All the necessary debug uart mapping is already being done in
debug_ll_io_init, there's no need for it here.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Now the debug and platsmp.S are fixed for big endian, the
architecture can now advertise big endian support.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Update the secondary code to allow the secondary boot to work when the
system is running big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
If the 8250 debug code is used in word mode on an big endian
host then the writes need to be change into little endian for
the bus.
Note, we have to re-convert the value back as the debug code
will inspect the value after writing it to see if a newline
has been written.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add all the clock nodes for the Arria10 platform. At the same time, update
the peripherals with their respective clocks property.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add the l4_sys_free_clk node
Conditions per spi_transfer are:
* transfer.len >= 96 bytes (to avoid mapping overhead costs)
* transfer.len < 65536 bytes (limitaion by spi-hw block - could get extended)
* an individual scatter/gather transfer length must be a multiple of 4
for anything but the last transfer - spi-hw block limit.
(some shortcut has been taken in can_dma to avoid unnecessary mapping of
pages which, for which there is a chance that there is a split with a
transfer length not a multiple of 4)
If it becomes a necessity these restrictions can get removed by additional
code.
Note that this patch requires a patch to dma-bcm2835.c by Noralf to
enable scatter-gather mode inside the dmaengine, which has not been
merged yet.
That is why no patch to arch/arm/boot/dts/bcm2835.dtsi is included - the
code works as before without dma when tx/rx are not set, but it writes
a message warning about dma not used:
spi-bcm2835 20204000.spi: no tx-dma configuration found - not using dma mode
To enable dma-mode add the following lines to the device-tree:
dmas = <&dma 6>, <&dma 7>;
dma-names = "tx", "rx";
Tested-by: Noralf Trønnes <noralf@tronnes.org> (private communication)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only left enqueue_root() user is netem, and it looks not necessary :
qdisc_skb_cb(skb)->pkt_len is preserved after one skb_clone()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one return statement instead of two to simplify the code.
Both are returning the same value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tx-fifo-depth and rx-fifo-depth devicetree properties for socfpga
stmmac. These devicetree properties will be used to configure certain
features of the stmmac on the socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add multicast-filter-bins and perfect-filter-entries configuration properties
to the socfpga devicetree for the Arria 10 socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The CIU(Card Interface Unit) get its clock from the sdmmc_clk_divided clock
which is used to clock the card. The sdmmc_clk_divided clock is the sdmmc_clk
passed through a fixed divider of 4. This patch adds the sdmmc_clk_divided
node and makes the sdmmc_clk it's parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: renamed ciu_clk to sdmmc_clk_divided
Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.
Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Arria10 devkit is using UART1 for the debug uart port. Remove
unused aliases.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add removal of unused aliases
Add status = "disabled" in the base DTSI for Arria10. The SDMMC and uart
nodes should be enabled in the appropriate board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds the DTS bindings for the adxl34x digital
accelerometer.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Three fixes have queued up:
* Reference count fix in the AMD IOMMUv2 driver
* Sign extension fix in the ARM-SMMU driver
* Build fix for rockchip driver with device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=f34j
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Three fixes have queued up:
- reference count fix in the AMD IOMMUv2 driver
- sign extension fix in the ARM-SMMU driver
- build fix for rockchip driver with device tree"
* tag 'iommu-fixes-v4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: Fix sign-extension of upstream bus addresses at stage 1
iommu/rockchip: Fix build without CONFIG_OF
iommu/amd: Fix bug in put_pasid_state_wait
This enables the ethtool's "-d" and "--register-dump"
options for fec devices.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org>
Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Pull crypto fixes from Herbert Xu:
"This fixes a the implementation of CRC32 on arm64 where it incorrectly
applied negation on the result.
It also fixes the arm64 implementations of SHA/SHA256 where in some
cases it may end up finalising the result twice"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/sha2-ce - prevent asm code finalization in final() path
crypto: arm64/sha1-ce - prevent asm code finalization in final() path
crypto: arm64/crc32 - bring in line with generic CRC32
Pull libata fixes from Tejun Heo:
"Rather big for fixes pull.
- SCC controllers never lived to see the light of the day. Both
libata and ide drivers removed.
- In some configurations, link power management policy changes
sometimes cause delayed spurious PHY events which can develop into
noticeable failures. This has been reported several times over the
years. Gabriele's patches suppress PHY events for a while after
LPM policy changes which should help most of these failures without
causing too much problem for hotplug use cases.
- A few controller specific fixes"
[ Hmm. I don't think removing SSC support is really a "fix", but hey, it
removes a lot of lines of code. Which I like. So ... good riddance ]
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: avoton port-disable reset-quirk
ata: select DW_DMAC in case of SATA_DWC
libata: Blacklist queued TRIM on all Samsung 800-series
libata: Ignore spurious PHY event on LPM policy change
libata: Add helper to determine when PHY events should be ignored
ata: ahci_st: fixup layering violations / drvdata errors
Remove celleb-only SCC PATA drivers
This patch adds a new file describing the sysfs entries for the
toshiba_haps driver.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch makes use of DEVICE_ATTR_{RW, WO} macros, simplifying
device attributes creation.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply replaces the use of sscanf with kstrtoint returning
the error code in case that something went bad.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply bumps the driver version to 0.22, as significant
changes were made to the driver, such as cleanups, updated events,
keymap handling, fixes and the bluetooth rfkill code removal.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch removes the check for TOS_FAILURE whenever we are using
the tci_raw function call, as that code is only returned by the
{hci, sci}_{read, write} functions and never by the tci_raw, and
thus making that check irrelevant.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply does some misc cleanup to comments, mainly
capitalizes some left over comments from a previous clean up and
adds some comments at the beginning of some feature function calls,
as well as some misc changes to some comments.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply renames the hci_{read, write}1 functions to
hci_{read, write}.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch removes the hci_{read, write}2 functions from the driver,
and the toshiba_hotkey_event_type_get function was adapted to use the
tci_raw function.
The hci_write2 function was only used by the bluetooth rfkill code,
but since its removal, it was causing build warnings, and the
hci_read2 function was only used by the toshiba_hotkey_event_type_get
function.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The function toshiba_bluetooth_status is currently printing the
status of the device whenever it is queried, but since the
introduction of the rfkill poll code, this value will get printed
everytime the poll occurs.
This patch removes the status message from the *_status function, and
adds a debug message to the *_sync_status function printing the
bluetooth device raw status, killswitch, plug and power states of the
device as well.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This should have been #ifdef not #if.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: d2788d3488 ("net: sched: further simplify handle_ing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of these are related to the new "batched stripe writeout",
but there are a few others.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIVAwUAVVAgfznsnt1WYoG5AQKNsBAAw+yXVnRlLfzTPOhiIolvdmdmck6ghpV7
eTHTbDEVkDo+a+caU01mhkHtL2wEuxGqr4XHTASIM9Xjn2YLhH14HOtBPl6+IddR
F58X+SN8/pK4tzc5P42AAbfGfqeJSBPSl49L94+Pd9BsagNYZOUx7c/WK5lKay6O
ZQRvI3Bafg7VTzHCw931sN11yY/PS+45zpOentk5TlavRPcZfuVTh1QzSyAUvbtN
sAFK2+ISflj8+TW0rLo44c3kkC7ARFKcq5lJt4WsQUntJTjiIROvqvaEP+IUZkGr
y+yvCJbskJ6B03XrcuvdkFrp3Qe0yWtHCN6qKhc8AI/c/pcuz24xTYQ6V6LDyAy8
N2z6m1Kri97qxZpOONNh31WOCmVyFmwiz7+54soEeTDg3xgTb60UiZe8T+9ZcxoY
sN8ksVSGGapgQUUGYcidbZla6uSWNjZq9hQgDJFUwG3HhvT3E/qiUT9kqAxfPsLE
Vxw/KQ5GkW+7ldaPmGuv29hc3THjsiLY5Bx0kBlmgao3fcT61WbNcZPJOQfMxlT7
6qoJSiNoq612TaHj3X06FXhMGE/fwjwjOO+PpULxM47giHcKrVR/qlG4kREYa2vj
UgV05rP/S+k3Mce4dHzvUuE57t0ADff0d/mZvhfzERjNdwTMdWgia89XLg7D06rk
UGB/o2IwWug=
=tapF
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc3-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few fixes for md.
Most of these are related to the new "batched stripe writeout", but
there are a few others"
* tag 'md/4.1-rc3-fixes' of git://neil.brown.name/md:
md/raid5: fix handling of degraded stripes in batches.
md/raid5: fix allocation of 'scribble' array.
md/raid5: don't record new size if resize_stripes fails.
md/raid5: avoid reading parity blocks for full-stripe write to degraded array
md/raid5: more incorrect BUG_ON in handle_stripe_fill.
md/raid5: new alloc_stripe() to allocate an initialize a stripe.
md-raid0: conditional mddev->queue access to suit dm-raid
In WRED mode, the backlog for a single virtual queue (VQ) should not be
used to determine queue behavior; instead the backlog is summed across
all VQs. This sum is currently used when calculating the average queue
lengths. It also needs to be used when determining if the queue's hard
limit has been reached, or when reporting each VQ's backlog via netlink.
q->backlog will only be used if the queue switches out of WRED mode.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.
Fix the binding documentation so the property is properly specified.
Fixes: 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mark Brown <broonie@kernel.org>
As I was testing with hwsim, I missed that my previous commit to
make LED work depend on activation broke the code because I missed
removing the old trigger struct and some code was still using it,
now erroneously, causing crashes.
Fix this by always using the correct struct.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After receiving a PADT and the socket is closed, user space will no
longer drop the reference to the pppoe device.
This leads to errors like this:
[ 488.570000] unregister_netdevice: waiting for eth0.2 to become free. Usage count = 2
Fixes: 287f3a943f ("pppoe: Use workqueue to die properly when a PADT is received")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts 4fbdf9cb it breaks LPFC on POWER7 machine, big endian kernel.
Without this, the kernel enters an infinite oops loop.
This is the hardware used for verification:
0005:01:00.0 Fibre Channel [0c04]: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host Adapter [10df:f100] (rev 03)
0005:01:00.1 Fibre Channel [0c04]: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host Adapter [10df:f100] (rev 03)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The pointers to the 2nd level page tables are converted to 1st level
page table entries, which means kmemleak can't find them and assumes
they have been leaked. Call kmemleak_ignore on the 2nd level page
tables to prevent them from showing up in kmemleak reports.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Set the SRB flags correctly when there is no data transfer. Without this
change some IHV drivers will fail valid commands such as TEST_UNIT_READY.
Cc: <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Stage 1 translation is controlled by two sets of page tables (TTBR0 and
TTBR1) which grow up and down from zero respectively in the ARMv8
translation regime. For the SMMU, we only care about TTBR0 and, in the
case of a 48-bit virtual space, we expect to map virtual addresses 0x0
through to 0xffff_ffff_ffff.
Given that some masters may be incapable of emitting virtual addresses
targetting TTBR1 (e.g. because they sit on a 48-bit bus), the SMMU
architecture allows bit 47 to be sign-extended, halving the virtual
range of TTBR0 but allowing TTBR1 to be used. This is controlled by the
SEP field in TTBCR2.
The SMMU driver incorrectly enables this sign-extension feature, which
causes problems when userspace addresses are programmed into a master
device with the SMMU expecting to map the incoming transactions via
TTBR0; if the top bit of address is set, we will instead get a
translation fault since TTBR1 walks are disabled in the TTBCR.
This patch fixes the issue by disabling sign-extension of a fixed
virtual address bit and instead basing the behaviour on the upstream bus
size: the incoming address is zero extended unless the upstream bus is
only 49 bits wide, in which case bit 48 is used as the sign bit and is
replicated to the upper bits.
Cc: <stable@vger.kernel.org> # v4.0+
Reported-by: Varun Sethi <varun.sethi@freescale.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Also drop the unnecessary check at the beginning of the
uda1380_set_bias_level() which compares the current level to the target
level and aborts if they are the same. Since the core will not call the
set_bias_level() callback if we already are in the target state the result
of the check is always false.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
