of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'flags' was missing in ndo_bridge_setlink().
ndo_bridge_dellink() was missing.
Fixes: 407af3299e ("bridge: Add netlink interface to configure vlans on bridge ports")
Fixes: add511b382 ("bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink")
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nick Piggin is currently listed as the maintainer of BRD in MAINTAINERS,
but the mails sent to the listed address are returned as undeliverable.
Update the maintainer for BRD to be Jens Axboe, since patches for BRD
flow up through him.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Scorpion supports a set of local performance monitor event
selection registers (LPM) sitting behind a cp15 based interface
that extend the architected PMU events to include Scorpion CPU
and Venum VFP specific events. To use these events the user is
expected to program the lpm register with the event code shifted
into the group they care about and then point the PMNx event at
that region+group combo by writing a LPMn_GROUPx event. Add
support for this hardware.
Note: the raw event number is a pure software construct that
allows us to map the multi-dimensional number space of regions,
groups, and event codes into a flat event number space suitable
for use by the perf framework.
This is based on code originally written by Sheetal Sahasrabudhe,
Ashwin Chaugule, and Neil Leeder [1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm/tree/arch/arm/kernel/perf_event_msm.c?h=msm-3.4
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Neil Leeder <nleeder@codeaurora.org>
Cc: Ashwin Chaugule <ashwinc@codeaurora.org>
Cc: Sheetal Sahasrabudhe <sheetals@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Krait specific PMxEVCNTCR register is unpredictable upon
reset. Currently we clear the register before we setup an event,
but we don't need to do that. Instead, we can iterate through all
the events and clear them once when we reset the PMU, saving a
write in the event setup path.
Cc: Neil Leeder <nleeder@codeaurora.org>
Cc: Ashwin Chaugule <ashwinc@codeaurora.org>
Cc: Sheetal Sahasrabudhe <sheetals@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Do some things to make the Krait PMU support code generic enough
to be used by the Scorpion PMU support code.
* Rename the venum register functions to be venum instead of krait
specific because the same registers exist on Scorpion
* Add some macros to decode our Krait specific event encoding that's
the same on Scorpion (modulo an extra region).
* Drop 'krait' from krait_clear_pmresrn_group() so it can be used
by Scorpion code
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Exynos cpuidle driver has coupled cpuidle built-in so it cannot be
built without SMP:
arch/arm/mach-exynos/pm.c: In function 'exynos_cpu0_enter_aftr':
arch/arm/mach-exynos/pm.c:246:4: error: implicit declaration of function 'arch_send_wakeup_ipi_mask' [-Werror=implicit-function-declaration]
arch/arm/mach-exynos/built-in.o: In function 'exynos_pre_enter_aftr':
../arch/arm/mach-exynos/pm.c:300: undefined reference to 'cpu_boot_reg_base'
arch/arm/mach-exynos/built-in.o: In function 'exynos_cpu1_powerdown':
../arch/arm/mach-exynos/pm.c:282: undefined reference to 'exynos_cpu_power_down'
Fix it by adding missing checks for SMP.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
OS X version 10.10.2 (and possibly older versions) doesn't support LE
Secure Connections but incorrectly copies all authentication request
bits from a Security Request to its Pairing Request. The result is that
an SC capable initiator (such as BlueZ) will think OS X intends to do SC
when in fact it's incapable of it:
< ACL Data TX: Handle 3585 flags 0x00 dlen 6
SMP: Security Request (0x0b) len 1
Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
SMP: Pairing Request (0x01) len 6
IO capability: KeyboardDisplay (0x04)
OOB data: Authentication data not present (0x00)
Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
Max encryption key size: 16
Initiator key distribution: EncKey (0x01)
Responder key distribution: EncKey IdKey Sign (0x07)
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
SMP: Pairing Response (0x02) len 6
IO capability: NoInputNoOutput (0x03)
OOB data: Authentication data not present (0x00)
Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
Max encryption key size: 16
Initiator key distribution: EncKey (0x01)
Responder key distribution: EncKey Sign (0x05)
The pairing eventually fails when we get an unexpected Pairing Confirm
PDU instead of a Public Key PDU:
> ACL Data RX: Handle 3585 flags 0x02 dlen 21
SMP: Pairing Confirm (0x03) len 16
Confim value: bcc3bed31b8f313a78ec3cce32685faf
It is only at this point that we can speculate that the remote doesn't
really support SC. This patch creates a workaround for the just-works
model, however the MITM case is unsolvable because the OS X user has
already been requested to enter a PIN which we're now expected to
randomly generate and show the user (i.e. a chicken-and-egg problem).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The two main fixes here from Javier and Doug both fix issues seen on the
Exynos-based ARM Chromebooks with reference counting of GPIO regulators
over system suspend. The GPIO enable code didn't properly take account
of this cases (a full analysis is in Doug's commit log). This is fixed
by both fixing the reference counting directly and by making the resume
code skip enables it doesn't need to do. We could skip the change in
the resume code but it's a very simple change and adds extra robustness
against problems in other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCBjKAAoJECTWi3JdVIfQiA4H/2/zS+bEGIJs0yquAsmNT0as
v1XW+K8pw8klcCUbUpBgeqwBDmhiHHJtL5AWuC68KZHLRmg4+ryRdCyUgZ51AyJ4
4obGKxVrWpO0xM3BLeoeCc0ZSAAQzVuxplFSyFEbE14ULUKBqsVS8YKD2+FyrDRL
0RPAdNDak2Z7HD60W6234qqGfmEW0e1NAYTuZ7sCjE4dp8+S8OeauuwT489tuGt7
7N+BusHHnjWASW3tcitANTE8f3l3K4b5sUueolxi+ZghnrcxHcZn7LlKbVj0tpiF
yOCjc6jiLUL5UiCZ5q5IhamKPCTpTf/9LJlsjoSmj3Ze4PXn9/rEPW3wrIUyAh4=
=Dxlj
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The two main fixes here from Javier and Doug both fix issues seen on
the Exynos-based ARM Chromebooks with reference counting of GPIO
regulators over system suspend. The GPIO enable code didn't properly
take account of this case (a full analysis is in Doug's commit log).
This is fixed by both fixing the reference counting directly and by
making the resume code skip enables it doesn't need to do. We could
skip the change in the resume code but it's a very simple change and
adds extra robustness against problems in other drivers"
* tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65910: Add missing #include <linux/of.h>
regulator: core: Fix enable GPIO reference counting
regulator: Only enable disabled regulators on resume
Disable the pm_runtime of the device upon remove. This is
added to balance the pm_runtime_enable() invoked in the probe.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few things here:
- A change from Lars to fix insertion of cache values at the start of
rather than end of a rbtree block. This hadn't been noticed before
since almost everything lists registers in ascending order.
- A fix from Takashi for spurious warnings during cache sync with read
once registers, a problem which can be very noticeable on devices
that it affects.
- A fix from Valentin for a tighening of the oneshot IRQ request
interface which would have broken affected devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCAncAAoJECTWi3JdVIfQ3UwH/R94Youeta69sJvSpao38Luo
jSj6A+zA2x2azwOTNdZ8F4vdqetoabvt8enXR0zxQnx86JP3zYFoEZcos7Bn4HRX
E85Fn8RNLHVP0NmUdZefvSztG5A0Glf9FxEqoSfGb6r0FztYnjJ3fCEoDO8NYE8S
xkeFvznLyPGeU39BMXuqROEUN4BNVeQ6ijIQBsP9tIpgIQA9lIzW4vSqTXvGiwLU
UrPTYpPpVukKGwYD6UB8GQ14M3KDAmzvSTiCO7hal1NUdgtOWqObR2YALhMWBV6z
bygbobrVGaaxmdb3maEol3h9tCxY6G+5Pcwhl0JDZdVd2McXa2oMMxQ/r1kgcxY=
=t8iv
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A few things here:
- a change from Lars to fix insertion of cache values at the start of
rather than end of a rbtree block. This hadn't been noticed before
since almost everything lists registers in ascending order.
- a fix from Takashi for spurious warnings during cache sync with
read once registers, a problem which can be very noticeable on
devices that it affects.
- a fix from Valentin for a tighening of the oneshot IRQ request
interface which would have broken affected devices"
* tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Fix present bitmap resize
regmap: Skip read-only registers in regcache_sync()
regmap-irq: set IRQF_ONESHOT flag to ensure IRQ request
more minor issues with our virtio 1.0 drivers just introduced in the
kernel.
(I would normally use my fixes branch for this, but there were a batch of them...)
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8QwR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"Not entirely surprising: the ongoing QEMU work on virtio 1.0 has
revealed more minor issues with our virtio 1.0 drivers just introduced
in the kernel.
(I would normally use my fixes branch for this, but there were a batch
of them...)"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_mmio: fix access width for mmio
uapi/virtio_scsi: allow overriding CDB/SENSE size
virtio_mmio: generation support
virtio_rpmsg: set DRIVER_OK before using device
9p/trans_virtio: fix hot-unplug
virtio-balloon: do not call blocking ops when !TASK_RUNNING
virtio_blk: fix comment for virtio 1.0
virtio_blk: typo fix
virtio_balloon: set DRIVER_OK before using device
virtio_console: avoid config access from irq
virtio_console: init work unconditionally
Since 32b0aa9aae ("ARM: EXYNOS: Remove i2c sys configuration related
code") the Exynos 5250 no longer saves additional registers under
'exynos_pm_data.extra_save' field.
No one else uses this code so get rid of it making also 'exynos_pm_data'
const everywhere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The 'exynos5420_pm_data' is not modified and can be made const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The 'pm_data', 'exynos_release_ret_regs', 'exynos3250_release_ret_regs'
and 'exynos5420_release_ret_regs' are not exported nor used outside of
suspend.c file. Make them static.
This fixes following sparse warnings:
arch/arm/mach-exynos/suspend.c:83:23: warning: symbol 'pm_data' was not declared. Should it be static?
arch/arm/mach-exynos/suspend.c:106:14: warning: symbol 'exynos_release_ret_regs' was not declared. Should it be static?
arch/arm/mach-exynos/suspend.c:117:14: warning: symbol 'exynos5420_release_ret_regs' was not declared. Should it be static?
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull kvm fixes from Marcelo Tosatti:
"KVM bug fixes (ARM and x86)"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm/arm64: KVM: Keep elrsr/aisr in sync with software model
KVM: VMX: Set msr bitmap correctly if vcpu is in guest mode
arm/arm64: KVM: fix missing unlock on error in kvm_vgic_create()
kvm: x86: i8259: return initialized data on invalid-size read
arm64: KVM: Fix outdated comment about VTCR_EL2.PS
arm64: KVM: Do not use pgd_index to index stage-2 pgd
arm64: KVM: Fix stage-2 PGD allocation to have per-page refcounting
kvm: move advertising of KVM_CAP_IRQFD to common code
The power domain nodes in DTS may be very generic (e.g. "power-domain"
for Exynos 5420) making it very hard to debug:
$ cat /sys/kernel/debug/pm_genpd/pm_genpd_summary
domain status slaves
power-domain on
Use platform device name instead so the names will be a little more
user friendly:
domain status slaves
100440e0.power-domain on
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Suggested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos Chromebooks have an Embedded Controller known as the ChromeOS EC
Enable the driver that provides an interface to access from user-space.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Both GSCALER IPs in gsc power domain have async-bridges (to FIMD and MIXER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
FIMD and MIXER IPs in disp1 power domain have async-bridges (to GSCALER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds bindings for clocks required by async-bridges
present in the particular power domain.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since Exynos5420 there are async-bridges (ASB) between different IPs. These
bridges must be operational during power domain on/off, ie. clocks used
by these bridges should be enabled.
This patch enabled these clocks during domain on/off.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The mgmt.c file should be reserved purely for HCI_CHANNEL_CONTROL. The
mgmt_control() function in it is already completely generic and has a
single user in hci_sock.c. This patch moves the function there and
renames it a bit more appropriately to hci_mgmt_cmd() (as it's a command
dispatcher).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to make the mgmt command handling more generic we can't have a
direct call to mgmt_init_hdev() from mgmt_control(). This patch adds a
new callback to struct hci_mgmt_chan. And sets it to point to the
mgmt_init_hdev() function for the HCI_CHANNEL_CONTROL instance.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several mgmt protocol features that will be needed by more
than just the current HCI_CHANNEL_CONTROL. These include sending generic
events as well as handling pending commands. This patch moves these
functions out from mgmt.c to a new mgmt_util.c file.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to have pending commands for different HCI channels we need
to be able to distinguish for which channel a command was sent to. The
channel information is already part of the socket data and can be
fetched using the recently added hci_sock_get_channel() function. To not
require all mgmt.c code to pass an extra channel parameter this patch
also adds a helper pending_find() & pending_find_data() functions which
act as a wrapper to the new mgmt_pending_find() & mgmt_pending_find_data()
APIs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll need to have access to which HCI channel a socket is bound to, in
order to manage pending mgmt commands in clean way. This patch adds a
helper for the purpose.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit f4f75ad5 ("efi: efistub: Convert into static library")
introduced a static library for EFI stub, libstub.
The EFI libstub directory is referenced by the kernel build system via
a obj subdirectory rule in:
drivers/firmware/efi/Makefile
Unfortunately, arm64 also references the EFI libstub via:
libs-$(CONFIG_EFI_STUB) += drivers/firmware/efi/libstub/
If we're unlucky, the kernel build system can enter libstub via two
simultaneous threads resulting in build failures such as:
fixdep: error opening depfile: drivers/firmware/efi/libstub/.efi-stub-helper.o.d: No such file or directory
scripts/Makefile.build:257: recipe for target 'drivers/firmware/efi/libstub/efi-stub-helper.o' failed
make[1]: *** [drivers/firmware/efi/libstub/efi-stub-helper.o] Error 2
Makefile:939: recipe for target 'drivers/firmware/efi/libstub' failed
make: *** [drivers/firmware/efi/libstub] Error 2
make: *** Waiting for unfinished jobs....
This patch adjusts the arm64 Makefile to reference the compiled library
explicitly (as is currently done in x86), rather than the directory.
Fixes: f4f75ad5 efi: efistub: Convert into static library
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently don't log the boot mode for arm64 as we do for arm, and
without KVM the user is provided with no indication as to which mode(s)
CPUs were booted in, which can seriously hinder debugging in some cases.
Add logging to the boot path once all CPUs are up. Where CPUs are
mismatched in violation of the boot protocol, WARN and set a taint (as
we do for CPU other CPU feature mismatches) given that the
firmware/bootloader is buggy and should be fixed.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 828e9834e9 ("arm64: head: create a new function for setting
the boot_cpu_mode flag") added BOOT_CPU_MODE_EL1, a nonzero value
replacing uses of zero. However it failed to update __boot_cpu_mode
appropriately.
A CPU booted at EL2 writes BOOT_CPU_MODE_EL2 to __boot_cpu_mode[0], and
a CPU booted at EL1 writes BOOT_CPU_MODE_EL1 to __boot_cpu_mode[1].
Later is_hyp_mode_mismatched() determines there to be a mismatch if
__boot_cpu_mode[0] != __boot_cpu_mode[1].
If all CPUs are booted at EL1, __boot_cpu_mode[0] will be set to
BOOT_CPU_MODE_EL1, but __boot_cpu_mode[1] will retain its initial value
of zero, and is_hyp_mode_mismatched will erroneously determine that the
boot modes are mismatched. This hasn't been a problem so far, but later
patches which will make use of is_hyp_mode_mismatched() expect it to
work correctly.
This patch initialises __boot_cpu_mode[1] to BOOT_CPU_MODE_EL1, fixing
the erroneous mismatch detection when all CPUs are booted at EL1.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently we only perform alternative patching for kernels built with
CONFIG_SMP, as we call apply_alternatives_all() in smp.c, which is only
built for CONFIG_SMP. Thus !SMP kernels may not have necessary
alternatives patched in.
This patch ensures that we call apply_alternatives_all() once all CPUs
are booted, even for !SMP kernels, by having the smp_init_cpus() stub
call this for !SMP kernels via up_late_init. A new wrapper,
do_post_cpus_up_work, is added so we can hook other calls here later
(e.g. boot mode logging).
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: e039ee4ee3 ("arm64: add alternative runtime patching")
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869A,
such as the one found on the Jetway JNF99-525 motherboard, to the f7188x
gpio driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869, such
as the one found on the Jetway NF96u-525 motherboard, to the f7188x gpio
driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Tested-by: Les Schaffer <schaffer@optonline.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The company is called "Fintek", not "Fintech". Fix it.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 1feb57a245
"gpio: add parameter to allow the use named gpios"
includes a double-consted array. What we want is not
const const * but const * const (const pointer to const
data). Fix this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Olliver Schinagl <oliver@schinagl.nl>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Configure the pins in external interrupt mode, as done for Snow in
e5e5c6d14e ("ARM: dts: Add power and lid GPIO keys pinctrl for
exynos5250-snow").
Reported-by: Kukjin Kim <kgene@kernel.org>
Suggested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
As pointed by recent post[1] on exploiting DRAM physical imperfection,
/proc/PID/pagemap exposes sensitive information which can be used to do
attacks.
This disallows anybody without CAP_SYS_ADMIN to read the pagemap.
[1] http://googleprojectzero.blogspot.com/2015/03/exploiting-dram-rowhammer-bug-to-gain.html
[ Eventually we might want to do anything more finegrained, but for now
this is the simple model. - Linus ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Seaborn <mseaborn@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CSR controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Intel controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Atheros controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When doing scan through mgmt api, some controllers can do both le and
classic scan at same time. They can be distinguished by
HCI_QUIRK_SIMULTANEOUS_DISCOVERY set.
This patch enables them to use this feature when doing dual mode scan.
Instead of doing le, then classic scan, both scans are run at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch refactor BR/EDR inquiry and LE scan triggering logic into
separate methods.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controllers allow both LE scan and BR/EDR inquiry to run at
the same time, while others allow only one, LE SCAN or BR/EDR
inquiry at given time.
Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core wether given controller can
do both LE scan and BR/EDR inquiry at same time.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Resolve a merge conflict with mmc refactoring aaa25a5a33 ("ARM: dts:
unuse the slot-node and deprecate the supports-highspeed for dw-mmc in
exynos") by dropping the slot@0 nodes, moving its bus-width property to
the mmc node and replacing supports-highspeed with cap-{mmc,sd}-highspeed,
matching exynos5250-snow.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add a tuning knob so we can adjust the dirtytime expiration timeout,
which is very useful for testing lazytime.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Jan Kara pointed out that if there is an inode which is constantly
getting dirtied with I_DIRTY_PAGES, an inode with an updated timestamp
will never be written since inode->dirtied_when is constantly getting
updated. We fix this by adding an extra field to the inode,
dirtied_time_when, so inodes with a stale dirtytime can get detected
and handled.
In addition, if we have a dirtytime inode caused by an atime update,
and there is no write activity on the file system, we need to have a
secondary system to make sure these inodes get written out. We do
this by setting up a second delayed work structure which wakes up the
CPU much more rarely compared to writeback_expire_centisecs.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Current Exynos CPU idle driver supports entering AFTR (Arm Off, Top
Running) mode on Exynos 4210 (coupled), Exynos 4x12 and Exynos 5250.
Enable it in default configuration to reduce energy consumption.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a MMC/SDIO
Marvell WiFi-Ex chip. This patch enables wireless support and the
mwifiex driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
