Separating discards and zeroout operations allows us to remove the LBPRZ
block zeroing constraints from discards and honor the device preferences
for UNMAP commands.
If supported by the device, we'll also choose UNMAP over one of the
WRITE SAME variants for discards.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that zeroout and discards are distinct operations we need to
separate the policy of choosing the appropriate command. Create a
zeroing_mode which can be one of:
write: Zeroout assist not present, use regular WRITE
writesame: Allow WRITE SAME(10/16) with a zeroed payload
writesame_16_unmap: Allow WRITE SAME(16) with UNMAP
writesame_10_unmap: Allow WRITE SAME(10) with UNMAP
The last two are conditional on the device being thin provisioned with
LBPRZ=1 and LBPWS=1 or LBPWS10=1 respectively.
Whether to set the UNMAP bit or not depends on the REQ_NOUNMAP flag. And
if none of the _unmap variants are supported, regular WRITE SAME will be
used if the device supports it.
The zeroout_mode is exported in sysfs and the detected mode for a given
device can be overridden using the string constants above.
With this change in place we can now issue WRITE SAME(16) with UNMAP set
for block zeroing applications that require hard guarantees and
logical_block_size granularity. And at the same time use the UNMAP
command with the device's preferred granulary and alignment for discard
operations.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like DRBD assumes its on the wire TRIM request always zeroes data.
Use that fact to implement REQ_OP_WRITE_ZEROES.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
drbd always wants its discard wire operations to zero the blocks, so
use blkdev_issue_zeroout with the BLKDEV_ZERO_UNMAP flag instead of
reinventing it poorly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we have REQ_OP_WRITE_ZEROES implemented for all devices that
support efficient zeroing, we can remove the call to blkdev_issue_discard.
This means we only have two ways of zeroing left and can simplify the
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
mmc only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rsxx only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rbd only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's just a in-driver reimplementation of writing zeroes to the pages,
which fails if the discards aren't page aligned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's identical to discard as hole punches will always leave us with
zeroes on reads.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just the same as discard if the block size equals the system page size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
But now for the real NVMe Write Zeroes yet, just to get rid of the
discard abuse for zeroing. Also rename the quirk flag to be a bit
more self-explanatory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Try to use a write same with unmap bit variant if the device supports it
and the caller allows for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This gets us support for non-discard efficient write of zeroes (e.g. NVMe)
and prepares for removing the discard_zeroes_data flag.
Also remove a pointless discard support check, which is done in
blkdev_issue_discard already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This avoids fallbacks to explicit zeroing in (__)blkdev_issue_zeroout if
the caller doesn't want them.
Also clean up the convoluted check for the return condition that this
new flag is added to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If this flag is set logical provisioning capable device should
release space for the zeroed blocks if possible, if it is not set
devices should keep the blocks anchored.
Also remove an out of sync kerneldoc comment for a static function
that would have become even more out of data with this change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the existing discard flag into a new BLKDEV_ZERO_UNMAP flag with
similar semantics, but without referring to diѕcard.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We'll always use the WRITE ZEROES code for zeroing now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like the code currently passes whatever it was using for writes
to WRITE SAME. Just switch it to WRITE ZEROES, although that doesn't
need any payload.
Untested, and confused by the code, maybe someone who understands it
better than me can help..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix up do_region to not allocate a bio_vec for discards. We've
got rid of the discard payload allocated by the caller years ago.
Obviously this wasn't actually harmful given how long it's been
there, but it's still good to avoid the pointless allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy and past the REQ_OP_WRITE_SAME code to prepare to implementations
that limit the write zeroes size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make life easy for implementations that needs to send a data buffer
to the device (e.g. SCSI) by numbering it as a data out command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split sd_setup_discard_cmnd into one function per provisioning type. While
this creates some very slight duplication of boilerplate code it keeps the
code modular for additions of new provisioning types, and for reusing the
write same functions for the upcoming scsi implementation of the Write Zeroes
operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A patch documenting how to specify which kernels a particular fix should
be backported to (seemingly) inadvertently added a minus sign after the
kernel version. This particular stable-tag format had never been used
prior to this patch, and was neither present when the patch in question
was first submitted (it was added in v2 without any comment).
Drop the minus sign to avoid any confusion.
Fixes: fdc81b7910 ("stable_kernel_rules: Add clause about specification of kernel versions to patch.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit adds Japanese translation of HOWTO document into rst based
documentation build system with updates.
Signed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Use the correct chip name (e.g. lsm6dsm) as suffix for iio_dev name
instead of a generic one (lsm6dsx)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spinlock taken only for dma_map_single() for TX buffer is completely
useless and doesn't protect anything, so remove it to simplify the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds missing checks for dma_map_single() failure and proper error
reporting. Although this issue was harmless on ARM architecture, it is always
good to use the DMA mapping API in a proper way. This patch fixes the following
DMA API debug warning:
WARNING: CPU: 1 PID: 3785 at lib/dma-debug.c:1171 check_unmap+0x8a0/0xf28
dma-pl330 121a0000.pdma: DMA-API: device driver failed to check map error[device address=0x000000006e0f9000] [size=4096 bytes] [mapped as single]
Modules linked in:
CPU: 1 PID: 3785 Comm: (agetty) Tainted: G W 4.11.0-rc1-00137-g07ca963-dirty #59
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c072a114>] (check_unmap+0x8a0/0xf28)
[<c072a114>] (check_unmap) from [<c072a834>] (debug_dma_unmap_page+0x98/0xc8)
[<c072a834>] (debug_dma_unmap_page) from [<c0803874>] (s3c24xx_serial_shutdown+0x314/0x52c)
[<c0803874>] (s3c24xx_serial_shutdown) from [<c07f5124>] (uart_port_shutdown+0x54/0x88)
[<c07f5124>] (uart_port_shutdown) from [<c07f522c>] (uart_shutdown+0xd4/0x110)
[<c07f522c>] (uart_shutdown) from [<c07f6a8c>] (uart_hangup+0x9c/0x208)
[<c07f6a8c>] (uart_hangup) from [<c07c426c>] (__tty_hangup+0x49c/0x634)
[<c07c426c>] (__tty_hangup) from [<c07c78ac>] (tty_ioctl+0xc88/0x16e4)
[<c07c78ac>] (tty_ioctl) from [<c03b5f2c>] (do_vfs_ioctl+0xc4/0xd10)
[<c03b5f2c>] (do_vfs_ioctl) from [<c03b6bf4>] (SyS_ioctl+0x7c/0x8c)
[<c03b6bf4>] (SyS_ioctl) from [<c010b4a0>] (ret_fast_syscall+0x0/0x3c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.0+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.
These irqs were already disabled in .startup but this might be too late.
Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.
So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.
The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:
-- CPU a -- -- CPU b --
(take port lock)
pl011_start_tx
pl011_start_tx_pio
enable TXIM in REG_IMSC -> causes uart tx intr (pl011_int)
pl011_tx_chars pl011_int
...tx chars, all done... (wait for port lock)
pl011_stop_tx .
disable TXIM .
(release port lock) -> (take port lock)
check for TXIM, not enabled
(release port lock)
return IRQ_NONE
Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.
Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <Vijaya.Kumar@cavium.com>
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Power management is disabled then the clocks are not getting
enabled. This patch enables it for the !PM case also.
While at it also pm_runtime_set_active is called before
calling pm_runtime_enable.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk(KERN_INFO ) by pr_info(). It seems last printk()
call in serial_core.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow modifications of port name. It's serial core's business only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serdev_device_write() a blocking call allowing to transfer
arbitraty amount of data (potentially exceeding amount that
serdev_device_write_buf can process in a single call)
To support that, also add serdev_device_write_wakeup().
Drivers wanting to use full extent of serdev_device_write
functionality are expected to provide serdev_device_write_wakeup() as
a sole handler of .write_wakeup event or call it as a part of driver's
custom .write_wakeup code.
Because serdev_device_write() subroutine is a superset of
serdev_device_write_buf() the patch re-impelements latter is terms of
the former. For drivers wanting to just use serdev_device_write_buf()
.write_wakeup handler is optional.
Cc: cphealy@gmail.com
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SC9860 use the same serial device which SC9836 uses, so added a new
compatible string to support SC9860 as well, also added an example
of how to describe this serial device in DT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added bindings for Spreadtrum SP9860G board and SC9860 SoC.
This patch also revised bindings of SC9836 to make the format
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.
As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to accommodate in a logical manner for the premuxed channels
in PM8921 and the similarly addressed channels in later PMICs, we
need a twocell arrangement with premux and analog mux setting as
a tuple to uniquely identify a hardware channel.
These bindings are not yet in use, so it should be fine to augment
them before we actually start using it in drivers and device trees.
This scheme came out of lengthy discussions and reverse-engineering
and reading of the few information sources we have.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh+dt@kernel.org>
Suggested-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>