At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.
Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Add support for a new SoC: Armada 39x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9RvwACgkQCwYYjhRyO9UGwQCfXlE0v/h5zAG6j/LTAFuMLP3w
ZqoAmwZErUyIkfr00w9KyOgLxnYefTJ6
=q2zn
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.1' of git://git.infradead.org/linux-mvebu into next/soc
Pull "mvebu soc changes for v4.1 (part #1)" from Gregory CLEMENT:
- Add support for a new SoC: Armada 39x
* tag 'mvebu-soc-4.1' of git://git.infradead.org/linux-mvebu:
Documentation: arm: update supported Marvell EBU processors
ARM: mvebu: add core support for Armada 39x
devicetree: bindings: add new SMP enable method for Marvell Armada 39x
devicetree: bindings: add DT binding for the Marvell Armada 39x SoC family
- add the new Armada 39x SoC in mvebu_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9R2MACgkQCwYYjhRyO9UOLQCfeQuNL/nHDlc+0GanS9pBAyil
sBMAoKGEjhdA1NTfnykWexg3Ml4BwVX4
=VaQQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig-4.1' of git://git.infradead.org/linux-mvebu into next/defconfig
Pull "mvebu defconfig changes for v4.1 (part #1)" from Gregory CLEMENT:
- add the new Armada 39x SoC in mvebu_v7_defconfig
* tag 'mvebu-defconfig-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: enable Armada 39x in mvebu_v7_defconfig
- Constify the dt_compat table in DT_MACHINE_START
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9Re4ACgkQCwYYjhRyO9WLaQCfeTz2auqoPt5vXTJjs9/sXLEL
dQIAnjPIpZfLVBnNo1BzK96RUYHEJ20+
=QIYe
-----END PGP SIGNATURE-----
Merge tag 'mvebu-cleanup-4.1' of git://git.infradead.org/linux-mvebu into next/cleanup
Pull "mvebu clean-up changes for v4.1 (part #1)" from Gregory CLEMENT:
- Constify the dt_compat table in DT_MACHINE_START
* tag 'mvebu-cleanup-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add __initconst specifiers on DT_MACHINE_START dt_compat tables
Adds support for Spreadtrum's SoC Platform in the arm64 Kconfig and
defconfig files.
Signed-off-by: Zhizhou Zhang <zhizhou.zhang@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Adds the device tree support for Spreadtrum SC9836 SoC which is based on
Sharkl64 platform.
Sharkl64 platform contains the common nodes of Spreadtrum's arm64-based SoCs.
Signed-off-by: Zhizhou Zhang <zhizhou.zhang@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Initial version of device tree for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Florian Fainelli says:
====================
net: dsa: support PHY reads/writes diversion
This patch series completes the PHY reads/writes diversion when we need to use
the slave MII bus provided by DSA and the underlying switch drivers to
implement the real PHY reads and writes. This is particularly useful when they
are conflicting MDIO bus addresses as in the case of multiple Broadcom switches
connected to each other (internal and external, or just external).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.
Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for dealing with indirect reads and writes towards
certain PHY devices, move the code which deals with binding the PHY
device to the slave MII bus created by DSA to its own function:
dsa_slave_phy_connect().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export of_mdio_parse_addr() which allows parsing a given Ethernet PHY
node MDIO address, verify it is within the allowed range, and return
its value. This is going to be useful for the DSA code which needs to
deal with multiple layers of MDIO buses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9S+0ACgkQCwYYjhRyO9XSkQCfcrsiF6bS+B1B9Gdu+nBwyXdC
BHYAmwUm92D7yH8ePjbKldM4ONM1315b
=yn/6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
The watchdog clock should be disable in dw_wdt_suspend, but we set a
dummy clock to watchdog for rk3288. So the watchdog will continue to
work during suspend. And we switch the system clock to 32khz from 24Mhz,
during suspend, so the watchdog timer over count will increase to
755 times, about 12.5 hours, the original value is 60 seconds. So
watchdog will reset the system over a night, but voltage are all
incorrect, then it hang on reset.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The register-default delay time for wait the 24MHz OSC stabilization as well
as PMU stabilization is 750ms, let's decrease them to a still safe 30ms.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Make function rockchip_get_core_reset() static because it is not used
outside of the platsmp.c file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 0-day kernel test infrastructure reported a use of uninitialized
variable warning for local_table due to the fact that the local and main
allocations had been swapped from the original setup. This change corrects
that by making it so that we free the main table if the local table
allocation fails.
Fixes: 0ddcf43d5 ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want tile 0,0 to artificially constrain the size of the legacy
fbdev device. Instead when reducing fb_size to be the minimum of all
displays, only consider the rightmost and bottommost tiles.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Hai Li <hali@codeaurora.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Flip conditional to reduce indentation level of rest of fxn, and use
min/max to make the code clearer.
v2: surface_width -> surface_height typo
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There has been some confusion about this struct. Lack of documentation
probably didn't help.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Older DisplayPort to DVI-D Dual Link adapters designed by Bizlink have bugs
in their I2C over AUX implementation (fixed in newer revisions). They work
fine with Windows, but fail with Linux.
It turns out that they cannot keep an I2C transaction open unless the
previous read was 16 bytes; shorter reads can only be followed by a zero
byte transfer ending the I2C transaction.
Copy Windows's behaviour, and read 16 bytes at a time. If we get a short
reply, assume that there's a hardware bottleneck, and shrink our read size
to match. For this purpose, use the algorithm in the DisplayPort 1.2 spec,
in the hopes that it'll be closest to what Windows does.
Also provide an unsafe module parameter for testing smaller transfer sizes,
in case there are sinks out there that cannot work with Windows.
Note also that despite the previous comment in drm_dp_i2c_xfer, this speeds
up native DP EDID reads; Ville Syrjälä <ville.syrjala@linux.intel.com> found
the following changes in his testing:
Device under test: old -> with this patch
DP->DVI (OUI 001cf8): 40ms -> 35ms
DP->VGA (OUI 0022b9): 45ms -> 38ms
Zotac DP->2xHDMI: 25ms -> 4ms
Asus PB278 monitor: 22ms -> 3ms
A back of the envelope calculation shows that peak theoretical transfer rate
for 1 byte reads is around 60 kbit/s; with 16 byte reads, this increases to
around 500 kbit/s, which explains the increase in speed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55228
Tested-by: Aidan Marks <aidanamarks@gmail.com> (v3)
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 5c1de006e8.
While the original commit makes it easier to run cpupower from the
local build directory, it also leaves the binary with a rather poor
rpath of './' in it after it is installed on a system via 'make install'.
This is considered bad practice and can cause cpupower to fail in
rpmbuild with the following error:
ERROR 0004: file '/usr/bin/cpupower' contains an insecure rpath './' in [./]
error: Bad exit status from /var/tmp/rpm-tmp.A6u26r (%install)
Bad exit status from /var/tmp/rpm-tmp.A6u26r (%install)
Developers should be able to use LD_LIBRARY_PATH to achieve the same
effect and not introduce rpath into the binary.
Signed-off-by: Josh Boyer <jwboyer@feoraproject.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 814d488c61 ("tcp: fix the timid additive increase on stretch
ACKs") fixed a bug where tcp_cong_avoid_ai() would either credit a
connection with an increase of snd_cwnd_cnt, or increase snd_cwnd, but
not both, resulting in cwnd increasing by 1 packet on at most every
alternate invocation of tcp_cong_avoid_ai().
Although the commit correctly implemented the CUBIC algorithm, which
can increase cwnd by as much as 1 packet per 1 packet ACKed (2x per
RTT), in practice that could be too aggressive: in tests on network
paths with small buffers, YouTube server retransmission rates nearly
doubled.
This commit restores CUBIC to a maximum cwnd growth rate of 1 packet
per 2 packets ACKed (1.5x per RTT). In YouTube tests this restored
retransmit rates to low levels.
Testing: This patch has been tested in datacenter netperf transfers
and live youtube.com and google.com servers.
Fixes: 9cd981dcf1 ("tcp: fix stretch ACK bugs in CUBIC")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent change to tcp_cong_avoid_ai() to handle stretch ACKs
introduced a bug where snd_cwnd_cnt could accumulate a very large
value while w was large, and then if w was reduced snd_cwnd could be
incremented by a large delta, leading to a large burst and high packet
loss. This was tickled when CUBIC's bictcp_update() sets "ca->cnt =
100 * cwnd".
This bug crept in while preparing the upstream version of
814d488c61.
Testing: This patch has been tested in datacenter netperf transfers
and live youtube.com and google.com servers.
Fixes: 814d488c61 ("tcp: fix the timid additive increase on stretch ACKs")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed to my private email address.
Signed-off-by: Chas Williams -- CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rtnl_lock() before the call to fib4_rules_exit so that
fib_table_flush_external is called under RTNL.
Fixes: 104616e74e ("switchdev: don't support custom ip rules, for now")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_MPLS=m doesn't result in a kernel module being built because it
applies to the net/mpls directory, rather than to .o files.
So revert the MPLS menuitem to being a boolean and make MPLS_GSO and
MPLS_ROUTING tristates to allow mpls_gso and mpls_router modules to be
produced as desired.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FSL_PQ_MDIO and FSL_XGMAC_MDIO are not really depend on FSL_SOC, they
can build on non-PPC platforms.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a rehash function that supports the use of any
hash function for the new table. This is needed to support changing
the random seed value during the lifetime of the hash table.
However for now the random seed value is still constant and the
rehash function is simply used to replace the existing expand/shrink
functions.
[ ASSERT_BUCKET_LOCK() and thus debug_dump_table() +
debug_dump_buckets() are not longer used, so delete them
entirely. -DaveM ]
Signed-off-by: Herbert Xu <herbert.xu@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hash_rnd is a parameter that users can set. However,
no existing users set this parameter. It is also something that
people are unlikely to want to set directly since it's just a
random number.
In preparation for allowing the reseeding/rehashing of rhashtable,
this patch moves hash_rnd into bucket_table so that it's now an
internal state rather than a parameter.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Qualcomm MSM8916 SoC in arm64 Kconfig and defconfig.
Enable MSM8916 clock, pin control, and MSM serial driver utilized by
MSM8916 and Qualcomm SoCs in general.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Abhimanyu Kapur <abhimany@codeaurora.org>
Offline CPUs cannot safely invoke trace events, but such CPUs do execute
within rcu_cpu_notify(). Therefore, this commit removes the trace events
from rcu_cpu_notify(). These trace events are for utilization, against
which rcu_cpu_notify() execution time should be negligible.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit sets CONFIG_RCU_TORTURE_TEST_SLOW_INIT=y, but leaves the
default time zero. This can be overridden by passing the
"--bootargs rcutree.gp_init_delay=1" argument to kvm.sh.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Grace-period initialization normally proceeds quite quickly, so
that it is very difficult to reproduce races against grace-period
initialization. This commit therefore allows grace-period
initialization to be artificially slowed down, increasing
race-reproduction probability. A pair of new Kconfig parameters are
provided, CONFIG_RCU_TORTURE_TEST_SLOW_INIT to enable the slowdowns, and
CONFIG_RCU_TORTURE_TEST_SLOW_INIT_DELAY to specify the number of jiffies
of slowdown to apply. A boot-time parameter named rcutree.gp_init_delay
allows boot-time delay to be specified. By default, no delay will be
applied even if CONFIG_RCU_TORTURE_TEST_SLOW_INIT is set.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If all CPUs have passed through quiescent states, then stalls might be
due to starvation of the grace-period kthread or to failure to propagate
the quiescent states up the rcu_node combining tree. The current stall
warning messages do not differentiate, so this commit adds a printout
of the root rcu_node structure's ->qsmask field.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, both rcu_cleanup_dead_cpu() and rcu_send_cbs_to_orphanage()
initialize the outgoing CPU's callback list. However, only
rcu_cleanup_dead_cpu() invokes rcu_send_cbs_to_orphanage(), and
it does so unconditionally, which means that only one of these
initializations is required. This commit therefore consolidates the
callback-list initialization with the rest of the callback handling in
rcu_send_cbs_to_orphanage().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit removes the open-coded CPU-offline notification with new
common code. This change avoids calling scheduler code using RCU from
an offline CPU that RCU is ignoring. This commit is compatible with
the existing code in not checking for timeout during a prior offline
for a given CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <linux-metag@vger.kernel.org>
This commit removes the open-coded CPU-offline notification with new
common code. This change avoids calling scheduler code using RCU from
an offline CPU that RCU is ignoring. This commit is compatible with
the existing code in not checking for timeout during a prior offline
for a given CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: <adi-buildroot-devel@lists.sourceforge.net>
This commit removes the open-coded CPU-offline notification with new
common code. Among other things, this change avoids calling scheduler
code using RCU from an offline CPU that RCU is ignoring. It also allows
Xen to notice at online time that the CPU did not go offline correctly.
Note that Xen has the surviving CPU carry out some cleanup operations,
so if the surviving CPU times out, these cleanup operations might have
been carried out while the outgoing CPU was still running. It might
therefore be unwise to bring this CPU back online, and this commit
avoids doing so.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: <x86@kernel.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: <xen-devel@lists.xenproject.org>
