For consistency, allocate a new crtc_state for a crtc that is being
disabled. Previously only the enabled value of the current state would
change.
v2: Rebase on v5 of previous patch. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Resolve rebase conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because setup_earlycon() continues to attempt console registration
if an error occurred parsing the option string, the actual value of
the error code from parse_options() is ignored.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If parsing failed to decode a valid uart addr, return -ENODEV instead
of success. Although setup_earlycon() will detect the failure anyway
(because the write() method has not been set), that behavior is not
obvious and should not be relied on.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The <baud><parity><bit> option string is not supplied if the earlycon
is started via devicetree and OF_EARLYCON_DECLARE(). The option string
is also not required if started via kernel command line parameters of
the form:
earlycon=uart,mmio,<addr>
console=uart,mmio,<addr>
If earlycon_device->baud is 0, then an option string was not supplied.
In this case, assume the uart has already been initialized by the
bootloader or firmware.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializing the ->uartclk field is not related to option parsing;
relocate from parse_options() to setup_earlycon() (which mirrors the
behavior of of_setup_earlycon()).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
early_device was only required for serial8250_find_port_for_earlycon(),
which was replaced by extensible console matching.
Fixup early_serial8250_write() to get the earlycon_device * from
console->data (which is initialized by {of_}setup_earlycon()).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'/**' is required to start a kernel-doc comment block.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).
The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.
Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the atomic conversion, the mode set paths need to be changed to rely
on an atomic state instead of using the staged config. By using an
atomic state for the legacy code, we will be able to convert the code
base in small chunks.
v2: Squash patch that adds stat argument to intel_set_mode(). (Ander)
Make every caller of intel_set_mode() allocate state. (Daniel)
Call drm_atomic_state_clear() in set config's error path. (Daniel)
v3: Copy staged config to atomic state in force restore path. (Ander)
v4: Don't update ->new_config for disabled pipes in __intel_set_mode(),
since it is expected to be NULL in that case. (Ander)
v5: Don't change return type of intel_modeset_pipe_config(). (Chandra)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Remove spurious ret local variable due to changes in v5.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for 8250 split; initialize the port flags based on the
"skip_txen_test" module param to use the existing flag test.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250_core.c file split; move shared inline function
to local header file.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since uart->port.type has just reset to PORT_UNKNOWN, capabilities
are reset to uart_config[PORT_UNKNOWN].flags, which is 0.
Removes unnecessary dependency on uart_config[].
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; calculate the ttyS index directly from
the port minor which avoids the global serial8250_reg reference
from base port operations.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_parse_gic_cpu_interface calls acpi_map_gic_cpu_interface by both
passing a 32-bit value in the u8 enabled parameter and then subsequently
ignoring its return value.
Sort it out.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If acpi=force is passed on the command line, it forces ACPI to be
the only available boot method, hence it must be left enabled even
if the initialization and sanity checks on ACPI tables fails.
This patch refactors ACPI initialization to prevent disabling ACPI
if acpi=force is passed on the command line.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Current ACPI init code on ARM64 relies on acpi_table_parse() API to
check if the FADT is present and to carry out sanity checks on that.
The handler passed to the acpi_table_parse() function and used to
carry out the parsing on the requested table returns a value that is
ignored by the acpi_table_parse() function, so it is not possible
to propagate errors back to the acpi_table_parse() caller through
the handler.
This forces ARM64 ACPI init code to have disable_acpi() calls scattered
all over the place that makes code unwieldy and not easy to follow.
This patch refactors the ARM64 ACPI init code, by creating a
self-contained function (ie acpi_fadt_sanity_check()) that carries
out the required checks on FADT and returns an adequate return value
to the caller. This allows creating a common error path that disables
ACPI and makes code more readable and easy to parse and change were
further checks FADT to be added in the future.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
PSCI v0.2+ allows the kernel to probe the PSCI firmware version.
This patch replaces the default initialization of PSCI v0.2+
functions with code that allows probing PSCI firmware version
and initializes PSCI functions accordingly.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
PSCI v0.2+ versions provide a specific PSCI call (PSCI_VERSION) to
detect the PSCI version at run-time. Current PSCI v0.2 init code
carries out the version probing in the PSCI 0.2 DT init function,
but the version probing does not depend on DT so it can be factored out
in order to make it available to other boot mechanisms (ie ACPI) to
reuse. The psci_probe() probing function can be easily extended
to add detection and initialization of PSCI functions defined in
PSCI versions >0.2.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The code deployed to implement GSI linux IRQ numbers mapping on arm64 turns
out to be generic enough so that it can be moved to ACPI core code along
with its respective config option ACPI_GENERIC_GSI selectable on
architectures that can reuse the same code.
Current ACPI IRQ mapping code is not integrated in the kernel IRQ domain
infrastructure, in particular there is no way to look-up the
IRQ domain associated with a particular interrupt controller, so this
first version of GSI generic code carries out the GSI<->IRQ mapping relying
on the IRQ default domain which is supposed to be always set on a
specific architecture in case the domain structure passed to
irq_create/find_mapping() functions is missing.
This patch moves the arm64 acpi functions that implement the gsi mappings:
acpi_gsi_to_irq()
acpi_register_gsi()
acpi_unregister_gsi()
to ACPI core code. Since the generic GSI<->domain mapping is based on IRQ
domains, it can be extended as soon as a way to map an interrupt
controller to an IRQ domain is implemented for ACPI in the IRQ domain
layer.
x86 and ia64 code for GSI mappings cannot rely on the generic GSI
layer at present for legacy reasons, so they do not select the
ACPI_GENERIC_GSI config options and keep relying on their arch
specific GSI mapping layer.
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since the policy is that once we pass acpi=force in the early
param, we will not unflatten device tree even if ACPI is disabled
in ACPI table init fails, so fix the code by comparinging both
acpi_disabled and param_acpi_force before the device tree is
unflattened.
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
One more documentation file are also being added:
A section by section review of the ACPI spec (acpi_object_usage.txt)
to note recommendations and prohibitions on the use of the numerous
ACPI tables and objects. This sets out the current expectations of
the firmware by Linux very explicitly (or as explicitly as I can, for
now).
CC: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
CC: Yi Li <phoenix.liyi@huawei.com>
CC: Mark Langsdorf <mlangsdo@redhat.com>
CC: Ashwin Chaugule <ashwinc@codeaurora.org>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add documentation for the guidelines of how to use ACPI
on ARM64.
Reviewed-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Mark Langsdorf <mlangsdo@redhat.com>
Reviewed-by: Ashwin Chaugule <ashwinc@codeaurora.org>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add Kconfigs to build ACPI on ARM64, and make ACPI available on ARM64.
acpi_idle driver is x86/IA64 dependent now, so make CONFIG_ACPI_PROCESSOR
depend on X86 || IA64, and implement it on ARM64 in the future.
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When ACPI is enabled on ARM64, XEN ACPI will also compiled
into the kernel, but XEN ACPI is x86 dependent, so introduce
CONFIG_XEN_ACPI to make it depend on x86 before XEN ACPI is
functional on ARM64.
CC: Julien Grall <julien.grall@linaro.org>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: David Vrabel <david.vrabel@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ACPI reduced hardware mode is disabled by default, but ARM64
can only run properly in ACPI hardware reduced mode, so select
ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64.
If the firmware is not using hardware reduced ACPI mode, we
will disable ACPI to avoid nightmare such as accessing some
registers which are not available on ARM64.
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Using the information presented by GTDT (Generic Timer Description Table)
to initialize the arch timer (not memory-mapped).
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Originally-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ACPI kernel uses MADT table for proper GIC initialization. It needs to
parse GIC related subtables, collect CPU interface and distributor
addresses and call driver initialization function (which is hardware
abstraction agnostic). In a similar way, FDT initialize GICv1/2.
NOTE: This commit allow to initialize GICv1/2 basic functionality.
While now simple GICv2 init call is used, any further GIC features
require generic infrastructure for proper ACPI irqchip initialization.
That mechanism and stacked irqdomains to support GICv2 MSI/virtualization
extension, GICv3/4 and its ITS are considered as next steps.
CC: Jason Cooper <jason@lakedaemon.net>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Introduce ACPI_IRQ_MODEL_GIC which is needed for ARM64 as GIC is
used, and then register device's gsi with the core IRQ subsystem.
acpi_register_gsi() is similar to DT based irq_of_parse_and_map(),
since gsi is unique in the system, so use hwirq number directly
for the mapping.
We are going to implement stacked domains when GICv2m, GICv3, ITS
support are added.
CC: Marc Zyngier <marc.zyngier@arm.com>
Originally-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Introduce a new function map_gicc_mpidr() to allow MPIDRs to be obtained
from the GICC Structure introduced by ACPI 5.1, since MPIDR for ARM64 is
64-bit, so typedef u64 for phys_cpuid_t.
The ARM architecture defines the MPIDR register as the CPU hardware
identifier. This patch adds the code infrastructure to retrieve the MPIDR
values from the ARM ACPI GICC structure in order to look-up the kernel CPU
hardware ids required by the ACPI core code to identify CPUs.
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CPU hardware ID (phys_id) is defined as u32 in structure acpi_processor,
but phys_id is used as int in acpi processor driver, so it will lead to
some inconsistence for the drivers.
Furthermore, to cater for ACPI arch ports that implement 64 bits CPU
ids a generic CPU physical id type is required.
So introduce typedef u32 phys_cpuid_t in a common file, and introduce
a macro PHYS_CPUID_INVALID as (phys_cpuid_t)(-1) if it's not defined
by other archs, this will solve the inconsistence in acpi processor driver,
and will prepare for the ACPI on ARM64 for the 64 bit CPU hardware ID
in the following patch.
CC: Rafael J Wysocki <rjw@rjwysocki.net>
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[hj: reworked cpu physid map return codes]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
UART drivers that share ttyS namespace cannot trivially compute the
ttyS index from the port->line value since the minor_start may be
offset from minor 64. Further, to do so requires a pointer to the
uart driver since there is no back pointer from uart_port to
uart_driver.
Rather than have UART drivers computing the minor value by themselves,
encapsulate within the serial core at port registration time.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch fixes following sparse warning:
n_gsm.c:2827:22: warning: symbol 'tty_ldisc_packet' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of manual calls of device_create_file() and
device_remove_file(), pass the static attribute groups using
device_create_with_groups().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add irq disable and enable in bfin_serial_rx_dma_timeout in case of
system hang.
This reverts part of commit 9642dbe73c ("serial: bfin-uart: avoid
dead lock in rx irq handler in smp kernel").
Signed-off-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are needed by other modules, the related error with allmodconfig:
MODPOST 3327 modules
ERROR: "L1P_cache_block_invalidate" [drivers/misc/lkdtm.ko] undefined!
ERROR: "L1D_cache_block_writeback" [drivers/misc/lkdtm.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Or can not pass building with allmodconfig:
LD init/built-in.o
drivers/built-in.o: In function `vgacon_switch':
vgacon.c:(.text+0x47f8): undefined reference to `screen_info'
vgacon.c:(.text+0x4810): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_resize':
vgacon.c:(.text+0x4ac8): undefined reference to `screen_info'
vgacon.c:(.text+0x4acc): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_save_screen':
vgacon.c:(.text+0x4cc8): undefined reference to `screen_info'
drivers/built-in.o:vgacon.c:(.text+0x4cd0): more undefined references to `screen_info' follow
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Or it will cause building break with allmodconfig:
CC [M] drivers/tty/serial/8250/8250_core.o
drivers/tty/serial/8250/8250_core.c:102:24: fatal error: asm/serial.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
c6x does not implement get_dma_ops() for dma-mapping-common.h. And in
dma-mapping-common.h, dma_sync_single_range_for_device() may be dummy.
So c6x can just define a dummy function for allmodconfig building.
CC [M] drivers/net/ethernet/micrel/ks8851.o
drivers/net/ethernet/micrel/ks8842.c: In function 'ks8842_tx_frame_dma':
drivers/net/ethernet/micrel/ks8842.c:453:2: error: implicit declaration of function 'dma_sync_single_range_for_device' [-Werror=implicit-function-declaration]
dma_sync_single_range_for_device(adapter->dev,
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Some modules may assume "asm/setup.h" already include all headers which
needed by itself. So need let "asm/setup.h" include "linux/types.h", the
related error:
C [M] drivers/input/joydev.o
In file included from include/asm-generic/page.h:23:0,
from ./arch/c6x/include/asm/page.h:9,
from include/asm-generic/io.h:14,
from arch/c6x/include/generated/asm/io.h:1,
from drivers/input/joydev.c:15:
./arch/c6x/include/asm/setup.h:17:27: error: unknown type name 'phys_addr_t'
extern int c6x_add_memory(phys_addr_t start, unsigned long size);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
For supporting uClinux flat-format executables, c6x needs to define the
fewest features to support it, at present, xtensa architecture has the
fewest feature for it, so just copy xtensa flat.h. The related error:
CC fs/binfmt_flat.o
In file included from fs/binfmt_flat.c:36:0:
include/linux/flat.h:12:22: fatal error: asm/flat.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
early_init_dt_scan() accepts "void *", the related warning:
CC arch/c6x/kernel/setup.o
arch/c6x/kernel/setup.c: In function 'machine_init':
arch/c6x/kernel/setup.c:290:21: warning: passing argument 1 of 'early_init_dt_scan' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
early_init_dt_scan(fdt);
^
In file included from arch/c6x/kernel/setup.c:19:0:
include/linux/of_fdt.h:75:13: note: expected 'void *' but argument is of type 'const void *'
extern bool early_init_dt_scan(void *params);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
For gcc5 c6x raw compiler, at present, it may not define __linux__, so
c6x kernel still needs to define __linux__ just like another archs have
done. The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64:0,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221:2: error: unknown type name 'u_quad_t'
u_quad_t va_size; /* file size in bytes */
^
include/uapi/linux/coda.h:229:2: error: unknown type name 'u_quad_t'
u_quad_t va_bytes; /* bytes of disk space held by file */
^
include/uapi/linux/coda.h:230:2: error: unknown type name 'u_quad_t'
u_quad_t va_filerev; /* file modification number */
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
time_init invokes timer64_init (which is __init annotation)
since all of these are invoked at init time, lets maintain
consistency by ensuring time_init is marked appropriately
as well.
This fixes the following warning with CONFIG_DEBUG_SECTION_MISMATCH=y
WARNING: vmlinux.o(.text+0x3bfc): Section mismatch in reference from the function time_init() to the function .init.text:timer64_init()
The function time_init() references
the function __init timer64_init().
This is often because time_init lacks a __init
annotation or the annotation of timer64_init is wrong.
Fixes: 546a39546c ("C6X: time management")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Fix the passing of big endian data to routines that will be writing
it to the bus in the wrong order.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The S2MPS11 PMIC (present on Arndale Octa board) has the same RTC module
as S2MPS14 device. Add respective mfd cell to enable it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API consolidation only and
should make things more readable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
