Since the WDT is what's used to drive restart and power off, it makes
more sense to keep it there, where the regs are already mapped and
definitions for them provided. Note that this means you may need to
add CONFIG_BCM2835_WDT to retain functionality of your kernel.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the default function that gets called if the hook is NULL.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The only thing we were using this 16MB mapping of IO peripherals for
was the uart's early debug mapping. If we just drop the map_io hook,
the kernel will call debug_ll_io_init() for us, which maps the single
page needed for the device.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There exists a tiny MMU, configurable only by the VC (running the
closed firmware), which maps from the ARM's physical addresses to bus
addresses. These bus addresses determine the caching behavior in the
VC's L1/L2 (note: separate from the ARM's L1/L2) according to the top
2 bits. The bits in the bus address mean:
From the VideoCore processor:
0x0... L1 and L2 cache allocating and coherent
0x4... L1 non-allocating, but coherent. L2 allocating and coherent
0x8... L1 non-allocating, but coherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
From the GPU peripherals (note: all peripherals bypass the L1
cache. The ARM will see this view once through the VC MMU):
0x0... Do not use
0x4... L1 non-allocating, and incoherent. L2 allocating and coherent.
0x8... L1 non-allocating, and incoherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
The 2835 firmware always configures the MMU to turn ARM physical
addresses with 0x0 top bits to 0x4, meaning present in L2 but
incoherent with L1. However, any bus addresses we were generating in
the kernel to be passed to a device had 0x0 bits. That would be a
reserved (possibly totally incoherent) value if sent to a GPU
peripheral like USB, or L1 allocating if sent to the VC (like a
firmware property request). By setting dma-ranges, all of the devices
below it get a dev->dma_pfn_offset, so that dma_alloc_coherent() and
friends return addresses with 0x4 bits and avoid cache incoherency.
This matches the behavior in the downstream 2708 kernel (see
BUS_OFFSET in arch/arm/mach-bcm2708/include/mach/memory.h).
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Device tree node names should contain the node's reg property address value.
The i2c0 node was apparently forgotten in commit 25b2f1bd0b (ARM: bcm2835:
node name unit address cleanup).
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This new header file defines pincontrol constants to use
from bcm2835 DTS files for pincontrol properties option.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds root compatible properties for the following boards:
- Raspberry Pi Model A
- Raspberry Pi Model A+
- Raspberry Pi Model B
- Raspberry Pi Model B (no P5)
- Raspberry Pi Model B rev2
- Raspberry Pi Model B+
- Raspberry Pi Compute Module
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the prefix is already in use, we need to add it in the
vendor list.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes hci_remote_name_evt dose not resolve name during
discovery status is RESOLVING. Before simultaneous dual mode scan enabled,
hci_check_pending_name will set discovery status to STOPPED eventually.
Signed-off-by: Wesley Kuo <wesley.kuo@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When removing an opaque directory we can't just call rmdir() to check for
emptiness, because the directory will need to be replaced with a whiteout.
The replacement is done with RENAME_EXCHANGE, which doesn't check
emptiness.
Solution is just to check emptiness by reading the directory. In the
future we could add a new rename flag to check for emptiness even for
RENAME_EXCHANGE to optimize this case.
Reported-by: Vincent Batts <vbatts@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Jordi Pujol Palomer <jordipujolp@gmail.com>
Fixes: 263b4a0fee ("ovl: dont replace opaque dir")
Cc: <stable@vger.kernel.org> # v4.0+
Recent toolchains force the TOC to be 256 byte aligned. We need
to enforce this alignment in our linker script, otherwise pointers
to our TOC variables (__toc_start, __prom_init_toc_start) could
be incorrect.
If they are bad, we die a few hundred instructions into boot.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull it up into the header and kill duplicate versions.
Separately, both macros are identical:
35948b2bd3431aee7149e85cfe4becbc /tmp/a
35948b2bd3431aee7149e85cfe4becbc /tmp/b
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1431538944-27724-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter ingress support (v4)
This is the v4 round of patches to add the Netfilter ingress hook, it basically
comes in two steps:
1) Add the CONFIG_NET_INGRESS switch to wrap the ingress static key around it.
The idea is to use the same global static key to avoid adding more code to
the hot path.
2) Add the Netfilter ingress hook after the tc ingress hook, under the global
ingress_needed static key. As I said, the netfilter ingress hook also has
its own static key, that is nested under the global static key. Please, see
patch 5/5 for performance numbers and more information.
I originally started this next round, as it was suggested, exploring the
independent static key for netfilter ingress just after tc ingress, but the
results that I gathered from that patch are not good for non-users:
Result: OK: 6425927(c6425843+d83) usec, 100000000 (60byte,0frags)
15561955pps 7469Mb/sec (7469738400bps) errors: 100000000
this roughly means 500Kpps less performance wrt. the base numbers, so that's
the reason why I discarded that approach and I focused on this.
The idea of this patchset is to open the window to nf_tables, which comes with
features that will work out-of-the-box (once the boiler plate code to support
the 'netdev' table family is in place), to avoid repeating myself [1], the most
relevant features are:
1) Multi-dimensional key dictionary lookups.
2) Arbitrary stateful flow tables.
3) Transactions and good support for dynamic updates.
But there are also interest aspects to consider from userspace, such as the
ability to support new layer 2 protocols without kernel updates, a well-defined
netlink interface, userspace libraries and utilities for third party
applications, among others.
I hope we can be happy with this approach.
Please, apply. Thanks.
[1] http://marc.info/?l=netfilter-devel&m=143033337020328&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Netfilter ingress hook just after the existing tc ingress
hook, that seems to be the consensus solution for this.
Note that the Netfilter hook resides under the global static key that enables
ingress filtering. Nonetheless, Netfilter still also has its own static key for
minimal impact on the existing handle_ing().
* Without this patch:
Result: OK: 6216490(c6216338+d152) usec, 100000000 (60byte,0frags)
16086246pps 7721Mb/sec (7721398080bps) errors: 100000000
42.46% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
25.92% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
7.81% kpktgend_0 [pktgen] [k] pktgen_thread_worker
5.62% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.70% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
2.34% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
1.44% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* With this patch:
Result: OK: 6214833(c6214731+d101) usec, 100000000 (60byte,0frags)
16090536pps 7723Mb/sec (7723457280bps) errors: 100000000
41.23% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
26.57% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
7.72% kpktgend_0 [pktgen] [k] pktgen_thread_worker
5.55% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.78% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
2.06% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
1.43% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* Without this patch + tc ingress:
tc filter add dev eth4 parent ffff: protocol ip prio 1 \
u32 match ip dst 4.3.2.1/32
Result: OK: 9269001(c9268821+d179) usec, 100000000 (60byte,0frags)
10788648pps 5178Mb/sec (5178551040bps) errors: 100000000
40.99% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
17.50% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
11.77% kpktgend_0 [cls_u32] [k] u32_classify
5.62% kpktgend_0 [kernel.kallsyms] [k] tc_classify_compat
5.18% kpktgend_0 [pktgen] [k] pktgen_thread_worker
3.23% kpktgend_0 [kernel.kallsyms] [k] tc_classify
2.97% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
1.83% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
1.50% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
0.99% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* With this patch + tc ingress:
tc filter add dev eth4 parent ffff: protocol ip prio 1 \
u32 match ip dst 4.3.2.1/32
Result: OK: 9308218(c9308091+d126) usec, 100000000 (60byte,0frags)
10743194pps 5156Mb/sec (5156733120bps) errors: 100000000
42.01% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
17.78% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
11.70% kpktgend_0 [cls_u32] [k] u32_classify
5.46% kpktgend_0 [kernel.kallsyms] [k] tc_classify_compat
5.16% kpktgend_0 [pktgen] [k] pktgen_thread_worker
2.98% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.84% kpktgend_0 [kernel.kallsyms] [k] tc_classify
1.96% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
1.57% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
Note that the results are very similar before and after.
I can see gcc gets the code under the ingress static key out of the hot path.
Then, on that cold branch, it generates the code to accomodate the netfilter
ingress static key. My explanation for this is that this reduces the pressure
on the instruction cache for non-users as the new code is out of the hot path,
and it comes with minimal impact for tc ingress users.
Using gcc version 4.8.4 on:
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 8
[...]
L1d cache: 16K
L1i cache: 64K
L2 cache: 2048K
L3 cache: 8192K
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new config switch enables the ingress filtering infrastructure that is
controlled through the ingress_needed static key. This prepares the
introduction of the Netfilter ingress hook that resides under this unique
static key.
Note that CONFIG_SCH_INGRESS automatically selects this, that should be no
problem since this also depends on CONFIG_NET_CLS_ACT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to have netfilter ingress per-device hook list.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan notifier handler will try to update all vlans
for a device when that device comes up. A problem occurs,
however, when the vlan device was set to promiscuous, but not
by the user (ex: a bridge). In that case, dev->gflags are
not updated. What results is that the lower device ends
up with an extra promiscuity count. Here are the
backtraces that prove this:
[62852.052179] [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.052186] [<ffffffff8160bcbb>] ? _raw_spin_unlock_bh+0x1b/0x40
[62852.052188] [<ffffffff814fe4be>] ? dev_set_rx_mode+0x2e/0x40
[62852.052190] [<ffffffff814fe694>] dev_set_promiscuity+0x24/0x50
[62852.052194] [<ffffffffa0324795>] vlan_dev_open+0xd5/0x1f0 [8021q]
[62852.052196] [<ffffffff814fe58f>] __dev_open+0xbf/0x140
[62852.052198] [<ffffffff814fe88d>] __dev_change_flags+0x9d/0x170
[62852.052200] [<ffffffff814fe989>] dev_change_flags+0x29/0x60
The above comes from the setting the vlan device to IFF_UP state.
[62852.053569] [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.053571] [<ffffffffa032459b>] ? vlan_dev_set_rx_mode+0x2b/0x30
[8021q]
[62852.053573] [<ffffffff814fe8d5>] __dev_change_flags+0xe5/0x170
[62852.053645] [<ffffffff814fe989>] dev_change_flags+0x29/0x60
[62852.053647] [<ffffffffa032334a>] vlan_device_event+0x18a/0x690
[8021q]
[62852.053649] [<ffffffff8161036c>] notifier_call_chain+0x4c/0x70
[62852.053651] [<ffffffff8109d456>] raw_notifier_call_chain+0x16/0x20
[62852.053653] [<ffffffff814f744d>] call_netdevice_notifiers+0x2d/0x60
[62852.053654] [<ffffffff814fe1a3>] __dev_notify_flags+0x33/0xa0
[62852.053656] [<ffffffff814fe9b2>] dev_change_flags+0x52/0x60
[62852.053657] [<ffffffff8150cd57>] do_setlink+0x397/0xa40
And this one comes from the notification code. What we end
up with is a vlan with promiscuity count of 1 and and a physical
device with a promiscuity count of 2. They should both have
a count 1.
To resolve this issue, vlan code can use dev_get_flags() api
which correctly masks promiscuity and allmulti flags.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise tests are always true here because it uses '|' where '&' is
intended.
Fixes: 98b5a0f4a2 ('net: macb: Add support for jumbo frames')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the imx27 documentation, fec has a 4 Kbyte
memory space map. Moreover, the actual 16 Kbyte mapping
overlaps the SCC (Security Controller) memory register
space. So, we reduce the memory register space to 4 Kbyte.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9f0749e3eb ("ARM i.MX27: Add devicetree support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fresh mounts of proc and sysfs are a very special case that works very
much like a bind mount. Unfortunately the current structure can not
preserve the MNT_LOCK... mount flags. Therefore refactor the logic
into a form that can be modified to preserve those lock bits.
Add a new filesystem flag FS_USERNS_VISIBLE that requires some mount
of the filesystem be fully visible in the current mount namespace,
before the filesystem may be mounted.
Move the logic for calling fs_fully_visible from proc and sysfs into
fs/namespace.c where it has greater access to mount namespace state.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
of_machine_is_compatible() seems to be preferred over soc_is_exynos4().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
On Exynos4412 boards (Trats2, Odroid U3) after enabling L2 cache in
56b60b8bce ("ARM: 8265/1: dts: exynos4: Add nodes for L2 cache
controller") the second suspend to RAM failed. First suspend worked fine
but the next one hang just after powering down of secondary CPUs (system
consumed energy as it would be running but was not responsive).
The issue was caused by enabling delayed reset assertion for CPU0 just
after issuing power down of cores. This was introduced for Exynos4 in
13cfa6c4f7 ("ARM: EXYNOS: Fix CPU idle clock down after CPU off").
The whole behavior is not well documented but after checking with vendor
code this should be done like this (on Exynos4):
1. Enable delayed reset assertion when system is running (for all CPUs).
2. Disable delayed reset assertion before suspending the system.
This can be done after powering off secondary CPUs.
3. Re-enable the delayed reset assertion when system is resumed.
Fixes: 13cfa6c4f7 ("ARM: EXYNOS: Fix CPU idle clock down after CPU off")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The name "ftrace" really refers to the function hook infrastructure. It
is not about the trace_events. The function ftrace_get_offsets_##call()
is used to find the offset into dynamically allocated trace event fields
for printing. It has nothing to do with function tracing. Rename it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The name "ftrace" really refers to the function hook infrastructure. It
is not about the trace_events. The function ftrace_define_fields_##call()
is used to define how to process the trace_event fields. It has nothing to
do with function tracing. Rename it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The name "ftrace" really refers to the function hook infrastructure. It
is not about the trace_events. The structure ftrace_event_type_funcs_##call
is used to define how the trace_events will be printed. It has nothing to
do with function tracing. Rename it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The name "ftrace" really refers to the function hook infrastructure. It
is not about the trace_events. The structure ftrace_data_offset_##call is
used to find the offsets of dynamically allocated fields in trace_events.
It has nothing to do with function tracing. Rename it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The name "ftrace" really refers to the function hook infrastructure. It
is not about the trace_events. The ftrace_raw_##call structures are built
by macros for trace events. They have nothing to do with function tracing.
Rename them.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
curaddrupper caches the last written upper 32-bits of a dma address
(the device has one register for the upper 32-bits of all dma
address registers). The problem is, not every dma address write
checks and sets curaddrupper. This causes the driver to occasionally
not write the upper 32-bits of a dma address to the device when it
really should.
I've seen this manifest particularly when the driver is trying to
read config data from the device (RCONFIG) in order to checksum the
device's eeprom. Since the device writes its config data to the
wrong DMA address the driver reads 0 as the eeprom size and the
eeprom checksum fails.
This patch fixes the issue by removing curaddrupper and always
writing the upper 32-bits of dma addresses.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per TODO. This commit introduces no functional changes.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3188-radxarock.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3066a-bqcurie2.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Make sure that async function scheduled with async_schedule() has already
been executed.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If ACPI is disabled there's no need to schedule an async function call,
the driver initialization can be aborted earlier in acpi_battery_init().
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When I had inlined __alloc_rx_skb into __netdev_alloc_skb and
__napi_alloc_skb I had overlooked the fact that there was a return in the
__alloc_rx_skb. As a result we weren't reserving headroom or setting the
skb->dev in certain cases. This change corrects that by adding a couple of
jump labels to jump to depending on __alloc_skb either succeeding or failing.
Fixes: 9451980a66 ("net: Use cached copy of pfmemalloc to avoid accessing page")
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce invalid_phys_cpuid() to identify cpu with invalid
physical ID, then used it as replacement of the direct comparisons
with PHYS_CPUID_INVALID.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since invalid_logical_cpuid() can check error values, so
return specific error instead of -1 for acpi_map_cpuid().
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use pr->phys_id to replace phys_id to simplify the code.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Just use pr->id instead of cpu_index to simplify the code.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Before xen_acpi_processor_enable() is called, struct acpi_processor *pr is
allocated in xen_acpi_processor_add() and checked if it's NULL, so no need
to check again when passed to xen_acpi_processor_enable(), just remove it.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use invalid_logical_cpuid(pr->id) instead of direct comparison.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ACPI processor drivers, we use direct comparisons of cpu logical
id with -1 which are error prone in case logical cpuid is accidentally
assinged an error code and prevents us from returning an error-encoding
cpuid directly in some cases.
So introduce invalid_logical_cpuid() to identify cpu with invalid
logical cpu num, then it will be used to replace the direct comparisons
with -1.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix an oops during device initialization by correctly setting size_of_priv
instead of leaving it 0.
The regression was introduced by 8abe4a0a3f ("[media] dib7000:
export just one symbol") and only fixed for one type of dib0700 based
devices in 9e334c7564 ("[media] Fix regression in some dib0700
based devices").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=92301
Fixes: 8abe4a0a3f ("[media] dib7000: export just one symbol")
Cc: stable@vger.kernel.org # for version 3.17+
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes a compile warnning "dump_num maybe used uninitialized in
this function".
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
