Commit graph

693,635 commits

Author SHA1 Message Date
Ian Abbott
1c5a6eab8b staging: comedi: daqboard2000: remove unused 'card' member
The `card` member of `struct daqboard2000_private` and the enumerated
constant `card_daqboard_2000` are not used.  Remove them.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
fba4e898b9 staging: comedi: daqboard2000: check CPLD status before writing firmware data
According to an old GPL'ed driver at
<ftp://ftp.mccdaq.com/downloads/iotech_software/DaqBoard_1000_2000_Series/Linux_driver_kernelv2.4.x/>,
The CPLD status register can be checked to make sure that it is ready to
accept the next 16-bit word of FPGA firmware data, but that doesn't work
on older versions of the CPLD, where a simple delay should be used
between successive writes.  The current version of the Comedi driver
just uses a delay between successive writes.  Change it to check for the
newer CPLD in the `daqboard2000_load_firmware()`, and change the
firmware word writing function `daqboard2000_write_cpld()` to wait for
the status bit (`DB2K_CPLD_STATUS_TXREADY`, previously called
`DB2K_CPLD_TXDONE`) to be set for newer CPLD, or just delay for older CPLD.
Return an error if it times out waiting for the status bit.

The wait for the `DB2K_CPLD_STATUS_TXREADY` status bit to be set is
performed by new function `daqboard2000_wait_cpld_txready()`, which
returns 0 if the status bit is set within 100 microseconds, or
`-ETIMEDOUT` if not.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
f8d7b3b2f9 staging: comedi: daqboard2000: check result of FPGA programming
According to an old, GPL'ed Linux driver at
<ftp://ftp.mccdaq.com/downloads/iotech_software/DaqBoard_1000_2000_Series/Linux_driver_kernelv2.4.x/>,
after programming the FPGA, the General Purpose Input (USERI) of the PLX
PCI-9080 should go high shortly after a valid FPGA bitstream has been
loaded.  Add a new function `daqboard2000_wait_fpga_programmed()` to
wait for that, performing up to 200 checks over a 20 ms period (this is
loosely based on `pollFPGADone()` in the above-mentioned old driver).
Return 0 if the FPGA appears to have loaded successfully, or
`-ETIMEDOUT` if it runs out of checks.  Call it from the firmware
loading callback `daqboard2000_load_firmware()` after writing the
firmware to the FPGA to check it is programmed successfully.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
7680a22729 staging: comedi: daqboard2000: change daqboard2000_write_cpld() return value
`daqboard2000_write_cpld()` currently returns 1 on success, or 0 on
failure.  Change it to return 0 on success, or `-EIO` on failure.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
90bc9cb34b staging: comedi: daqboard2000: replace daqboard2000_poll_cpld()
`daqboard2000_poll_cpld()` waits for a specified status bit in the CPLD
status register to be set, giving up after 50 tries over a period of
about 5 milliseconds.  It returns 1 if the status bit is set, otherwise
0.  It is only ever called to check the "INIT" status bit.  Replace it
with new function `daqboard2000_wait_cpld_init()`, which returns 0 if
the "INIT" status bit becomes set within 50 tries, or `-ETIMEDOUT` if
not set within 50 tries.  The firmware loading callback
`daqboard2000_load_firmware()` may return the error result from
`daqboard2000_wait_cpld_init()` if it has used up all its firmware
loading attempts and that was the last error.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
7cff0b776a staging: comedi: daqboard2000: check firmware length
Firmware files for DAQBoard/2000 have a header, which is skipped,
followed by a sequence of FPGA configuration bytes to be programmed in
pairs.  The FPGA configuration bytes start with the sequence 0xff, 0x20.

Make the firmware loading callback function
`daqboard2000_load_firmware()` return an error `-EINVAL` if the FPGA
start sequence is not found, or the remaining length is not a multiple
of 2.

The firmware loading callback tries to program the FPGA up to 3 times
until it succeeds or it has tried too many times.  Currently, it
searches for the FPGA start sequence in the firmware data each time
through the retry loop.  Change it to adjust the start position and
length before entering the loop.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
3bc3a82390 staging: comedi: daqboard2000: use type 'u16' for CPLD data and status
The CPLD status and data registers used to load firmware are 16 bits
wide.  Use the type `u16` to represent data and status values instead of
`int`.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
1736bcf3c5 staging: comedi: daqboard2000: define macros for CPLD registers
The Daqboard/2000 uses a write-only data register and a read-only status
register in a pre-programmed CPLD device to program the main firmware on
the board.  Both registers are at offset 0x1000 from PCI BAR 2.  Define
macros for the register offsets.  Rename the existing macros for the
status register values for consistency.  (Two status bits are defined,
but the driver code only seems to use one of them.)

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Ian Abbott
1d7f14dd92 staging: comedi: daqboard2000: use macros from "plx9080.h"
The Daqboard/2000 uses a PLX PCI-9080 chip to interface with the PCI
bus.  The "daqboard2000" driver uses the PCI-9080 "CNTRL" register to
perform various tasks, but defines its own macros for the register
values.  Use the macros from "plx9080.h" instead.  The various functions
that change the CNTRL register just wiggle individual bits up and down,
but they ignore the current register value - the old macros defined the
full value to be written to the register.  Change them to read and
modify the register value.

Also remove a read of the CNTRL register in `daqboard2000_auto_attach()`
where the value is just thrown away, as it seems to serve no purpose
there (such as flushing PCI writes).

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:38:32 +01:00
Markus Buettner
168400d0e9 staging: wlan-ng: remove unnecessary blank lines
checkpatch.pl complained about two unnecessary blank lines after an
opening '{' in prism2mib.c. Those were removed in order to get rid
of those warnings.

There are more issues pointed out by checkpatch.pl. Those require
additional work to be done.

Signed-off-by: Markus Buettner <markus.buettner@fau.de>
Signed-off-by: Artur Wasinger <artur.wasinger@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:37:25 +01:00
Derek Robson
f4535f4eae Staging: speakup: style fix, octal file permissions
Changed file permission to octal style,
Can't use __ATTR_RW() as the handler is in standard format.
Found using checkpatch

Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:37:25 +01:00
Aditya Shankar
05a157403c staging: wilc1000: Connect to highest RSSI value for required SSID
Connect to the highest rssi with the required SSID in the shadow
table if the connection criteria is based only on the SSID.
For the first matching SSID, an index to the table is saved.
Later the index is updated if matching SSID has a higher
RSSI value than the last saved index.

However if decision is made based on BSSID, there is only one match
in the table and corresponding index is used.

changes in v2:
initialize sel_bssi_idx to UINT_MAX.
Combine two checks for identifying
sel_bssi_idx value for a SSID.

Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:37:25 +01:00
Tomeu Vizoso
246ee524a2 drm/i915: Put "cooked" vlank counters in frame CRC lines
Use drm_accurate_vblank_count so we have the full 32 bit to represent
the frame counter and userspace has a simpler way of knowing when the
counter wraps around.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-3-tomeu.vizoso@collabora.com
2017-01-10 17:30:56 +01:00
Tomeu Vizoso
8c6b709d96 drm/i915: Use new CRC debugfs API
The core provides now an ABI to userspace for generation of frame CRCs,
so implement the ->set_crc_source() callback and reuse as much code as
possible with the previous ABI implementation.

When handling the pageflip interrupt, we skip 1 or 2 frames depending on
the HW because they contain wrong values. For the legacy ABI for
generating frame CRCs, this was done in userspace but now that we have a
generic ABI it's better if it's not exposed by the kernel.

v2:
    - Leave the legacy implementation in place as the ABI implementation
      in the core is incompatible with it.
v3:
    - Use the "cooked" vblank counter so we have a whole 32 bits.
    - Make sure we don't mess with the state of the legacy CRC capture
      ABI implementation.
v4:
    - Keep use of get_vblank_counter as in the legacy code, will be
      changed in a followup commit.

v5:
    - Skip first frame or two as it's known that they contain wrong
      data.
    - A few fixes suggested by Emil Velikov.

v6:
    - Rework programming of the HW registers to preserve previous
      behavior.

v7:
    - Address whitespace issue.
    - Added a comment on why in the implementation of the new ABI we
      skip the 1st or 2nd frames.

v9:
    - Add stub for intel_crtc_set_crc_source.

v12:
    - Rebased.
    - Remove stub for intel_crtc_set_crc_source and instead set the
      callback to NULL (Jani Nikula).

v15:
    - Rebased.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>

irq
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-2-tomeu.vizoso@collabora.com
2017-01-10 17:30:50 +01:00
Tobias Klauser
dc647ec88e net: socket: Make unnecessarily global sockfs_setattr() static
Make sockfs_setattr() static as it is not used outside of net/socket.c

This fixes the following GCC warning:
net/socket.c:534:5: warning: no previous prototype for ‘sockfs_setattr’ [-Wmissing-prototypes]

Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-10 11:29:50 -05:00
Abdul Rauf
f631a97048 staging: unisys: fix checkpatch block comments warning
Fix the following warnings:
Block comments should align the * on each line

Signed-off-by: Abdul Rauf <abdulraufmujahid@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:47 +01:00
Derek Robson
dca71b0fba Staging: unisys: visorbus: visorchipset.c: style fix
Changed file permissions to octal sytle.
Found using checkpatch.

Acked-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
Derek Robson
b3d76e80c7 Staging: unisys: visorbus: visorbus_main.c: fixed style
Changed file permissions to octal sytle.
Found using checkpatch.

Acked-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
Tim Sell
9eedb509af staging: unisys: remove redundant unlocks of visornic_devdata.priv_lock
These redundant unlocks of visornic_devdata.priv_lock would result in
the RHEL 7.2 guests hanging during service partition recovery testing.

__Testing__

* An scp of a large file was started from a remote host TO the RHEL 7.2
  Linux guest.

* During the scp transfer, s-Par service partition recovery was forced
  twice. After each occasion, I verified that the guest recovered
  completely (all s-Par guest devices), and that the file transfer
  resumed.

* Within the RHEL 7.2 guest environment, copied the large file to
  another location in the local filesystem.

* During the copy, s-Par service partition recovery was again forced
  twice. After each occasion, I verified that the guest recovered
  completely (all s-Par guest devices), and that the copy resumed.

* An scp of the new copy of the large file was started FROM the RHEL 7.2
  guest to a remote host.

* During the scp transfer, s-Par service partition recovery was forced
  twice. After each occasion, I verified that the guest recovered
  completely (all s-Par guest devices), and that the file transfer
  resumed.

* Used cmp to verify that the large file had successfully survived the
  round-trip without becoming corrupted.

Signed-off-by: Tim Sell <Timothy.Sell@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David Binder
ef44146cb7 staging: unisys: visornic: Remove errant -EIO returns
Remove errant -EIOs that prevent us from calling either
netif_start_queue() or napi_disable().

Signed-off-by: David Binder <david.binder@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David Binder
6219e49333 staging: unisys: visornic: Reorder logic in visornic_enable_with_timeout()
Moves the call to napi_enable() before the call to init_rcv_bufs(),
ensuring that messages are not put into the receive queue until the guest
is ready to receive interrupts.

Signed-off-by: David Binder <david.binder@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David Binder
4b3d7b6d84 staging: unisys: visorbus: Remove duplicate invocation of init_rcv_bufs()
Removes the invocation to init_rcv_bufs() in visornic_resume() because that
function is already called in visornic_enable_with_timeout().

Signed-off-by: David Binder <david.binder@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David Kershner
046f93dc72 staging: unisys: visorbus: Replace parser_param_start with parser_name_get
Replace the general CONTROLVM string parser setup which only handled the
name string with a specific name string retrieval function.

Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
Tim Sell
396e36c9ac staging: unisys: visorbus: relocate error-check from isr to registration
It just makes more sense to do the NULL-pointer check when the function is
called to enable interrupts, rather than on *every* interrupt.

Signed-off-by: Tim Sell <Timothy.Sell@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David Kershner
db2003f524 staging: unisys: visorbus: Remove unused enum members
Visorchipset used to parse CONTROLVM messages with a variety of string
information. All but the name string have been removed, but the code
to handle this information remained. This patch removes the other values
and handlers.

Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:29:46 +01:00
David S. Miller
2bc979f273 wireless-drivers fixes for 4.10
Only two fixes at this time. The rtlwifi fix is an important one as it
 fixes a reported oops and Linus was already asking about it. The
 orinoco fix is not tested on a real device, because it's old legacy
 hardware and hardly no-one use it, but it should fix a (theoretical)
 issue with VMAP_STACK.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJYdG+sAAoJEG4XJFUm622bGo0IAJCx6Ibu+EjbfL1KDDiR4TSS
 ZuWHkjVHtbSE0itUCws9RXWCBStUsDV/eFlVax7zBk4XiLtmDKHG0Kvb6K+Bm1qy
 rOEgmj8Y0mYzuAHR5efgC5LyyxRqKxGeff20TUZYHQ2KcWmfe5hZi0FJpo0gFjp0
 1CUZiSAFuiQmaM6mGleSRZndN65m+bSRjM8yfxTC24XqjdfTVzSXo68Cp4gYk/XE
 M62gAg0fyk7UPBwBDztmCtARNW2Zr/OGolQp9ohyOxj3iAuazvTpohywA7Fa0vZu
 piBwZJGMAy1ZXHgK58qvoq1ej51RNq+ttjQKiXt9YinL/YBIcs+AkvvVzDFjzZk=
 =5g7Z
 -----END PGP SIGNATURE-----

Merge tag 'wireless-drivers-for-davem-2017-01-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.10

Only two fixes at this time. The rtlwifi fix is an important one as it
fixes a reported oops and Linus was already asking about it. The
orinoco fix is not tested on a real device, because it's old legacy
hardware and hardly no-one use it, but it should fix a (theoretical)
issue with VMAP_STACK.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-10 11:27:46 -05:00
Parav Pandit
9c1e67f941 rdmacg: Added documentation for rdmacg
Added documentation for v1 and v2 version describing high
level design and usage examples on using rdma controller.

Signed-off-by: Parav Pandit <pandit.parav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:14:27 -05:00
Parav Pandit
43579b5f2c IB/core: added support to use rdma cgroup controller
Added support APIs for IB core to register/unregister every IB/RDMA
device with rdma cgroup for tracking rdma resources.
IB core registers with rdma cgroup controller.
Added support APIs for uverbs layer to make use of rdma controller.
Added uverbs layer to perform resource charge/uncharge functionality.
Added support during query_device uverb operation to ensure it
returns resource limits by honoring rdma cgroup configured limits.

Signed-off-by: Parav Pandit <pandit.parav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:14:27 -05:00
Parav Pandit
39d3e7584a rdmacg: Added rdma cgroup controller
Added rdma cgroup controller that does accounting, limit enforcement
on rdma/IB resources.

Added rdma cgroup header file which defines its APIs to perform
charging/uncharging functionality. It also defined APIs for RDMA/IB
stack for device registration. Devices which are registered will
participate in controller functions of accounting and limit
enforcements. It define rdmacg_device structure to bind IB stack
and RDMA cgroup controller.

RDMA resources are tracked using resource pool. Resource pool is per
device, per cgroup entity which allows setting up accounting limits
on per device basis.

Currently resources are defined by the RDMA cgroup.

Resource pool is created/destroyed dynamically whenever
charging/uncharging occurs respectively and whenever user
configuration is done. Its a tradeoff of memory vs little more code
space that creates resource pool object whenever necessary, instead of
creating them during cgroup creation and device registration time.

Signed-off-by: Parav Pandit <pandit.parav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:14:27 -05:00
Bartlomiej Zolnierkiewicz
7e11aabd48 ata: add Atari Falcon PATA controller driver
Add Atari Falcon PATA controller driver.  The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.

Tested under ARAnyM emulator.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:11:18 -05:00
Bartlomiej Zolnierkiewicz
989e0aac1a ata: pass queued command to ->sff_data_xfer method
For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method.  Update core code and all users
accordingly.

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:11:17 -05:00
Bartlomiej Zolnierkiewicz
7563f62546 ata: allow subsystem to be used on m68k arch
When libata was merged m68k lacked IOMAP support.  This has not been
true for a long time now so allow subsystem to be used on m68k.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:11:17 -05:00
Christoph Hellwig
a234f7395c libata: switch to dynamic allocation instead of ata_scsi_rbuf
Note of the emulated commands in the pageout/pagein path, so just do
a GFP_NOIO dynamic allocation.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 11:05:21 -05:00
Daniel Vetter
05adb1850a Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next-queued
Pull in latest drm-next from Dave Airlie to get at all the drm-misc
goodies, specifically:
- dma_fence error state handling rework (Chris needs that for error
  recovery)
- crc support locking changes (Tomeu's i915 crc patches need that).

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2017-01-10 17:03:46 +01:00
Andy Lutomirski
620f1a632e wusbcore: Fix one more crypto-on-the-stack bug
The driver put a constant buffer of all zeros on the stack and
pointed a scatterlist entry at it.  This doesn't work with virtual
stacks.  Use ZERO_PAGE instead.

Cc: stable@vger.kernel.org # 4.9 only
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:03:42 +01:00
Mateusz Berezecki
1129d270cb USB: Increase usbfs transfer limit
Promote a variable keeping track of USB transfer memory usage to a
wider data type and allow for higher bandwidth transfers from a large
number of USB devices connected to a single host.

Signed-off-by: Mateusz Berezecki <mateuszb@fastmail.fm>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:42 +01:00
Krzysztof Opasiak
444d930998 tools: usb: usbip: Update README
Update README file:
- remove outdated parts
- clarify terminology and general structure
- add some description of vUDC

Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:42 +01:00
Krzysztof Kozlowski
68bd6fc3cf usb: host: ohci-exynos: Decrese node refcount on exynos_ehci_get_phy() error paths
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount.  Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.

Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:42 +01:00
Krzysztof Kozlowski
3f6026b1dc usb: host: ehci-exynos: Decrese node refcount on exynos_ehci_get_phy() error paths
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount.  Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.

Fixes: 6d40500ac9 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:42 +01:00
John Crispin
808cf33d48 usb: make the MTK XHCI driver compile for older MIPS SoCs
The MIPS based MT7621 shares the same XHCI core as the newer generation of
ARM based SoCs. The driver works out of the box and we only need to make it
buildable in Kconfig.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:41 +01:00
Colin Ian King
9038a03875 usb: renesas_usbhs: mod_host: fix typo: "connecte" -> "connected"
trivial fix to typo in dev_dbg message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:41 +01:00
Aaro Koskinen
bf2b419aa1 USB: ohci-omap: defer probe if PHY is missing
Defer probe if PHY is missing. E.g. on Nokia 770 several modules needs
to be loaded to get the PHY going and ohci-omap should wait for those.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:41 +01:00
Krzysztof Opasiak
a52d3ec54a tools: usb: usbip: Add simple script to show how to setup vUDC
Add some simple script which creates a USB gadget using ConfigFS
and then exports it using vUDC.

This may be useful for people who just started playing with
USB/IP and vUDC as it shows exact steps how to setup all stuff.

Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-10 17:00:41 +01:00
Christoph Hellwig
a0c0b0e945 libata: don't call ata_scsi_rbuf_fill for command without a response buffer
No need to copy a zeroed buffer to the caller if the command is defined
to not have a response in the SCSI spec.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 10:55:40 -05:00
Christoph Hellwig
8fc6c0657b libata: call ->scsi_done from ata_scsi_simulate
We always need to call ->scsi_done after we've finished emulating a
command, so do it in a single place at the end of ata_scsi_simulate.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 10:55:40 -05:00
Christoph Hellwig
506db3609c libata: remove the done callback from ata_scsi_args
It's always the scsi_done callback, and we can get at that easily
in the place where ->done is called.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 10:55:40 -05:00
Christoph Hellwig
f0a37d12f5 libata: move struct ata_scsi_args to libata-scsi.c
It's only used in libata-scsi.c, so move it closer to the users.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 10:55:39 -05:00
Christoph Hellwig
aa18da8b7e libata: avoid global response buffer in atapi_qc_complete
We only need to look at 4 bytes of the inquiry response for ATAPI
devices.  Instead of using the global ata_scsi_rbuf just use a
a stack buffer.  Also factor the fixup into it's own little helper
function to make it more readable.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
2017-01-10 10:55:38 -05:00
Johan Hovold
146cc8a17a USB: serial: kl5kusb105: fix line-state error handling
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.

Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2017-01-10 16:42:26 +01:00
Chris Wilson
957870f934 drm/i915: Split out i915_gem_object_set_tiling()
Expose an interface for changing the tiling and stride on an object,
that includes the complexity of checking for conflicting bindings and
fence registers.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110121045.27144-2-chris@chris-wilson.co.uk
2017-01-10 15:29:14 +00:00