commit 071b6d4a5d upstream.
Currently, loading of a task's fpsimd state into the CPU registers
is skipped if that task's state is already present in the registers
of that CPU.
However, the code relies on the struct fpsimd_state * (and by
extension struct task_struct *) to unambiguously identify a task.
There is a particular case in which this doesn't work reliably:
when a task exits, its task_struct may be recycled to describe a
new task.
Consider the following scenario:
1) Task P loads its fpsimd state onto cpu C.
per_cpu(fpsimd_last_state, C) := P;
P->thread.fpsimd_state.cpu := C;
2) Task X is scheduled onto C and loads its fpsimd state on C.
per_cpu(fpsimd_last_state, C) := X;
X->thread.fpsimd_state.cpu := C;
3) X exits, causing X's task_struct to be freed.
4) P forks a new child T, which obtains X's recycled task_struct.
T == X.
T->thread.fpsimd_state.cpu == C (inherited from P).
5) T is scheduled on C.
T's fpsimd state is not loaded, because
per_cpu(fpsimd_last_state, C) == T (== X) &&
T->thread.fpsimd_state.cpu == C.
(This is the check performed by fpsimd_thread_switch().)
So, T gets X's registers because the last registers loaded onto C
were those of X, in (2).
This patch fixes the problem by ensuring that the sched-in check
fails in (5): fpsimd_flush_task_state(T) is called when T is
forked, so that T->thread.fpsimd_state.cpu == C cannot be true.
This relies on the fact that T is not schedulable until after
copy_thread() completes.
Once T's fpsimd state has been loaded on some CPU C there may still
be other cpus D for which per_cpu(fpsimd_last_state, D) ==
&X->thread.fpsimd_state. But D is necessarily != C in this case,
and the check in (5) must fail.
An alternative fix would be to do refcounting on task_struct. This
would result in each CPU holding a reference to the last task whose
fpsimd state was loaded there. It's not clear whether this is
preferable, and it involves higher overhead than the fix proposed
in this patch. It would also move all the task_struct freeing
work into the context switch critical section, or otherwise some
deferred cleanup mechanism would need to be introduced, neither of
which seems obviously justified.
Fixes: 005f78cd88 ("arm64: defer reloading a task's FPSIMD state to userland resume")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: word-smithed the comment so it makes more sense]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d59d51f088 upstream.
This fixes CVE-2017-1000407.
KVM allows guests to directly access I/O port 0x80 on Intel hosts. If
the guest floods this port with writes it generates exceptions and
instability in the host kernel, leading to a crash. With this change
guest writes to port 0x80 on Intel will behave the same as they
currently behave on AMD systems.
Prevent the flooding by removing the code that sets port 0x80 as a
passthrough port. This is essentially the same as upstream patch
99f85a28a7, except that patch was
for AMD chipsets and this patch is for Intel.
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Fixes: fdef3ad1b3 ("KVM: VMX: Enable io bitmaps to avoid IO port 0x80 VMEXITs")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5553b142be upstream.
VTTBR_BADDR_MASK is used to sanity check the size and alignment of the
VTTBR address. It seems to currently be off by one, thereby only
allowing up to 39-bit addresses (instead of 40-bit) and also
insufficiently checking the alignment. This patch fixes it.
This patch is the 32bit pendent of Kristina's arm64 fix, and
she deserves the actual kudos for pinpointing that one.
Fixes: f7ed45be3b ("KVM: ARM: World-switch implementation")
Reported-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26aa7b3b1c upstream.
VTTBR_BADDR_MASK is used to sanity check the size and alignment of the
VTTBR address. It seems to currently be off by one, thereby only
allowing up to 47-bit addresses (instead of 48-bit) and also
insufficiently checking the alignment. This patch fixes it.
As an example, with 4k pages, before this patch we have:
PHYS_MASK_SHIFT = 48
VTTBR_X = 37 - 24 = 13
VTTBR_BADDR_SHIFT = 13 - 1 = 12
VTTBR_BADDR_MASK = ((1 << 35) - 1) << 12 = 0x00007ffffffff000
Which is wrong, because the mask doesn't allow bit 47 of the VTTBR
address to be set, and only requires the address to be 12-bit (4k)
aligned, while it actually needs to be 13-bit (8k) aligned because we
concatenate two 4k tables.
With this patch, the mask becomes 0x0000ffffffffe000, which is what we
want.
Fixes: 0369f6a34b ("arm64: KVM: EL2 register definitions")
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 371b80447f upstream.
kexec can leave MMU registers set when booting into a new kernel,
the PIDR (Process Identification Register) in particular. The boot
sequence does not zero PIDR, so it only gets set when CPUs first
switch to a userspace processes (until then it's running a kernel
thread with effective PID = 0).
This leaves a window where a process table entry and page tables are
set up due to user processes running on other CPUs, that happen to
match with a stale PID. The CPU with that PID may cause speculative
accesses that address quadrant 0 (aka userspace addresses), which will
result in cached translations and PWC (Page Walk Cache) for that
process, on a CPU which is not in the mm_cpumask and so they will not
be invalidated properly.
The most common result is the kernel hanging in infinite page fault
loops soon after kexec (usually in schedule_tail, which is usually the
first non-speculative quadrant 0 access to a new PID) due to a stale
PWC. However being a stale translation error, it could result in
anything up to security and data corruption problems.
Fix this by zeroing out PIDR at boot and kexec.
Fixes: 7e381c0ff6 ("powerpc/mm/radix: Add mmu context handling callback for radix")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca76ec9ca8 upstream.
All skey functions call skey_check_enable at their start, which checks
if we are in the PSTATE and injects a privileged operation exception
if we are.
Unfortunately they continue processing afterwards and perform the
operation anyhow as skey_check_enable does not deliver an error if the
exception injection was successful.
Let's move the PSTATE check into the skey functions and exit them on
such an occasion, also we now do not enable skey handling anymore in
such a case.
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: a7e19ab ("KVM: s390: handle missing storage-key facility")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e779498df5 upstream.
When wiring up the socket system calls the compat entries were
incorrectly set. Not all of them point to the corresponding compat
wrapper functions, which clear the upper 33 bits of user space
pointers, like it is required.
Fixes: 977108f89c ("s390: wire up separate socketcalls system calls")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1394e745b upstream.
Implementation of the unpinned APIC page didn't update the VMCS address
cache when invalidation was done through range mmu notifiers.
This became a problem when the page notifier was removed.
Re-introduce the arch-specific helper and call it from ...range_start.
Reported-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Fixes: 38b9917350 ("kvm: vmx: Implement set_apic_access_page_addr")
Fixes: 369ea8242c ("mm/rmap: update to new mmu_notifier semantic v2")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@hotmail.com>
Tested-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddec3bdee0 upstream.
acpi_os_get_root_pointer() may return a valid address even if acpi_disabled
is set, but the host bridge information from the ACPI tables is not going
to be used in that case and the Broadcom host bridge initialization should
not be skipped then, So make broadcom_postcore_init() check acpi_disabled
too to avoid this issue.
Fixes: 6361d72b04 (x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan)
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Link: https://lkml.kernel.org/r/3186627.pxZj1QbYNg@aspire.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c833368f0 ]
I got the following calltrace on a Apollo Lake SoC with 32-bit kernel:
WARNING: CPU: 2 PID: 261 at arch/x86/include/asm/fpu/internal.h:363 fpu__restore+0x1f5/0x260
[...]
Hardware name: Intel Corp. Broxton P/NOTEBOOK, BIOS APLIRVPA.X64.0138.B35.1608091058 08/09/2016
Call Trace:
dump_stack()
__warn()
? fpu__restore()
warn_slowpath_null()
fpu__restore()
__fpu__restore_sig()
fpu__restore_sig()
restore_sigcontext.isra.9()
sys_sigreturn()
do_int80_syscall_32()
entry_INT80_32()
The reason is that a #GP occurs when executing XRSTORS. The root cause
is that we forget to set the xcomp_bv when we fake up the XSAVES area
in the copyin_to_xsaves() function.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-cheng Yu <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/1485075023-30161-1-git-send-email-haokexin@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 475113d937 ]
It's possible to set up PEBS events to get only errors and not
any data, like on SNB-X (model 45) and IVB-EP (model 62)
via 2 perf commands running simultaneously:
taskset -c 1 ./perf record -c 4 -e branches:pp -j any -C 10
This leads to a soft lock up, because the error path of the
intel_pmu_drain_pebs_nhm() does not account event->hw.interrupt
for error PEBS interrupts, so in case you're getting ONLY
errors you don't have a way to stop the event when it's over
the max_samples_per_tick limit:
NMI watchdog: BUG: soft lockup - CPU#22 stuck for 22s! [perf_fuzzer:5816]
...
RIP: 0010:[<ffffffff81159232>] [<ffffffff81159232>] smp_call_function_single+0xe2/0x140
...
Call Trace:
? trace_hardirqs_on_caller+0xf5/0x1b0
? perf_cgroup_attach+0x70/0x70
perf_install_in_context+0x199/0x1b0
? ctx_resched+0x90/0x90
SYSC_perf_event_open+0x641/0xf90
SyS_perf_event_open+0x9/0x10
do_syscall_64+0x6c/0x1f0
entry_SYSCALL64_slow_path+0x25/0x25
Add perf_event_account_interrupt() which does the interrupt
and frequency checks and call it from intel_pmu_drain_pebs_nhm()'s
error path.
We keep the pending_kill and pending_wakeup logic only in the
__perf_event_overflow() path, because they make sense only if
there's any data to deliver.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1482931866-6018-2-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657279778a ]
OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.
The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.
The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3ac350793 ]
Commit 485fa1261f ("ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth")
set the wrong baud rate for the UART. The Baud rate was 300,000 and it should
be 3,000,000 for WL1283.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da20ab3518 ]
We do not have tracepoints for sys_modify_ldt() because we define
it directly instead of using the normal SYSCALL_DEFINEx() macros.
However, there is a reason sys_modify_ldt() does not use the macros:
it has an 'int' return type instead of 'unsigned long'. This is
a bug, but it's a bug cemented in the ABI.
What does this mean? If we return -EINVAL from a function that
returns 'int', we have 0x00000000ffffffea in %rax. But, if we
return -EINVAL from a function returning 'unsigned long', we end
up with 0xffffffffffffffea in %rax, which is wrong.
To work around this and maintain the 'int' behavior while using
the SYSCALL_DEFINEx() macros, so we add a cast to 'unsigned int'
in both implementations of sys_modify_ldt().
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171018172107.1A79C532@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f55ab8f275 ]
The m68k pg_data_table is a fix size array defined in arch/m68k/mm/init.c.
Index numbers within it are defined based on memory size. But for Coldfire
these don't take into account a non-zero physical RAM base address, and this
causes us to access past the end of this array at system start time.
Change the node shift calculation so that we keep the index inside its range.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48070c7305 ]
As of today QEMU does not provide the AIS facility to its guest. This
prevents Linux guests from using PCI devices as the ais facility is
checked during init. As this is just a performance optimization, we can
move the ais check into the code where we need it (calling the SIC
instruction). This is used at initialization and on interrupt. Both
places do not require any serialization, so we can simply skip the
instruction.
Since we will now get all interrupts, we can also avoid the 2nd scan.
As we can have multiple interrupts in parallel we might trigger spurious
irqs more often for the non-AIS case but the core code can handle that.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d9047f8b9 upstream.
Free data structures required for runtime instrumentation from
arch_release_task_struct(). This allows to simplify the code a bit,
and also makes the semantics a bit easier: arch_release_task_struct()
is never called from the task that is being removed.
In addition this allows to get rid of exit_thread() in a later patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0d794d0d01 which is
commit 0d794d0d01 upstream.
Andy writes:
I think the thing to do is to revert the patch from -stable.
The bug it fixes is very minor, and the regression is that it
made a pre-existing bug in some nearly-undebuggable core resume
code much easier to hit. I don't feel comfortable with a
backport of the latter fix until it has a good long soak in
Linus' tree.
Reported-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12806ba937 upstream.
In x2apic mode the LDR is fixed based on the ID rather
than separately loadable like it was before x2.
When kvm_apic_set_state is called, the base is set, and if
it has the X2APIC_ENABLE flag set then the LDR is calculated;
however that value gets overwritten by the memcpy a few lines
below overwriting it with the value that came from userland.
The symptom is a lack of EOI after loading the state
(e.g. after a QEMU migration) and is due to the EOI bitmap
being wrong due to the incorrect LDR. This was seen with
a Win2016 guest under Qemu with irqchip=split whose USB mouse
didn't work after a VM migration.
This corresponds to RH bug:
https://bugzilla.redhat.com/show_bug.cgi?id=1502591
Reported-by: Yiqian Wei <yiwei@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
[Applied fixup from Liran Alon. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e872fa9466 upstream.
Split out the ldr calculation from kvm_apic_set_x2apic_id
since we're about to reuse it in the following patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ea6e84309 upstream.
Sometimes, a processor might execute an instruction while another
processor is updating the page tables for that instruction's code page,
but before the TLB shootdown completes. The interesting case happens
if the page is in the TLB.
In general, the processor will succeed in executing the instruction and
nothing bad happens. However, what if the instruction is an MMIO access?
If *that* happens, KVM invokes the emulator, and the emulator gets the
updated page tables. If the update side had marked the code page as non
present, the page table walk then will fail and so will x86_decode_insn.
Unfortunately, even though kvm_fetch_guest_virt is correctly returning
X86EMUL_PROPAGATE_FAULT, x86_decode_insn's caller treats the failure as
a fatal error if the instruction cannot simply be reexecuted (as is the
case for MMIO). And this in fact happened sometimes when rebooting
Windows 2012r2 guests. Just checking ctxt->have_exception and injecting
the exception if true is enough to fix the case.
Thanks to Eduardo Habkost for helping in the debugging of this issue.
Reported-by: Yanan Fu <yfu@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cb57c9ed upstream.
Instruction emulation after trapping a #UD exception can result in an
MMIO access, for example when emulating a MOVBE on a processor that
doesn't support the instruction. In this case, the #UD vmexit handler
must exit to user mode, but there wasn't any code to do so. Add it for
both VMX and SVM.
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51c4b8bba6 upstream.
When guest passes KVM it's pvclock-page GPA via WRMSR to
MSR_KVM_SYSTEM_TIME / MSR_KVM_SYSTEM_TIME_NEW, KVM don't initialize
pvclock-page to some start-values. It just requests a clock-update which
will happen before entering to guest.
The clock-update logic will call kvm_setup_pvclock_page() to update the
pvclock-page with info. However, kvm_setup_pvclock_page() *wrongly*
assumes that the version-field is initialized to an even number. This is
wrong because at first-time write, field could be any-value.
Fix simply makes sure that if first-time version-field is odd, increment
it once more to make it even and only then start standard logic.
This follows same logic as done in other pvclock shared-pages (See
kvm_write_wall_clock() and record_steal_time()).
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3ac350793 upstream.
Commit 485fa1261f ("ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth")
set the wrong baud rate for the UART. The Baud rate was 300,000 and it should
be 3,000,000 for WL1283.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7ace5ed88 upstream.
Fixes commit 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56322e1232 upstream.
Fix commit 05c4ffc3a2 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cabab3f9f5 ]
s390 version of commit 334bb77387 ("x86/kbuild: enable modversions
for symbols exported from asm") so we get also rid of all these
warnings:
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memcpy" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memmove" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memset" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "save_fpu_regs" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie64a" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie_exit" [vmlinux] version generation failed, symbol will not be versioned.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46725b17f1 upstream.
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes: 129b69df9c ("powerpc: Use get_signal() signal_setup_done()")
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05f016d2ca upstream.
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15038e1472 upstream.
For many years some users of assigned devices have reported worse
performance on AMD processors with NPT than on AMD without NPT,
Intel or bare metal.
The reason turned out to be that SVM is discarding the guest PAT
setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-,
PA3=UC). The guest might be using a different setting, and
especially might want write combining but isn't getting it
(instead getting slow UC or UC- accesses).
Thanks a lot to geoff@hostfission.com for noticing the relation
to the g_pat setting. The patch has been tested also by a bunch
of people on VFIO users forums.
Fixes: 709ddebf81
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Nick Sarnie <commendsarnex@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21f2d55118 upstream.
Intel SDM 27.5.2 Loading Host Segment and Descriptor-Table Registers:
"The GDTR and IDTR limits are each set to FFFFH."
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56a46acf62 upstream.
The WLAN LED on the Linksys WRT54GSv1 is active low, but the software
treats it as active high. Fix the inverted logic.
Fixes: 7bb26b1691 ("MIPS: BCM47xx: Fix LEDs on WRT54GS V1.0")
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Looks-ok-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16071/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 547da67317 upstream.
Fix a commit 7aeb753b53 ("MIPS: Implement task_user_regset_view.")
regression, then activated by commit 6a9c001b7e ("MIPS: Switch ELF
core dumper to use regsets.)", that caused n32 processes to dump o32
core files by failing to set the EF_MIPS_ABI2 flag in the ELF core file
header's `e_flags' member:
$ file tls-core
tls-core: ELF 32-bit MSB executable, MIPS, N32 MIPS64 rel2 version 1 (SYSV), [...]
$ ./tls-core
Aborted (core dumped)
$ file core
core: ELF 32-bit MSB core file MIPS, MIPS-I version 1 (SYSV), SVR4-style
$
Previously the flag was set as the result of a:
statement placed in arch/mips/kernel/binfmt_elfn32.c, however in the
regset case, i.e. when CORE_DUMP_USE_REGSET is set, ELF_CORE_EFLAGS is
no longer used by `fill_note_info' in fs/binfmt_elf.c, and instead the
`->e_flags' member of the regset view chosen is. We have the views
defined in arch/mips/kernel/ptrace.c, however only an o32 and an n64
one, and the latter is used for n32 as well. Consequently an o32 core
file is incorrectly dumped from n32 processes (the ELF32 vs ELF64 class
is chosen elsewhere, and the 32-bit one is correctly selected for n32).
Correct the issue then by defining an n32 regset view and using it as
appropriate. Issue discovered in GDB testing.
Fixes: 7aeb753b53 ("MIPS: Implement task_user_regset_view.")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Djordje Todorovic <djordje.todorovic@rt-rk.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17617/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7fd89a640 upstream.
Building 32-bit MIPS64r2 kernels produces warnings like the following
on certain toolchains (such as GNU assembler 2.24.90, but not GNU
assembler 2.28.51) since commit 22b8ba765a ("MIPS: Fix MIPS64 FP
save/restore on 32-bit kernels"), due to the exposure of fpu_save_16odd
from fpu_save_double and fpu_restore_16odd from fpu_restore_double:
arch/mips/kernel/r4k_fpu.S:47: Warning: float register should be even, was 1
...
arch/mips/kernel/r4k_fpu.S:59: Warning: float register should be even, was 1
...
This appears to be because .set mips64r2 does not change the FPU ABI to
64-bit when -march=mips64r2 (or e.g. -march=xlp) is provided on the
command line on that toolchain, from the default FPU ABI of 32-bit due
to the -mabi=32. This makes access to the odd FPU registers invalid.
Fix by explicitly changing the FPU ABI with .set fp=64 directives in
fpu_save_16odd and fpu_restore_16odd, and moving the undefine of fp up
in asmmacro.h so fp doesn't turn into $30.
Fixes: 22b8ba765a ("MIPS: Fix MIPS64 FP save/restore on 32-bit kernels")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17656/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05a67cc258 upstream.
There is a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Fixes: 53263a1c68 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16047/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ef4b43cd3 upstream.
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
Fixes: 53263a1c68 ("MIPS: ralink: add mt7628an support")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16046/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b0c0c922f upstream.
When CONFIG_ARM_LPAE is set, the PMD dump relies on the software
read-only bit to determine whether a page is writable. This
concealed a bug which left the kernel text section writable
(AP2=0) while marked read-only in the software bit.
In a kernel with the AP2 bug, the dump looks like this:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M ro x SHD
0xc0600000-0xc0800000 2M ro NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
The fix is to check that the software and hardware bits are both
set before displaying "ro". The dump then shows the true perms:
---[ Kernel Mapping ]---
0xc0000000-0xc0200000 2M RW NX SHD
0xc0200000-0xc0600000 4M RW x SHD
0xc0600000-0xc0800000 2M RW NX SHD
0xc0800000-0xc4800000 64M RW NX SHD
Fixes: ded9477984 ("ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE")
Signed-off-by: Philip Derrin <philip@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 400eeffaff upstream.
Currently, for ARM kernels with CONFIG_ARM_LPAE and
CONFIG_STRICT_KERNEL_RWX enabled, the 2MiB pages mapping the
kernel code and rodata are writable. They are marked read-only in
a software bit (L_PMD_SECT_RDONLY) but the hardware read-only bit
is not set (PMD_SECT_AP2).
For user mappings, the logic that propagates the software bit
to the hardware bit is in set_pmd_at(); but for the kernel,
section_update() writes the PMDs directly, skipping this logic.
The fix is to set PMD_SECT_AP2 for read-only sections in
section_update(), at the same time as L_PMD_SECT_RDONLY.
Fixes: 1e3479225a ("ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error")
Signed-off-by: Philip Derrin <philip@cog.systems>
Reported-by: Neil Dick <neil@cog.systems>
Tested-by: Neil Dick <neil@cog.systems>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6218f96c58 upstream.
The generic pte_access_permitted() implementation only checks for
pte_present() (together with the write permission where applicable).
However, for both kernel ptes and PROT_NONE mappings pte_present() also
returns true on arm64 even though such mappings are not user accessible.
Additionally, arm64 now supports execute-only user permission
(PROT_EXEC) which is implemented by clearing the PTE_USER bit.
With this patch the arm64 implementation of pte_access_permitted()
checks for the PTE_VALID and PTE_USER bits together with writable access
if applicable.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca37e57bbe upstream.
Running this code with IRQs enabled (where dummy_lock is a spinlock):
static void check_load_gs_index(void)
{
/* This will fail. */
load_gs_index(0xffff);
spin_lock(&dummy_lock);
spin_unlock(&dummy_lock);
}
Will generate a lockdep warning. The issue is that the actual write
to %gs would cause an exception with IRQs disabled, and the exception
handler would, as an inadvertent side effect, update irqflag tracing
to reflect the IRQs-off status. native_load_gs_index() would then
turn IRQs back on and return with irqflag tracing still thinking that
IRQs were off. The dummy lock-and-unlock causes lockdep to notice the
error and warn.
Fix it by adding the missing tracing.
Apparently nothing did this in a context where it mattered. I haven't
tried to find a code path that would actually exhibit the warning if
appropriately nasty user code were running.
I suspect that the security impact of this bug is very, very low --
production systems don't run with lockdep enabled, and the warning is
mostly harmless anyway.
Found during a quick audit of the entry code to try to track down an
unrelated bug that Ingo found in some still-in-development code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/e1aeb0e6ba8dd430ec36c8a35e63b429698b4132.1511411918.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12a78d43de upstream.
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c
Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked 1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
000 001 010 011 100 101 110 111
TEST Ib/Iz,(undefined),NOT,NEG,MUL AL/rAX,IMUL AL/rAX,DIV AL/rAX,IDIV AL/rAX
So, it seems TEST Ib is assigned to 001.
Add the new pattern.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb0631fd3c upstream.
Syzkaller with KASAN has reported a use-after-free of vma->vm_flags in
__do_page_fault() with the following reproducer:
mmap(&(0x7f0000000000/0xfff000)=nil, 0xfff000, 0x3, 0x32, 0xffffffffffffffff, 0x0)
mmap(&(0x7f0000011000/0x3000)=nil, 0x3000, 0x1, 0x32, 0xffffffffffffffff, 0x0)
r0 = userfaultfd(0x0)
ioctl$UFFDIO_API(r0, 0xc018aa3f, &(0x7f0000002000-0x18)={0xaa, 0x0, 0x0})
ioctl$UFFDIO_REGISTER(r0, 0xc020aa00, &(0x7f0000019000)={{&(0x7f0000012000/0x2000)=nil, 0x2000}, 0x1, 0x0})
r1 = gettid()
syz_open_dev$evdev(&(0x7f0000013000-0x12)="2f6465762f696e7075742f6576656e742300", 0x0, 0x0)
tkill(r1, 0x7)
The vma should be pinned by mmap_sem, but handle_userfault() might (in a
return to userspace scenario) release it and then acquire again, so when
we return to __do_page_fault() (with other result than VM_FAULT_RETRY),
the vma might be gone.
Specifically, per Andrea the scenario is
"A return to userland to repeat the page fault later with a
VM_FAULT_NOPAGE retval (potentially after handling any pending signal
during the return to userland). The return to userland is identified
whenever FAULT_FLAG_USER|FAULT_FLAG_KILLABLE are both set in
vmf->flags"
However, since commit a3c4fb7c9c ("x86/mm: Fix fault error path using
unsafe vma pointer") there is a vma_pkey() read of vma->vm_flags after
that point, which can thus become use-after-free. Fix this by moving
the read before calling handle_mm_fault().
Reported-by: syzbot <bot+6a5269ce759a7bb12754ed9622076dc93f65a1f6@syzkaller.appspotmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Fixes: 3c4fb7c9c2e ("x86/mm: Fix fault error path using unsafe vma pointer")
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c50538752 upstream.
The e7 opcode table does not have an end marker. Hence when trying to
find an unknown e7 instruction the code will access memory behind the
table until it finds something that matches the opcode, or the kernel
crashes, whatever comes first.
This affects not only the in-kernel disassembler but also uprobes and
kprobes which refuse to set a probe on unknown instructions, and
therefore search the opcode tables to figure out if instructions are
known or not.
Fixes: 3585cb0280 ("s390/disassembler: add vector instructions")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6e646ad7c upstream.
For PREEMPT enabled kernels the runtime instrumentation (RI) code
contains a possible use-after-free bug. If a task that makes use of RI
exits, it will execute do_exit() while still enabled for preemption.
That function will call exit_thread_runtime_instr() via
exit_thread(). If exit_thread_runtime_instr() gets preempted after the
RI control block of the task has been freed but before the pointer to
it is set to NULL, then save_ri_cb(), called from switch_to(), will
write to already freed memory.
Avoid this and simply disable preemption while freeing the control
block and setting the pointer to NULL.
Fixes: e4b8b3f33f ("s390: add support for runtime instrumentation")
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1c5befc1c upstream.
Dan Horák reported the following crash related to transactional execution:
User process fault: interruption code 0013 ilc:3 in libpthread-2.26.so[3ff93c00000+1b000]
CPU: 2 PID: 1 Comm: /init Not tainted 4.13.4-300.fc27.s390x #1
Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
task: 00000000fafc8000 task.stack: 00000000fafc4000
User PSW : 0705200180000000 000003ff93c14e70
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:1 AS:0 CC:2 PM:0 RI:0 EA:3
User GPRS: 0000000000000077 000003ff00000000 000003ff93144d48 000003ff93144d5e
0000000000000000 0000000000000002 0000000000000000 000003ff00000000
0000000000000000 0000000000000418 0000000000000000 000003ffcc9fe770
000003ff93d28f50 000003ff9310acf0 000003ff92b0319a 000003ffcc9fe6d0
User Code: 000003ff93c14e62: 60e0b030 std %f14,48(%r11)
000003ff93c14e66: 60f0b038 std %f15,56(%r11)
#000003ff93c14e6a: e5600000ff0e tbegin 0,65294
>000003ff93c14e70: a7740006 brc 7,3ff93c14e7c
000003ff93c14e74: a7080000 lhi %r0,0
000003ff93c14e78: a7f40023 brc 15,3ff93c14ebe
000003ff93c14e7c: b2220000 ipm %r0
000003ff93c14e80: 8800001c srl %r0,28
There are several bugs with control register handling with respect to
transactional execution:
- on task switch update_per_regs() is only called if the next task has
an mm (is not a kernel thread). This however is incorrect. This
breaks e.g. for user mode helper handling, where the kernel creates
a kernel thread and then execve's a user space program. Control
register contents related to transactional execution won't be
updated on execve. If the previous task ran with transactional
execution disabled then the new task will also run with
transactional execution disabled, which is incorrect. Therefore call
update_per_regs() unconditionally within switch_to().
- on startup the transactional execution facility is not enabled for
the idle thread. This is not really a bug, but an inconsistency to
other facilities. Therefore enable the facility if it is available.
- on fork the new thread's per_flags field is not cleared. This means
that a child process inherits the PER_FLAG_NO_TE flag. This flag can
be set with a ptrace request to disable transactional execution for
the current process. It should not be inherited by new child
processes in order to be consistent with the handling of all other
PER related debugging options. Therefore clear the per_flags field in
copy_thread_tls().
Reported-and-tested-by: Dan Horák <dan@danny.cz>
Fixes: d35339a42d ("s390: add support for transactional memory")
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
