To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.
rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
update card drive settings, This setting can be used for rts5249
rts524A and rts525A.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is more readable to place register address and values define
togather. The values define add two leading space indicate belong
to the register address defined above.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Re-format coding-style, using uniform SPC after "#define" keyword
instead of mixing using TAB and SPC.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Surely GPIO irq will be used as an input pin so make sure its direction is
set after requesting.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is usually better to pass actual error code from a function call than
mangling it to another.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
intel_soc_pmic_find_gpio_irq() tries to find a GPIO interrupt but doesn't
select between it or I2C interrupt so it makes more sense to move this
comment to intel_soc_pmic_i2c_probe() with minor edits.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Or c6x will cause building break for allmodconfig, the related error:
CC arch/c6x/kernel/setup.o
arch/c6x/kernel/setup.c: In function 'setup_arch':
arch/c6x/kernel/setup.c:433:2: error: 'conswitchp' undeclared (first use in this function)
conswitchp = &dummy_con;
^
arch/c6x/kernel/setup.c:433:2: note: each undeclared identifier is reported only once for each function it appears in
arch/c6x/kernel/setup.c:433:16: error: 'dummy_con' undeclared (first use in this function)
conswitchp = &dummy_con;
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
[removed unnecessary #ifdef around include]
Signed-off-by: Mark Salter <msalter@redhat.com>
1) We can safely use the function's 'i'. Fixes warning
fs/btrfs/volumes.c:5257:7: warning: declaration of 'i' shadows a previous local
fs/btrfs/volumes.c:4951:6: warning: shadowed declaration is here
2) A local variable duplicates name of an argument, we can use the value
directly. Fixes warning
fs/btrfs/volumes.c:5433:8: warning: declaration of 'length' shadows a parameter
fs/btrfs/volumes.c:4935:27: warning: shadowed declaration is here
Signed-off-by: David Sterba <dsterba@suse.cz>
The conversion macros use nested container_of that leads to a warning
fs/btrfs/sysfs.c: In function 'btrfs_feature_visible':
fs/btrfs/sysfs.c:183:8: warning: declaration of '__mptr' shadows a previous local
fs/btrfs/sysfs.c:183:8: warning: shadowed declaration is here
Use of functions will add proper type checking.
Signed-off-by: David Sterba <dsterba@suse.cz>
The divisor is derived from nodesize or PAGE_SIZE, fits into 32bit type.
Get rid of a few more do_div instances.
Signed-off-by: David Sterba <dsterba@suse.cz>
Using {} as initializer for struct seq_elem does not properly initialize
the list_head member, but it currently works because it gets set through
btrfs_get_tree_mod_seq if 'seq' is 0.
Signed-off-by: David Sterba <dsterba@suse.cz>
There are lockstart and lockend defined in the function and not used
after their duplicate definition scope ends, it's safe to reuse them.
Signed-off-by: David Sterba <dsterba@suse.cz>
Convert kmalloc(nr * size, ..) to kmalloc_array that does additional
overflow checks, the zeroing variant is kcalloc.
Signed-off-by: David Sterba <dsterba@suse.cz>
Switch to div_u64 if the divisor is a numeric constant or sum of
sizeof()s. We can remove a few instances of do_div that has the hidden
semtantics of changing the 1st argument.
Small power-of-two divisors are converted to bitshifts, large values are
kept intact for clarity.
Signed-off-by: David Sterba <dsterba@suse.cz>
Clean the opencoded variant, cond_resched_lock also checks the lock for
contention so it might help in some cases that were not covered by
simple need_resched().
Signed-off-by: David Sterba <dsterba@suse.cz>
The divisor is derived from nodesize or PAGE_SIZE, fits into 32bit type.
Get rid of a few more do_div instances.
Signed-off-by: David Sterba <dsterba@suse.cz>
Add xtal as a configuration parameter so it can be used
in the IF register value calculation. If not set in the
configuration then use a default value.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: Alan Fisher <acf@unixcube.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was incorrectly detected as 2 GHz device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If any interface fails to be added to the driver in during reconfig,
we should remove all the successfully added interfaces and report
reconfig failure, so things can be cleaned up properly. Failing to do
so can lead to subsequent failures and leave the drivers in a messed
up state.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 disconnects, but has no insight into the association
process, it can happen that it disconnects while association is in
progress. We then try to abort association in mac80211, but this is
only later so the association can complete between the two.
This results in removing an interface from the driver while bound
to the channel context, obviously causing confusion and issues.
Solve this by also checking if we're associated during quiesce and
if so deauthenticating. The frame will no longer go out to the AP
which is a bit unfortunate, but it'll resolve the crash (and before
we would have suspended without telling the AP as well.)
I'm working on a better, but more complex solution as well, which
should avoid that problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the AID and VHT-cap/operation IEs during TDLS setup. Remove the
block of TDLS peers when setting HT-caps of the peer station.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Operating classes 128-130 are defined in the 11ac
spec for the 5GHz band.
Update ieee80211_operating_class_to_band() to support them.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon's timestamp, device system time associated with this beacon and
DTIM count parameters are not updated in the associated vif context
if the latest beacon's content is identical to the previously received.
It make sense to update these changing parameters on every beacon so the
driver can get most updated values. This may be necessary, for example,
to avoid either beacons' drift effect or device time stamp overrun.
IMPORTANT: Three sync_* parameters - sync_ts, sync_device_ts and
sync_dtim_count would possibly be out of sync by the time the driver will
use them. The synchronized view is currently guaranteed only in certain
callbacks.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add notes about userspace ABI/API modifications, including the
fact that we decided that API submissions should come with a
driver implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows wpa_supplicant/hostapd to send a vendor command and verify
response to that command and a vendor event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This modifies cfg80211_vendor_event_alloc() with an additional argument
struct wireless_dev *wdev. __cfg80211_alloc_event_skb() is modified to
take in *wdev argument, if wdev != NULL, both the NL80211_ATTR_IFINDEX
and wdev identifier are added to the vendor event.
These changes make it easier for drivers to add ifindex indication in
vendor events cleanly.
This also updates all existing users of cfg80211_vendor_event_alloc()
and __cfg80211_alloc_event_skb() in the kernel tree.
Signed-off-by: Ahmad Kholaif <akholaif@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_EXT_FEATURE_VHT_IBSS flag and VHT
support for IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removing the udelay between setting and clearing the soft reset bit in
the spfi control register as it is not required.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify accordingly.
Moreover use devm_gpiod_get_index_optional instead of
devm_gpiod_get_index with ignoring all errors.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Maximum transfer length supported by SPFI is 65535, this is limited
by the number of bits available in SPFI TSize register to represent
the transfer size.
For transfer requests larger than the maximum supported the driver
will return an invalid argument error.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current GStreamer userspace respects the bytes_per_line from the driver. Set
it to something reasonable for the format chosen.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
the declaration for omap_vout_setup_vrfb_bufs() said it
needed 'u32 static_vrfb_allocation' but definition
took 'bool static_vrfb_allocation', this patch fixes the
declaration so that it matches with the definition and
pass a bool instead of int to the call, also included
omap_vout_vrfb.h in omap_vout_vrfb.c file so that sparse doesn't
complain of making omap_vout_setup_vrfb_bufs() as static function.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
