It is necessary to use hwirq instead of virq when you communicate
with an interrupt controller since there is no guaranty that virq
numbers match hwirq numbers.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The I2C LCD display on the Cyclone5 and Arria5 devkits is only capable of
the standard 100 kHz clock. Set the "clock-frequency" of the I2C node
to be 100000.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the compatible string for supporting the generic device tree cpufreq-dt
driver on APM's X-Gene 2 SoC.
Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
1) stmmac_drv_probe() can race with stmmac_open() because we register
the netdevice too early. Fix from Florian Fainelli.
2) UFO handling in __ip6_append_data() and ip6_finish_output() use
different tests for deciding whether a frame will be fragmented or
not, put them in sync. Fix from Zheng Li.
3) The rtnetlink getstats handlers need to validate that the netlink
request is large enough, fix from Mathias Krause.
4) Use after free in mlx4 driver, from Jack Morgenstein.
5) Fix setting of garbage UID value in sockets during setattr() calls,
from Eric Biggers.
6) Packet drop_monitor doesn't format the netlink messages properly
such that nlmsg_next fails to work, fix from Reiter Wolfgang.
7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
Nault.
8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.
9) IGMP code doesn't reset group query timers properly, from Michal
Tesar.
10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
Alexander Duyck.
11) vxlan offload check needs to be more strict in be2net driver, from
Sabrina Dubroca.
12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
fix from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sh_eth: enable RX descriptor word 0 shift on SH7734
sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
dpaa_eth: Initialize CGR structure before init
dpaa_eth: cleanup after init_phy() failure
net: systemport: Pad packet before inserting TSB
net: systemport: Utilize skb_put_padto()
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
libcxgb: fix error check for ip6_route_output()
net: usb: asix_devices: add .reset_resume for USB PM
net: vrf: Add missing Rx counters
drop_monitor: consider inserted data in genlmsg_end
benet: stricter vxlan offloading check in be_features_check
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
net: macb: Updated resource allocation function calls to new version of API.
net: stmmac: dwmac-oxnas: use generic pm implementation
net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
net: stmmac: dwmac-oxnas: fix of-node leak
Documentation/networking: fix typo in mpls-sysctl
igmp: Make igmp group member RFC 3376 compliant
flow_dissector: Update pptp handling to avoid null pointer deref.
...
$type_struct_full and friends are only used by the restructuredText
backend, because it needs to separate enum/struct/typedef/union from
the name of the type. However, $type_struct is *also* used by the rST
backend. This is confusing.
This patch replaces $type_struct's use in the rST backend with a new
$type_fallback; it modifies $type_struct so that it can be used in the
rST backend; and creates regular expressions like $type_struct
for enum/typedef/union, for use in all backends.
Note that, compared to $type_*_full, in the new regexes $1 includes both
the "kind" and the name (before, $1 was pretty much a constant).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Note that, in order to produce the correct Docbook markup, the "." or "->"
must be separated from the member name in the regex's captured fields. For
consistency, this change is applied to $type_member and $type_member_func
too, not just to $type_member_xml.
List mode only prints the struct name, to avoid any undesired change in
the operation of docproc.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The restructuredText output includes both the parameter type and
the name for functions and function-typed members. Do the same
for docbook.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
An inline function can have an attribute, as in include/linux/log2.h,
and kernel-doc handles this already for simple cases. However,
some attributes have arguments (e.g. the "target" attribute).
Handle those too.
Furthermore, attributes could be at the beginning of a function
declaration, before the return type. To correctly handle this case,
you need to strip spaces after the attributes; otherwise, dump_function
is left confused.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A prototype like
/**
* foo - sample definition
* @bar: a parameter
*/
int foo(int (*bar)(int x,
int y));
is currently producing
.. c:function:: int foo (int (*bar) (int x, int y)
sample definition
**Parameters**
``int (*)(int x, int y) bar``
a parameter
Collapse the spaces so that the output is nicer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Even though the jitter due to USB1.1 may be 1ms,
NTP can reduce its effect significantly. And
USB2.0 reduces this anyway.
Signed-off-by: Sanjeev Gupta <ghane0@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
No semantic changes. The next patch in this series will
do the actual changes to sync with NTP current
best practices
Signed-off-by: Sanjeev Gupta <ghane0@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
timepps.h , as well as PPS sample test utilities, are
no longer in the kernel tree. Update documentation
to point to new locations.
Signed-off-by: Sanjeev Gupta <ghane0@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Lookup in the ATU can be performed starting from a given MAC
address. This is faster than starting with the first possible MAC
address and iterating all entries.
Entries are returned in numeric order. So if the MAC address returned
is bigger than what we are searching for, we know it is not in the
ATU.
Using the benchmark provided by Volodymyr Bendiuga
<volodymyr.bendiuga@gmail.com>,
https://www.spinics.net/lists/netdev/msg411550.html
on an Marvell Armada 370 RD, the test to add a number of static fdb
entries went from 1.616531 seconds to 0.312052 seconds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO charger is using a mix of the legacy GPIO interface
and <linux/of_gpio.h> which is not the modern way to use GPIOs.
Refactor like this:
- Use a GPIO descriptor for the GPIO line used to monitor the
charger.
- Fetch the descriptor with devm_gpiod_get() as the first
method.
- If this fails and we are *not* using device tree, then
start looking to see if we can use platform data instead.
- After looking up and requesting a GPIO number with the
legacy API, convert it to a descriptor.
This way we can later isolate and drop the legacy code as
more platforms move over to using descriptors.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
trivial fix to spelling mistake in comments in the headers
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
pdata is being null checked twice, the 2nd check is redundant code
and can be removed.
Fixes CoverityScan CID 1392340 "Logically dead code"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Setting the irq_enable bits is taken care of by the irq chip when we
request the irqs and the driver should not be meddling with the
irq?_en registers itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If there is no ti,ac-detect-gpios configured, it is normal to
have failed reads of the options register. So, hold back on the
log spamming.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
It is possible to verify AC adapter presence via a register read, without
any physical connection to the ACOK pin on the charger. Allow this.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Prior to this commit the code was using 1 notifier_block for all
types of charger cable, this is incorrect as the notifier_block
becomes part of a linked-list and now the same notifier_block
is part of 3 linked lists.
This commit fixes this by using a separate nb per extcon cable.
Note this happened to work fine sofar because axp288_charger was the only
listener, so when added to each of the 3 notifier chains, the next pointer
in the nb would be set to 0, so we've 3 heads pointing to the same nb,
with its next pointing to NULL. But as soon as we mix in a second extcon
consumer things will go boom.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a MODULE_DEVICE_TABLE to fix the module not auto-loading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Setting the irq_enable bits is taken care of by the irq chip when we
request the irqs and the driver should not be meddling with the
irq?_en registers itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
To set a bit to 1 one needs to pass the mask for the bit to set
as second argument into regmap_update_bits, not "1".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Do not wait for an extcon notification before processing the cable
states, instead queue the otg / cable work on probe to make sure we
immediately process the initial hardware state.
Note this also requiree moving the getting of the USB_HOST cable state
from the extcon notifier to the workqueue function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove info->health, info->present and info->online caching, as no code
is reading the cached values.
Remove if (changed) check before calling power_supply_changed(), we
return early from axp288_charger_extcon_evt_worker if nothing has
changed, so the check is not needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Deal with the charger type changing without a vbus-disconnect being
reported in between the 2 charger type states:
-Do not return from axp288_charger_extcon_evt_worker early in this case
(track old_chg_type)
-Make calling axp288_charger_enable_charger with the same value as before
a nop, to avoid the need for the caller to check this
-Do no do a dev_err when axp288_charger_enable_charger returns an error,
axp288_charger_enable_charger already returns an error itself
-Disable the charger before changing the charge-current setting (nop if
vbus was seen as disconnected before the change)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Nothing was setting info->otg.cable, so the extcon_get_cable_state_
calls on it would always return -EINVAL.
This commit fixes this by actually setting info->otg.cable using the new
extcon_get_extcon_dev_by_cable_id function.
This commit also makes failing to register the extcon notifier for the
USB_HOST cable an error rather then a warning, because we MUST have this
notfier to properly disable the VBUS path when in host mode so that we're
not drawing current from the 5V boost converter which is supplying power
to the otg port when in host mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Move the charger_init_hw_regs() above the power_supply_register call,
the axp288_charger_usb_set_property() uses axp288_chrg_info.max_cv and
.max_cc which get set by charger_init_hw_regs().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The extcon notifier work calls power_supply_changed on the power_supply
we register, so the extcon notifiers should be registered after we
register the power_supply.
While touching this code anyways, refactor the code for the 3 cable types
into a loop to avoid code repetition.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_power_supply_register instead of power_supply_register,
this avoids the need to do manual cleanup and results in quite
a nice code cleanup.
Note it may seem excessive to add a "struct device *dev" helper local
variable for the 1 time it is used in this patch, but future patches
in this series also use it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds support for sbs-charger compilant chips as defined here:
http://sbs-forum.org/specs/sbc110.pdf
This was tested on a arm board connected to an LTC4100 battery charger
chip.
Signed-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adds device tree documentation for SBS charger compilant devices as defined
here: http://sbs-forum.org/specs/sbc110.pdf
Signed-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
So what if there is a status_gpio specified? bq24735_charger_is_present()
do have a working fallback for the case of no status_gpio.
Simplify this by not special casing setups w/o status_gpio, folding
two consecutive if-blocks in the process.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
During probe, it makes no sense to take care to first not issue any
i2c commands to verify if the connected part really is a bq24735, to
later simply fail the probe in the next step when trying to configure
the charger. So, delay configuration of the charging parameters until
the charger is accessible (i.e. when the AC adapter is present) as
part of enabling the charging.
This also fixes the rather serious issue that the charging parameters
are lost when the AC adapter is disconnected.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
bq24735_enable_charging() needs to call bq24735_config_charging(),
which is something to change later, this is just a preparatory patch.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
"tps65217-charger" is more appropriate name because the driver supports
not only AC but also USB charger.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>