This report summary monitor the firmware related counters, firmware
version. It will help to analysis the communication between driver and
firmware.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-9-pkshih@realtek.com
The feature can help to know how the firmware mechanism working.
There are several trigger point set in firmware. If driver send
the H2C command to firmware to enable the trigger, firmware will
toggle GPIO to perform the firmware mechanism.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-8-pkshih@realtek.com
To avoid driver I/O, firmware will periodic monitor the register
settings and update to driver. The v7 report adjust the structure
variables order, so driver does changes accordingly.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-7-pkshih@realtek.com
When the PTA breaks Wi-Fi traffic request caused Bluetooth traffic,
it means Bluetooth polluted the Wi-Fi traffic. When Wi-Fi is TX, the
mechanism can ignore the polluted Wi-Fi packet retry counter, it is
help to the stability of Wi-Fi TX rate. The chip RTL8922A has not only
one MAC, so need to include the all MAC as reference.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-6-pkshih@realtek.com
PTA(packet traffic arbitration) is a coexistence hardware feature.
Wi-Fi & Bluetooth owns their PTA, the function is to show whose PTA
control the traffic now. RTL8922A PTA control is controlled by hardware
logic, there is no register to monitor the setting.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-5-pkshih@realtek.com
The map is the H2C index for driver forward the driver status to firmware.
The status is for firmware to make mechanism decision, if driver provided
the wrong index to firmware, it will make parse the status incorrectly.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-4-pkshih@realtek.com
To support v7 version firmware cycle report, which adjusts the structure
variables order, apply the related structure and functions. The cycle
report can show how the firmware mechanism runs.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-3-pkshih@realtek.com
The Wi-Fi/Bluetooth slot are toggled by firmware timer when Wi-Fi doing
firmware scan, and Wi-Fi slot don't allow Bluetooth do traffic when
Wi-Fi slot. It will trigger Bluetooth audio lag in a random rate, because
Bluetooth can not have enough time slot to keep enough data to play audio.
This patch make Bluetooth can do traffic during Wi-Fi slot, this can help
Bluetooth to collect audio data in time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-2-pkshih@realtek.com
Software control (on/off) and hardware control (automatic blinking)
tested with EDUP EP-N8568.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/7df66d1f-87a1-4f44-9aac-ce75438abde3@gmail.com
We want the tty fixes in here as well, and it resolves a merge conflict
in:
drivers/tty/serial/serial_core.c
as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
slab_out_of_memory() uses count_partial() to get the exact count
of free objects for each node. As it may get called in the slab
allocation path, count_partial_free_approx() can be used to avoid
the risk and overhead of traversing a long partial slab list.
At the same time, show_slab_objects() still uses count_partial().
Thus, slub users can still have the option to access the exact
count of objects via sysfs if the overhead is acceptable to them.
Signed-off-by: Jianfeng Wang <jianfeng.w.wang@oracle.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
When reading "/proc/slabinfo", the kernel needs to report the number
of free objects for each kmem_cache. The current implementation uses
count_partial() to get it by scanning each kmem_cache_node's partial
slab list and summing free objects from every partial slab. This
process must hold per-kmem_cache_node spinlock and disable IRQ, and
may take a long time. Consequently, it can block slab allocations on
other CPUs and cause timeouts for network devices, when the partial
list is long. In production, even NMI watchdog can be triggered due
to this matter: e.g., for "buffer_head", the number of partial slabs
was observed to be ~1M in one kmem_cache_node. This problem was also
confirmed by others [1-3].
Iterating a partial list to get the exact count of objects can cause
soft lockups for a long list with or without the lock (e.g., if
preemption is disabled), and may not be very useful: the object count
can change after the lock is released. The approach of maintaining
free-object counters requires atomic operations on the fast path [3].
So, the fix is to introduce count_partial_free_approx(). This function
can be used for getting the free object count in a kmem_cache_node's
partial list. It limits the number of slabs to scan and avoids scanning
the whole list by giving an approximation for a long list. Suppose the
limit is N. If the list's length is not greater than N, output the exact
count by traversing the list; if its length is greater than N, output an
approximated count by traversing a subset of the list. The proposed
method is to scan N/2 slabs from the list's head and N/2 slabs from
the tail. For a partial list with ~280K slabs, benchmarks show that
it performs better than just counting from the list's head, after slabs
get sorted by kmem_cache_shrink(). Default the limit to 10000, as it
produces an approximation within 1% of the exact count for both
scenarios. Then, use count_partial_free_approx() in get_slabinfo().
Benchmarks: Diff = (exact - approximated) / exact
* Normal case (w/o kmem_cache_shrink()):
| MAX_TO_SCAN | Diff (count from head)| Diff (count head+tail)|
| 1000 | 0.43 % | 1.09 % |
| 5000 | 0.06 % | 0.37 % |
| 10000 | 0.02 % | 0.16 % |
| 20000 | 0.009 % | -0.003 % |
* Skewed case (w/ kmem_cache_shrink()):
| MAX_TO_SCAN | Diff (count from head)| Diff (count head+tail)|
| 1000 | 12.46 % | 6.75 % |
| 5000 | 5.38 % | 1.27 % |
| 10000 | 4.99 % | 0.22 % |
| 20000 | 4.86 % | -0.06 % |
[1] https://lore.kernel.org/linux-mm/alpine.DEB.2.21.2003031602460.1537@www.lameter.com/T/
[2] https://lore.kernel.org/lkml/alpine.DEB.2.22.394.2008071258020.55871@www.lameter.com/T/
[3] https://lore.kernel.org/lkml/1e01092b-140d-2bab-aeba-321a74a194ee@linux.com/T/
Signed-off-by: Jianfeng Wang <jianfeng.w.wang@oracle.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Alex Elder says:
====================
net: ipa: eight simple cleanups
This series contains a mix of cleanups, some dating back to
December, 2022. Version 1 was based on an older version of
net-next/main; this version has simply been rebased.
The first two make it so the IPA SUSPEND interrupt only gets enabled
when necessary. That make it possible in the third patch to call
device_init_wakeup() during an earlier phase of initialization, and
remove two functions.
The next patch removes IPA register definitions that are never used.
The fifth patch makes ipa_table_hash_support() a real function, so
the IPA structure only needs to be declared rather than defined when
that file is parsed.
The sixth patch fixes improper argument names in two function
declarations. The seventh removes the declaration for a function
that does not exist, and makes ipa_cmd_init() actually get called.
And the last one eliminates ipa_version_supported(), in favor of
just deciding that if a device is probed because its compatible
matches, that device is assumed to be supported.
====================
Link: https://lore.kernel.org/r/20240419151800.2168903-1-elder@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only place ipa_version_supported() is called is in the probe
function. The version comes from the match data. Rather than
checking the version validity separately, just consider anything
that has match data to be supported.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In "ipa_cmd.h", ipa_cmd_data_valid() is declared, but that function
does not exist. So delete that declaration.
Also, for some reason ipa_cmd_init() never gets called. It isn't
really critical--it just validates that some memory offsets and a
size can be represented in some register fields, and they won't fail
with current data. Regardless, call the function in ipa_probe().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In "ipa_endpoint.h", two function declarations have bogus argument
names. Fix these.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With the exception of ipa_table_hash_support(), nothing defined in
"ipa_table.h" requires the full definition of the IPA structure.
Change that function to be a "real" function rather than an inline,
to avoid requring the IPA structure to be defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The FILT_ROUT_HASH_EN register is only used for IPA v4.2. There,
routing and filter table hashing are not supported, and so the
register must be written to disable the feature. No other version
uses this register, so its definition can be removed. If we need to
use these some day (for example, explicitly enable the feature) this
commit can be reverted.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, enabling wakeup for the IPA device doesn't occur until
the setup phase of initialization (in ipa_power_setup()).
There is no need to delay doing that, however. We can conveniently
do it during the config phase, in ipa_interrupt_config(), where we
enable power management wakeup mode for the IPA interrupt.
Moving the device_init_wakeup() out of ipa_power_setup() leaves that
function empty, so it can just be eliminated.
Similarly, rearrange all of the matching inverse calls, disabling
device wakeup in ipa_interrupt_deconfig() and removing that function
as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Only enable the SUSPEND IPA interrupt type when at least one
endpoint has that interrupt enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Keep track of which endpoints have the SUSPEND IPA interrupt enabled
in a variable-length bitmap. This will be used in the next patch to
allow the SUSPEND interrupt type to be disabled except when needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Also, don't set bit 7 of LEDCFG2 for RTL8192CU. If bit 7 is set the LED
never turns on. In this family only RTL8188CUS needs bit 7 of LEDCFG2
set.
Software control (on/off) and hardware control (automatic blinking)
tested with Netcore NW362 (RTL8192CU).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4b5970cf-d28b-415a-b911-82cdb5e9ce99@gmail.com
Until now RTL8192CU family was using the MAC init table from RTL8723AU,
but these tables are not identical in the two vendor drivers. Import
the correct table for RTL8192CU.
Also move the existing MAC init table to rtl8xxxu_8723a.c, which is
the only remaining user.
Tested with the Netcore NW362 (RTL8192CU).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/a53ed8b9-27fc-4871-a20a-ad42c6d210d3@gmail.com
The Loongson-2K2000 and Loongson-2K1000 have similar thermal sensors,
except that the temperature is read differently.
In particular, the temperature output registers of the Loongson-2K2000
are defined in the chip configuration domain and are read in a different
way.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/fdbfdcc3231a36a4ee0bcf1377ddcbd6f8c944b5.1713837379.git.zhoubinbin@loongson.cn
The temperature output register of the Loongson-2K2000 is defined in the
chip configuration domain, which is different from the Loongson-2K1000,
so it can't be fallbacked.
We need to use two groups of registers to describe it: the first group
is the high and low temperature threshold setting register; the second
group is the temperature output register.
It is true that this fix will cause ABI corruption, but it is necessary
otherwise the Loongson-2K2000 temperature sensor will not work properly.
Fixes: 72684d99a8 ("thermal: dt-bindings: add loongson-2 thermal")
Cc: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5198999d679f1a1c3457385acb9fadfc85da1f1e.1713837379.git.zhoubinbin@loongson.cn
The thermal on the Loongson-2K0500 shares the design with the
Loongson-2K1000. Define corresponding compatible string, having the
loongson,ls2k1000-thermal as a fallback.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/26524a63abd2d032e4c45efe6ce3fedb46841768.1713837379.git.zhoubinbin@loongson.cn
Some systems don't always populate sensor controller slots starting
at slot 0. Use a bitmap instead of a count to indicate valid sensor
slots. Also create a pretty iterator for that.
About that iterator: it causes checkpatch to complain with "ERROR:
Macros with multiple statements should be enclosed in a do - while
loop". However this is not possible here. And many similar iterators
do exist using the same form in the tree already.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-12-nico@fluxnic.net
The golden temperature calibration value in nvram is not always the
3rd byte. A future commit will prove this assumption wrong.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-11-nico@fluxnic.net
Current code assumes calibration values are always stored contiguously
in host endian order. A future patch will prove this wrong.
Let's specify the offset for each calibration byte instead.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-5-nico@fluxnic.net
All the .hw_tshut_temp instances are initialized with the same value.
Let's remove those and use a common definition instead. If ever a
different value must be used in the future then an override parameter
could be added back.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-4-nico@fluxnic.net
Move efuse data interpretation inside lvts_golden_temp_init() alongside
the actual code retrieving wanted value.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-3-nico@fluxnic.net
Calibration values are 24-bit wide. Those values so far appear to span
only 16 bits but let's not push our luck.
Found while looking at the original Mediatek driver code.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-2-nico@fluxnic.net
compute_intercept_slope() is called from calibrate_8960() (in tsens-8960.c)
as compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB) which lead to null
pointer dereference (if DEBUG or DYNAMIC_DEBUG set).
Fix this bug by adding null pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: dfc1193d4d ("thermal/drivers/tsens: Replace custom 8960 apis with generic apis")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240411114021.12203-1-amishin@t-argos.ru
In order for lvts_raw_to_temp to function properly on mt8192,
temperature coefficients for mt8192 need to be added.
Fixes: 288732242d ("thermal/drivers/mediatek/lvts_thermal: Add mt8192 support")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240416-lvts_thermal-v2-1-f8a36882cc53@chromium.org
The initial driver used a formula to approximate the temperature and
register values reversed engineered from an out-of-tree BSP driver. This
was needed as the datasheet at the time did not contain any information
on how to do this. Later Gen3 (Rev 2.30) and Gen4 (all) now contains
this information.
Update the approximation formula to use the datasheet's information
instead of the reversed-engineered one.
On an idle M3-N without fused calibration values for PTAT and THCODE the
old formula reports,
zone0: 52000
zone1: 53000
zone2: 52500
While the new formula under the same circumstances reports,
zone0: 52500
zone1: 54000
zone2: 54000
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240327133013.3982199-3-niklas.soderlund+renesas@ragnatech.se
The calculated Tj_T constant is calculated from the PTAT data either
read from the first TSC zone on the device if calibration data is fused,
or from fallback values in the driver itself. The value calculated is
shared among all TSC zones.
Move the Tj_T constant to the shared private data structure instead of
duplicating it in each TSC private data. This requires adding a pointer
to the shared data to the TSC private data structure. This back pointer
make it easier to further rework the temperature conversion logic.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240327133013.3982199-2-niklas.soderlund+renesas@ragnatech.se
In comparison to other Amlogic chips, there is one key difference.
The offset for the sec_ao base, also known as u_efuse_off, is special,
while other aspects remain the same.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240328191322.17551-3-ddrokosov@salutedevices.com
Provide right compatible properties for Amlogic A1 Thermal Sensor
controller. A1 family supports only one thermal node - CPU thermal
sensor.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240328191322.17551-2-ddrokosov@salutedevices.com
As part of suspend to RAM, tsens hardware will be turned off.
While resume callback, re-initialize tsens hardware.
Signed-off-by: Priyansh Jain <quic_priyjain@quicinc.com>
Acked-by: Amit Kucheria <amitk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240328050230.31770-1-quic_priyjain@quicinc.com
