Commit graph

3,837 commits

Author SHA1 Message Date
Horatiu Vultur
b3f1a08fcf net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
On lan8814 only GPIO 3 can be configured for this.

This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg

Where the configuration was the following:
    ---
    [global]
    ts2phc.pin_index  3

    [eth0]
    ---

Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-29 13:37:19 +01:00
Daniel Golle
0805d67bc0 net: sfp: add quirk for ATS SFP-GE-T 1000Base-TX module
Add quirk for ATS SFP-GE-T 1000Base-TX module.

This copper module comes with broken TX_FAULT indicator which must be
ignored for it to work.

Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[ rebased on top of net-next ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240423090025.29231-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25 18:42:07 -07:00
Marek Behún
cd4a32e600 net: sfp: enhance quirk for Fibrestore 2.5G copper SFP module
Enhance the quirk for Fibrestore 2.5G copper SFP module. The original
commit e27aca3760 ("net: sfp: add quirk for FS's 2.5G copper SFP")
introducing the quirk says that the PHY is inaccessible, but that is
not true.

The module uses Rollball protocol to talk to the PHY, and needs a 4
second wait before probing it, same as FS 10G module.

The PHY inside the module is Realtek RTL8221B-VB-CG PHY. The realtek
driver recently gained support to set it up via clause 45 accesses.

Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240423085039.26957-2-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25 18:40:56 -07:00
Marek Behún
6999e0fc9a net: sfp: update comment for FS SFP-10G-T quirk
Update the comment for the Fibrestore SFP-10G-T module: since commit
e9301af385 ("net: sfp: fix PHY discovery for FS SFP-10G-T module")
we also do a 4 second wait before probing the PHY.

Fixes: e9301af385 ("net: sfp: fix PHY discovery for FS SFP-10G-T module")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240423085039.26957-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25 18:40:56 -07:00
Jakub Kicinski
2bd87951de Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR.

Conflicts:

drivers/net/ethernet/ti/icssg/icssg_prueth.c

net/mac80211/chan.c
  89884459a0 ("wifi: mac80211: fix idle calculation with multi-link")
  87f5500285 ("wifi: mac80211: simplify ieee80211_assign_link_chanctx()")
https://lore.kernel.org/all/20240422105623.7b1fbda2@canb.auug.org.au/

net/unix/garbage.c
  1971d13ffa ("af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc().")
  4090fa373f ("af_unix: Replace garbage collection algorithm.")

drivers/net/ethernet/ti/icssg/icssg_prueth.c
drivers/net/ethernet/ti/icssg/icssg_common.c
  4dcd0e83ea ("net: ti: icssg-prueth: Fix signedness bug in prueth_init_rx_chns()")
  e2dc7bfd67 ("net: ti: icssg-prueth: Move common functions into a separate file")

No adjacent changes.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25 12:41:37 -07:00
MD Danish Anwar
6c9cd59dbc net: phy: dp83869: Fix MII mode failure
The DP83869 driver sets the MII bit (needed for PHY to work in MII mode)
only if the op-mode is either DP83869_100M_MEDIA_CONVERT or
DP83869_RGMII_100_BASE.

Some drivers i.e. ICSSG support MII mode with op-mode as
DP83869_RGMII_COPPER_ETHERNET for which the MII bit is not set in dp83869
driver. As a result MII mode on ICSSG doesn't work and below log is seen.

TI DP83869 300b2400.mdio:0f: selected op-mode is not valid with MII mode
icssg-prueth icssg1-eth: couldn't connect to phy ethernet-phy@0
icssg-prueth icssg1-eth: can't phy connect port MII0

Fix this by setting MII bit for DP83869_RGMII_COPPER_ETHERNET op-mode as
well.

Fixes: 94e86ef1b8 ("net: phy: dp83869: support mii mode when rgmii strap cfg is used")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-25 11:25:07 +01:00
Daniel Golle
5b5f724b05 net: phy: mediatek-ge-soc: follow netdev LED trigger semantics
Only blink if the link is up on a LED which is programmed to also
indicate link-status.

Otherwise, if both LEDs are in use to indicate different speeds, the
resulting blinking being inverted on LEDs which aren't switched on at
a specific speed is quite counter-intuitive.

Also make sure that state left behind by reset or the bootloader is
recognized correctly including the half-duplex and full-duplex bits as
well as the (unsupported by Linux netdev trigger semantics) link-down
bit.

Fixes: c66937b0f8 ("net: phy: mediatek-ge-soc: support PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-24 11:50:49 +01:00
Arınç ÜNAL
af3b4b0e59 net: phy: mediatek-ge: do not disable EEE advertisement
The mediatek-ge PHY driver already disables EEE advertisement on the switch
PHYs but my testing [1] shows that it is somehow enabled afterwards.
Disabling EEE advertisement before the PHY driver initialises keeps it off.
Therefore, remove disabling EEE advertisement here as it's useless.

Link: https://lore.kernel.org/netdev/d286ea27-e911-4dcb-9037-b75f22b437b8@arinc9.com/ [1]
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-17 10:44:20 +01:00
Marek Behún
1c77c72191 net: sfp: add quirk for another multigig RollBall transceiver
Add quirk for another RollBall copper transceiver: Turris RTSFP-2.5G,
containing 2.5g capable RTL8221B PHY.

Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:18 +01:00
Eric Woudstra
2d9ce64862 net: phy: realtek: add rtl822x_c45_get_features() to set supported port
Sets ETHTOOL_LINK_MODE_TP_BIT in phydev->supported.

Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:18 +01:00
Eric Woudstra
2e4ea707c7 net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()
The value of the register to determine the speed, is retrieved
differently when using Clause 45 only. To use the rtlgen_get_speed()
function in this case, pass the value of the register as argument to
rtlgen_get_speed(). The function would then always return 0, so change it
to void. A better name for this function now is rtlgen_decode_speed().

Replace a call to genphy_read_status() followed by rtlgen_get_speed()
with a call to rtlgen_read_status() in rtl822x_read_status().

Add reading speed to rtl822x_c45_read_status().

Signed-off-by: Eric Woudstra <ericwouds@gmail.com>

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:18 +01:00
Marek Behún
ad5ce743a6 net: phy: realtek: Add driver instances for rtl8221b via Clause 45
Collected from several commits in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"

The instances are used by Clause 45 only accessible PHY's on several sfp
modules, which are using RollBall protocol.

Signed-off-by: Marek Behún <kabel@kernel.org>
[ Added matching functions to differentiate C45 instances ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:18 +01:00
Eric Woudstra
c189dbd738 net: phy: realtek: add get_rate_matching() for rtl822xb PHYs
Uses vendor register to determine if SerDes is setup in rate-matching mode.

Rate-matching only supported when SerDes is set to 2500base-x.

Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:18 +01:00
Alexander Couzens
deb8af5243 net: phy: realtek: configure SerDes mode for rtl822xb PHYs
The rtl8221b and rtl8226b series support switching SerDes mode between
2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by
host.

There is an additional datasheet for RTL8226B/RTL8221B called
"SERDES MODE SETTING FLOW APPLICATION NOTE" where a sequence is
described to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers
and bits, it's literally just magic numbers and pseudo-code.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ refactored, dropped HiSGMII mode and changed commit message ]
Signed-off-by: Marek Behún <kabel@kernel.org>
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
[ only apply to rtl8221b and rtl8226b phy's ]
[ set phydev->rate_matching in .config_init() ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: should come before them, without any blank lines. As the
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-12 10:18:17 +01:00
Catalin Popescu
9ef9ecfa9e net: phy: dp8382x: keep WOL settings across suspends
Unlike other ethernet PHYs from TI, PHY dp8382x has WOL enabled
at reset. The driver explicitly disables WOL in config_init callback
which is called during init and during resume from suspend. Hence,
WOL is unconditionally disabled during resume, even if it was enabled
before the suspend. We make sure that WOL configuration is persistent
across suspends.

Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240408082602.3654090-1-catalin.popescu@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-09 16:57:55 -07:00
Horatiu Vultur
9e63941b89 net: phy: micrel: lan8814: Add support for PTP_PF_PEROUT
Lan8814 has 24 GPIOs but only 2 GPIOs (GPIO 0 and GPIO 1) can be
configured to generate period signals. And there are 2 events (EVENT_A
and EVENT_B) but these events are hardcoded to the GPIO 0 and GPIO 1.
These events are used to generate period signals. It is possible to
configure the length, the start time and the period of the signal by
configuring the event.

These events are generated by comparing the target time with the PHC
time. In case the PHC time is changed to a value bigger than the target
time + reload time, then it would generate only 1 event and then it
would stop because target time + reload time is smaller than PHC time.
Therefore it is required to change also the target time every time when
the PHC is changed. The same will apply also when the PHC time is
changed to a smaller value.

This was tested using:
testptp -i 1 -L 1,2
testptp -i 1 -p 1000000000 -w 200000000

Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-04-09 13:34:03 +02:00
Horatiu Vultur
9f6b3a4981 net: phy: micrel: lan8814: Enable LTC at probe time
The LTC for lan8814 was enabled only if timestamping was enabled,
otherwise it would be stopped. Meaning that LTC will not increase by
itself. This might break other features that don't required timestamping
like generating 1PPS. Therefore enable the LTC at probe time.

Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-04-09 13:34:03 +02:00
Dan Carpenter
87c33315af net: phy: air_en8811h: fix some error codes
These error paths accidentally return "ret" which is zero/success
instead of the correct error code.

Fixes: 71e7943011 ("net: phy: air_en8811h: Add the Airoha EN8811H PHY driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/7ef2e230-dfb7-4a77-8973-9e5be1a99fc2@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-08 19:46:16 -07:00
Maxime Chevallier
fdd353965b net: sfp: Add helper to return the SFP bus name
Knowing the bus name is helpful when we want to expose the link topology
to userspace, add a helper to return the SFP bus name.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-06 18:25:14 +01:00
Maxime Chevallier
e75e4e074c net: phy: add helpers to handle sfp phy connect/disconnect
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.

By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-06 18:25:14 +01:00
Maxime Chevallier
0ec5ed6c13 net: sfp: pass the phy_device when disconnecting an sfp module's PHY
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-06 18:25:14 +01:00
Maxime Chevallier
6916e461e7 net: phy: Introduce ethernet link topology representation
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.

With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.

The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.

Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.

The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.

This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.

The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-06 18:25:14 +01:00
Pawel Dembicki
d133ef1ee2 net: phy: marvell: implement cable test for 88E1111
The same implementation is also valid for 88E1145. VCT in 88E1111 is
similar to the 88E609x family. The main difference lies in register
organization and required workarounds.

It utilizes the same fields in registers but requires a simpler
implementation.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-06 18:21:53 +01:00
Jakub Kicinski
cf1ca1f66d Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR.

Conflicts:

net/ipv4/ip_gre.c
  17af420545 ("erspan: make sure erspan_base_hdr is present in skb->head")
  5832c4a77d ("ip_tunnel: convert __be16 tunnel flags to bitmaps")
https://lore.kernel.org/all/20240402103253.3b54a1cf@canb.auug.org.au/

Adjacent changes:

net/ipv6/ip6_fib.c
  d21d40605b ("ipv6: Fix infinite recursion in fib6_dump_done().")
  5fc68320c1 ("ipv6: remove RTNL protection from inet6_dump_fib()")

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-04 18:01:07 -07:00
Pawel Dembicki
a9e4230d0b net: phy: marvell: implement cable-test for 88E308X/88E609X family
This commit implements VCT in 88E308X/88E609X Family.

It require two workarounds with some magic configuration.
Regular use require only one register configuration. But Open Circuit
require second workaround.
It cause implementation two phases for fault length measuring.

Fast Ethernet PHY have implemented very simple version of VCT. It's
complitley different than vct5 or vct7.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240402201123.2961909-3-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-03 19:33:20 -07:00
Pawel Dembicki
ada9841e3e net: phy: marvell: add basic support of 88E308X/88E609X family
This patch implements only basic support.

It covers PHY used in multiple IC:
PHY: 88E3082, 88E3083
Switch: 88E6096, 88E6097

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240402201123.2961909-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-03 19:33:20 -07:00
Horatiu Vultur
de99e1ea3a net: phy: micrel: lan8814: Fix when enabling/disabling 1-step timestamping
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
   checksums. The UDPv6 checksum is already enabled by default. So when
   1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
   1-step would be still configured because it is not clearing the flag.
   So the sync frames will still have origin timestamps set.

Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.

Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-03 19:23:17 -07:00
Paweł Owoc
c278ec6443 net: phy: aquantia: add support for AQR114C PHY ID
Add support for AQR114C PHY ID. This PHY advertise 10G speed:
SPEED(0x04): 0x6031
  capabilities: -400g +5g +2.5g -200g -25g -10g-xr -100g -40g -10g/1g -10
                +100 +1000 -10-ts -2-tl +10g
EXTABLE(0x0B): 0x40fc
  capabilities: -10g-cx4 -10g-lrm +10g-t +10g-kx4 +10g-kr +1000-t +1000-kx
                +100-tx -10-t -p2mp -40g/100g -1000/100-t1 -25g -200g/400g
                +2.5g/5g -1000-h

but supports only up to 5G speed (as with AQR111/111B0).
AQR111 init config is used to set max speed 5G.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240401145114.1699451-1-frut3k7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-02 17:46:28 -07:00
Aleksandr Mishin
96c155943a net: phy: micrel: Fix potential null pointer dereference
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-01 20:41:49 -07:00
Eric Woudstra
71e7943011 net: phy: air_en8811h: Add the Airoha EN8811H PHY driver
Add the driver for the Airoha EN8811H 2.5 Gigabit PHY. The phy supports
100/1000/2500 Mbps with auto negotiation only.

The driver uses two firmware files, for which updated versions are added to
linux-firmware already.

Note: At phy-address + 8 there is another device on the mdio bus, that
belongs to the EN881H. While the original driver writes to it, Airoha
has confirmed this is not needed. Therefore, communication with this
device is not included in this driver.

Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326162305.303598-3-ericwouds@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-29 12:06:44 -07:00
Russell King (Oracle)
30dc587396 net: phy: qcom: at803x: Avoid hibernating if MAC requires RX clock
Stmmac controllers connected to an at803x PHY cannot resume properly after
suspend when WoL is enabled. This happens because the MAC requires an RX
clock generated by the PHY to initialize its hardware properly. But the RX
clock is cut when the PHY suspends and isn't brought up until the MAC
driver resumes the phylink.

Prevent the at803x PHY driver from going into suspend if the attached MAC
driver always requires an RX clock signal.

Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-6-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28 19:21:34 -07:00
Romain Gantois
dceb393a0a net: phylink: add rxc_always_on flag to phylink_pcs
Some MAC drivers (e.g. stmmac) require a continuous receive clock signal to
be generated by a PCS that is handled by a standalone PCS driver.

Such a PCS driver does not have access to a PHY device, thus cannot check
the PHY_F_RXC_ALWAYS_ON flag. They cannot check max_requires_rxc in the
phylink config either, since it is a private member. Therefore, a new flag
is needed to signal to the PCS that it should keep the RX clock signal up
at all times.

Co-developed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-2-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28 19:21:33 -07:00
Russell King (Oracle)
21d9ba5bc5 net: phylink: add PHY_F_RXC_ALWAYS_ON to PHY dev flags
Some MAC controllers (e.g. stmmac) require their connected PHY to
continuously provide a receive clock signal. This can cause issues in two
cases:

  1. The clock signal hasn't been started yet by the time the MAC driver
     initializes its hardware. This can make the initialization fail, as in
      the case of the rzn1 GMAC1 driver.
  2. The clock signal is cut during a power saving event. By the time the
     MAC is brought back up, the clock signal is still not active since
     phylink_start hasn't been called yet. This brings us back to case 1.

If a PHY driver reads this flag, it should ensure that the receive clock
signal is started as soon as possible, and that it isn't brought down when
the PHY goes into suspend.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-1-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28 19:21:33 -07:00
Christian Marangi
6a4aee2777 net: phy: qcom: at803x: fix kernel panic with at8031_probe
On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.

Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct.

Reported-by: William Wortel <wwortel@dorpstraat.com>
Cc: <stable@vger.kernel.org>
Fixes: 25d2ba9400 ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-28 10:42:22 +01:00
Nikita Kiryushin
32fa4366cc net: phy: fix phy_read_poll_timeout argument type in genphy_loopback
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).

Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.

Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-19 16:09:34 +01:00
Jakub Kicinski
ed1f164038 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Merge in late fixes to prepare for the 6.9 net-next PR.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-11 20:38:36 -07:00
Heiner Kallweit
c786459fc8 net: phy: simplify a check in phy_check_link_status
Handling case err == 0 in the other branch allows to simplify the
code. In addition I assume in "err & phydev->eee_cfg.tx_lpi_enabled"
it should have been a logical and operator. It works as expected also
with the bitwise and, but using a bitwise and with a bool value looks
ugly to me.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/de37bf30-61dd-49f9-b645-2d8ea11ddb5d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-11 13:46:27 -07:00
Andy Shevchenko
22ca20fd12 net: phy: marvell-88x2222: Remove unused of_gpio.h
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307122346.3677534-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-11 13:46:01 -07:00
Andy Shevchenko
86a7abbb22 net: mdio_bus: Remove unused of_gpio.h
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307122231.3677241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-11 13:45:12 -07:00
Tim Pambor
c8a5c731fd net: phy: dp83822: Fix RGMII TX delay configuration
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.

Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69

Fixes: 8095295292 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-08 20:33:44 -08:00
Kévin L'hôpital
4469c0c5b1 net: phy: fix phy_get_internal_delay accessing an empty array
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.

Fixes: 92252eec91 ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-03-08 10:18:33 +00:00
Russell King (Oracle)
8fc80c9d8c net: phy: marvell: add comment about m88e1111_config_init_1000basex()
The comment in m88e1111_config_init_1000basex() is wrong - it claims
that Autoneg will be enabled, but this doesn't actually happen.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1rhos4-003yuQ-5p@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-07 20:48:51 -08:00
Robert Marko
1677293ed8 net: phy: qca807x: fix compilation when CONFIG_GPIOLIB is not set
Kernel bot has discovered that if CONFIG_GPIOLIB is not set compilation
will fail.

Upon investigation the issue is that qca807x_gpio() is guarded by a
preprocessor check but then it is called under
if (IS_ENABLED(CONFIG_GPIOLIB)) in the probe call so the compiler will
error out since qca807x_gpio() has not been declared if CONFIG_GPIOLIB has
not been set.

Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403031332.IGAbZzwq-lkp@intel.com/
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240305142113.795005-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-06 20:39:29 -08:00
Andrew Lunn
49168d1980 net: phy: Add phy_support_eee() indicating MAC support EEE
In order for EEE to operate, both the MAC and the PHY need to support
it, similar to how pause works. With some exception - a number of PHYs
have SmartEEE or AutoGrEEEn support in order to provide some EEE-like
power savings with non-EEE capable MACs.

Copy the pause concept and add the call phy_support_eee() which the MAC
makes after connecting the PHY to indicate it supports EEE. phylib will
then advertise EEE when auto-neg is performed.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 19:21:17 -08:00
Andrew Lunn
3e43b903da net: phy: Immediately call adjust_link if only tx_lpi_enabled changes
The MAC driver changes its EEE hardware configuration in its
adjust_link callback. This is called when auto-neg
completes. Disabling EEE via eee_enabled false will trigger an
autoneg, and as a result the adjust_link callback will be called with
phydev->enable_tx_lpi set to false. Similarly, eee_enabled set to true
and with a change of advertised link modes will result in a new
autoneg, and a call the adjust_link call.

If set_eee is called with only a change to tx_lpi_enabled which does
not trigger an auto-neg, it is necessary to call the adjust_link
callback so that the MAC is reconfigured to take this change into
account.

When setting phydev->enable_tx_lpi, take both eee_enabled and
tx_lpi_enabled into account, so the MAC drivers just needs to act on
phydev->enable_tx_lpi and not the whole EEE configuration.
The same check should be done for tx_lpi_timer too.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240302195306.3207716-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 19:21:17 -08:00
Andrew Lunn
fe0d4fd928 net: phy: Keep track of EEE configuration
Have phylib keep track of the EEE configuration. This simplifies the
MAC drivers, in that they don't need to store it.

Future patches to phylib will also make use of this information to
further simplify the MAC drivers.

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 19:21:17 -08:00
Andrew Lunn
e3b6876ab8 net: phy: Add phydev->enable_tx_lpi to simplify adjust link callbacks
MAC drivers which support EEE need to know the results of the EEE
auto-neg in order to program the hardware to perform EEE or not.  The
oddly named phy_init_eee() can be used to determine this, it returns 0
if EEE should be used, or a negative error code,
e.g. -EOPPROTONOTSUPPORT if the PHY does not support EEE or negotiate
resulted in it not being used.

However, many MAC drivers get this wrong. Add phydev->enable_tx_lpi
which indicates the result of the autoneg for EEE, including if EEE is
administratively disabled with ethtool. The MAC driver can then access
this in the same way as link speed and duplex in the adjust link
callback. If enable_tx_lpi is true, the MAC should send low power
indications and does not need to consider anything else with respect
to EEE.

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 19:21:17 -08:00
Horatiu Vultur
ad080db448 net: phy: micrel: lan8814 cable improvement errata
When the length of the cable is more than 100m and the lan8814 is
configured to run in 1000Base-T Slave then the register of the device
needs to be optimized.

Workaround this by setting the measure time to a value of 0xb. This
value can be set regardless of the configuration.

This issue is described in 'LAN8814 Silicon Errata and Data Sheet
Clarification' and according to that, this will not be corrected in a
future silicon revision.

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240304091548.1386022-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 11:17:46 -08:00
Horatiu Vultur
e9097f8e1e net: phy: micrel: lan8814 led errata
Lan8814 phy led behavior is not correct. It was noticed that the led
still remains ON when the cable is unplugged while there was traffic
passing at that time.

The fix consists in clearing bit 10 of register 0x38, in this way the
led behaviour is correct and gets OFF when there is no link.

Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240304091548.1386022-2-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-05 11:17:46 -08:00
Robert Marko
cb28f70296 net: phy: qcom: qca808x: fill in possible_interfaces
Currently QCA808x driver does not fill the possible_interfaces.
2.5G QCA808x support SGMII and 2500Base-X while 1G model only supports
SGMII, so fill the possible_interfaces accordingly.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2024-03-01 08:56:39 +00:00