The get_stream_position has been replaced by get_dai_frame_counter, it
should not be set to allow it to be dropped from core code.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the new callback to retrieve the DAI (link) frame counter.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add implementation for reading the LDP (Linear DMA Position) to be used as
get_host_byte_counter().
The LDP is counting the number of bytes moved between the DSP and host
memory.
Set the get_dai_frame_counter to hda_dsp_get_stream_llp, which is counting
the frames on the link side of the DSP.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For delay calculation we need two information:
Number of bytes transferred between the DSP and host memory (ALSA buffer)
Number of frames transferred between the DSP and external device
(link/codec/DMIC/etc).
The reason for the different units (bytes vs frames) on host and dai side
is that the format on the dai side is decided by the firmware and might
not be the same as on the host side, thus the expectation is that the
counter reflects the number of frames.
The kernel know the host side format and in there we have access to the
DMA position which is in bytes.
In a simplified way, the DSP caused delay is the difference between the
two counters.
The existing get_stream_position callback is defined to retrieve the frame
counter on the DAI side but it's name is too generic to be intuitive and
makes it hard to define a callback for the host side.
This patch introduces a new set of callbacks to replace the
get_stream_position and define the host side equivalent:
get_dai_frame_counter
get_host_byte_counter
Subsequent patches will remove the old callback.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the MTL mtl_dsp_get_stream_hda_link_position() function and related
defines since it can only work on platforms which have 19 streams because
of the use of 0x948 as base offset for the LLP registers.
The generic hda_dsp_get_stream_hda_link_position() takes the number of
streams into consideration when reading the LLP registers for the stream
and can handle different HDA configurations.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the Linear Link Position is not available in firmware SRAM window we
use the host accessible position registers to read it.
The address of the PPLCLLPL/U registers depend on the number of streams
(playback+capture).
At probe time the pplc_addr is calculated for each stream and we can use
it to read the LLP without the need of address re-calculation.
Set the get_stream_position callback in sof_hda_common_ops for all
platforms:
The callback is used for IPC4 delay calculations only but the register is
a generic HDA register, not tied to any specific IPC version.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the PCM have the dsp_max_burst_size_in_ms set then place a constraint
to limit the minimum buffer time to avoid xruns caused by DMA bursts
spinning on the ALSA buffer.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up the pcm widget, save the DSP buffer size (in ms) for
platform code to place a constraint on playback.
On playback the DMA will fill the buffer on start and if the period
size is smaller it will immediately overrun.
On capture the DMA will move data in 1ms bursts.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dsp_max_burst_size_in_ms can be used to save the length of the maximum
burst size in ms the host DMA will use.
Platform code can place constraint using this to avoid user space
requesting too small ALSA buffer which will result xruns.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently, I frequently hit the following test failure:
[root@arch-fb-vm1 bpf]# ./test_progs -n 33/1
test_lookup_update:PASS:skel_open 0 nsec
[...]
test_lookup_update:PASS:sync_rcu 0 nsec
test_lookup_update:FAIL:map1_leak inner_map1 leaked!
#33/1 btf_map_in_map/lookup_update:FAIL
#33 btf_map_in_map:FAIL
In the test, after map is closed and then after two rcu grace periods,
it is assumed that map_id is not available to user space.
But the above assumption cannot be guaranteed. After zero or one
or two rcu grace periods in different siturations, the actual
freeing-map-work is put into a workqueue. Later on, when the work
is dequeued, the map will be actually freed.
See bpf_map_put() in kernel/bpf/syscall.c.
By using workqueue, there is no ganrantee that map will be actually
freed after a couple of rcu grace periods. This patch removed
such map leak detection and then the test can pass consistently.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240322061353.632136-1-yonghong.song@linux.dev
Initialization is completed before adding the component as that can
start the process of the device binding and trigger actions that check
init_done.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240325145510.328378-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The system and amplifier names influence which firmware and tuning files
are downloaded to the device; log these values to aid end-user system
support.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240325142937.257869-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement a helper function to check if an instruction is
addr_space_cast from as(0) to as(1). Use this helper in the x86 JIT.
Other JITs can use this helper when they add support for this instruction.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20240324183226.29674-1-puranjay12@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Complete the example of recommended order of properties by adding
missing address/size-cells. They are not necessary to illustrate the
style, but lack of them us bit really correct DTS code which might
confuse readers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240325091139.18602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Bindings for a given device class generally go to the respective
subsystem maintainers. Add the TPM bindings to the TPM
maintainers entry.
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.ogr>
Link: https://lore.kernel.org/r/20240130215917.2473250-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
get_kernel_nofault() (or, rather, underlying copy_from_kernel_nofault())
is not free and it does pop up in performance profiles when
kprobes are heavily utilized with CONFIG_X86_KERNEL_IBT=y config.
Let's avoid using it if we know that fentry_ip - 4 can't cross page
boundary. We do that by masking lowest 12 bits and checking if they are
Another benefit (and actually what caused a closer look at this part of
code) is that now LBR record is (typically) not wasted on
copy_from_kernel_nofault() call and code, which helps tools like
retsnoop that grab LBR records from inside BPF code in kretprobes.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/20240319212013.1046779-1-andrii@kernel.org
If job accounting is disabled, then both fdinfo's drm-engine and drm-cycle
key values will remain immutable. In that case, it makes more sense not to
display them at all to avoid confusing user space profiling tools.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240316231306.293817-1-adrian.larumbe@collabora.com
To simplify the code, use BPF selftests helper start_server() in
bpf_tcp_ca.c instead of open-coding it. This helper is defined in
network_helpers.c, and exported in network_helpers.h, which is already
included in bpf_tcp_ca.c.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/9926a79118db27dd6d91c4854db011c599cabd0e.1711331517.git.tanggeliang@kylinos.cn
There is a difference between kernel uapi bpf.h and tools
uapi bpf.h. There is no functionality difference, but let
us sync properly to make it easy for later bpf.h update.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240325033842.1693553-1-yonghong.song@linux.dev
All the spi_transfer variables in this file use the name "xfer" except
the one in mtk_spi_interrupt(). Align the naming for consistency and
easier searching.
While at it, reformat one memcpy() usage since the coding style allows
100 column lines today.
This commit has no functional change.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-3-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Extract a magic number, from mt7621_spi_probe(), used to
declare the number of chip select lines (which co-incides
with the native chip select count of 2) to a macro.
Use the newly defined MT7621_NATIVE_CS_COUNT macro to
instead populate both the spi_controller's max_native_cs
and num_chipselect members.
Declare that the spi_controller should use_gpio_descriptors
if present in the device properties (such as those declared
in the cs-gpio property of a "ralink,mt7621-spi" compatible
device-tree node) so that the SPI core will recalculcate
num_chipselect to account for the GPIO descriptors that
it should have populated in the cs_gpiod array member.
Remove the assignment of mt7621_spi_transfer_one_message()
to the spi_controller's transfer_one_message hook.
Refactor the mt7621_spi_transfer_one_message() logic into
mt7621_spi_prepare_message() and mt7621_spi_transfer_one()
and assign both to the spi_controller's prepare_message
and transfer_one hooks respectively.
Migrate the call mt7621_spi_transfer_one_message() made to
mt7621_spi_flush() just before chip select deactivation,
to the end of mt7621_spi_write_half_duplex() to ensure
that any pending data is shifted out of MOSI before the SPI
core deactivates the chip select line.
As chip select activation is now taken care of by the SPI
core, due to the use of the transfer_one hook instead of
transfer_one_message, the calls to mt7621_spi_set_cs()
from mt7621_spi_transfer_one_message() have fallen away.
And although the SPI core will handle activation for GPIO
chip select lines behind the scenes, it requires a callback
to allow the driver to perform controller-specific
operations to control its native chip select lines.
Rename mt7621_spi_set_cs() to mt7621_spi_set_native_cs()
and make sure that it takes into account the activation
polarity of the chip select line it's acting upon, as the
passed enable parameter represents the desired line level
and not the desired activation state, and then assign
mt7621_set_cs() to the spi_controller's set_cs hook.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://msgid.link/r/20240316010302.20776-1-justin.swartz@risingedge.co.za
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change naming from tmp to platform profile to clarify the module may
interact with both the TMP and FAN subystems. Add functionality that
switches the fan profile when the platform profile is changed when
a fan is present.
Signed-off-by: Ivor Wanders <ivor@iwanders.net>
Link: https://github.com/linux-surface/kernel/pull/145
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240314223733.6236-2-ivor@iwanders.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If an error code other than EINVAL, ENODEV or ETIME is returned
by ec_read()/ec_write(), then AE_OK is wrongly returned.
Fix this by only returning AE_OK if the return code is 0, and
return AE_ERROR otherwise.
Tested on a Dell Inspiron 3505 and a Asus Prime B650-Plus.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20240314184538.2933-2-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ACPI EC address space handler currently only supports
reading/writing 8 bit values. Some firmware implementations however
want to access for example 16 bit values, which is perfectly legal
according to the ACPI spec.
Add support for reading/writing such values.
Tested on a Dell Inspiron 3505 and a Asus Prime B650-Plus.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/r/20240314184538.2933-1-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The laptop contains an embedded controller that provides a set of
features:
- Battery and charger monitoring
- USB Type-C DP alt mode HPD monitoring
- Lid status detection
- Small amount of keyboard configuration*
[*] The keyboard is handled by the same EC but it has a dedicated i2c
bus and is already enabled. This port only provides fn key behavior
configuration.
Add the EC to the device tree and describe the relationship between the
EC-managed type-c port and the SoC DisplayPort.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20240315-aspire1-ec-v5-4-f93381deff39@trvn.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acer Aspire 1 is a Snapdragon 7c based laptop. It uses an embedded
controller to perform a set of various functions, such as:
- Battery and charger monitoring;
- Keyboard layout control (i.e. fn_lock settings);
- USB Type-C DP alt mode HPD notifications;
- Laptop lid status.
Unfortunately, while all this functionality is implemented in ACPI, it's
currently not possible to use ACPI to boot Linux on such Qualcomm
devices. To allow Linux to still support the features provided by EC,
this driver reimplments the relevant ACPI parts. This allows us to boot
the laptop with Device Tree and retain all the features.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240315-aspire1-ec-v5-3-f93381deff39@trvn.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Merge series from Joy Zou <joy.zou@nxp.com>:
The patchset supports pmic pca9451a.
For the details, please check the patch commit log.
---
Changes in v5:
- adjust gpio@22 to the front of pmic@25.
Changes in v4:
- modify the comment for uSDHC but not i2c.
Changes in v3:
- modify the dts voltags constraints.
- remove unnecessary changes in driver code.
- modify commit message.
- add tag for dt-bindings.
Changes in v2:
- drop old part support.
Joy Zou (3):
regulator: dt-bindings: pca9450: add pca9451a support
regulator: pca9450: add pca9451a support
arm64: dts: imx93-11x11-evk: add pca9451a support
.../regulator/nxp,pca9450-regulator.yaml | 1 +
.../boot/dts/freescale/imx93-11x11-evk.dts | 111 ++++++++++
drivers/regulator/pca9450-regulator.c | 194 +++++++++++++++++-
include/linux/regulator/pca9450.h | 1 +
4 files changed, 305 insertions(+), 2 deletions(-)
--
2.37.1
Some ARM64 based laptops and computers require vendor/board specific
drivers for their embedded controllers. Even though usually the most
important functionality of those devices is implemented inside ACPI,
unfortunately Linux doesn't currently have great support for ACPI on
platforms like Qualcomm Snapdragon that are used in most ARM64 laptops
today. Instead Linux relies on Device Tree for Qualcomm based devices
and it's significantly easier to reimplement the EC functionality in
a dedicated driver than to make use of ACPI code.
This commit introduces a new platform/arm64 subdirectory to give a
place to such drivers for EC-like devices.
A new MAINTAINERS entry is added for this directory. Patches to files in
this directory will be taken up by the platform-drivers-x86 team (i.e.
Hans de Goede and Ilpo Järvinen) with additional review from Bryan
O'Donoghue to represent ARM64 maintainers.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240315-aspire1-ec-v5-2-f93381deff39@trvn.ru
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sk->sk_rcvbuf in __sock_queue_rcv_skb() and __sk_receive_skb() can be
changed by other threads. Mark this as benign using READ_ONCE().
This patch is aimed at reducing the number of benign races reported by
KCSAN in order to focus future debugging effort on harmful races.
Signed-off-by: linke li <lilinke99@qq.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20240319070038.309683-1-aichao@kylinos.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20240319064243.297320-1-aichao@kylinos.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This changes all *_show attributes in asus-wmi.c to use sysfs_emit()
instead of the older method of writing to the output buffer manually.
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20240319055636.150289-1-aichao@kylinos.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240314063703.315841-1-aichao@kylinos.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
p2sb_get_devfn() always succeeds, make it return void and
remove error checking from its callers.
Reviewed-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240305094500.23778-1-hdegoede@redhat.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240306183538.88777-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the HW restart flow with multi-link is very similar to
the initial association, we do need to reconfigure TLC there.
Remove the check that prevented that.
Fixes: d2d0468f60 ("wifi: iwlwifi: mvm: configure TLC on link activation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.a00adcfe381a.Ic798beccbb7b7d852dc976d539205353588853b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During restart, we haven't added BA sessions, so we also cannot
change them to switch between links when that happens in restart.
Short-circuit the appropriate function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.70ba08540db0.Ic604d384e660c755308a49a79d3f7e78bc27597c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reconfig, we might send keys, but those should be only
sent to already active link stations. Iterate only active ones
to fix that issue.
Fixes: aea99650f7 ("wifi: iwlwifi: mvm: set STA mask for keys in MLO")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.c6818d1c6033.I6357f05c55ef111002ddc169287eb356ca0c1b21@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearly, I put this flag into the wrong place: devices using the
code in mac80211.c only do not support EHT, so this isn't even
relevant. Fix this by moving the code to the right function.
Fixes: 32a5690e9a ("wifi: iwlwifi: mvm: support wider-bandwidth OFDMA")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.0d5fb0e971e4.I3b67c5e0ddcbe6e58143ec0bc4e40dd6dba4f863@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement from OEMs to support new bits in DSM function 7,
which will indicate enablement of 5.9 GHz in Canada.
Add support for this by reading those bits from BIOS and sending it to the
FW. mask unii4 allow bitmap based on LARI_CONFIG_CHANGE_CMD version
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.5c31ccd73119.I0363992efc3607368648d34a7918b2534150a3ca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This comment was added when iwl_mvm_alloc_sta_after_restart configured
the FW with an internal station, but then it was changed by
164a52d45e ("wifi: iwlwifi: mvm: send full STA during HW restart")
to configure the full sta, So there is no reason to "wait for mac80211 to
add the STA" as this is exacly where it happens.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240320232419.d656c2385b06.Icccd0640eb9f1ad72ff74792086435dfc0bee6eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BZ_W is another member of the BZ family.
Just like BZ_U, we also need to override the STEP.
While at it, add a few missing CNVi Chip ID values.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.40c315d51b22.I6b2b2083f8d5b4ec4119aa5b51c21b8428d96060@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During HW restart only one link will be active initially and other links
are only activated again later on. With only a single link EMLSR cannot
be enabled and having it marked enabled confuses the internal state.
Mark EMLSR as disabled in the cleanup iterator, it can be reenabled
later one once this is possible.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.71eb622d6ce3.Ic4d50695b9bb332190dc712473096083aa96074b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>