This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdb
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit 72859d91d9.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Denys says:
TEST with zero will always set ZF. Thus, "jnz send_interrupts" never jumps.
We get interrupts regularly enough that this didn't cause immediate problems.
Reported-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We currently use the device tree update code in the kernel after resuming
from a suspend operation to re-sync the kernels view of the device tree with
that of the hypervisor. The code as it stands is not endian safe as it relies
on parsing buffers returned by RTAS calls that thusly contains data in big
endian format.
This patch annotates variables and structure members with __be types as well
as performing necessary byte swaps to cpu endian for data that needs to be
parsed.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Cyril Bur <cyrilbur@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a new variant of POWER8 coming called "POWER8 with NVLink". The
core is identical to POWER8 but unfortunately they strapped it with a
different PVR, so we need to add an explicit entry for it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we can now use hypervisor doorbells for host IPIs, this makes
sure we clear the host IPI flag when taking a doorbell interrupt, and
clears any pending doorbell IPI in pnv_smp_cpu_kill_self() (as we
already do for IPIs sent via the XICS interrupt controller). Otherwise
if there did happen to be a leftover pending doorbell interrupt for
an offline CPU thread for any reason, it would prevent that thread from
going into a power-saving mode; it would instead keep waking up because
of the interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The M7 processor has a different hypervisor group id and different PCR fast
trap values. PIC read/write functions and PCR bit fields are the same as
the T4 so those are reused.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently perf-stat (aka, counting mode) does not work:
$ perf stat ls
...
Performance counter stats for 'ls':
1.585665 task-clock (msec) # 0.580 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.054 M/sec
<not supported> cycles
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
<not supported> instructions
<not supported> branches
<not supported> branch-misses
0.002735100 seconds time elapsed
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
1.552890 task-clock (msec) # 0.552 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.055 M/sec
5,748,997 cycles # 3.702 GHz
<not supported> stalled-cycles-frontend:HG
<not supported> stalled-cycles-backend:HG
1,684,362 instructions:HG # 0.29 insns per cycle
295,133 branches:HG # 190.054 M/sec
28,007 branch-misses:HG # 9.49% of all branches
0.002815665 seconds time elapsed
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perf_pmu_disable is called by core perf code before pmu->del and the
enable function is called by core perf code afterwards. No need to
call again within sparc_pmu_del.
Ditto for pmu->add and sparc_pmu_add.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'arg' argument to copy_thread() is only ever used when forking a new
kernel thread. Hence, rename it to 'kthread_arg' for clarity.
Signed-off-by: Alex Dowad <alexinbeijing@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Round up min_size respectively round down max_size to the next power
of two to make sure we always respect the limit specified by the
user. This is required because we compare the table size against the
limit before we expand or shrink.
Also fixes a minor bug where we modified min_size in the params
provided instead of the copy stored in struct rhashtable.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
"An update to Synaptics driver that makes it usable with the 2015
lineup from Lenovo"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
Input: synaptics - remove X250 from the topbuttonpad list
Input: synaptics - remove X1 Carbon 3rd gen from the topbuttonpad list
Input: synaptics - re-route tracksticks buttons on the Lenovo 2015 series
Input: synaptics - remove TOPBUTTONPAD property for Lenovos 2015
Input: synaptics - retrieve the extended capabilities in query $10
Input: synaptics - do not retrieve the board id on old firmwares
Input: synaptics - handle spurious release of trackstick buttons
Input: synaptics - fix middle button on Lenovo 2015 products
Input: synaptics - skip quirks when post-2013 dimensions
Input: synaptics - support min/max board id in min_max_pnpid_table
Input: synaptics - remove obsolete min/max quirk for X240
Input: synaptics - query min dimensions for fw v8.1
Input: synaptics - log queried and quirked dimension values
Input: synaptics - split synaptics_resolution(), query first
Pull overlayfs fixes from Miklos Szeredi:
"This fixes minor issues with the multi-layer update in v4.0"
* 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: upper fs should not be R/O
ovl: check lowerdir amount for non-upper mount
ovl: print error message for invalid mount options
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and
sleep context save in the Baytrail driver.
- Make default output directions work properly in the
Cherryview driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in
the sunxi driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qp0z
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a slew of pin control fixes I've accumulated for the v4.0
kernel. Nothing special, just driver fixes (mainly embedded Intel it
seems) and a misunderstanding regarding the stub functions was
reverted:
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and sleep context
save in the Baytrail driver.
- Make default output directions work properly in the Cherryview
driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in the sunxi
driver"
* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
pinctrl: at91: move lock/unlock_as_irq calls into request/release
pinctrl: update direction_output function of cherryview driver
pinctrl: baytrail: Save pin context over system sleep
pinctrl: baytrail: Rework interrupt handling
pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
pinctrl: baytrail: Relax GPIO request rules
Revert "pinctrl: consumer: use correct retval for placeholder functions"
The tracing events for regmap are confined to the regmap subsystem. It
also requires accessing an internal header. Instead of including the
internal header from a generic file location, move the tracing file
into the regmap directory.
Also rename the regmap tracing header to trace.h, as it is redundant to
keep the regmap.h name when it is in the regmap directory.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform_quirk element in the platform data was used
to change the way the IRQ is triggered. When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.
Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.
This will allow us to use standard irq DT definitions
later on.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fix spelling typos in Documentations/input.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This avoids repeating the logic in every Makefile. We mimic the
top-level Makefile and use $(CROSS_COMPILE)gcc.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
OPTIMIZER_HIDE_VAR(), as defined when using gcc, is insufficient to
ensure protection from dead store optimization.
For the random driver and crypto drivers, calls are emitted ...
$ gdb vmlinux
(gdb) disassemble memzero_explicit
Dump of assembler code for function memzero_explicit:
0xffffffff813a18b0 <+0>: push %rbp
0xffffffff813a18b1 <+1>: mov %rsi,%rdx
0xffffffff813a18b4 <+4>: xor %esi,%esi
0xffffffff813a18b6 <+6>: mov %rsp,%rbp
0xffffffff813a18b9 <+9>: callq 0xffffffff813a7120 <memset>
0xffffffff813a18be <+14>: pop %rbp
0xffffffff813a18bf <+15>: retq
End of assembler dump.
(gdb) disassemble extract_entropy
[...]
0xffffffff814a5009 <+313>: mov %r12,%rdi
0xffffffff814a500c <+316>: mov $0xa,%esi
0xffffffff814a5011 <+321>: callq 0xffffffff813a18b0 <memzero_explicit>
0xffffffff814a5016 <+326>: mov -0x48(%rbp),%rax
[...]
... but in case in future we might use facilities such as LTO, then
OPTIMIZER_HIDE_VAR() is not sufficient to protect gcc from a possible
eviction of the memset(). We have to use a compiler barrier instead.
Minimal test example when we assume memzero_explicit() would *not* be
a call, but would have been *inlined* instead:
static inline void memzero_explicit(void *s, size_t count)
{
memset(s, 0, count);
<foo>
}
int main(void)
{
char buff[20];
snprintf(buff, sizeof(buff) - 1, "test");
printf("%s", buff);
memzero_explicit(buff, sizeof(buff));
return 0;
}
With <foo> := OPTIMIZER_HIDE_VAR():
(gdb) disassemble main
Dump of assembler code for function main:
[...]
0x0000000000400464 <+36>: callq 0x400410 <printf@plt>
0x0000000000400469 <+41>: xor %eax,%eax
0x000000000040046b <+43>: add $0x28,%rsp
0x000000000040046f <+47>: retq
End of assembler dump.
With <foo> := barrier():
(gdb) disassemble main
Dump of assembler code for function main:
[...]
0x0000000000400464 <+36>: callq 0x400410 <printf@plt>
0x0000000000400469 <+41>: movq $0x0,(%rsp)
0x0000000000400471 <+49>: movq $0x0,0x8(%rsp)
0x000000000040047a <+58>: movl $0x0,0x10(%rsp)
0x0000000000400482 <+66>: xor %eax,%eax
0x0000000000400484 <+68>: add $0x28,%rsp
0x0000000000400488 <+72>: retq
End of assembler dump.
As can be seen, movq, movq, movl are being emitted inlined
via memset().
Reference: http://thread.gmane.org/gmane.linux.kernel.cryptoapi/13764/
Fixes: d4c5efdb97 ("random: add and use memzero_explicit() for clearing data")
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: mancha security <mancha1@zoho.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull IDE fix from David Miller:
"Just one fix to convert a by-hand conversion of jiffies to msecs, from
Nicholas McGuire"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide_tape: convert jiffies with jiffies_to_msecs
Pull sparc fixes from David Miller:
1) Some command cases of semtimedop() not even handled due to miscoded
comparison on sparc64. From Rob Gardner.
2) Due to two bugs, /proc/kcore wan't working properly on sparc.
3) Make sure fatal traps stop all running cpus, from Dave Kleikamp.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix /proc/kcore
sparc: semtimedop() unreachable due to comparison error
sparc: io_64.h: Replace io function-link macros
sparc64: fatal trap should stop all cpus
arch: sparc: kernel: starfire.c: Remove unused function
arch: sparc: kernel: traps_64.c: Remove some unused functions
We can't directly call ipv6_sock_mc_join() but should use the stub
instead and protect it around IS_ENABLED.
Fixes: d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu_get_pgd isn't used anywhere and is Probably Not What You Want.
Remove it before anybody decides to use it.
Signed-off-by: Will Deacon <will.deacon@arm.com>
According to the arm64 boot protocol, registers x1 to x3 should be
zero upon kernel entry, and non-zero values are reserved for future
use. This future use is going to be problematic if we never enforce
the current rules, so start enforcing them now, by emitting a warning
if non-zero values are detected.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This removes the function __calc_phys_offset and all open coded
virtual to physical address translations using the offset kept
in x28.
Instead, just use absolute or PC-relative symbol references as
appropriate when referring to virtual or physical addresses,
respectively.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enabling of the MMU is split into two functions, with an align and
a branch in the middle. On arm64, the entire kernel Image is ID mapped
so this is really not necessary, and we can just merge it into a
single function.
Also replaces an open coded adrp/add reference to __enable_mmu pair
with adr_l.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Replace the confusing virtual/physical address arithmetic with a simple
PC-relative reference.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This removes the confusing __switch_data object from head.S,
and replaces it with standard PC-relative references to the
various symbols it encapsulates.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The global processor_id is assigned the MIDR_EL1 value of the boot
CPU in the early init code, but is never referenced afterwards.
As the relevance of the MIDR_EL1 value of the boot CPU is debatable
anyway, especially under big.LITTLE, let's remove it before anyone
starts using it.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
