commit caca925fca upstream.
This prevents a malicious USB device from causing an oops.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 226ba70774 upstream.
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 12afb34400 upstream.
Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f49cf3b8b4 upstream.
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d1b12075ff upstream.
Calling pwm_config() with a period equal to zero always results in
error (-EINVAL) and pwm chip config method is never called.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1ff5fa3c67 upstream.
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit affa80bd97 upstream.
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit eda5ecc0a6 upstream.
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 162f98dea4 upstream.
The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.
Also let's fix a minor coding style issue.
The full correct report of this issue can be found in the public
Red Hat Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=1283385
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 82be788c96 upstream.
Looks like the fimware 8.2 still has the extra buttons spurious release
bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=114321
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a0ad220c96 upstream.
A malicious device missing interface can make the driver oops.
Add sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 950336ba3e upstream.
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9c6ba45671 upstream.
The powermate driver expects at least one valid USB endpoint in its
probe function. If given malicious descriptors that specify 0 for
the number of endpoints, it will crash. Validate the number of
endpoints on the interface before using them.
The full report for this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/85
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8e20cf2bce upstream.
The aiptek driver crashes in aiptek_probe() when a specially crafted USB
device without endpoints is detected. This fix adds a check that the device
has proper configuration expected by the driver. Also an error return value
is changed to more matching one in one of the error paths.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6544a1df11 upstream.
When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit dd0d0d4de5 upstream.
Without i8042.nomux=1 the Elantech touch pad is not working at all on
a Fujitsu Lifebook U745. This patch does not seem necessary for all
U745 (maybe because of different BIOS versions?). However, it was
verified that the patch does not break those (see opensuse bug 883192:
https://bugzilla.opensuse.org/show_bug.cgi?id=883192).
Signed-off-by: Aurélien Francillon <aurelien@francillon.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 60603950f8 upstream.
Another Lifebook machine that needs the same quirk as other similar
models to make the driver working.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=883192
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cee3d8ccbe upstream.
The legacy system PM support has long time ago been dropped from the
AMBA bus. Align to that by converting to the modern system PM
callbacks.
Fixes: 26825cfd90 (ARM: 7914/1: amba: Drop legacy PM support ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb38f3a4f6 upstream.
We've got bug reports showing the old systemd-logind (at least
system-210) aborting unexpectedly, and this turned out to be because
of an invalid error code from close() call to evdev devices. close()
is supposed to return only either EINTR or EBADFD, while the device
returned ENODEV. logind was overreacting to it and decided to kill
itself when an unexpected error code was received. What a tragedy.
The bad error code comes from flush fops, and actually evdev_flush()
returns ENODEV when device is disconnected or client's access to it is
revoked. But in these cases the fact that flush did not actually happen is
not an error, but rather normal behavior. For non-disconnected devices
result of flush is also not that interesting as there is no potential of
data loss and even if it fails application has no way of handling the
error. Because of that we are better off always returning success from
evdev_flush().
Also returning EINTR from flush()/close() is discouraged (as it is not
clear how application should handle this error), so let's stop taking
evdev->mutex interruptibly.
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=939834
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 968491709e upstream.
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 692dd19164 upstream.
This adds new icbody type to the list recognized by Elantech PS/2 driver.
Signed-off-by: Sam Hung <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5f0ee9d17a upstream.
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3c0213d17a upstream.
When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.
This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 47c1ffb2b6 upstream.
Add two more Fujitsu LIFEBOOK models that also ship with the Elantech
touchpad and don't work with crc_disabled to the quirk list.
Signed-off-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0dc1587905 upstream.
The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c42bfd7f6c upstream.
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bd884149ac upstream.
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b57a7128be upstream.
The board id capability has been added in firmware 7.5.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ebc80840b8 upstream.
The Fimware 8.1 has a bug in which the extra buttons are only sent when the
ExtBit is 1. This should be fixed in a future FW update which should have
a bump of the minor version.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit dc5465dc8a upstream.
On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle
button of the trackstick (attached to the touchpad serio device, of course)
seems to get lost.
Actually, the touchpads reports 3 extra buttons, which falls in the switch
below to the '2' case. Let's handle the case of odd numbers also, so that
the middle button finds its way back.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 02e07492cd upstream.
Post-2013 Lenovo laptops provide correct min/max dimensions, which are
different with the ones currently quirked. According to
https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids
are assigned in the post-2013 touchpads:
t440p/t440s: LEN0036 -> 2964/2962
t540p: LEN0034 -> 2964
Using 2961 as the common minimum makes these 3 laptops OK. We may need
to update those values later if other pnp_ids has a lower board_id.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5b3089ddb5 upstream.
Add a min/max range for board ids to the min/max coordinates quirk. This
makes it possible to restrict quirks to specific models based upon their
board id. The define ANY_BOARD_ID (0) serves as a wild card.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541
Signed-off-by: Daniel Martin <daniel.martin@secunet.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b05f4d1c33 upstream.
The firmware of the X240 (LEN0035, 2013/12) exposes the same values
x [1232..5710], y [1156..4696]
as the quirk applies.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ac097930f0 upstream.
Query the min dimensions even if the check
SYN_EXT_CAP_REQUESTS(priv->capabilities) >= 7 fails, but we know that the
firmware version 8.1 is safe.
With that we don't need quirks for post-2013 models anymore as they expose
correct min and max dimensions.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
re-order the tests to check SYN_CAP_MIN_DIMENSIONS even on FW 8.1
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9aff65982d upstream.
Logging the dimension values we queried and the values we use from a quirk
to overwrite can be helpful for debugging.
This partly relates to bug:
https://bugzilla.kernel.org/show_bug.cgi?id=91541
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8b04baba10 upstream.
Split the function synaptics_resolution() into synaptics_resolution() and
synaptics_quirks(). synaptics_resolution() will be called before
synaptics_quirks() to query dimensions and resolutions before overwriting
them with quirks.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2c75ada625 upstream.
The matches_pnp_id function from the synaptics driver is useful for other
drivers too. Make it a generic psmouse helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[ luis: 3.16-stable prereq for:
8b04baba10 "Input: synaptics - split synaptics_resolution(), query first" ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 33e5df0e0e upstream.
It appears that the Cintiq Companion Hybrid does not send an ABS_MISC event to
userspace when any of its ExpressKeys are pressed. This is not strictly
necessary now that the pad exists on its own device, but should be fixed for
consistency's sake.
Traditionally both the stylus and pad shared the same device node, and
xf86-input-wacom would use ABS_MISC for disambiguation. Not sending this causes
the Hybrid to behave incorrectly with xf86-input-wacom beginning with its
8f44f3 commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[killertofu@gmail.com: ported to drivers/input/tablet/wacom_wac.c]
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1d90d6d552 upstream.
Without this the aux port does not get detected, and consequently the touchpad
will not work.
With this patch the touchpad is detected:
$ dmesg | grep -E "(SYN|i8042|serio)"
pnp 00:03: Plug and Play ACPI device, IDs SYN1d22 PNP0f13 (active)
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126800, board id: 2863, fw id: 1473085
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
dmidecode excerpt for this laptop is:
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Medion
Product Name: Akoya E7225
Version: 1.0
Signed-off-by: Jochen Hein <jochen@jochen.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7c4f56070f upstream.
The 'max' size passed into the function is measured in number of bits
(KEY_MAX, LED_MAX, etc) so we need to convert it accordingly before trying
to copy the data out, otherwise we will try copying too much and end up
with up with a page fault.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9333caeaea upstream.
When KBC is in active multiplexing mode the touchpad on this laptop does
not work.
Reported-by: Bilal Koc <koc.bilo@googlemail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 810aa0918b upstream.
This change allows the driver to recognize newer Elantech touchpads.
Signed-off-by: Yi ju Hong <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 148e9a711e upstream.
On some laptops, keyboard needs to be reset in order to successfully detect
touchpad (e.g., some Gigabyte laptop models with Elantech touchpads).
Without resettin keyboard touchpad pretends to be completely dead.
Based on the original patch by Mateusz Jończyk this version has been
expanded to include DMI based detection & application of the fix
automatically on the affected models of laptops. This has been confirmed to
fix problem by three users already on three different models of laptops.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81331
Signed-off-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Tested by: Zakariya Dehlawi <zdehlawi@gmail.com>
Tested-by: Guillaum Bouchard <guillaum.bouchard@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 92788ac1eb upstream.
If kzalloc() failed and then evdev_open_device() fails, evdev_open()
will pass a vmalloc'ed pointer to kfree.
This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where
there was a crash in kfree().
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Belatedly-Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a1f9a40726 upstream.
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bce4f9e764 upstream.
The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.
touchpad-edge-detector output:
> Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
> Move one finger around the touchpad to detect the actual edges
> Kernel says: x [1472..5674], y [1408..4684]
> Touchpad sends: x [1264..5675], y [1171..4688]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0224ec9e9f upstream.
Fix the format string for serio device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4b54625822 upstream.
Add the USB ID for the Xbox 360 Thrustmaster Ferrari 458 Racing Wheel.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
