It seems the code had been changed, but description left untouched.
Update description of the struct acpi_gpio_info and relative comments
accordingly.
Fixes: commit 52044723cd ("ACPI / gpio: Add irq_type when a GPIO is used as an interrupt")
Cc: Christophe RICARD <christophe.ricard@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.
Check for short transfers, and make sure to log any transfer errors.
Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).
Fixes: 6ce7610478 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The macro for_each_set_bit() effectively looks up to the next
set bit in array of bits.
Instead of open coding that switch to for_each_set_bit() in
gpio_chip_set_multiple().
While here, make gpio_chip_set_multiple() non-destructive
against its parameters. We are safe since all callers, i.e.
gpiod_set_array_value_complex(), handle that already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
davinci_gpio_controller struct has set_data, in_data, clr_data
members that are assigned and never used.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In current code, the @changed always returns the last one's status for
the huge page with the contiguous bit set. This is really not what we
want. Even one of the PTEs is changed, we should tell it to the caller.
This patch fixes this issue.
Fixes: 66b3923a1a ("arm64: hugetlb: add support for PTE contiguous bit")
Cc: <stable@vger.kernel.org> # 4.5.x-
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In ca91cx42_slave_get function, the value pointed by vme_base pointer is
set through:
*vme_base = ioread32(bridge->base + CA91CX42_VSI_BS[i]);
So it must be dereferenced to be used in calculation of pci_base:
*pci_base = (dma_addr_t)*vme_base + pci_offset;
This bug was caught thanks to the following gcc warning:
drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’:
drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
*pci_base = (dma_addr_t)vme_base + pci_offset;
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-By: Martyn Welch <martyn@welchs.me.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tick is stopped and an interrupt occurs afterward, we check on
that interrupt exit if the next tick needs to be rescheduled. If it
doesn't need any update, we don't want to do anything.
In order to check if the tick needs an update, we compare it against the
clockevent device deadline. Now that's a problem because the clockevent
device is at a lower level than the tick itself if it is implemented
on top of hrtimer.
Every hrtimer share this clockevent device. So comparing the next tick
deadline against the clockevent device deadline is wrong because the
device may be programmed for another hrtimer whose deadline collides
with the tick. As a result we may end up not reprogramming the tick
accidentally.
In a worst case scenario under full dynticks mode, the tick stops firing
as it is supposed to every 1hz, leaving /proc/stat stalled:
Task in a full dynticks CPU
----------------------------
* hrtimer A is queued 2 seconds ahead
* the tick is stopped, scheduled 1 second ahead
* tick fires 1 second later
* on tick exit, nohz schedules the tick 1 second ahead but sees
the clockevent device is already programmed to that deadline,
fooled by hrtimer A, the tick isn't rescheduled.
* hrtimer A is cancelled before its deadline
* tick never fires again until an interrupt happens...
In order to fix this, store the next tick deadline to the tick_sched
local structure and reuse that value later to check whether we need to
reprogram the clock after an interrupt.
On the other hand, ts->sleep_length still wants to know about the next
clock event and not just the tick, so we want to improve the related
comment to avoid confusion.
Reported-by: James Hartsock <hartsjc@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Link: http://lkml.kernel.org/r/1483539124-5693-1-git-send-email-fweisbec@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After rollover of the IOVA space, we want to get a low IOVA address,
otherwise the the games we play by remembering the last IOVA are
pointless. When we search for a free hole with DRM_MM_SEARCH_DEFAULT,
drm_mm will pop the next entry from the free holes stack, which will
likely be a high IOVA. By using DRM_MM_SEARCH_BELOW we can trick
drm_mm into reversing the search and provide us with a low IOVA.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Wladimir van der Laan <laanwj@gmail.com>
Understanding this code is getting out of control without any
notes. Give the firmware_class driver a much needed documentation love,
and while at it convert it to the new sphinx documentation format.
v2: typos and small fixes
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error that we expect should not be spilled to stdout.
Without this we get:
./fw_filesystem.sh: line 58: printf: write error: Invalid argument
./fw_filesystem.sh: line 63: printf: write error: No such device
./fw_filesystem.sh: line 69: echo: write error: No such file or directory
./fw_filesystem.sh: filesystem loading works
./fw_filesystem.sh: async filesystem loading works
With it:
./fw_filesystem.sh: filesystem loading works
./fw_filesystem.sh: async filesystem loading works
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to load test_firmware if its already there.
Also use a more generic form to recommend what is required
to be built.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes we have the following error message:
platform MSFT0101:00: failed to claim resource 1
acpi MSFT0101:00: platform device creation failed: -16
But there is not enough information to figure out which resource range
failed to claim.
Thus print the resource range at first-place thus /proc/iomem or
ioports should tell us who already claimed this resource, then
the driver bug or incorrect resource assignment which is running
into this conflict can be diagnosed:
platform MSFT0101:00: failed to claim resource 1: [mem 0xfed40000-0xfed40fff]
acpi MSFT0101:00: platform device creation failed: -16
Suggested-by: Len Brown <lenb@kernel.org>
Reported-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On most platforms, there exists this ifdef:
#define atomic_inc_not_zero(v) atomic_add_unless((v), 1, 0)
This makes this patch functionally useless. However, on PPC, there is
actually an explicit definition of atomic_inc_not_zero with its own
assembly that is slightly more optimized than atomic_add_unless. So,
this patch changes kref to use atomic_inc_not_zero instead, for PPC and
any future platforms that might provide an explicit implementation.
This also puts this usage of kref more in line with a verbatim reading
of the examples in Paul McKenney's paper [1] in the section titled "2.4
Atomic Counting With Check and Release Memory Barrier", which uses
atomic_inc_not_zero.
[1] http://open-std.org/jtc1/sc22/wg21/docs/papers/2007/n2167.pdf
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Type of debugfs_real_fops() is longer than parameters and
the name, so there is no way to break the declaration nicely.
We have to go over 80 characters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vme_driver structure currently has a "node" entry. This entry is
never used and it's intended purpose has been lost to the mists of time.
Remove the entry from vme_driver to avoid confusion.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AER recovery, pci_error_handlers.link_reset() is never called,
drop it now.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the power domain driver of zx296718
which belongs to zte's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ARMv8 zx2967 family (296718, 296716 etc) uses different value
for controlling the power domain on/off registers, Choose the
value depending on the compatible.
Multiple domains are prepared for the family, this patch prepares
the common functions.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds header with values used for ZTE 2967
SoC's power domain driver.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the ZTE SoC drivers as maintained by ARM ZTE
architecture maintainers, as they're parts of the core IP.
By the way, this patch adds the maintainer for ARM
ZTE architecture to Baoyou Xie.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds device tree bindings document for ZTE zx2967
family power domain controller.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous fix of a memory leak now prints the string 'name'
that was previously free'd. Fix this by free'ing the string
at the end of the function and adding an error exit path for
the error conditions.
CoverityScan CID#1384523 ("Use after free")
Fixes: 2bd362d5f4 ("ppdev: fix memory leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function get_zeroed_page() returns a NULL pointer if there is no enough
memory. In function extcon_sync(), it returns 0 if the call to
get_zeroed_page() fails. The return value 0 indicates success in the
context, which is incosistent with the execution status. This patch
fixes the bug by returning -ENOMEM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188611
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: a580982f08
Cc: stable <stable@vger.kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/gpu/drm/selftests/test-drm_mm.c:1277 evict_everything()
warn: calling list_del() inside list_for_each
The list_del() inside the error handling in the eviction loop is
overkill. We have to undo the eviction scan to return the drm_mm back to
a recoverable state, so have to iterate over the full list, but we only
want to report the error once and once we have an error we can return
early.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 560b328429 ("drm: kselftest for drm_mm and eviction")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110144031.7609-1-chris@chris-wilson.co.uk
This commit needs to be reverted because it prevents people from
using the serial console as a secondary console with input being
directed to tty0.
IOW, if you boot with console=ttyS0 console=tty0 then all kernels
prior to this commit will produce output on both ttyS0 and tty0
but input will only be taken from tty0. With this patch the serial
console will always be the primary console instead of tty0,
potentially preventing people from getting into their machines in
emergency situations.
Fixes: d03516df83 ("tty: serial: 8250: add CON_CONSDEV to flags")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in RS485 emulation mode, __do_stop_tx_rs485() calls
serial8250_clear_fifos(). This not only clears the FIFOs, but also sets
all bits in their control register (UART_FCR) to 0.
One of the effects of this is the disabling of the FIFOs, which turns
them into single-byte holding registers. The rest of the driver doesn't
know this, which results in the lions share of characters passed into a
write call to be dropped.
(I can supply logic analyzer screenshots if necessary)
This fix replaces the serial8250_clear_fifos() call to
serial8250_clear_and_reinit_fifos() - this prevents the "dropped
characters" issue from manifesting again while retaining the requirement
of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX
flag is disabled.
Signed-off-by: Daniel Jedrychowski <avistel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without a bool string present, using "# CONFIG_DEVPORT is not set" in
defconfig files would not actually unset devport. This esnured that
/dev/port was always on, but there are reasons a user may wish to
disable it (smaller kernel, attack surface reduction) if it's not being
used. Adding a message here in order to make this user visible.
Signed-off-by: Max Bires <jbires@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Cc: stable@vger.kernel.org
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Cc: <stable@vger.kernel.org> (beware, this won't apply before 4.3)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When borrowing the pfn_valid() check from mmap_kmem(), somebody managed
to get physical and virtual addresses spectacularly muddled up, such
that we've ended up with checks for one being the other. Whilst this
does indeed prevent out-of-bounds accesses crashing, on most systems
it also prevents the more desirable use-case of working at all ever.
Check the *virtual* offset correctly for what it is. Furthermore, do
so in the right place - a read or write may span multiple pages, so a
single up-front check is insufficient. High memory accesses already
have a similar validity check just before the copy_to_user() call, so
just make the low memory path fully consistent with that.
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
CC: stable@vger.kernel.org
Fixes: 148a1bc843 ("drivers: char: mem: Check {read,write}_kmem() addresses")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sending OS version for support of TPM2_ChangeEPS() is required only
for SPT FW (HMB version 2.0) and newer.
On older platforms the command should be just ignored by the firmware
but some older platforms misbehave so it's safer to send the command
only if required.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192051
Fixes: 7279b238ba (mei: send OS type to the FW)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update Linux driver to use new pdTargetId field for JBOD target ID
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ldio outstanding variable needs to be decremented in io completion path for
iMR dual queue depth
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large SEQ IO workload should sent as non fast path commands
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Megaraid driver has to support the SAS3.5 Generic Megaraid Controllers Firmware functionality.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid Controllers FW will support new dynamic RaidMap to have different
sizes for different number of supported VDs.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from SCSI layer to RAID volume through the Firmware.
Based on PCI bandwidth and write payload, every second this feature is
enabled/disabled.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An UNMAP command on a PI formatted device will leave the Logical Block Application
Tag and Logical Block Reference Tag as all F's (for those LBAs that are unmapped).
To avoid IO errors if those LBAs are subsequently read before they are written with
valid tag fields, the MPI SCSI IO requests need to set the EEDPFlags element EEDP
Escape Mode field, Bits [7:6] appropriately. A value of 2 should be set to disable
all PI checks if the Logical Block Application Tag is 0xFFFF for PI types 1 and 2.
A value of 3 should be set to disable all PI checks if the Logical Block Application
Tag is 0xFFFF and the Logical Block Reference Tag is 0xFFFFFFFF for PI type 3.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS3.5 Generic Megaraid based Controllers will have the support for 128 MSI-X vectors,
resulting in the need to support 128 reply queues
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch contains new pci device ids for SAS3.5 Generic Megaraid Controllers
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit f1bc1e4c44 ("ata: acpi: rework the ata acpi bind support")
removed scsi_register_acpi_bus_type() and
scsi_unregister_acpi_bus_type(), but forgot to remove them in the header
file, do it now.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.
Revamp the fixup setup:
1. Rename ufs_device_info to ufs_dev_desc as very similar name
ufs_dev_info is already in use.
2. Make the handlers static as they are not used out of the ufshdc.c
file.
[mkp: applied by hand]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reading big endian value from a buffer requires explicit cast.
Fix sparse warning:
drivers/scsi/ufs/ufshcd.c:4825:24: warning: cast to restricted __be16
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unexport ufshcd_read_device_desc and ufshcd_read_string_desc there is no
really possibility to calling them directly outside of UFS context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following compilation warning:
drivers/scsi/ufs/ufshcd.c:2076:5: warning: no previous prototype for
ufshcd_query_descriptor_retry [-Wmissing-prototypes]
Also do not export the function, it should not be used out of ufs
context.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>