle MIDI messages with support for
running status. Drivers for the series should remember current running
status and transfer valid MIDI messages. For this purpose, current
ALSA driver for the series has some members in its top-level structure.
This is due to better abstraction of async midi port. Nowadays, the
abstraction was localized just for the driver.
This commit moves the members to structure for async midi port.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current design of ALSA driver for TASCAM FireWire series, initialization
of members in asymc midi port structure is done at device probing. Some of
the members should be initialized every time to use rawmidi devices because
they're changed in sequence of transmission for MIDI messages.
This commit adds a new function to initialize them. Invariant parameters
during object lifetime are kept as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series internally allocates 4 byte buffer
for asynchronous transaction to transfer MIDI messages. However, the buffer
can be allocated with memory object of parent structure.
This commit adds 4 byte array as a member of the structure and obsoletes
the redundant allocation. This is deallocated with memory object of parent
structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series receive MIDI messages by asynchronous
transactions on IEEE 1394 bus. Although the transaction is sent to a
certain register, current ALSA driver for this series has a redundant design.
This commit use the same address for the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses asynchronous transactions with fixed length
payload for MIDI messaging. On the other hand, ALSA driver for the series
has a redundant design to handle different length of payload.
This commit removes the redundant abstraction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of localization of async midi port, ALSA driver for TASCAM
FireWire series can call helper function directly instead of callback
registration.
This commit removes the redundant design.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Linux kernel 4.4, firewire-lib got a feature called as 'async midi port'
for transmission of MIDI message via IEEE 1394 asynchronous communication,
however actual consumer of this feature is ALSA driver for TASCAM FireWire
series only. When adding this feature, I assumed that ALSA driver for
Digi00x might also be a consumer, actually it's not.
This commit moves the feature from firewire-lib to firewire-tascam module.
Two minor kernel APIs are removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 561eb9d09a ("fbdev: omap/lcd: Make callbacks optional") made
panel callbacks optional but forgot to update check_required_callbacks().
As a result many (all?) OMAP systems using omapfb will crash at boot.
Fix by deleting the whole function.
Fixes: 561eb9d09a ("fbdev: omap/lcd: Make callbacks optional")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
* acpi-scan-fixes:
ACPI / scan: Set the visited flag for all enumerated devices
* acpica-fixes:
Revert "ACPICA: Resources: Not a valid resource if buffer length too long"
* pm-cpufreq-fixes:
cpufreq: Bring CPUs up even if cpufreq_online() failed
* pm-tools-fixes:
cpupower: Fix turbo frequency reporting for pre-Sandy Bridge cores
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
The m41t0 variant is very similar to the already supported m41t00
variant, with the notable exception of the oscillator fail bit.
The data sheet notes:
If the oscillator fail (OF) bit is internally set to a '1,' this
indicates that the oscillator has either stopped, or was stopped
for some period of time and can be used to judge the validity of
the clock and date data.
The bit will get cleared with a regular write of the system time,
so no changes are needed to clear it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There's a funny typo where IRQ_NONE is used instead of IRQF_TRIGGER_NONE
for request_threaded_irq(). Let's fix it before it gets copied elsewhere.
Fixes: dd3bf50b35 ("rtc: cpcap: new rtc driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some systems (e.g. Intel Bay Trail systems) the legacy PIC is not
used, in this case virq 8 will be a random irq, rather then hw_irq 8
from the PIC.
Requesting virq 8 in this case will not help us to get alarm irqs and
may cause problems for other drivers which actually do need virq 8,
for example on an Asus Transformer T100TA this leads to:
[ 28.745155] genirq: Flags mismatch irq 8. 00000088 (mmc0) vs. 00000080 (rtc0)
<snip oops>
[ 28.753700] mmc0: Failed to request IRQ 8: -16
[ 28.975934] sdhci-acpi: probe of 80860F14:01 failed with error -16
This commit fixes this by making the rtc-cmos driver continue
without using an irq rather then claiming irq 8 when no irq is
specified in the pnp-info and there are no legacy-irqs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The classic PC rtc-coms driver has a workaround for broken ACPI device
nodes for it which lack an irq resource. This workaround used to
unconditionally hardcode the irq to 8 in these cases.
This was causing irq conflict problems on systems without a legacy-pic
so a recent patch added an if (nr_legacy_irqs()) guard to the
workaround to avoid this irq conflict.
nr_legacy_irqs() uses the legacy_pic symbol under the hood causing
an undefined symbol error if the rtc-cmos code is build as a module.
This commit exports the legacy_pic symbol to fix this.
Cc: rtc-linux@googlegroups.com
Cc: alexandre.belloni@free-electrons.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function
graph tracing and then suspend to RAM, it will triple fault and reboot when
it resumes.
The first fault happens when booting a secondary CPU:
startup_32_smp()
load_ucode_ap()
prepare_ftrace_return()
ftrace_graph_is_dead()
(accesses 'kill_ftrace_graph')
The early head_32.S code calls into load_ucode_ap(), which has an an
ftrace hook, so it calls prepare_ftrace_return(), which calls
ftrace_graph_is_dead(), which tries to access the global
'kill_ftrace_graph' variable with a virtual address, causing a fault
because the CPU is still in real mode.
The fix is to add a check in prepare_ftrace_return() to make sure it's
running in protected mode before continuing. The check makes sure the
stack pointer is a virtual kernel address. It's a bit of a hack, but
it's not very intrusive and it works well enough.
For reference, here are a few other (more difficult) ways this could
have potentially been fixed:
- Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging
is enabled. (No idea what that would break.)
- Track down load_ucode_ap()'s entire callee tree and mark all the
functions 'notrace'. (Probably not realistic.)
- Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu()
or __cpu_up(), and ensure that the pause facility can be queried from
real mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net>
Cc: linux-acpi@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@kernel.org
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove a redundant self assignment of table->nr_entries, it does
nothing and is an artifact of code simplification re-work.
Detected by CoverityScan, CID#1428450 ("Self assignment")
Fixes: 441ac2f33d ("x86/boot/e820: Simplify e820__update_table()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Link: http://lkml.kernel.org/r/20170413155912.12078-1-colin.king@canonical.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Spurious NMIs will be observed with the following command:
while :; do
perf record -bae "cpu/umask=0x01,event=0xcd,ldlat=0x80/pp"
-e "cpu/umask=0x03,event=0x0/"
-e "cpu/umask=0x02,event=0x0/"
-e cycles,branches,cache-misses
-e cache-references -- sleep 10
done
The bug was introduced by commit:
8077eca079 ("perf/x86/pebs: Add workaround for broken OVFL status on HSW+")
That commit clears the status bits for the counters used for PEBS
events, by masking the whole 64 bits pebs_enabled. However, only the
low 32 bits of both status and pebs_enabled are reserved for PEBS-able
counters.
For status bits 32-34 are fixed counter overflow bits. For
pebs_enabled bits 32-34 are for PEBS Load Latency.
In the test case, the PEBS Load Latency event and fixed counter event
could overflow at the same time. The fixed counter overflow bit will
be cleared by mistake. Once it is cleared, the fixed counter overflow
never be processed, which finally trigger spurious NMI.
Correct the PEBS enabled mask by ignoring the non-PEBS bits.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 8077eca079 ("perf/x86/pebs: Add workaround for broken OVFL status on HSW+")
Link: http://lkml.kernel.org/r/1491333246-3965-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
During (post-commit) review Darren spotted a few minor things. One
(harmless AFAICT) type inconsistency and a comment that wasn't as
clear as hoped.
Reported-by: Darren Hart (VMWare) <dvhart@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexander reported a hrtimer debug_object splat:
ODEBUG: free active (active state 0) object type: hrtimer hint: hrtimer_wakeup (kernel/time/hrtimer.c:1423)
debug_object_free (lib/debugobjects.c:603)
destroy_hrtimer_on_stack (kernel/time/hrtimer.c:427)
futex_lock_pi (kernel/futex.c:2740)
do_futex (kernel/futex.c:3399)
SyS_futex (kernel/futex.c:3447 kernel/futex.c:3415)
do_syscall_64 (arch/x86/entry/common.c:284)
entry_SYSCALL64_slow_path (arch/x86/entry/entry_64.S:249)
Which was caused by commit:
cfafcd117d ("futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()")
... losing the hrtimer_cancel() in the shuffle. Where previously the
hrtimer_cancel() was done by rt_mutex_slowlock() we now need to do it
manually.
Reported-by: Alexander Levin <alexander.levin@verizon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: cfafcd117d ("futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1704101802370.2906@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have a tool to generate the PELT constants in C form,
use its output as a separate header.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We truncate (and loose) the lower 10 bits of runtime in
___update_load_avg(), this means there's a consistent bias to
under-account tasks. This is esp. significant for small tasks.
Cure this by only forwarding last_update_time to the point we've
actually accounted for, leaving the remainder for the next time.
Reported-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Historically our periods (or p) argument in PELT denoted the number of
full periods (what is now d2). However recent patches have changed
this to the total decay (previously p+1), leading to a confusing
discrepancy between comments and code.
Try and clarify things by making periods (in code) and p (in comments)
be the same thing (again).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paul noticed that in the (periods >= LOAD_AVG_MAX_N) case in
__accumulate_sum(), the returned contribution value (LOAD_AVG_MAX) is
incorrect.
This is because at this point, the decay_load() on the old state --
the first step in accumulate_sum() -- will not have resulted in 0, and
will therefore result in a sum larger than the maximum value of our
series. Obviously broken.
Note that:
decay_load(LOAD_AVG_MAX, LOAD_AVG_MAX_N) =
1 (345 / 32)
47742 * - ^ = ~27
2
Not to mention that any further contribution from the d3 segment (our
new period) would also push it over the maximum.
Solve this by noting that we can write our c2 term:
p
c2 = 1024 \Sum y^n
n=1
In terms of our maximum value:
inf inf p
max = 1024 \Sum y^n = 1024 ( \Sum y^n + \Sum y^n + y^0 )
n=0 n=p+1 n=1
Further note that:
inf inf inf
( \Sum y^n ) y^p = \Sum y^(n+p) = \Sum y^n
n=0 n=0 n=p
Combined that gives us:
p
c2 = 1024 \Sum y^n
n=1
inf inf
= 1024 ( \Sum y^n - \Sum y^n - y^0 )
n=0 n=p+1
= max - (max y^(p+1)) - 1024
Further simplify things by dealing with p=0 early on.
Reported-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: linux-kernel@vger.kernel.org
Fixes: a481db34b9 ("sched/fair: Optimize ___update_sched_avg()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Driver SDIO private data structure description includes a spin_lock
that is never used. This data structure only contains a pointer to the
sdio_func and a pointer to the main device private data. A spin_lock
is not required here.
Remove unused spin_lock.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver SDIO header describes a structure that is never used. It can be
safely removed.
Remove unused structure description.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
