The bug fixes around GPE races have been done to the EC driver by the
previous commits. This patch increases the revision to 3 to indicate the
behavior differences between the old and the new drivers. The
copyright/authorship notices are also updated.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Timeout in the ec_poll() doesn't refer to the last register access time. It
thus can win the competition against the acpi_ec_gpe_handler() if a
transaction takes longer than 1ms but individual register accesses are less
than 1ms. In some cases, it can make the following silicon bug easier to
be triggered:
GPE EN is not wired to the GPE trigger line, so when GPE STS is already
set when 1 is written to GPE EN, no GPE can be triggered.
This patch adds register access timestamp reference support for ec_poll()
to reduce the number of ec_poll() invocations.
Reported-by: Venkat Raghavulu <venkat.raghavulu@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch switches EC driver into ACPI_GPE_DISPATCH_RAW_HANDLER mode where
the GPE lock is not held for acpi_ec_gpe_handler() and the ACPICA internal
GPE enabling/disabling/clearing operations are bypassed so that further
improvements are possible with the GPE APIs.
There are 2 strong reasons for deploying raw GPE handler mode in the EC
driver:
1. Some hardware logics can control their interrupts via their own
registers, so their interrupts can be disabled/enabled/acknowledged
without using the super IRQ controller provided functions. While there
is no mean (EC commands) for the EC driver to achieve this.
2. During suspending, the EC driver is still working for a while to
complete the platform firmware provided functionailities using ec_poll()
after all GPEs are disabled (see acpi_ec_block_transactions()), which
means the EC driver will drive the EC GPE out of the GPE core's control.
Without deploying the raw GPE handler mode, we can see many races between
the EC driver and the GPE core due to the above restrictions:
1. There is a race condition due to ACPICA internal GPE
disabling/clearing/enabling logics in acpi_ev_gpe_dispatch():
Orignally EC GPE is disabled (EN=0), cleared (STS=0) before invoking a
GPE handler and re-enabled (EN=1) after invoking a GPE handler in
acpi_ev_gpe_dispatch(). When re-enabling appears, GPE may be flagged
(STS=1).
=================================================================
(event pending A)
=================================================================
acpi_ev_gpe_dispatch() ec_poll()
EN=0
STS=0
acpi_ec_gpe_handler()
*****************************************************************
(event handling A)
Lock(EC)
advance_transaction()
EC_SC read
=================================================================
(event pending B)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
*****************************************************************
(event handling B)
Lock(EC)
advance_transaction()
EC_SC read
=================================================================
(event pending C)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
EN=1
This race condition is the root cause of different issues on different
silicon variations.
A. Silicon variation A:
On some platforms, GPE will be triggered due to "writing 1 to EN when
STS=1". This is because both EN and STS lines are wired to the GPE
trigger line.
1. Issue 1:
We can see no-op acpi_ec_gpe_handler() invoked on such platforms.
This is because:
a. event pending B: An event can arrive after ACPICA's GPE
clearing performed in acpi_ev_gpe_dispatch(), this event may
fail to be detected by EC_SC read that is performed before its
arrival;
b. event handling B: The event can be handled in ec_poll() because
EC lock is released after acpi_ec_gpe_handler() invocation;
c. There is no code in ec_poll() to clear STS but the GPE can
still be triggered by the EN=1 write performed in
acpi_ev_finish_gpe(), this leads to a no-op EC GPE handler
invocation;
d. As no-op GPE handler invocations are counted by the EC driver
to trigger the command storming conditions, the wrong no-op
GPE handler invocations thus can easily trigger wrong command
storming conditions.
Note 1:
If we removed GPE disabling/enabling code from
acpi_ev_gpe_dispatch(), we could still see no-op GPE handlers
triggered by the event arriving after the GPE clearing and before
the GPE handling on both silicon variation A and B. This can only
occur if the CPU is very slow (timing slice between STS=0 write
and EC_SC read should be short enough before hardware sets another
GPE indication). Thus this is very rare and is not what we need to
fix.
B. Silicon variation B:
On other platforms, GPE may not be triggered due to "writing 1 to EN
when STS=1". This is because only STS line is wired to the GPE
trigger line.
2. Issue 2:
We can see GPE loss on such platforms. This is because:
a. event pending B vs. event handling A: An event can arrive after
ACPICA's GPE handling performed in acpi_ev_gpe_dispatch(), or
event pending C vs. event handling B: An event can arrive after
Linux's GPE handling performed in ec_poll(),
these events may fail to be detected by EC_SC read that is
performed before their arrival;
b. The GPE cannot be triggered by EN=1 write performed in
acpi_ev_finish_gpe();
c. If no polling mechanism is implemented in the driver for the
pending event (for example, SCI_EVT), this event is lost due to
no GPE being triggered.
Note 2:
On most platforms, there might be another rule that GPE may not be
triggered due to "writing 1 to STS when STS=1 and EN=1".
Then on silicon variation B, an even worse case is if the issue 2
event loss happens, further events may never trigger GPE again on
such platforms due to being blocked by the current STS=1. Unless
someone clears STS, all events have to be polled.
2. There is a race condition due to lacking in GPE status checking in EC
driver:
Originally, GPE status is checked in ACPICA core but not checked in
the GPE handler. Thus since the status checking and handling is not
locked, it can be interrupted by another handling path.
=================================================================
(event pending A)
=================================================================
acpi_ev_gpe_detect() ec_poll()
if (EN==1 && STS==1)
*****************************************************************
(event handling A)
Lock(EC)
advance_transaction()
EC_SC read
EC_SC handled
Unlock(EC)
*****************************************************************
acpi_ev_gpe_dispatch()
EN=0
STS=0
acpi_ec_gpe_handler()
*****************************************************************
(event handling B)
Lock(EC)
advance_transaction()
EC_SC read
Unlock(EC)
*****************************************************************
3. Issue 3:
We can see no-op acpi_ec_gpe_handler() invoked on both silicon
variation A and B. This is because:
a. event pending A: An event can arrive to trigger an EC GPE and
ACPICA checks it and is about to invoke the EC GPE handler;
b. event handling A: The event can be handled in ec_poll() because
EC lock is not held after the GPE status checking;
c. event handling B: Then when the EC GPE handler is invoked, it
becomes a no-op GPE handler invocation.
d. As no-op GPE handler invocations are counted by the EC driver
to trigger the command storming conditions, the wrong no-op
GPE handler invocations thus can easily trigger wrong command
storming conditions.
Note 3:
This no-op GPE handler invocation is rare because the time between
the IRQ arrival and the acpi_ec_gpe_handler() invocation is less than
the timeout value waited in ec_poll(). So most of the no-op GPE
handler invocations are caused by the reason described in issue 1.
3. There is a race condition due to ACPICA internal GPE clearing logic in
acpi_enable_gpe():
During runtime, acpi_enable_gpe() can be invoked by the EC storming
prevention code. When it is invoked, GPE may be flagged (STS=1).
=================================================================
(event pending A)
=================================================================
acpi_ev_gpe_dispatch() acpi_ec_transaction()
EN=0
STS=0
acpi_ec_gpe_handler()
*****************************************************************
(event handling A)
Lock(EC)
advance_transaction()
EC_SC read
EC_SC handled
Unlock(EC)
*****************************************************************
EN=1 ?
Lock(EC)
Unlock(EC)
=================================================================
(event pending B)
=================================================================
acpi_enable_gpe()
STS=0
EN=1
4. Issue 4:
We can see GPE loss on both silicon variation A and B platforms.
This is because:
a. event pending B: An event can arrive right before ACPICA's GPE
clearing performed in acpi_enable_gpe();
b. If the GPE is cleared when GPE is disabled, then EN=1 write in
acpi_enable_gpe() cannot trigger this GPE;
c. If no polling mechanism is implemented in the driver for this
event (for example, SCI_EVT), this event is lost due to no GPE
being triggered.
Note 4:
Currently we don't have this issue, but after we switch the EC
driver into ACPI_GPE_DISPATCH_RAW_HANDLER mode, we need to take care
of handling this because the EN=1 write in acpi_ev_gpe_dispatch()
will be abandoned.
There might be more race issues for the current GPE handler usages. This is
because the EC IRQ's enabling/disabling/checking/clearing/handling
operations should be locked by a single lock that is under the EC driver's
control to achieve the serialization. Which means we need to invoke GPE
APIs with EC driver's lock held and all ACPICA internal GPE operations
related to the GPE handler should be abandoned. Invoking GPE APIs inside of
the EC driver lock and bypassing ACPICA internal GPE operations requires
the ACPI_GPE_DISPATCH_RAW_HANDLER mode where the same lock used by the APIs
are released prior than invoking the handlers. Otherwise, we can see dead
locks due to circular locking dependencies (see Reference below).
This patch then switches the EC driver into the
ACPI_GPE_DISPATCH_RAW_HANDLER mode so that it can perform correct GPE
operations using the GPE APIs:
1. Bypasses EN modifications performed in acpi_ev_gpe_dispatch() by
using acpi_install_gpe_raw_handler() and invoking all GPE APIs with EC
spin lock held. This can fix issue 1 as it makes a non frequent GPE
enabling/disabling environment.
2. Bypasses STS clearing performed in acpi_enable_gpe() by replacing
acpi_enable_gpe()/acpi_disable_gpe() with acpi_set_gpe(). This can fix
issue 4. And this can also help to fix issue 1 as it makes a no sudden
GPE clearing environment when GPE is frequently enabled/disabled.
3. Ensures STS acknowledged before handling by invoking acpi_clear_gpe()
in advance_transaction(). This can finally fix issue 1 even in a
frequent GPE enabling/disabling environment. And this can also finally
fix issue 3 when issue 2 is fixed.
Note 3:
GPE clearing is edge triggered W1C, which means we can clear it right
before handling it. Since all EC GPE indications are handled in
advance_transaction() by previous commits, we can now move GPE clearing
into it to implement the correct GPE clearing.
Note 4:
We can use acpi_set_gpe() which is not shared GPE safer instead of
acpi_enable_gpe()/acpi_disable_gpe() because EC GPE is not shared by
other hardware, which is mentioned in the ACPI specification 5.0, 12.6
Interrupt Model: "OSPM driver treats this as an edge event (the EC SCI
cannot be shared)". So we can stop using shared GPE safer APIs
acpi_enable_gpe()/acpi_disable_gpe() in the EC driver. Otherwise
cleanups need to be made in acpi_ev_enable_gpe() to bypass the GPE
clearing logic before keeping acpi_enable_gpe().
This patch also invokes advance_transaction() when GPE is re-enabled in the
task context which:
1. Ensures EN=1 can trigger GPE by checking and handling EC status register
right after EN=1 writes. This can fix issue 2.
After applying this patch, without frequent GPE enablings considered:
=================================================================
(event pending A)
=================================================================
acpi_ec_gpe_handler() ec_poll()
*****************************************************************
(event handling A)
Lock(EC)
advance_transaction()
if STS==1
STS=0
EC_SC read
=================================================================
(event pending B)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
*****************************************************************
(event handling B)
Lock(EC)
advance_transaction()
if STS==1
STS=0
EC_SC read
=================================================================
(event pending C)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
The event pending for issue 1 (event pending B) can arrive as a next GPE
due to the previous IRQ context STS=0 write. And if it is handled by
ec_poll() (event handling B), as it is also acknowledged by ec_poll(), the
event pending for issue 2 (event pending C) can properly arrive as a next
GPE after the task context STS=0 write. So no GPE will be lost and never
triggered due to GPE clearing performed in the wrong position. And since
all GPE handling is performed after a locked GPE status checking, we can
hardly see no-op GPE handler invocations due to issue 1 and 3. We may still
see no-op GPE handler invocations due to "Note 1", but as it is inevitable,
it needn't be fixed.
After applying this patch, with frequent GPE enablings considered:
=================================================================
(event pending A)
=================================================================
acpi_ec_gpe_handler() acpi_ec_transaction()
*****************************************************************
(event handling A)
Lock(EC)
advance_transaction()
if STS==1
STS=0
EC_SC read
=================================================================
(event pending B)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
*****************************************************************
(event handling B)
Lock(EC)
EN=1
if STS==1
advance_transaction()
if STS==1
STS=0
EC_SC read
=================================================================
(event pending C)
=================================================================
EC_SC handled
Unlock(EC)
*****************************************************************
The event pending for issue 2 can be manually handled by
advance_transaction(). And after the STS=0 write performed in the manual
triggered advance_transaction(), GPE can always arrive. So no GPE will be
lost due to frequent GPE disabling/enabling performed in the driver like
issue 4.
Note 5:
It's ideally when EN=1 write occurred, an IRQ thread should be woken up to
handle the GPE when the GPE was raised. But this requires the IRQ thread to
contain the poller code for all EC GPE indications, while currently some of
the indications are handled in the user tasks. It then is very hard for the
code to determine whether a user task should be invoked or the poller work
item should be scheduled. So we have to invoke advance_transaction()
directly now and it leaves us such a restriction for the GPE re-enabling:
it must be performed in the task context to avoid starving the GPEs.
As a conclusion: we can see the EC GPE is always handled in serial after
deploying the raw GPE handler mode:
Lock(EC)
if (STS==1)
STS=0
EC_SC read
EC_SC handled
Unlock(EC)
The EC driver specific lock is responsible to make the EC GPE handling
processes serialized so that EC can handle its GPE from both IRQ and task
contexts and the next IRQ can be ensured to arrive after this process.
Note 6:
We have many EC_FLAGS_MSI qurik users in the current driver. They all seem
to be suffering from unexpected GPE triggering source lost. And they are
false root caused to a timing issue. Since EC communication protocol has
already flow control defined, timing shouldn't be the root cause, while
this fix might be fixing the root cause of the old bugs.
Link: https://lkml.org/lkml/2014/11/4/974
Link: https://lkml.org/lkml/2014/11/18/316
Link: https://www.spinics.net/lists/linux-acpi/msg54340.html
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit da9a83e1a845f2d7332bdbc0632466b2595e5424
For acpi_set_gpe()/acpi_enable_gpe(), our target is to purify them to be APIs
that can be used for various GPE handling models, so we need them to be
pure GPE enabling APIs. GPE enabling/disabling has 2 use cases:
1. Driver may permanently enable/disable GPEs according to the usage
counts.
1. When upper layers (the users of the driver) submit requests to the
driver, it means they care about the underlying hardware. GPE need
to be enabled for the first request submission and disabled for the
last request completion.
2. When the GPE is shared between 2+ silicon logics. GPE need to be
enabled for either silicon logic's driver and disabled when all of
the drivers are not started.
For these cases, acpi_enable_gpe()/acpi_disable_gpe() should be used. When
the usage count is increased from 0 to 1, the GPE is enabled and it is
disabled when the usage count is decrased from 1 to 0.
2. Driver may temporarily disables the GPE to enter an GPE polling mode and
wants to re-enable it later.
1. Prevent GPE storming: when a driver cannot fully solve the condition
that triggered the GPE in the GPE context, in order not to trigger
GPE storm, driver has to disable GPE to switch into the polling mode
and re-enables it in the non interrupt context after the storming
condition is cleared.
2. Meet throughput requirement: some IO drivers need to poll hardware
again and again until nothing indicated instead of just handling once
for one interruption, this need to be done in the polling mode or the
IO flood may prevent the GPE handler from returning.
3. Meet realtime requirement: in order not to block CPU to handle higher
realtime prioritized GPEs, lower priority GPEs can be handled in the
polling mode.
For these cases, acpi_set_gpe() should be used to switch to/from the
polling mode.
This patch adds unconditional GPE enabling support into acpi_set_gpe() so
that this API can be used by the drivers to switch back from the GPE
polling mode unconditionally.
Originally this function includes GPE clearing logic in it.
First, the GPE clearing is typically used in the GPE handling code to:
1. Acknowledge the GPE when we know there is an edge triggered GPE raised
and is about to handle it, otherwise the unexpected clearing may lead to
a GPE loss;
2. Issue actions after we have handled a level triggered GPE, otherwise
the unexpected clearing may trigger unwanted OSPM actions to the
hardware (for example, clocking in out-dated write FIFO data).
Thus the GPE clearing is not suitable to be used in the GPE enabling APIs.
Second, the combination of acknowledging and enabling may also not be
expected by the hardware drivers. For GPE clearing, we have a seperate API
acpi_clear_gpe(). There are cases drivers do want the 2 operations to be
split. So splitting these 2 operations could facilitates drivers the
maximum possibilities to achieve success. For a combined one, we already
have acpi_finish_gpe() ready to be invoked.
Given the fact that drivers should complete all outstanding requests before
putting themselves into the sleep states, as this API is executed for
outstanding requests, it should also have nothing to do with the
"RUN"/"WAKE" distinguishing. That's why the acpi_set_gpe(ACPI_GPE_ENABLE)
should not be implemented by acpi_hw_low_set_gpe(ACPI_GPE_CONDITIONAL_ENABLE).
This patch thus converts acpi_set_gpe(ACPI_GPE_ENABLE) into
acpi_hw_low_set_gpe(ACPI_GPE_ENABLE) to achieve a seperate GPE enabling API.
Drivers then are encouraged to use this API when they need to switch
to/from the GPE polling mode.
Note that the acpi_set_gpe()/acpi_finish_gpe() should be first introduced to
Linux using a divergence reduction patch before sending a linuxized version
of this patch. Lv Zheng.
Link: da9a83e1
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This can help to reduce source code differences between Linux and ACPICA
upstream. Further driver cleanups also require these APIs to eliminate GPE
storms.
1. acpi_set_gpe(): An API that driver should invoke in the case it wants
to disable/enable IRQ without honoring the reference
count implemented in the acpi_disable_gpe() and
acpi_enable_gpe(). Note that this API should only be
invoked inside a acpi_enable_gpe()/acpi_disable_gpe()
pair.
2. acpi_finish_gpe(): Drivers returned ACPI_REENABLE_GPE unset from the
GPE handler should use this API instead of
invoking acpi_set_gpe()/acpi_enable_gpe() to
re-enable the GPE.
The GPE APIs can be invoked inside of a GPE handler or in the task context
with a driver provided lock held. This driver provided lock is safe to be
held in the GPE handler by the driver.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 199cad16530a45aea2bec98e528866e20c5927e1
Since whether the GPE should be disabled/enabled/cleared should only be
determined by the GPE driver's state machine:
1. GPE should be disabled if the driver wants to switch to the GPE polling
mode when a GPE storm condition is indicated and should be enabled if
the driver wants to switch back to the GPE interrupt mode when all of
the storm conditions are cleared. The conditions should be protected by
the driver's specific lock.
2. GPE should be enabled if the driver has accepted more than one request
and should be disabled if the driver has completed all of the requests.
The request count should be protected by the driver's specific lock.
3. GPE should be cleared either when the driver is about to handle an edge
triggered GPE or when the driver has completed to handle a level
triggered GPE. The handling code should be protected by the driver's
specific lock.
Thus the GPE enabling/disabling/clearing operations are likely to be
performed with the driver's specific lock held while we currently cannot do
this. This is because:
1. We have the acpi_gbl_gpe_lock held before invoking the GPE driver's
handler. Driver's specific lock is likely to be held inside of the
handler, thus we can see some dead lock issues due to the reversed
locking order or recursive locking. In order to solve such dead lock
issues, we need to unlock the acpi_gbl_gpe_lock before invoking the
handler. BZ 1100.
2. Since GPE disabling/enabling/clearing should be determined by the GPE
driver's state machine, we shouldn't perform such operations inside of
ACPICA for a GPE handler to mess up the driver's state machine. BZ 1101.
Originally this patch includes a logic to flush GPE handlers, it is dropped
due to the following reasons:
1. This is a different issue;
2. Linux OSL has fixed this by flushing SCI in acpi_os_wait_events_complete().
We will pick up this topic when the Linux OSL fix turns out to be not
sufficient.
Note that currently the internal operations and the acpi_gbl_gpe_lock are
also used by ACPI_GPE_DISPATCH_METHOD and ACPI_GPE_DISPATCH_NOTIFY. In
order not to introduce regressions, we add one
ACPI_GPE_DISPATCH_RAW_HANDLER type to be distiguished from
ACPI_GPE_DISPATCH_HANDLER. For which the acpi_gbl_gpe_lock is unlocked before
invoking the GPE handler and the internal enabling/disabling operations are
bypassed to allow drivers to perform them at a proper position using the
GPE APIs and ACPI_GPE_DISPATCH_RAW_HANDLER users should invoke acpi_set_gpe()
instead of acpi_enable_gpe()/acpi_disable_gpe() to bypass the internal GPE
clearing code in acpi_enable_gpe(). Lv Zheng.
Known issues:
1. Edge-triggered GPE lost for frequent enablings
On some buggy silicon platforms, GPE enable line may not be directly
wired to the GPE trigger line. In that case, when GPE enabling is
frequently performed for edge-triggered GPEs, GPE status may stay set
without being triggered.
This patch may maginify this problem as it allows GPE enabling to be
parallel performed during the process the GPEs are handled.
This is an existing issue, because:
1. For task context:
Current ACPI_GPE_DISPATCH_METHOD practices have proven that this
isn't a real issue - we can re-enable edge-triggered GPE in a work
queue where the GPE status bit might already be set.
2. For IRQ context:
This can even happen when the GPE enabling occurs before returning
from the GPE handler and after unlocking the GPE lock.
Thus currently no code is included to protect this.
Link: 199cad16
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8990e73ab2aa15d6a0068b860ab54feff25bee36
Link: 8990e73a
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 490ec7f7839bf7ee5e8710a34d1d1a78d54a49b6
In function acpi_hw_low_set_gpe(), cast enable_mask to u8 before
storing. The mask was read from a 32 bit register but is an 8 bit
value. Fixes Visual Studio compiler warning.
Link: 490ec7f7
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7926d5ca9452c87f866938dcea8f12e1efb58f89
There is an issue in acpi_install_gpe_handler() and acpi_remove_gpe_handler().
The code to obtain the GPE dispatcher type from the Handler->original_flags
is wrong:
if (((Handler->original_flags & ACPI_GPE_DISPATCH_METHOD) ||
(Handler->original_flags & ACPI_GPE_DISPATCH_NOTIFY)) &&
ACPI_GPE_DISPATCH_NOTIFY is 0x03 and ACPI_GPE_DISPATCH_METHOD is 0x02, thus
this statement is TRUE for the following dispatcher types:
0x01 (ACPI_GPE_DISPATCH_HANDLER): not expected
0x02 (ACPI_GPE_DISPATCH_METHOD): expected
0x03 (ACPI_GPE_DISPATCH_NOTIFY): expected
There is no functional issue due to this because Handler->original_flags is
only set in acpi_install_gpe_handler(), and an earlier checker has excluded
the ACPI_GPE_DISPATCH_HANDLER:
if ((gpe_event_info->Flags & ACPI_GPE_DISPATCH_MASK) ==
ACPI_GPE_DISPATCH_HANDLER)
{
Status = AE_ALREADY_EXISTS;
goto free_and_exit;
}
...
Handler->original_flags = (u8) (gpe_event_info->Flags &
(ACPI_GPE_XRUPT_TYPE_MASK | ACPI_GPE_DISPATCH_MASK));
We need to clean this up before modifying the GPE dispatcher type values.
In order to prevent such issue from happening in the future, this patch
introduces ACPI_GPE_DISPATCH_TYPE() macro to be used to obtain the GPE
dispatcher types. Lv Zheng.
Link: 7926d5ca
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 04f25acdd4f655ae33f83de789bb5f4b7790171c
This patch follows acpi_ev_fixed_event_detect(), which invokes
acpi_gbl_global_event_handler instead of invoking it in
acpi_ev_fixed_event_dispatch(), moves acpi_gbl_global_event_handler from
acpi_ev_gpe_dispatch() to acpi_ev_gpe_detect(). This makes further cleanups
around acpi_ev_gpe_dispatch() simpler. Lv Zheng.
Link: 04f25acd
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b2b18bb38045404e253f10787b8a4ae6e94cdee6
This patch prevents acpi_remove_gpe_handler() from leaking the stale
gpe_event_info->Dispatch.Handler to the caller to avoid possible NULL pointer
references. Lv Zheng.
Link: b2b18bb3
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8e21180050270897499652e922c6a41b8eb388b6
Recent changes to acpi_ev_asynch_execute_gpe_method left Status
variable uninitialized before use. Initialize to AE_OK.
Link: 8e211800
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8823b44ff53859ab24ecfcfd3fba8cc56b17d223
Currently we rely on the logic that GPE blocks will never be deleted,
otherwise we can be broken by the race between acpi_ev_create_gpe_block(),
acpi_ev_delete_gpe_block() and acpi_ev_gpe_detect().
On the other hand, if we want to protect GPE block creation/deletion, we
need to use a different synchronization facility to protect the period
between acpi_ev_gpe_dispatch() and acpi_ev_asynch_enable_gpe(). Which leaves us
no choice but abandoning the ACPI_MTX_EVENTS used during this period.
This patch removes ACPI_MTX_EVENTS used during this period and the
acpi_ev_valid_gpe_event() to reflect current restriction. Lv Zheng.
Link: 8823b44f
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ca10324788bc9bdaf47fa9e51145129c1299144d
This patch deletes a sanity check from acpi_ev_enable_gpe().
This kind of check is already done in
acpi_enable_gpe()/acpi_remove_gpe_handler()/acpi_update_all_gpes() before invoking
acpi_ev_enable_gpe():
1. acpi_enable_gpe(): same check (skip if DISPATCH_NONE) is now implemented.
2. acpi_remove_gpe_handler(): a more strict check (skip if !DISPATCH_HANDLER)
is implemented.
3. acpi_update_all_gpes(): a more strict check (skip if DISPATCH_NONE ||
DISPATCH_HANDLER || CAN_WAKE)
4. acpi_set_gpe(): since it is invoked by the OSPM driver where the GPE
handler is known to be available, such check isn't needed.
So we can simply remove this duplicated check from acpi_ev_enable_gpe().
Lv Zheng.
Link: ca103247
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a back port result of the Linux commit:
Commit c50f13c672
Subject: ACPICA: Save current masks of enabled GPEs after enable register writes
Besides of the indent divergences, only a missing prototype added due to
the ACPICA internal coding style.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA has implemented acpi_unload_parent_table() which can exactly replace
the acpi_get_id()/acpi_unload_table_id() implemented in Linux kernel. The
acpi_unload_parent_table() has been unit tested in ACPICA simulation
environment.
This patch can also help to reduce the source code differences between
Linux and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The QR_EC related code pieces have redundants, this patch merges them into
acpi_ec_query() which invokes acpi_ec_transaction() where EC mutex and the
global lock are already held. After doing so, query handler traversal still
need to be locked by EC mutex after invoking acpi_ec_transaction().
Note that EC event handling is sequential. We fetch one event from firmware
event queue and process it until 0x00 or error returned. So we don't need
to hold mutex for whole acpi_ec_clear() process to determine whether we
should continue to drain. And for the same reason, we don't need to hold
mutex for the whole procedure from the QR_EC transaction to the query
handler traversal.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes 2 issues related to the draining behavior. But it doesn't
implement the draining support, it only cleans up code so that further
draining support is possible.
The draining behavior is expected by some platforms (for example, Samsung)
where SCI_EVT is set only once for a set of events and might be cleared for
the very first QR_EC command issued after SCI_EVT is set. EC firmware on
such platforms will return 0x00 to indicate "no outstanding event". Thus
after seeing an SCI_EVT indication, EC driver need to fetch events until
0x00 returned (see acpi_ec_clear()).
Issue 1 - acpi_ec_submit_query():
It's reported on Samsung laptops that SCI_EVT isn't checked when the
transactions are advanced in ec_poll(), which leads to SCI_EVT triggering
source lost:
If no EC GPE IRQs are arrived after that, EC driver cannot detect this
event and handle it.
See comment 244/247 for kernel bugzilla 44161.
This patch fixes this issue by moving SCI_EVT checks into
advance_transaction(). So that SCI_EVT is checked each time we are going to
handle the EC firmware indications. And this check will happen for both IRQ
context and task context.
Since after doing that, SCI_EVT is also checked after completing a
transaction, ec_check_sci() and ec_check_sci_sync() can be removed.
Issue 2 - acpi_ec_complete_query():
We expect to clear EC_FLAGS_QUERY_PENDING to allow queuing another draining
QR_EC after writing a QR_EC command and before reading the event. After
reading the event, SCI_EVT might be cleared by the firmware, thus it may
not be possible to queue such a draining QR_EC at that time.
But putting the EC_FLAGS_QUERY_PENDING clearing code after
start_transaction() is wrong as there are chances that after
start_transaction(), QR_EC can fail to be sent. If this happens,
EC_FLAG_QUERY_PENDING will be cleared earlier. As a consequence, the
draining QR_EC will also be queued earlier than expected.
This patch also moves this code into advance_transaction() where QR_EC is
just sent (ACPI_EC_COMMAND_POLL flagged) to fix this issue.
Notes:
1. After introducing the 2 SCI_EVT related handlings into
advance_transaction(), a next QR_EC can be queued right after writing
the current QR_EC command and before reading the event. But this still
hasn't implemented the draining behavior as the draining support
requires:
If a previous returned event value isn't 0x00, a draining QR_EC need
to be issued even when SCI_EVT isn't set.
2. In this patch, acpi_os_execute() is also converted into a seperate work
item to avoid invoking kmalloc() in the atomic context. We can do this
because of the previous global lock fix.
3. Originally, EC_FLAGS_EVENT_PENDING is also used to avoid queuing up
multiple work items (created by acpi_os_execute()), this can be covered
by only using a single work item. But this patch still keeps this flag
as there are different usages in the driver initialization steps relying
on this flag.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Reported-by: Kieran Clancy <clancy.kieran@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently QR_EC is queued up on CPU 0 to be safe with SMM because there is
no global lock held for acpi_ec_gpe_query(). As we are about to move QR_EC
to a non CPU 0 bound work queue to avoid invoking kmalloc() in
advance_transaction(), we have to acquire global lock for the new QR_EC
work item to avoid regressions.
Known issue:
1. Global lock for acpi_ec_clear().
This is an existing issue that acpi_ec_clear() which invokes
acpi_ec_sync_query() also suffers from the same issue. But this patch's
target is only the code to invoke acpi_ec_sync_query() in a CPU 0 bound
work queue item, and the acpi_ec_clear() can be automatically fixed by
further patch that merges the redundant code, so it is left unchanged.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The returning value of acpi_os_execute() is erroneously handled as errno.
This patch corrects it by returning EBUSY to indicate the work queue item
creation failure.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds reference counting for query handlers in order to eliminate
kmalloc()/kfree() usage.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves transaction wakeup code into advance_transaction().
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_tb_delete_namespace_by_owner() expects ACPI_MTX_INTERPRETER to be
taken. This fixes the following issue:
ACPI Error: Mutex [0x0] is not acquired, cannot release (20141107/utmutex-322)
Call Trace:
[<ffffffff81b0bd28>] dump_stack+0x4f/0x7b
[<ffffffff81546bfc>] acpi_ut_release_mutex+0x47/0x67
[<ffffffff81542cf1>] acpi_tb_delete_namespace_by_owner+0x57/0x8d
[<ffffffff81543ef1>] acpi_unload_table_id+0x3a/0x5e
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various bugs
around clocks, reg ranges, etc. There's also a few defconfig updates
(which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but the nothing
in here seems particularly risky.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lJPi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
dereference fix in the framework core code. The driver fixes vary from
fixing section mismatch warnings to preventing machines from hanging
(and preventing developers from crying).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B+t3
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"Small number of fixes for clock drivers and a single null pointer
dereference fix in the framework core code.
The driver fixes vary from fixing section mismatch warnings to
preventing machines from hanging (and preventing developers from
crying)"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: fix possible null pointer dereference
Revert "clk: ppc-corenet: Fix Section mismatch warning"
clk: rockchip: fix deadlock possibility in cpuclk
clk: berlin: bg2q: remove non-exist "smemc" gate clock
clk: at91: keep slow clk enabled to prevent system hang
clk: rockchip: fix rk3288 cpuclk core dividers
clk: rockchip: fix rk3066 pll lock bit location
clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri
clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host
This is one fix for a Multiqueue sleeping in invalid context problem and a
MAINTAINER file update for Qlogic.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUusiiAAoJEDeqqVYsXL0MyrgH/iOi8ERmP0TJKZVEPeYacas6
YZeUw0ZsckpqgaE/PoRdkgGx6Slz4Nm2x+Dz1VEr1SWtGNIKLnAgHVP1S/Ee/4ws
0vVYd4VZ4OzT8FkjHRHeeeBj9EWSR0Zeh4eZu+eIilo9FOhJTHzy8R6vQxS9b3Hu
GzuVm2MaQHmYaAVVMnbitwj41pczLzDwDzmTBqcoh8ak8ynBiFBFgWxg+ZDyJtcZ
KRusp/nKJGuxoehHmgLI+Vor2jCrVpagyIbAqkHtn9OLZEtmaTkGrR42qlIedxZb
cUNDVysmrI8lRhkwiVD7+mT4A377MMlfjO0qFCUc+bkz1xTyyP2ABLT8IhmpO4w=
=5EBM
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is one fix for a Multiqueue sleeping in invalid context problem
and a MAINTAINER file update for Qlogic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ->queue_rq can't sleep
MAINTAINERS: Update maintainer list for qla4xxx
The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This reverts commit da788acb28.
That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.
CPU0 CPU1
---- ----
lock(clk_lock);
local_irq_disable();
lock(&(&i2c->lock)->rlock);
lock(clk_lock);
<Interrupt>
lock(&(&i2c->lock)->rlock);
*** DEADLOCK ***
The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]
Pull dmaengine fixes from Vinod Koul:
"Two patches, the first by Andy to fix dw dmac runtime pm and second
one by me to fix the dmaengine headers in MAINTAINERS"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: balance PM runtime calls
MAINTAINERS: dmaengine: fix the header file for dmaengine
Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.
I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.
[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimus
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are 3 small driver fixes for reported issues for 3.19-rc5. All of
these have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5VzYACgkQMUfUDdst+ylv5gCfT8krEtuWXM1NMZwIuftf4Whb
z8cAn23whaxGED7AyBRVXxMohYF8Vxq9
=yMIV
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are three small driver fixes for reported issues for 3.19-rc5.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
mei: add ABI documentation for fw_status exported through sysfs
mei: clean reset bit before reset
Here are some tty and serial driver fixes for 3.19-rc5 that resolve some
reported issues, and add a new device id to the 8250 serial port driver.
All have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5WKAACgkQMUfUDdst+yk6GwCgje1loYJvK4f8hnTNHvStT9Im
5NEAn1NBKcnW/0mpadUFyUO6PAJ6dSTy
=wDV8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 3.19-rc5 that resolve
some reported issues, and add a new device id to the 8250 serial port
driver.
All have been in linux-next with no reported problems"
* tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Add the support for Exynos5433 SoC
Revert "tty: Fix pty master poll() after slave closes v2"
tty: Prevent hw state corruption in exclusive mode reopen
tty: Add support for the WCH384 4S multi-IO card
serial: fix parisc boot hang
Here are 6 staging driver fixes for 3.19-rc5.
They fix some reported issues with some IIO drivers, as well as some
issues with the vt6655 wireless driver.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5WDwACgkQMUfUDdst+ymQlwCeIm6FX0auD5SOlqqGBPvIR6kr
8AoAoISQNfaBmroFcgfi7adGyEKsgkv7
=Ig20
-----END PGP SIGNATURE-----
Merge tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are 6 staging driver fixes for 3.19-rc5.
They fix some reported issues with some IIO drivers, as well as some
issues with the vt6655 wireless driver.
All have been in linux-next for a while"
* tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: fix sparse warning: argument type
staging: vt6655: Fix loss of distant/weak access points on channel change.
staging: vt6655: vnt_tx_packet Fix corrupted tx packets.
staging: vt6655: fix sparse warnings: incorrect argument type
iio: iio: Fix iio_channel_read return if channel havn't info
iio: ad799x: Fix ad7991/ad7995/ad7999 config setup
Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlS5WTQACgkQMUfUDdst+ykYQgCffWxrhuQKYJLYVYmIoDS8lL/c
1v4AoIowfSV08l22puWQpAOih/tg0WGI
=mfZA
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems"
* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
usb: dwc3: gadget: Stop TRB preparation after limit is reached
usb: dwc3: gadget: Fix TRB preparation during SG
usb: phy: mv-usb: fix usb_phy build errors
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
usb: serial: silence all non-critical read errors
USB: console: fix potential use after free
USB: console: fix uninitialised ldisc semaphore
usb: gadget: udc: atmel: fix possible oops when unloading module
usb: gadget: gadgetfs: fix an oops in ep_write()
usb: phy: Fix deferred probing
OHCI: add a quirk for ULi M5237 blocking on reset
uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
uas: Do not blacklist ASM1153 disk enclosures
usb: gadget: udc: avoid dereference before NULL check in ep_queue
usb: host: ehci-tegra: request deferred probe when failing to get phy
uas: disable UAS on Apricorn SATA dongles
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
USB: EHCI: adjust error return code
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9ZIN
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
"A few powerpc fixes"
* tag 'powerpc-3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: Work around gcc bug in current_thread_info()
cxl: Fix issues when unmapping contexts
powernv: Fix OPAL tracepoint code
Pull thermal fixes from Zhang Rui:
"Specifics:
- bogus type qualifier fix in OF thermal code.
- Minor fixes on imx and rcar thermal drivers.
- Update TI SoC thermal maintainer entry.
- Updated documentation of OF cpufreq cooling register"
* 'thermal-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar: Spelling/grammar: s/drier use .../driver uses ...s/
thermal: rcar: change type of ctemp in rcar_thermal_update_temp()
thermal: rcar: fix ENR register value
Documentation: thermal: document of_cpufreq_cooling_register()
Thermal: imx: add clk disable/enable for suspend/resume
MAINTAINERS: update ti-soc-thermal status
MAINTAINERS: Add linux-omap to list of reviewers for TI Thermal
thermal: of: Remove bogus type qualifier for of_thermal_get_trip_points()
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iLKs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=umHr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc5
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull networking fixes from David Miller:
1) Don't use uninitialized data in IPVS, from Dan Carpenter.
2) conntrack race fixes from Pablo Neira Ayuso.
3) Fix TX hangs with i40e, from Jesse Brandeburg.
4) Fix budget return from poll calls in dnet and alx, from Eric
Dumazet.
5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
Jaeger.
6) Fix bug introduced by conversion to list_head in TIPC retransmit
code, from Jon Paul Maloy.
7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
Khoroshilov.
8) Fix bridge build with INET disabled, from Arnd Bergmann.
9) Fix netlink array overrun for PROBE attributes in openvswitch, from
Thomas Graf.
10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
Prashant Sreedharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
tg3: Release tp->lock before invoking synchronize_irq()
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
openvswitch: packet messages need their own probe attribtue
i40e: adds FCoE configure option
cxgb4vf: Fix queue allocation for 40G adapter
netdevice: Add missing parentheses in macro
bridge: only provide proxy ARP when CONFIG_INET is enabled
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
net: fec: fix MDIO bus assignement for dual fec SoC's
xen-netfront: use different locks for Rx and Tx stats
drivers: net: cpsw: fix multicast flush in dual emac mode
cxgb4vf: Initialize mdio_addr before using it
net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
MAINTAINERS: add me as ibmveth maintainer
tipc: fix bug in broadcast retransmit code
update ip-sysctl.txt documentation (v2)
net/at91_ether: prepare and unprepare clock
...
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
"Two small performance tweaks, the plumbing for the execveat system
call and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix user space PER events
s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
s390/bpf: Fix ALU_NEG (A = -A)
s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
s390/timex: fix get_tod_clock_ext() inline assembly
s390: wire up execveat syscall
s390/kernel: use stnsm 255 instead of stosm 0
s390/vtime: Get rid of redundant WARN_ON
s390/zcrypt: kernel oops at insmod of the z90crypt device driver