Allow writing to 'consistency_policy' attribute when the array is
active. Add a new function 'change_consistency_policy' to the
md_personality operations structure to handle the change in the
personality code. Values "ppl" and "resync" are accepted and
turn PPL on and off respectively.
When enabling PPL its location and size should first be set using
'ppl_sector' and 'ppl_size' attributes and a valid PPL header should be
written at this location on each member device.
Enabling or disabling PPL is performed under a suspended array. The
raid5_reset_stripe_cache function frees the stripe cache and allocates
it again in order to allocate or free the ppl_pages for the stripes in
the stripe cache.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Add a function to modify the log by removing an rdev when a drive fails
or adding when a spare/replacement is activated as a raid member.
Removing a disk just clears the child log rdev pointer. No new stripes
will be accepted for this child log in ppl_write_stripe() and running io
units will be processed without writing PPL to the device.
Adding a disk sets the child log rdev pointer and writes an empty PPL
header.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Load the log from each disk when starting the array and recover if the
array is dirty.
The initial empty PPL is written by mdadm. When loading the log we
verify the header checksum and signature. For external metadata arrays
the signature is verified in userspace, so here we read it from the
header, verifying only if it matches on all disks, and use it later when
writing PPL.
In addition to the header checksum, each header entry also contains a
checksum of its partial parity data. If the header is valid, recovery is
performed for each entry until an invalid entry is found. If the array
is not degraded and recovery using PPL fully succeeds, there is no need
to resync the array because data and parity will be consistent, so in
this case resync will be disabled.
Due to compatibility with IMSM implementations on other systems, we
can't assume that the recovery data block size is always 4K. Writes
generated by MD raid5 don't have this issue, but when recovering PPL
written in other environments it is possible to have entries with
512-byte sector granularity. The recovery code takes this into account
and also the logical sector size of the underlying drives.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Add 'consistency_policy' attribute for array. It indicates how the array
maintains consistency in case of unexpected shutdown.
Add 'ppl_sector' and 'ppl_size' for rdev, which describe the location
and size of the PPL space on the device. They can't be changed for
active members if the array is started and PPL is enabled, so in the
setter functions only basic checks are performed. More checks are done
in ppl_validate_rdev() when starting the log.
These attributes are writable to allow enabling PPL for external
metadata arrays and (later) to enable/disable PPL for a running array.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Implement the calculation of partial parity for a stripe and PPL write
logging functionality. The description of PPL is added to the
documentation. More details can be found in the comments in raid5-ppl.c.
Attach a page for holding the partial parity data to stripe_head.
Allocate it only if mddev has the MD_HAS_PPL flag set.
Partial parity is the xor of not modified data chunks of a stripe and is
calculated as follows:
- reconstruct-write case:
xor data from all not updated disks in a stripe
- read-modify-write case:
xor old data and parity from all updated disks in a stripe
Implement it using the async_tx API and integrate into raid_run_ops().
It must be called when we still have access to old data, so do it when
STRIPE_OP_BIODRAIN is set, but before ops_run_prexor5(). The result is
stored into sh->ppl_page.
Partial parity is not meaningful for full stripe write and is not stored
in the log or used for recovery, so don't attempt to calculate it when
stripe has STRIPE_FULL_WRITE.
Put the PPL metadata structures to md_p.h because userspace tools
(mdadm) will also need to read/write PPL.
Warn about using PPL with enabled disk volatile write-back cache for
now. It can be removed once disk cache flushing before writing PPL is
implemented.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Move raid5-cache declarations from raid5.h to raid5-log.h, add inline
wrappers for functions which will be shared with ppl and use them in
raid5 core instead of direct calls to raid5-cache.
Remove unused parameter from r5c_cache_data(), move two duplicated
pr_debug() calls to r5l_init_log().
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Include information about PPL location and size into mdp_superblock_1
and copy it to/from rdev. Because PPL is mutually exclusive with bitmap,
put it in place of 'bitmap_offset'. Add a new flag MD_FEATURE_PPL for
'feature_map', analogically to MD_FEATURE_BITMAP_OFFSET. Add MD_HAS_PPL
to mddev->flags to indicate that PPL is enabled on an array.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In r5cache recovery, the journal device is scanned page by page.
Currently, we use sync_page_io() to read journal device. This is
not efficient when we have to recovery many stripes from the journal.
To improve the speed of recovery, this patch introduces a read ahead
page pool (ra_pool) to recovery_ctx. With ra_pool, multiple consecutive
pages are read in one IO. Then the recovery code read the journal from
ra_pool.
With ra_pool, r5l_recovery_ctx has become much bigger. Therefore,
r5l_recovery_log() is refactored so r5l_recovery_ctx is not using
stack space.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Previous patch (raid5: only dispatch IO from raid5d for harddisk raid)
defers IO dispatching. The goal is to create better IO pattern. At that
time, we don't sort the deffered IO and hope the block layer can do IO
merge and sort. Now the raid5-cache writeback could create large amount
of bios. And if we enable muti-thread for stripe handling, we can't
control when to dispatch IO to raid disks. In a lot of time, we are
dispatching IO which block layer can't do merge effectively.
This patch moves further for the IO dispatching defer. We accumulate
bios, but we don't dispatch all the bios after a threshold is met. This
'dispatch partial portion of bios' stragety allows bios coming in a
large time window are sent to disks together. At the dispatching time,
there is large chance the block layer can merge the bios. To make this
more effective, we dispatch IO in ascending order. This increases
request merge chance and reduces disk seek.
Signed-off-by: Shaohua Li <shli@fb.com>
Bump the flush stripe batch size to 2048. For my 12 disks raid
array, the stripes takes:
12 * 4k * 2048 = 96MB
This is still quite small. A hardware raid card generally has 1GB size,
which we suggest the raid5-cache has similar cache size.
The advantage of a big batch size is we can dispatch a lot of IO in the
same time, then we can do some scheduling to make better IO pattern.
Last patch prioritizes stripes, so we don't worry about a big flush
stripe batch will starve normal stripes.
Signed-off-by: Shaohua Li <shli@fb.com>
In raid5-cache writeback mode, we have two types of stripes to handle.
- stripes which aren't cached yet
- stripes which are cached and flushing out to raid disks
Upperlayer is more sensistive to latency of the first type of stripes
generally. But we only one handle list for all these stripes, where the
two types of stripes are mixed together. When reclaim flushes a lot of
stripes, the first type of stripes could be noticeably delayed. On the
other hand, if the log space is tight, we'd like to handle the second
type of stripes faster and free log space.
This patch destinguishes the two types stripes. They are added into
different handle list. When we try to get a stripe to handl, we prefer
the first type of stripes unless log space is tight.
This should have no impact for !writeback case.
Signed-off-by: Shaohua Li <shli@fb.com>
To update size for cluster raid, we need to make
sure all nodes can perform the change successfully.
However, it is possible that some of them can't do
it due to failure (bitmap_resize could fail). So
we need to consider the issue before we set the
capacity unconditionally, and we use below steps
to perform sanity check.
1. A change the size, then broadcast METADATA_UPDATED
msg.
2. B and C receive METADATA_UPDATED change the size
excepts call set_capacity, sync_size is not update
if the change failed. Also call bitmap_update_sb
to sync sb to disk.
3. A checks other node's sync_size, if sync_size has
been updated in all nodes, then send CHANGE_CAPACITY
msg otherwise send msg to revert previous change.
4. B and C call set_capacity if receive CHANGE_CAPACITY
msg, otherwise pers->resize will be called to restore
the old value.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Support resize is a little complex for clustered
raid, since we need to ensure all the nodes share
the same knowledge about the size of raid.
We achieve the goal by check the sync_size which
is in each node's bitmap, we can only change the
capacity after cluster_check_sync_size returns 0.
Also, get_bitmap_from_slot is added to get a slot's
bitmap. And we exported some funcs since they are
used in cluster_check_sync_size().
We can also reuse get_bitmap_from_slot to remove
redundant code existed in bitmap_copy_from_slot.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The msg type CHANGE_CAPACITY is introduced to support
resize clustered raid in later patch, and it is sent
after all the nodes have the same sync_size, receiver
node just need to set new capacity once received this
msg.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Previously, when node received METADATA_UPDATED msg, it just
need to wakeup mddev->thread, then md_reload_sb will be called
eventually.
We taken the asynchronous way to avoid a deadlock issue, the
deadlock issue could happen when one node is receiving the
METADATA_UPDATED msg (wants reconfig_mutex) and trying to run
the path:
md_check_recovery -> mddev_trylock(hold reconfig_mutex)
-> md_update_sb-metadata_update_start
(want EX on token however token is
got by the sending node)
Since we will support resizing for clustered raid, and we
need the metadata update handling to be synchronous so that
the initiating node can detect failure, so we need to change
the way for handling METADATA_UPDATED msg.
But, we obviously need to avoid above deadlock with the
sync way. To make this happen, we considered to not hold
reconfig_mutex to call md_reload_sb, if some other thread
has already taken reconfig_mutex and waiting for the 'token',
then process_recvd_msg() can safely call md_reload_sb()
without taking the mutex. This is because we can be certain
that no other thread will take the mutex, and we also certain
that the actions performed by md_reload_sb() won't interfere
with anything that the other thread is in the middle of.
To make this more concrete, we added a new cinfo->state bit
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD
Which is set in lock_token() just before dlm_lock_sync() is
called, and cleared just after. As lock_token() is always
called with reconfig_mutex() held (the specific case is the
resync_info_update which is distinguished well in previous
patch), if process_recvd_msg() finds that the new bit is set,
then the mutex must be held by some other thread, and it will
keep waiting.
So process_metadata_update() can call md_reload_sb() if either
mddev_trylock() succeeds, or if MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD
is set. The tricky bit is what to do if neither of these apply.
We need to wait. Fortunately mddev_unlock() always calls wake_up()
on mddev->thread->wqueue. So we can get lock_token() to call
wake_up() on that when it sets the bit.
There are also some related changes inside this commit:
1. remove RELOAD_SB related codes since there are not valid anymore.
2. mddev is added into md_cluster_info then we can get mddev inside
lock_token.
3. add new parameter for lock_token to distinguish reconfig_mutex
is held or not.
And, we need to set MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD in below:
1. set it before unregister thread, otherwise a deadlock could
appear if stop a resyncing array.
This is because md_unregister_thread(&cinfo->recv_thread) is
blocked by recv_daemon -> process_recvd_msg
-> process_metadata_update.
To resolve the issue, MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD is
also need to be set before unregister thread.
2. set it in metadata_update_start to fix another deadlock.
a. Node A sends METADATA_UPDATED msg (held Token lock).
b. Node B wants to do resync, and is blocked since it can't
get Token lock, but MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD is
not set since the callchain
(md_do_sync -> sync_request
-> resync_info_update
-> sendmsg
-> lock_comm -> lock_token)
doesn't hold reconfig_mutex.
c. Node B trys to update sb (held reconfig_mutex), but stopped
at wait_event() in metadata_update_start since we have set
MD_CLUSTER_SEND_LOCK flag in lock_comm (step 2).
d. Then Node B receives METADATA_UPDATED msg from A, of course
recv_daemon is blocked forever.
Since metadata_update_start always calls lock_token with reconfig_mutex,
we need to set MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD here as well, and
lock_token don't need to set it twice unless lock_token is invoked from
lock_comm.
Finally, thanks to Neil for his great idea and help!
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Buffer is a pointer to the static char array event_buffer and therefore
can never be null, so the check is redundant. Remove it.
Detected by CoverityScan, CID#1077556 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chang <dpf@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We shouldn't kfree(rtc) because is devm_ managed memory. It leads to a
double free.
Fixes: dd3bf50b35 ("rtc: cpcap: new rtc driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The to_wm8350_from_rtc_dev macro is not used by anything in the
rtc-wm8350 driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver is orphan since commit b2026f708e ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it probably means it's no longer used and is
thus a good candidate for removal.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 3.13
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: bba5394ad3 ("Input: add support for Hanwang tablets")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.37
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: aca951a22a ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.14
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.
Fixes: 628329d524 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.28
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A modern compiler should know better when to inline, so drop the inline
keywords.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use unsigned int instead of plain unsigned as reported by checkpatch.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While this isn't an issue according to checkpatch two styles are used.
Add a blank line to the block comments missing a blank line at the start
so multiline block comments look the same across the file.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When acpi_dev_gpio_irq_get gets called with an index of say 2, it should
not care if acpi_get_gpiod for index 0 or 1 returns -EPROBE_DEFER.
This allows drivers which request a gpioint with index > 0 to function
if there is no gpiochip driver (loaded) for gpioints with a lower index.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpiod_count() does not return 0 anymore, we don't need to shadow
its error code and would safely propagate to the user.
While here, replace second parameter by NULL in order to prevent side
effects on _DSD enabled firmware.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpiod_count() does not return 0 anymore, we don't need to shadow
its error code and would safely propagate to the user.
While here, replace second parameter by NULL in order to prevent side
effects on _DSD enabled firmware.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of this platform.
Update compile dependencies and ACPI ID to reflect this change.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
[Drop depreciation of ARCH_VULCAN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zx gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ws16c48 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pl061 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The etraxfs gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ath79 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm-kona gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 104-dio-48e gpio driver currently implements an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The altera gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a real-time
kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT
kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This should be impossible, but let's assert that we do not pin a context
4 billion times before retiring!
v2: Fix the assertion -- the patch had just one job to do!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171628.3228-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
2+ PCI devices fail to be discovered due to each bus having the same PCI
domain. This is because the domain defined in the device tree file is not
being added due to PCI_DOMAIN not being enabled. So, every PCI bus has a
domain of zero. When PCI_DOMAIN is selected by the Kconfig, it picks up
the domain defined in the device tree file and everything works as
expected.
Since both PCIE_IPROC_PLATFORM and PCIE_IPROC_BCMA need PCI_DOMAIN, move
it to PCIE_IPROC so it will be automatically selected for both.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>