libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thu, 1 Feb 2007, Andrew Morton wrote:
> On Thu, 1 Feb 2007 15:34:29 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7919
> >
> > Summary: Tape dies if wrong block size used
> > Kernel Version: 2.6.20-rc5
> > Status: NEW
> > Severity: normal
> > Owner: scsi_drivers-other@kernel-bugs.osdl.org
> > Submitter: dmartin@sccd.ctc.edu
> >
> >
> > Most recent kernel where this bug did *NOT* occur: 2.6.17.14
> >
> > Other Kernels Tested and Results:
> >
> > OK 2.6.15.7
> > OK 2.6.16.37
> > OK 2.6.17.14
> > BAD 2.6.18.6
> > BAD 2.6.18-1.2869.fc6
> > BAD 2.6.19.2 +
> > BAD 2.6.20-rc5
> >
> > NOTE: 2.6.18-1.2869.fc6 is a Fedora modified kernel, all others are from kernel.org
> >
...
> > Steps to reproduce:
> > Get a Adaptec AHA-2940U/UW/D / AIC-7881U card and a tape drive,
> > install a recent kernel
> > set the tape block size - mt setblk 4096
> > read from or write to tape using wrong block size - tar -b 7 -cvf /dev/tape foo
> >
Write does not trigger this bug because the driver refuses in fixed block
mode writes that are not a multiple of the block size. Read does trigger
it in my system.
The bug is not associated with any specific HBA. st tries to do direct i/o
in fixed block mode with reads that are not a multiple of tape block size.
The patch in this message fixes the st problem by switching to using the
driver buffer up to the next close of the device file in fixed block mode
if the user asks for a read like this.
I don't know why the bug has surfaced only after 2.6.17 although the st
problem is old. There may be another bug in the block subsystem and this
patch works around it. However, the patch fixes a problem in st and in
this way it is a valid fix.
This patch may also fix the bug 7900.
The patch compiles and is lightly tested.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set fake hid for ejectable drive bay.
Match bay devices by checking the hid.
Remove .match method of Bay driver.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert the bay driver to be a platform driver, so that we can have
sysfs entries.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove all the procfs related code.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When determining if a device is on a dock station, we should
check the parent of the device as well.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/namespace/nsparse.c:126: warning: int format, different type arg (arg 7)
drivers/acpi/tables/tbfadt.c:224: warning: unsigned int format, different type arg (arg 6)
drivers/acpi/utilities/utdebug.c:184: warning: cast from pointer to integer of different size
drivers/acpi/utilities/utdebug.c:184: warning: cast from pointer to integer of different size
drivers/acpi/utilities/utdebug.c:197: warning: cast from pointer to integer of different size
drivers/acpi/processor_idle.c:1093: warning: long long unsigned int format, u64 arg (arg 5)
Signed-off-by: Len Brown <len.brown@intel.com>
Fix this by letting NF_CONNTRACK_H323 depend on (IPV6 || IPV6=n).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for dynamic loading and unloading of ACPI SSDT tables upon slot
hotplugs and unplugs.
On SN platforms, we now represent every populated root bus slot with a single
ACPI SSDT table containing info for every device and PPB attached to the slot.
These SSDTs are generated by the prom at initial boot and hotplug time. The
info in these SSDT tables is used by the SN kernel IO "fixup" code (which is
called at boot and hotplug time).
On hotplugs (i.e. enable_slot()), if running with an ACPI capable prom,
attempt to obtain a new ACPI SSDT table for the slot being hotplugged. If
successful, add the table to the ACPI namespace (acpi_load_table()) and then
walk the new devices and add them to the ACPI infrastructure (acpi_bus_add()).
On hot unplugs (i.e. disable_slot()), if running with an ACPI capable prom,
attempt to remove the SSDT table associated with the slot from the ACPI
namespace (acpi_unload_table_id()) and infastructure (acpi_bus_trim()).
From: John Keller <jpk@sgi.com>
A bug was fixed where the sgi hotplug driver was removing
the slot's SSDT table from the ACPI namespace a bit too early in
disable_slot(). Also, we now call acpi_bus_start() subsequent
to acpi_bus_add().
Signed-off-by: Aaron Young <ayoung@sgi.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown<len.brown@intel.com>
Add SN platform support for running with an ACPI
capable PROM that defines PCI devices in SSDT
tables. There is a SSDT table for every occupied
slot on a root bus, containing info for every
PPB and/or device on the bus. The SSDTs will be
dynamically loaded/unloaded at hotplug enable/disable.
Platform specific information that is currently
passed via a SAL call, will now be passed via the
Vendor resource in the ACPI Device object(s) defined
in each SSDT.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
bump version, and fix email addr for lsi support
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
misc error handling bug fix's
- properly interpret iocstatus returned after task management request
- clear tmState after a failed doorbell
- cleanup mptscsih_taskmgmt_complete
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return proper sas address to sas transport layer for parent phys that
form a wide port. Current implementation returns a different address
for each phy, incremented by one from the base address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ACPI 3.0 incorporated the SRAT spec, upping the table version to 2,
and extending the size of the proximity domain from 1-byte to 4-bytes.
This extension was into a reserved field that firmware should
set to 0, but the HP simulator had non-zero values there
resulting in unexpected huge numbers.
So mask the domain down to 8-bits for now.
A more general fix will be to check the table version
supplied by firmware and get paranoid about reserved fields.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fusion firmware requires target reset following hotplug removal event,
with purpose to flush target outstanding request in fw. Current implementation
does the target resets from delayed work tasks, that in heavy load
conditions, take too long to be invoked, resulting in command time outs
This patch will issue target reset immediately from ISR context, and will
queue remaining target resets to be issued after the previous one completes.
The delayed work tasks are spawned during the target reset completion.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
inactive raid support, e.g. exposing hidden raid components
belonging to a volume that are inactive. Also misc bug fix's for
various raid asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
various string updates for iocstatus, logingo, and fw asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move some functions that only apply to the mptspi module over from mptscsih.c
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for greater than 255 target and luns.
Kill the hd->Target[] field, and change all references
of bus_id/target_id, to channel/id.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Copy space_id of GAS structure to newly created GAS.
The previous FADT conversion code defaulted to IO space.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
i386 srat.c broke due to re-names from ACPICA table-manager re-write.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bad pointer was passed in the case where the DSDT is overridden.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added 2007 copyright to all module headers and signons. This affects
virtually every file in the ACPICA core subsystem, iASL compiler,
and the utilities.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow processor to be declered with the Device(), such as:
Device(CPU1234) {
Name(_HID, "ACPI007")
Name(_UID, 1234)
}
Signed-off-by: Len Brown <len.brown@intel.com>
Debugger: Enhanced the Statistics/Memory command to emit the
total (maximum) memory used during execution, as well as the
maximum memory consumed by each of the various object types.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented enhancements to the multithreading support within
the debugger to enable better multithreading evaluation of the subsystem.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>