Use enum to represent table offsets rather than hard-coding numbers to avoid
problems with the numbers becoming out of sync with the table.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Synopsys SDP platform uses DW GPIO controller in design with
ARC cores. So adding ARC to architectures that may select this
GPIO controller.
Even though support for Synopsys SDP is yet to be submitted we'll need
this tiny option enabled at least for properly working interrupts (DW
GPIO controller is used as interrupt controller).
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
Add a enum_map file in the tracing directory to see what enums have been
saved to convert in the print fmt files.
As this requires the enum mapping to be persistent in memory, it is only
created if the new config option CONFIG_TRACE_ENUM_MAP_FILE is enabled.
This is for debugging and will increase the persistent memory footprint
of the kernel.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The enums used in tracepoints for __print_symbolic() do not have their
values shown in the tracepoint format files and this makes it difficult
for user space tools to convert the binary values to the strings they
are to represent.
Add TRACE_DEFINE_ENUM(x) macros to export the enum names to their values
to make the tracing output from user space tools more robust.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add an userdata set extension and allow the user to attach arbitrary
data to set elements. This is intended to hold TLV encoded data like
comments or DNS annotations that have no meaning to the kernel.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a new "dynset" expression for dynamic set updates.
A new set op ->update() is added which, for non existant elements,
invokes an initialization callback and inserts the new element.
For both new or existing elements the extenstion pointer is returned
to the caller to optionally perform timer updates or other actions.
Element removal is not supported so far, however that seems to be a
rather exotic need and can be added later on.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently a set binding is assumed to be related to a lookup and, in
case of maps, a data load.
In order to use bindings for set updates, the loop detection checks
must be restricted to map operations only. Add a flags member to the
binding struct to hold the set "action" flags such as NFT_SET_MAP,
and perform loop detection based on these.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use atomic operations for the element count to avoid races with async
updates.
To properly handle the transactional semantics during netlink updates,
deleted but not yet committed elements are accounted for seperately and
are treated as being already removed. This means for the duration of
a netlink transaction, the limit might be exceeded by the amount of
elements deleted. Set implementations must be prepared to handle this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The NFT_SET_TIMEOUT flag is ignore in nft_select_set_ops, which may
lead to selection of a set implementation that doesn't actually
support timeouts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Enums used by tracepoints for __print_symbolic() are shown in the
tracepoint format files with just their names and not their values.
This makes it difficult for user space tools to know how to convert the
binary data into their string representations.
By adding the use of TRACE_DEFINE_ENUM(), the enum names will be mapped
to their values and shown in the tracing file system to let tools
convert the data as necessary.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
commit 3de07e5aaf290a0b58919 ("drivers: gpio: use devm_kzalloc")
introduce devm_kzalloc() for allocating the memory. In this case kfree
is not required to use. Above commit id introduced the bug that kfree
is not removed from the remove function.
This patch fix the above bug.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
nf_bridge_info->mask is used for several things, for example to
remember if skb->pkt_type was set to OTHER_HOST.
For a bridge, OTHER_HOST is expected case. For ip forward its a non-starter
though -- routing expects PACKET_HOST.
Bridge netfilter thus changes OTHER_HOST to PACKET_HOST before hook
invocation and then un-does it after hook traversal.
This information is irrelevant outside of br_netfilter.
After this change, ->mask now only contains flags that need to be
known outside of br_netfilter in fast-path.
Future patch changes mask into a 2bit state field in sk_buff, so that
we can remove skb->nf_bridge pointer for good and consider all remaining
places that access nf_bridge info content a not-so fastpath.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
->mask is a bit info field that mixes various use cases.
In particular, we have flags that are mutually exlusive, and flags that
are only used within br_netfilter while others need to be exposed to
other parts of the kernel.
Remove BRNF_8021Q/PPPoE flags. They're mutually exclusive and only
needed within br_netfilter context.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't access skb->nf_bridge directly, this pointer will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
right now we store this in the nf_bridge_info struct, accessible
via skb->nf_bridge. This patch prepares removal of this pointer from skb:
Instead of using skb->nf_bridge->x, we use helpers to obtain the in/out
device (or ifindexes).
Followup patches to netfilter will then allow nf_bridge_info to be
obtained by a call into the br_netfilter core, rather than keeping a
pointer to it in sk_buff.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_netfilter maintains an extra state, nf_bridge_info, which is attached
to skb via skb->nf_bridge pointer.
Amongst other things we use skb->nf_bridge->data to store the original
mac header for every processed skb.
This is required for ip refragmentation when using conntrack
on top of bridge, because ip_fragment doesn't copy it from original skb.
However there is no need anymore to do this unconditionally.
Move this to the one place where its needed -- when br_netfilter calls
ip_fragment().
Also switch to percpu storage for this so we can handle fragmenting
without accessing nf_bridge meta data.
Only user left is neigh resolution when DNAT is detected, to hold
the original source mac address (neigh resolution builds new mac header
using bridge mac), so rename ->data and reduce its size to whats needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently in xt_socket, we take advantage of early demuxed sockets
since commit 00028aa370 ("netfilter: xt_socket: use IP early demux")
in order to avoid a second socket lookup in the fast path, but we
only make partial use of this:
We still unnecessarily parse headers, extract proto, {s,d}addr and
{s,d}ports from the skb data, accessing possible conntrack information,
etc even though we were not even calling into the socket lookup via
xt_socket_get_sock_{v4,v6}() due to skb->sk hit, meaning those cycles
can be spared.
After this patch, we only proceed the slower, manual lookup path
when we have a skb->sk miss, thus time to match verdict for early
demuxed sockets will improve further, which might be i.e. interesting
for use cases such as mentioned in 681f130f39 ("netfilter: xt_socket:
add XT_SOCKET_NOWILDCARD flag").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the driver uses handle_simple_irq for all IRQ types and hard
codes the acknowledge for different IRQ types into the handler. It is
better to use the IRQ core as intended and let it handle the differences
between the various types of IRQ. For example the current system does
not work for threaded level triggered IRQs as these need to be masked
until the threaded handler has run.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All Marvell EBU SoCs (Kirkwood, Dove, Orion, Armada) have the
capability of changing the location of their internal registers (i.e
the registers for most hardware blocks inside the SoC). When coming
out of reset, the internal registers are mapped at 0xd0000000, but
since years and years, the tradition has been to have the internal
registers remapped at 0xf1000000 by the bootloader, and Linux has
since then assumed that the internal registers for the SoC were
located at 0xf1000000 on Kirkwood, Dove, Orion, etc. Linux has never
been aware that those registers are remappable (and there is no way to
know where they are mapped at runtime, since the register to configure
the address of the registers is itself within the internal registers).
Then came the Armada 370 and Armada XP, in which some of the very
early silicon steppings had an issue, which forced to use 0xd0000000:
the SoC was no longer working properly when the internal registers
were remapped at 0xf1000000. This issue is only affecting very early
silicon steppings and production steppings are not affected: the issue
has been fixed in between.
Since what we (Free Electrons) used to do the initial submission of
the Armada 370 and Armada XP platforms was evaluation boards with
those very early steppings, we submitted Device Tree that assumed the
internal registers were mapped at 0xd0000000. This is the case for
Armada 370 DB, Armada XP DB and Armada XP GP.
However, in practice, since Marvell has been shipping the evaluation
boards with production steppings of the SoC, they are shipping those
boards with bootloaders that remap the registers to 0xf1000000. We
have already changed this internal register address to 0xf1000000 for
the Armada XP DB in commit 82066bdb5a and for the Armada XP GP in
commit 91ed32200e (both merged in v3.15).
We only recently got our hand on an Armada 370 DB with a production
stepping of the SoC, which uses a bootloader that remaps internal
registers at 0xf1000000. Therefore, this commit aligns the Armada 370
DB to be like the Armada XP DB and Armada XP GP: assume that the
internal registers are mapped at 0xf1000000.
We would like to stress out the fact that the usage of 0xd0000000 as
the internal register base address was a temporary workaround for
early steppings deficiencies, and that the real long-term solution is
the usage of 0xf1000000. Having 0xd0000000 is an *accident* in the
life of the Marvell platform support in the kernel, as is confirmed by
the usage of 0xf1000000 in all previous Marvell platforms (Dove,
Kirkwood, Orion).
There are unfortunately a number of commercial devices that continue
to use 0xd0000000 even though they use production steppings of the
SoC, simply because the vendors of such devices have never bothered
using a more recent bootloader version from Marvell. There is not much
we can do about it, and we plan on keeping 0xd0000000 in the Device
Tree of such devices.
The main reason for remapping the internal registers at 0xf1000000
instead of 0xd0000000 is that it leaves more space in the 0 -> 4 GB
part of the physical address space for RAM. With registers at
0xd0000000, all RAM between 0xd0000000 to 0xffffffff is lost because
it's covered by the I/O registers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedameon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov:
9ece8839b1 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7 +
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
quotad periodically syncs in-memory quotas to the ondisk quota file
and sets the QDF_REFRESH flag so that a subsequent read of a synced
quota is re-read from disk.
gfs2_quota_lock() checks for this flag and sets a 'force' bit to
force re-read from disk if requested. However, there is a race
condition here. It is possible for gfs2_quota_lock() to find the
QDF_REFRESH flag unset (i.e force=0) and quotad comes in immediately
after and syncs the relevant quota and sets the QDF_REFRESH flag.
gfs2_quota_lock() resumes with force=0 and uses the stale in-memory
quota usage values that result in miscalculations.
This patch fixes this race by moving the check for the QDF_REFRESH
flag check further out into the gfs2_quota_lock() process, i.e, in
do_glock(), under the protection of the quota glock.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
The AES implementation still assumes, that the hw_desc[0] has a valid
key as long as no new key needs to be set; consequentialy it always
sets the AES key header for the first descriptor and puts data into
the second one (hw_desc[1]).
Change this to only update the key in the hardware, when a new key is
to be set and use the first descriptor for data otherwise.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With commit
7e77bdebff crypto: af_alg - fix backlog handling
in place, the backlog works under all circumstances where it previously failed, atleast
for the sahara driver. Use it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function crypto_alg_match returns an algorithm without taking
any references on it. This means that the algorithm can be freed
at any time, therefore all users of crypto_alg_match are buggy.
This patch fixes this by taking a reference count on the algorithm
to prevent such races.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The output buffer is used for CPU access, so
the API should be dma_sync_single_for_cpu which
makes the cache line invalid in order to reload
the value in memory.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The input buffer and output buffer are mapped for DMA transfer
in Atmel AES driver. But they are also be used by CPU when
the requested crypt length is not bigger than the threshold
value 16. The buffers will be cached in cache line when CPU
accessed them. When DMA uses the buffers again, the memory
can happened to be flushed by cache while DMA starts transfer.
So using API dma_sync_single_for_device and dma_sync_single_for_cpu
in DMA to ensure DMA coherence and CPU always access the correct
value. This fix the issue that the encrypted result periodically goes
wrong when doing performance test with OpenSSH.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kernel will report "BUG: spinlock lockup suspected on CPU#0"
when CONFIG_DEBUG_SPINLOCK is enabled in kernel config and the
spinlock is used at the first time. It's caused by uninitialized
spinlock, so just initialize it in probe.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kernel will report "BUG: spinlock lockup suspected on CPU#0"
when CONFIG_DEBUG_SPINLOCK is enabled in kernel config and the
spinlock is used at the first time. It's caused by uninitialized
spinlock, so just initialize it in probe.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The maximum source and destination burst size is 16
according to the datasheet of Atmel DMA. And the value
is also checked in function at_xdmac_csize of Atmel
DMA driver. With the restrict, the value beyond maximum
value will not be processed in DMA driver, so SHA384 and
SHA512 will not work and the program will wait forever.
So here change the max burst size of all the cases to 16
in order to make SHA384 and SHA512 work and keep consistent
with DMA driver and datasheet.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kernel will report "BUG: spinlock lockup suspected on CPU#0"
when CONFIG_DEBUG_SPINLOCK is enabled in kernel config and the
spinlock is used at the first time. It's caused by uninitialized
spinlock, so just initialize it in probe.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Having a zero length sg doesn't mean it is the end of the sg list. This
case happens when calculating HMAC of IPSec packet.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When a hash is requested on data bigger than the buffer allocated by the
SHA driver, the way DMA transfers are performed is quite strange:
The buffer is filled at each update request. When full, a DMA transfer
is done. On next update request, another DMA transfer is done. Then we
wait to have a full buffer (or the end of the data) to perform the dma
transfer. Such a situation lead sometimes, on SAMA5D4, to a case where
dma transfer is finished but the data ready irq never comes. Moreover
hash was incorrect in this case.
With this patch, dma transfers are only performed when the buffer is
full or when there is no more data. So it removes the transfer whose size
is equal the update size after the full buffer transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add new version of atmel-sha available with SAMA5D4 devices.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add new version of atmel-aes available with SAMA5D4 devices.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adding 'I' event modifier to have complete set of modifiers for
perf_event_attr:exclude_* bits.
Any event specified with 'I' modifier will have the
perf_event_attr:exclude_idle bit set.
$ perf record -e cycles:I -vv ls 2>&1 | grep exclude_idle
exclude_hv 0 exclude_idle 1
Adding automated tests.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lkml.kernel.org/r/1428441919-23099-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
report__warn_kptr_restrict() calls map__kmap(kernel_map) before checking
kernel_map againest NULL.
Which is dangerous, since map__kmap() will return a invalid and not NULL
address.
It will trigger a warning message in map__kmap() after the patch "perf:
kmaps: enforce usage of kmaps to protect futher bugs." was applied.
This patch fixes it by adding the missing checking.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1428490772-135393-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Following commit:
1a59413124 perf: Add wakeup watermark control to the AUX area
enlarged perf_event_attr, but did not updated attr tests.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Markus T Metzger <markus.t.metzger@intel.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/n/20150407171715.GA22603@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit 9b118acae3 ("perf probe: Fix to
handle aliased symbols in glibc") uses an absolute format '%lx' to
print u64 argument, which causes compiling error on ARM 32.
This patch replaces it with PRIx64.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1428459274-138470-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The enums used in the tracepoints for __print_symbolic() have their
names shown in the tracepoint format files. User space tools do not know
how to convert those names into their values to be able to convert the
binary data.
Use TRACE_DEFINE_ENUM() to export the enum names to their values for
userspace to do the parsing correctly.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Acked-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The enums used in tracepoints with __print_symbolic() have their
names shown in the tracepoint format files and not their values.
This makes it difficult for user space tools to convert the binary
data to the strings as user space does not know what those enums
are about.
By having them use TRACE_DEFINE_ENUM(), the names of the enums will
be mapped to the values and shown to user space.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The enums used by the softirq mapping is what is shown in the output
of the __print_symbolic() and not their values, that are needed
to map them to their strings. Export them to userspace with the
TRACE_DEFINE_ENUM() macro so that user space tools can map the enums
with their values.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The tracepoints that use __print_symbolic() use enums as the value
to convert to strings. Unfortunately, the format files for these
tracepoints show the enum name and not their value. This causes some
userspace tools not to know how to convert __print_symbolic() to
their strings.
Add TRACE_DEFINE_ENUM() macros to export the enums used to userspace
to let those tools know what those enum values are.
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Pankaj Kumar <pankaj.km@samsung.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The tracepoints in the 9p code use a lot of enums for the __print_symbolic()
function. These enums are shown in the tracepoint format files, and user
space tools such as trace-cmd does not have the information to parse it.
Add helper macros to export the enums with TRACE_DEFINE_ENUM().
Link: http://lkml.kernel.org/r/20150403013802.220157513@goodmis.org
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
