ovpn_crypto_kill_key assumes both crypto slots are populated and
dereferences each slot before checking it. That is not guaranteed: a
peer can have only one installed key, and the kill path may be asked to
remove a key that is not present.
Read each slot once while holding the crypto state lock, check for NULL
before looking at key_id, and only replace the slot that actually
matches.
Fixes: 89d3c0e461 ("ovpn: kill key and notify userspace in case of IV exhaustion")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Currently, the destruction of the waiter queue is suppressed for
rqspinlock in cases where a deadlock is detected. Deadlock checks happen
relatively frequently (on entry for AA, within 1ms for ABBA), and waiter
threads may not be involved in locking scenarios involving deadlocks.
Thus, it is useful to not flush the queue and let other waiters take a
stab at acquiring the lock after we detect a deadlock and exit.
However, we need to follow the same logic as what we did previously for
the waitq_timeout label: reset the tail, and if we cannot, signal the
next waiter appropriately. In case of deadlocks, this signal would just
mark the MCS node as unlocked, and in case of timeouts, it would signal
RES_TIMEOUT_VAL. The difference thus is in the value propagated, which
decides whether the queue remains active or gets flushed.
Not doing the tail reset, and waiting for the next waiter can lead to
cases where we are the final waiter, and thus no next waiter arrives,
leading to intermittent stalls in this path. Once the next waiter does
join, we will be unblocked. In the theoretical case when the next waiter
never joins, we risk stalling indefinitely.
This can only happen for ABBA deadlocks, since entry into the wait queue
is guarded with AA checks. A precise sequence of executions leading up
to this scenario can be:
CPU 0 holds lock A.
CPU 1 holds lock B.
CPU 2 attempts lock B, becomes the pending waiter for B.
CPU 0 attempts lock B. B has locked+pending bits set, thus CPU 0 queues.
CPU 1 attempts lock A.
CPU 0 detects an ABBA deadlock.
Once deadlock detection happens for CPU 0, it will sit waiting for the
next waiter in the queue to populate node->next, which will experience
delays until such a waiter arrives.
Fix this by adjusting the logic for the check for deadlocks preceding
the waitq_timeout label. It would make sense to consolidate code for
both cases and use 'ret' to distinguish the value being propagated, but
that is left as an exercise for a future refactoring task to avoid diff
noise in this patch.
Fixes: 7bd6e5ce5b ("rqspinlock: Disable queue destruction for deadlocks")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://patch.msgid.link/20260802021759.1139457-1-memxor@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
-----BEGIN PGP SIGNATURE-----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=MCxD
-----END PGP SIGNATURE-----
Merge tag 'v7.2-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- Fix potential use after free in cifs_try_adding_channels
- Fix SMB1 large directory enumeration
- Minor debug improvement (show compress mount option)
* tag 'v7.2-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: fix SMB1 TRANS2 multi-response truncation in SendReceive()
smb: client: Fix use-after-free in cifs_try_adding_channels()
smb/client: show compress mount option
at91_ping() rearms the watchdog timer from its callback. timer_delete()
neither waits for a running callback nor prevents it from rearming the
timer, so probe failure or driver removal can leave the timer accessing the
devm-allocated at91wdt after it has been freed.
Use timer_shutdown_sync() on both teardown paths. It waits for a running
callback and rejects any attempt by the callback to rearm the timer.
Fixes: 5161b31dc3 ("watchdog: at91sam9_wdt: better watchdog support")
Signed-off-by: Hongyan Xu <getshell@seu.edu.cn>
Link: https://lore.kernel.org/r/20260806060613.1830-1-getshell@seu.edu.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-----BEGIN PGP SIGNATURE-----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=Ier0
-----END PGP SIGNATURE-----
Merge tag 'for-7.2-rc6-fixup-worker-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull Btrfs Fixes 2: Electric Boogaloo from David Sterba:
"This brings back the fixup worker infrastructure.
It's a mechanism to detect pages/folios that are marked dirty without
filesystem knowledge and require COW fixup. The consequence of not
doing so is silent data loss.
The first patch covers the scenarios in detail, also reflecting folio
API port and subpage block size support added in recent years. The
original fixup worker was only for pages.
The patch is relatively big, half of the code is debugging and support
code, the rest is the core design around the detection and fix.
The second patch handles an unlikely case when there's work left
during unmount"
* tag 'for-7.2-rc6-fixup-worker-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: flush the fixup workers during close_ctree
btrfs: trigger cow fixup via dirty_folio()
-----BEGIN PGP SIGNATURE-----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=Nzlf
-----END PGP SIGNATURE-----
Merge tag 'for-7.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix leak in encoded ioctl write
- disable large folios on systems with highmem
- disable block size > page size when there's no transparent hugepage
support (under experimental config)
- reject compressed inline extents without valid LZO headers
- properly initialize cached inode mapping (if block size > page size)
* tag 'for-7.2-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: initialize inode mapping flags for cached inodes
btrfs: disable bs > ps support if no transparent hugepage support
btrfs: fix memory leak in btrfs_do_encoded_write()
btrfs: lzo: reject inline extents without valid headers
btrfs: disable large folios for systems with highmem
Kyle Zeng reported that GC could free a dead SCC partially.
The scenario is as follows:
1) Create two SCCs:
X -. A <-> B
^--'
2) Run the following concurrently:
2-1) send() sk-B to sk-B from sk-X
2-2) close() both A and B
At 2-1), there is a small window where unix_add_edges()
publishes a new edge (B <-> B) to GC but its skb is not queued
by skb_queue_tail().
If 2-2) completes before skb_queue_tail() and GC is triggered,
it judges A <-> B as dead, but B is not freed because GC cannot
collect the not-yet-queued skb holding the B <-> B edge.
X -. A <-> B -. This edge is visible
^--' ^..' but skb is not
This itself is not a problem since the next GC run will judge
B as dead as well and free it finally.
X -. A <.> B -.
^--' ^--'
However, X's SCC forces the next GC to call unix_walk_scc_fast(),
and it iterates over A through B's scc_entry.
Let's unlink scc_entry before freeing the vertex in unix_del_edge().
Fixes: 4090fa373f ("af_unix: Replace garbage collection algorithm.")
Reported-by: Kyle Zeng <kylebot@openai.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Kyle Zeng <kylebot@openai.com>
Fixes: 4090fa373f ("af_unix: Replace garbage collection algorithm.").
Link: https://patch.msgid.link/20260804002155.2233594-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looks like our attempt to keep the PRs smaller have only prevented
this one from getting even bigger. In the last 9 days there were
405 postings explicitly tagged with [PATCH net], vs 687
with [PATCH net-next]. 37% of posted patches being fixes is pretty
crazy, and that's likely undercounting because LLM "researchers"
more often post fixes without knowing to tag the patches for specific
trees. I don't have historic data.
In any case, we keep adjusting the criteria. The next PR will be smaller.
Current release - regressions:
- net: defer netdev KOBJ_ADD uevent until the device is published,
previously rtnl_lock would serialize the accesses vs publishing
- net: explicitly cancel work to avoid races with ref tracker exit
- qrtr: ns: raise lookup limit to 128
- eth: hns3: fix speed configuration residue after driver reload
Previous releases - regressions:
- tcp: do not change rcv_ssthresh in tcp_measure_rcv_mss(),
regressed flows with MSS and scaling_ratio variability
- Revert "net: thunderbolt: Enable end-to-end flow control also
in transmit", broke some platforms (no packets coming thru)
- eth: stmmac: resume PHY before hardware setup when opening
the interface
Previous releases - always broken:
- another pile of fixes for less common protocols (SCTP, TLS, SMC etc.)
- close a couple of AF_PACKET bugs and ways it can build skbs
problematic for the rest of the stack
- bridge: mrp: fix uninitialised bytes on the wire
- net: devmem: prevent net-iov / page mixing, avoid crashes
- eth: atlantic: free RX pages of consumed but not refilled buffers
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=wJxf
-----END PGP SIGNATURE-----
Merge tag 'net-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter.
Looks like our attempt to keep the PRs smaller have only prevented
this one from getting even bigger. In the last 9 days there were
405 postings explicitly tagged with [PATCH net], vs 687 with [PATCH
net-next]. 37% of posted patches being fixes is pretty crazy, and
that's likely undercounting because LLM "researchers" more often post
fixes without knowing to tag the patches for specific trees. I don't
have historic data.
In any case, we keep adjusting the criteria. The next PR will be
smaller.
Current release - regressions:
- net: defer netdev KOBJ_ADD uevent until the device is published,
previously rtnl_lock would serialize the accesses vs publishing
- net: explicitly cancel work to avoid races with ref tracker exit
- qrtr: ns: raise lookup limit to 128
- eth: hns3: fix speed configuration residue after driver reload
Previous releases - regressions:
- tcp: do not change rcv_ssthresh in tcp_measure_rcv_mss(), regressed
flows with MSS and scaling_ratio variability
- Revert "net: thunderbolt: Enable end-to-end flow control also in
transmit", broke some platforms (no packets coming thru)
- eth: stmmac: resume PHY before hardware setup when opening the
interface
Previous releases - always broken:
- another pile of fixes for less common protocols (SCTP, TLS, SMC
etc.)
- close a couple of AF_PACKET bugs and ways it can build skbs
problematic for the rest of the stack
- bridge: mrp: fix uninitialised bytes on the wire
- net: devmem: prevent net-iov / page mixing, avoid crashes
- eth: atlantic: free RX pages of consumed but not refilled buffers"
* tag 'net-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (116 commits)
igc: fix netdev not re-attached after resume if interface is down
tls: don't abort the connection on signal-interrupted sends
net: avoid theoretical races with ref drain
net: Defer netdev KOBJ_ADD uevent until the device is published
MAINTAINERS: dpll: zl3073x: replace Prathosh Satish with Min Li
sctp: clear control chunk transport if it is being removed
net/atm: fix slab-out-of-bounds read in vcc_setsockopt()
s390/ism: Fix UAF of sba and ieq during ism_dev_exit()
packet: use consistent hard_header_len in TX_RING send path
packet: use consistent hard_header_len in non-ring send paths
net: remove CAP_SYS_RAWIO zero-padding in dev_validate_header
bnge: Fix resource leak in bnge_init_nic() error path
ptp: ocp: Fix board ID over-read
tls: rx: restore msg_iter before TLS 1.3 optimistic retry
selftests: tls: add a test for splicing onto a full plaintext record
tls: don't leave a full plaintext sk_msg ring unpushed
xdp: reject clones that overrun skb_shared_info tailroom
mptcp: reclaim forward-allocated memory on RX path errors
mptcp: fastopen: only mark MPTFO subflows with SYN data
mptcp: pm: fix memory leak from alloc-during-teardown race
...
amdgpu_dm_crtc_set_static_screen_optimze() maps sso_enable to the
Replay and PSR1 vsync events. allow_sr_entry is an entry gate, but the
helper currently applies it to both directions.
A non-fast update clears allow_sr_entry. During a modeset, a separate
hardware-programming event keeps self-refresh blocked while the stream
is reprogrammed. If vblank is enabled before the entry delay expires,
the ISM calls the helper with sso_enable false. The early return drops
the disable request, so the vsync events are not set.
After enough fast commits, allow_sr_entry becomes true and the
hardware-programming event can be cleared. Since the vblank reference
remains held, there is no further zero-to-one vblank transition to
restore the missing vsync events. Replay or PSR1 can then become active
while vblank is still enabled.
Gate only requests that enable static-screen optimization. Always
process disable requests so a vblank requestor keeps Replay and PSR1
blocked.
On a Phoenix system, repeated SDDM-to-VT handoffs produced stuck flips
followed by flip_done and commit-wait timeouts. The timeout was not
observed with this change applied.
Fixes: 3c108046e1 ("drm/amd/display: Add power module on Linux")
Assisted-by: Codex:gpt-5.6-sol
Assisted-by: Claude:opus-5
Signed-off-by: David Weber <weber.aulendorf@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit bd0c009821)
Cc: stable@vger.kernel.org
amdgpu_pci_remove() calls drm_dev_unplug() before invoking the fini
routines. After drm_dev_unplug() the drm_dev_enter() guard in
amdgpu_ttm_fini() always returns false, so iounmap() for
aper_base_kaddr is silently skipped. On connected_to_cpu hardware
ioremap_cache() maps the aperture as WB; when iounmap() is skipped the
stale WB PAT entry persists. On reload IP discovery's
memremap(MEMREMAP_WC) on the same aperture range hits a WB/WC conflict,
producing an ioremap error and failing re-probe.
Remove the drm_dev_enter() guard and call iounmap() unconditionally.
The aperture mapping is plain MMIO and does not require device-presence
protection. Surprise-removal cleanup of aper_base_kaddr is already
handled unconditionally by amdgpu_device_unmap_mmio().
Fixes: 62d5f9f711 ("drm/amdgpu: Unmap MMIO mappings when device is not unplugged")
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fb3f68af9f)
Cc: stable@vger.kernel.org
Some older DCE timing generators do not implement is_tg_enabled in
their ops table. Calling it unconditionally when waiting for AV mute
frames causes a NULL pointer dereference on Southern Islands dGPUs
when turning the display off over HDMI.
Check that tg and the required ops exist before waiting for frames.
Fixes: 414da24137 ("drm/amd/display: Add AV mute wait frames to dce110_set_avmute")
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5557
Tested-by: Viktor Jägersküpper <viktor_jaegerskuepper@freenet.de>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2686a0c0aa)
Cc: stable@vger.kernel.org
devres teardown is LIFO. The aperture devres node was registered after
the DRM device node, so devres_release_all() unmaps the aperture before
the DRM device release callback fires amdgpu_device_fini_sw(). IP
sw_fini callbacks (e.g. vcn_v4_0_sw_fini) write to fw_shared through a
pointer derived from aper_base_kaddr, causing a kernel page fault on
probe failure / rollback:
BUG: unable to handle page fault ... PMD 0
RIP: vcn_v4_0_sw_fini+0x7b/0x170 [amdgpu]
Call Trace:
amdgpu_device_fini_sw
amdgpu_driver_release_kms
devm_drm_dev_init_release
devres_release_all
This reverts commit d871e99879.
Fixes: d871e99879 ("drm/amdgpu: fix aperture mapping leak")
Reported-by: Yuansheng Mao <yuansheng.mao@amd.com>
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 336e0cd576)
Cc: stable@vger.kernel.org
Commit 527ba26e50 ("drm/radeon: delete radeon_fence_process in
is_signaled, no deadlock") removed the hardware polling from
radeon_fence_is_signaled() to fix a self-deadlock caused by
wake_up_all(&rdev->fence_queue) being called with the fence queue
lock held.
However, removing the polling entirely causes significant performance
regression (e.g. glxgears FPS drop) because the fence signaled check
becomes purely passive — it only reads the cached last_seq without
probing the GPU, so completed GPU work is not detected in time,
causing unnecessary CPU stalls in sync-heavy workloads.
Fix this by calling radeon_fence_activity() directly instead of
radeon_fence_process(). radeon_fence_activity() reads the hardware
fence counter and updates last_seq via atomic ops without calling
wake_up_all(), thus avoiding the deadlock while restoring timely
fence detection.
Fixes: 527ba26e50 ("drm/radeon: delete radeon_fence_process in is_signaled, no deadlock")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Wang Jiang <jiangwang@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f59ad4cca2)
Cc: stable@vger.kernel.org
The VBIOS for Cyan Skillfish devices (DCN201) indicates there is
DisplayPort ref clock spread spectrum downspread, so the audio clock
is corrected for it.
However, the clock source in this hardware does not seem to actually be
running with a clock downspread, so DisplayPort audio desyncs with video
after several minutes.
Ignore dprefclk SS downspread on CYAN_SKILLFISH2 asic.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5429
Signed-off-by: Travis K. Bangs <tbangs89@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f3a2d86587)
Cc: stable@vger.kernel.org
Check for mmhub0 rather than mmhub1. Looks like a copy
paste typo.
Fixes: d0c989a0aa ("drm/amd/amdgpu : Use the MES INV_TLBS API for tlb invalidation on gfx12_1")
Cc: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Shaoyun Liu <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0e8faef0aa)
Cc: stable@vger.kernel.org
Allocate each ring buffer separately. A single allocation summing all
ring sizes can exceed the page allocator's MAX_ORDER limit and fail;
per-ring buffers stay small enough to satisfy. The existing allocation
style doesn't capture any ring data if the huge allocation fails.
Splitting into multiple allocations helps to capture as much data as
possible for the core dump.
A failed ring is left with a NULL buffer and skipped when formatting.
Fixes: eea85914d1 ("drm/amdgpu: save ring content before resetting the device")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Assisted-by: Claude Code
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3e8e92b789)
Cc: stable@vger.kernel.org
The number of rings with outstanding fences can be large, requiring a
bigger allocation. Such allocations don't need to be physically
contiguous, so use kvzalloc/kvcalloc which fall back to vmalloc when
contiguous memory isn't available. This also matches the existing
kvfree used to free these allocations.
Also guard the allocation with ring_count to avoid passing 0 size to
allocation routines.
Fixes: eea85914d1 ("drm/amdgpu: save ring content before resetting the device")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 74d48bd6b7)
Cc: stable@vger.kernel.org
On GFX rings, amdgpu_cs_p2_ib() passed user-supplied ib_bytes through
to ib->length_dw without a limit, while ring_emit_ib() encodes length
into packet fields. Oversized values can corrupt adjacent control bits
and destabilize command submission.
Add a per-ring IB packet size limit helper and reject command
submissions exceeding the corresponding dword limit before IB
allocation. Use the documented 20-bit limit for GFX/compute/SDMA/VPE,
and apply the MM fallback limit for other ring types.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7f48fa2cf6)
Cc: stable@vger.kernel.org
Creating a user queue can race with a GPU reset. While recovery holds
reset_domain->sem for write, MES is unresponsive, so the ADD_QUEUE from
amdgpu_userq_map_helper() times out (-110) and an otherwise valid queue
create fails:
amdgpu: MES(0) failed to respond to msg=ADD_QUEUE
[drm:mes_userq_map [amdgpu]] *ERROR* Failed to map queue in HW, err (-110)
amdgpu: [drm] *ERROR* ... Failed to map Queue
amdgpu: [drm] *ERROR* ... Failed to create usermode queue
Take reset_domain->sem for read around the map so it runs only once MES
is back up. This mirrors amdgpu_userq_cleanup() and honors the
userq_mutex -> reset_domain->sem order; the reset path never takes
userq_mutex, so there is no deadlock.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a8e151fe62)
Cc: stable@vger.kernel.org
Move fs_reclaim_acquire() to before all lock acquisitions to eliminate
false positive circular locking dependency warning.
This is a 7.2-cycle regression fix suitable for stable backport.
v3: Address Mikhail Gavrilov technical review:
- Clarify that fs_reclaim_acquire/release pair only REGISTERS the
fs_reclaim lock class, does NOT create a static edge when called
with no locks held
- Explain that the actual fs_reclaim -> notifier_lock edge is
established at runtime during memory reclaim -> MMU notifier path
- Add Cc: Arunpravin PaneerSelvam
v2: Address Mikhail Gavrilov review feedback:
- Fix author name: Michael -> Mikhail Gavrilov in all trailers
- Add Fixes: tag to link regression to original commit
- Add Tested-by: Mikhail Gavrilov (tested on RX 7900 XTX)
Fixes: 1d0f5838b1 ("drm/amdgpu: Add lockdep annotations for lock ordering validation")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Analyzed-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Test-case-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Tested-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Arunpravin PaneerSelvam <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 70a1e9849e)
Cc: stable@vger.kernel.org
Needed to properly lock the interface before using it.
Cc: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8e37aa0bd5)
Cc: stable@vger.kernel.org
TA_CNTL2.TRUNCATE_COORD_MODE selects whether texture coordinate
truncation is D3D9/GL/Vulkan conformant. gfx11 reads it and reports it to
userspace via AMDGPU_IDS_FLAGS_CONFORMANT_TRUNC_COORD, but gfx12 never
read it, so the flag was always reported as 0 and userspace fell back to
the non-conformant path.
Read it in gfx_v12_0_constants_init() like gfx11 does.
Fixes: 52cb80c12e ("drm/amdgpu: Add gfx v12_0 ip block support (v6)")
Signed-off-by: Qiang Yu <Qiang.Yu@amd.com>
Reviewed-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4261cbc7b0)
Cc: stable@vger.kernel.org
Like jpeg_v5_0_0, in DPG mode the ring reset path only clears the
JPEG_PG_MODE bit and never resets a hung JRBC, so the post-reset ring test
times out and the driver falls back to a full MODE1 reset.
Temporarily force the static power-gating path during the reset so the
stop/start sequence power-cycles the JPEG block (JMI soft reset + power
off/on), matching the jpeg_v4_0 reset.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e93659cab1)
Cc: stable@vger.kernel.org
Like jpeg_v5_0_0, in DPG mode the ring reset path only clears the
JPEG_PG_MODE bit and never resets a hung JRBC, so the post-reset ring test
times out and the driver falls back to a full MODE1 reset.
Temporarily force the static power-gating path during the reset so the
stop/start sequence power-cycles the JPEG block (JMI soft reset + power
off/on), matching the jpeg_v4_0 reset.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 75a308eef4)
Cc: stable@vger.kernel.org
In DPG mode jpeg_v5_0_0_ring_reset() takes the DPG stop path, which only
clears the JPEG_PG_MODE bit and never resets the JRBC. A hung ring is not
recovered: the post-reset ring test times out and the driver falls back to
a full MODE1 reset.
Temporarily force the static power-gating path during the reset so the
stop/start sequence power-cycles the JPEG block (JMI soft reset + power
off/on), matching the jpeg_v4_0 reset which has no DPG path.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 79b3612827)
Cc: stable@vger.kernel.org
Document the new_device and delete_device sysfs attributes on SPI
controllers:
- Documentation/spi/instantiating-devices.rst: describes when and
why this interface is needed, accepted parameters, usage examples,
and limitations.
- Documentation/ABI/testing/sysfs-class-spi-master: formal ABI
entry for both attributes.
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20260803104614.2548375-3-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Development boards such as the Jetson AGX Orin expose SPI buses
on expansion headers (e.g. the 40-pin header) so that users can
connect and interact with SPI peripherals from userspace. The
standard way to get /dev/spidevB.C character device nodes for
this purpose is to register spi_device instances backed by the
spidev driver.
Today there is no viable way to do this on upstream kernels:
- The spidev driver rejects the bare "spidev" compatible
string in DT, since spidev is a Linux software interface
and not a description of real hardware.
- Vendor-specific compatible strings (e.g. "nvidia,tegra-spidev")
have been rejected by DT maintainers for the same reason.
The I2C subsystem solved an analogous problem by exposing
new_device/delete_device sysfs attributes on each adapter. Add
the same interface to SPI host controllers, so that userspace
(e.g. a systemd unit at boot) can instantiate SPI devices at
runtime without needing anything in device-tree.
The new_device file accepts:
<modalias> <chip_select> [<max_speed_hz> [<mode>]]
where chip_select is required, while max_speed_hz and mode are
optional and default to 0 if omitted. max_speed_hz == 0 is
clamped to the controller's maximum by spi_setup(); mode == 0
selects SPI mode 0 (CPOL=0, CPHA=0).
The modalias is used both as the device identifier and as a
driver_override, so that the device binds to the named driver
directly. This is necessary because some drivers like spidev
deliberately exclude generic names from their id_table.
Devices created this way are limited compared to those declared
via DT or board files:
- No IRQ is assigned (the device gets IRQ 0 / no interrupt).
- No platform_data or device properties are attached.
- No OF node is associated with the device.
These limitations are acceptable for spidev, which only needs a
registered spi_device to expose a character device to userspace.
Only devices created via new_device can be removed through
delete_device; DT and platform devices are unaffected.
The sysfs attributes are gated behind CONFIG_SPI_DYNAMIC since
this feature adds a new way of dynamically instantiating and
removing SPI devices, and the add_lock locking in
spi_unregister_controller() is already conditional on
CONFIG_SPI_DYNAMIC.
The userspace sysfs group is created manually as the last step
of spi_register_controller() and removed as the first step of
spi_unregister_controller(). Removing the group before taking
add_lock means kernfs_drain() completes any in-flight
new_device_store()/delete_device_store() calls before
add_lock is acquired, so unregister never blocks on a store
that is itself waiting for add_lock and no store can be
touching an spi_device that is about to be torn down.
Non-sysfs callers of __spi_add_device() (DT/ACPI dynamic add,
ancillary registration) continue to be protected by the
pre-existing !device_is_registered(&ctlr->dev) check added in
commit ddf75be47c ("spi: Prevent adding devices below an
unregistering controller"): device_del(&ctlr->dev) runs inside
add_lock in spi_unregister_controller() so state_in_sysfs flips
to 0 before add_lock is released.
Link: https://lore.kernel.org/linux-tegra/909f0c92-d110-4253-903e-5c81e21e12c9@nvidia.com/
Signed-off-by: Vishwaroop A <va@nvidia.com>
Link: https://patch.msgid.link/20260803104614.2548375-2-va@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
__igc_resume() calls netif_device_attach() only inside the
netif_running() branch, so an interface that was down during suspend
is never re-attached on resume. It then stays in the not-present state
that __igc_shutdown() set via netif_device_detach(): ethtool reports
ENODEV and every attempt to bring the interface up fails the
netif_device_present() check in __dev_open() with -ENODEV, silently,
since __igc_resume() returns 0. Only reloading the driver recovers the
device.
This is easy to hit in practice because NetworkManager brings managed
interfaces down before sleep unless Wake-on-LAN is configured, making
the adapter unusable after every suspend/resume cycle with WoL
disabled.
Re-attach the netdev on every successful resume, as igb and e1000e do.
Fixes: 6f31d6b643 ("igc: Refactor runtime power management flow")
Cc: stable@vger.kernel.org
Signed-off-by: Philipp David <pd-lkml@3b.pm>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20260804222205.1580328-11-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 94104e3cfa ("arm64: cpufeature: Rename BBML2_NOABORT as BBML3")
renamed the cpu_supports_bbml2_noabort() helper to cpu_supports_bbml3(),
as the Linux-defined "noabort" semantics have now been incorporated into
the architecture under the BBML3 feature.
Update the caller in the SMMUv3 SVA driver to use the new function.
There is a slightly oddity in that the SMMUv3 architecture already
defined BBML2 in such a way that aborts were prohibited, so we use the
BBML3 feature on the CPU to enable BBML2 in the SMMU.
Fixes: 94104e3cfa ("arm64: cpufeature: Rename BBML2_NOABORT as BBML3")
Signed-off-by: Will Deacon <will@kernel.org>
When a signal interrupts a blocking send, tls_tx_records() treats the
resulting -ERESTARTSYS as a transmission failure and marks the socket
errored via tls_err_abort() with the raw error code. Later syscalls
return the kernel-internal errno 512 (ERESTARTSYS) to userspace, as the
signal it stems from is no longer pending during syscall exit and thus
never translated.
An interrupted send is not a connection error: the partially sent record
stays queued and is resent later. Interrupt error codes are therefore
excluded from the abort in the same way as -EAGAIN.
Fixes: b341ca51d2 ("tls: Fix tls_sw_sendmsg error handling")
Signed-off-by: Maximilian Immanuel Brandtner <maxbr@linux.ibm.com>
Link: https://patch.msgid.link/20260805063109.1772314-1-maxbr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Technically, it's illegal to take a ref on a netdev just because
we have a pointer on which we already hold a ref, with no other
protection. This is because our simple per-cpu refcount
implementation cannot atomically read the count.
Let's make sure we cancel outstanding work and never queue more
work for a device we know is dead. This way taking a ref on
a dev we know is on the netdev_work_list is always going to be safe.
Jiangshan Yi reports that the issues is caught by ref tracker infra
leading to a warning:
WARNING: lib/ref_tracker.c:322 at ref_tracker_free
WARNING: lib/ref_tracker.c:246 at ref_tracker_dir_exit
Reported-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Link: https://lore.kernel.org/20260731035135.3917308-2-yijiangshan@kylinos.cn
Fixes: 12c765be84 ("net: turn the rx_mode work into a generic netdev_work facility")
Link: https://patch.msgid.link/20260806022821.2079945-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev_register_kobject() calls device_add(), which emits KOBJ_ADD and
wakes udev, but register_netdevice() only makes the device findable by
name later, in list_netdevice(). A udev worker that reacts to the uevent
can therefore run against a device that no lookup can find yet.
This used to be harmless because the ethtool ioctl took the rtnl_lock
when looking the device up, and register_netdevice() runs under rtnl, so
the worker simply blocked until registration finished. The commit in the
fixes tag moved the lookup out from under rtnl for ops-locked drivers.
Now there is a short window in register_netdevice() between
netdev_register_kobject() until list_netdevice() when the device is not
findable by name.
This was reproduced with the mlx5 driver on a kernel with KASAN enabled
during devlink reload: systemd-udevd's net_driver builtin gets -ENODEV
from ETHTOOL_GDRVINFO, which was preventing interface renaming.
Suppress the uevent in netdev_register_kobject() and emit it from
register_netdevice() next to rtmsg_ifinfo(). This is the last point in
register_netdevice() where no error can happen, so only fully registered
devices are announced: the registration error paths never reach it, and
the device_del() that unwinds them stays silent as well, leaving
userspace with neither an add nor a remove.
Fixes: f994752b11 ("net: ethtool: optionally skip rtnl_lock on IOCTL path")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Link: https://patch.msgid.link/20260806080758.2039586-2-dtatulea@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_make_heartbeat_ack() caches the destination transport in
chunk->transport without taking a reference. When src_out_of_asoc_ok is
enabled, the HEARTBEAT ACK may remain queued on control_chunk_list instead
of being transmitted immediately.
If the peer transport is removed while the chunk is still queued,
sctp_assoc_rm_peer() drops the transport and schedules it for RCU freeing,
but only clears cached transport pointers in out_chunk_list. The queued
control chunk therefore retains a dangling transport pointer.
Once an ASCONF_ACK clears the suppression and the queued control chunk is
transmitted, SCTP dereferences the stale transport pointer, leading to a
use-after-free.
Fix this by also clearing chunk->transport for queued control chunks in
control_chunk_list when removing the transport.
Fixes: 8a07eb0a50 ("sctp: Add ASCONF operation on the single-homed host")
Reported-by: Daniele Linguaglossa <danielelinguaglossa@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/7e1168cb722132152a29d47e5eafaeac4a3bf6f3.1785943120.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vcc_setsockopt() contained an ineffective optlen check:
if (__SO_LEVEL_MATCH(optname, level) && optlen != __SO_SIZE(optname))
return -EINVAL;
If __SO_LEVEL_MATCH(optname, level) evaluated to false (e.g. if the caller
passed a mismatched level), the length check optlen != __SO_SIZE(optname)
was short-circuited and bypassed. Execution then fell through to switch(optname),
calling copy_from_sockptr() assuming optval contained sufficient space.
Furthermore, even if level matched, a cgroup BPF setsockopt filter could shrink
optlen after entry. Because copy_from_sockptr() on kernel pointers uses memcpy(),
this leads to a KASAN slab-out-of-bounds read when optlen is smaller than the
expected structure size.
Fix this by using copy_safe_from_sockptr(), which unconditionally validates
that optlen is at least the expected size before copying. Also change the local
'value' variable type from 'unsigned long' to 'int' so that SO_SETCLP matches
its sizeof(int) ABI encoding on 64-bit systems.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: syzbot+53ecc09fb81df10ef4de@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=53ecc09fb81df10ef4de
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260805131508.3227331-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A ism interrupt handler can be active in parallel with ism_dev_exit(),
accessing freed data structures.
No new interrupts will be generated after unregister_ieq(). Drain ongoing
interrupt handlers by free_irq(), before freeing ism data structures.
Fixes: 684b89bc39 ("s390/ism: add device driver for internal shared memory")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20260805131043.954639-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qihang Tang says:
====================
net: fix hard_header_len races in packet send paths
The packet socket TX paths read dev->hard_header_len independently for
skb allocation and header construction. Concurrent netdevice
reconfiguration (e.g. bonding device type changes) can change this value
in between, leading to mismatched headroom and copy length, and in the
SOCK_RAW case to out-of-bounds writes.
Patch 1 removes the CAP_SYS_RAWIO zero-padding branch in
dev_validate_header(). That branch sizes a memset against the live
dev->hard_header_len while operating on an skb whose headroom was
allocated from an earlier hard_header_len read, so a concurrent increase
can write past the reserved buffer. Removing it first keeps the later
snapshot fixes bisect-safe: they do not replace an earlier skb_under_panic
with a silent overwrite.
Patches 2 and 3 snapshot hard_header_len once per send and use it
consistently for allocation and construction, in the non-ring and TX_RING
paths respectively. The separate SOCK_DGRAM consistency problem between
hard_header_len and header_ops->create remains out of scope, as noted in
the commit messages.
====================
Link: https://patch.msgid.link/20260805125729.19220-1-q.h.hack.winter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tpacket_snd() reads dev->hard_header_len independently for skb
allocation and header construction in tpacket_fill_skb(). Concurrent
netdevice reconfiguration can therefore make the reserved headroom
smaller than the amount later pushed, or make copylen - hard_header_len
negative.
Snapshot hard_header_len once before processing ring frames and use it
for the frame limit, headroom allocation, copy length, and skb
construction. Pass the snapshot to tpacket_fill_skb().
The separate SOCK_DGRAM consistency problem between hard_header_len and
header_ops->create is not addressed here.
Fixes: 69e3c75f4d ("net: TX_RING and packet mmap")
Cc: stable@vger.kernel.org
Signed-off-by: Qihang Tang <q.h.hack.winter@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260805125729.19220-4-q.h.hack.winter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
packet_snd() reads dev->hard_header_len multiple times while allocating
and constructing an skb. Device reconfiguration can change this value
concurrently, for example through bonding device type changes.
For SOCK_RAW, packet_snd() can save a larger value in reserve and later
allocate headroom using a smaller value. Moving skb->data back by reserve
then places it before skb->head, and the following copy from userspace can
attempt an out-of-bounds write.
packet_sendmsg_spkt() has the same issue because it calculates its
reservation and header offset from separate reads before dropping the RCU
read lock to allocate the skb.
Add LL_RESERVED_SPACE_EX() for callers that already saved a header length.
Read hard_header_len once in packet_snd() and use it for allocation and
construction. In packet_sendmsg_spkt(), preserve the allocation-time value
through the device lookup retry.
The separate SOCK_DGRAM consistency problem between hard_header_len and
header_ops->create is not addressed here.
Fixes: b84bbaf7a6 ("packet: in packet_snd start writing at link layer allocation")
Cc: stable@vger.kernel.org
Signed-off-by: Qihang Tang <q.h.hack.winter@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260805125729.19220-3-q.h.hack.winter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_validate_header() reads dev->hard_header_len directly when
zero-padding short link layer headers for CAP_SYS_RAWIO holders:
if (capable(CAP_SYS_RAWIO)) {
memset(ll_header + len, 0, dev->hard_header_len - len);
return true;
}
Packet send paths call dev_validate_header() on skbs whose headroom was
allocated from an earlier hard_header_len read. If the device is
reconfigured so that dev->hard_header_len increases before validation,
the memset writes past the reserved buffer, an out-of-bounds write.
This out-of-bounds write is masked in some SOCK_RAW paths today because
the same concurrent increase can first make skb_push() exceed the
reserved headroom and trigger skb_under_panic(). Remove the zero-padding
branch before making those hard_header_len reads consistent, so the
snapshot fixes do not turn a loud panic into a silent overwrite.
This path is only reached for variable length L2 protocols, where
len < hard_header_len but len >= min_header_len. No remaining in-tree
variable length L2 protocol implements header_ops->validate, and the
CAP_SYS_RAWIO bypass that zero-pads and accepts short headers has no
real value beyond allowing testing of intentionally malformed input.
Drop the CAP_SYS_RAWIO branch. The remaining reads of
dev->hard_header_len in dev_validate_header() are comparisons only and
have no memory safety impact.
Suggested-by: Willem de Bruijn <willemb@google.com>
Fixes: 2793a23aac ("net: validate variable length ll headers")
Cc: stable@vger.kernel.org
Signed-off-by: Qihang Tang <q.h.hack.winter@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260805125729.19220-2-q.h.hack.winter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If bnge_init_chip() fails, bnge_init_nic() jumps to err_free_ring_grps
and returns immediately, skipping cleanup for RX ring pair buffers.
Remove the early return so execution falls through to
err_free_rx_ring_pair_bufs to properly free resources on error.
Fixes: 23df6aebf8 ("bng_en: Allocate stat contexts")
Signed-off-by: Bhargava Marreddy <bhargava.marreddy@broadcom.com>
Reviewed-by: Dharmender Garg <dharmender.garg@broadcom.com>
Reviewed-by: Rajashekar Hudumula <rajashekar.hudumula@broadcom.com>
Link: https://patch.msgid.link/20260805094022.15487-1-bhargava.marreddy@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The EEPROM board ID is a fixed 13-byte field and is not guaranteed to
contain a NUL terminator. Passing it directly to
devlink_info_version_fixed_put() treats it as a C string and may read
beyond the field.
Format at most OCP_BOARD_ID_LEN bytes into the existing local buffer
before reporting the ID. Use a precision limit because the snprintf()
output size alone does not bound the source string scan.
Fixes: 0cfcdd1ebc ("ptp: ocp: add nvmem interface for accessing eeprom")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Byagowi <ahmadexp@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260804210751.48248-1-ahmadexp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tls_decrypt_sg() advances msg->msg_iter when it maps user pages for
the optimistic TLS 1.3 zero-copy path. If the decrypted record turns
out not to be unpadded application data, tls_decrypt_sw() retries into
a kernel skb, but leaves the iterator advanced.
The subsequent copy from the skb then writes decrypted bytes again at
a later point in the caller iovecs while recvmsg() reports only the
post-retry length. A TLS peer can trigger this after the receiver
enables TLS_RX_EXPECT_NO_PAD.
Revert the iterator by the number of bytes consumed by the optimistic
mapping before retrying without zero-copy.
Add a selftest which sends a TLS 1.3 control record with
TLS_RX_EXPECT_NO_PAD enabled and verifies that recvmsg() does not
overwrite later iovecs beyond the returned length.
Fixes: ce61327ce9 ("tls: rx: support optimistic decrypt to user buffer with TLS 1.3")
Cc: stable@vger.kernel.org
Signed-off-by: Jérémy Jean <Jeremy.Jean@oss.cyber.gouv.fr>
Link: https://patch.msgid.link/20260804125528.2139928-1-Jeremy.Jean@oss.cyber.gouv.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
chanyoung says:
====================
tls: fix plaintext sk_msg ring over-fill
An unprivileged user can oops the kernel by splicing into a kTLS socket
whose open record already has a full plaintext sk_msg ring. Reproduced on
net (53658c6f36) with a stock config, no KASAN.
Patch 2 oopses an unpatched kernel and passes with patch 1 applied.
====================
Link: https://patch.msgid.link/20260804052837.49015-1-ppoo1220@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Splicing onto a plaintext sk_msg ring that is already full used to wrap the
ring and make the kernel oops in the scatterwalk once the record was
pushed.
Only the copy path leaves the ring full without pushing it, so splice until
the ring is one fragment short, add the last fragment with a one-byte
MSG_MORE send, and splice once more before pushing the record.
CONFIG_MAX_SKB_FRAGS is 17..45, so that last fragment follows between 16
and 44 splices; sweep that range to trigger the bug on any build.
Signed-off-by: chanyoung <ppoo1220@gmail.com>
Link: https://patch.msgid.link/20260804052837.49015-3-ppoo1220@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the copy path in tls_sw_sendmsg_locked() adds the fragment that fills
the plaintext sk_msg ring, it does not set full_record, so the record is
left full and unpushed. A later splice() then adds to an already full
ring: sk_msg_page_add() has no fullness check of its own, so sg.end wraps
onto sg.start and the ring appears empty. Fragments added after that
overwrite live entries, and sg.size no longer matches what is reachable
between sg.start and sg.end, so pushing the record runs the scatterwalk off
the end of the scatterlist.
An unprivileged user can trigger this on a loopback TCP socket with the
"tls" ULP attached:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:memcpy_from_scatterwalk+0x32/0xc0
Call Trace:
skcipher_walk_next+0x1d1/0x2c0
gcm_encrypt_aesni_avx+0x1e9/0x220
bpf_exec_tx_verdict+0x3bb/0x860
tls_sw_sendmsg+0xa1a/0xca0
__sys_sendto+0x1da/0x1f0
Set full_record in the copy path when the ring becomes full, and push a
record that is already full on entry to the sendmsg loop.
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: fe1e81d4f7 ("tls/sw: Support MSG_SPLICE_PAGES")
Cc: stable@vger.kernel.org
Signed-off-by: chanyoung <ppoo1220@gmail.com>
Link: https://patch.msgid.link/20260804052837.49015-2-ppoo1220@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_get_slot() returns a referenced PCI device. Commit 44c10138fd
("PCI: Change all drivers to use pci_device->revision") replaced a
configuration-space read with direct access to the cached revision field,
but left that access after pci_dev_put(). The bridge may therefore be freed
before its revision is read.
Read the revision before dropping the reference.
Fixes: 44c10138fd ("PCI: Change all drivers to use pci_device->revision")
Signed-off-by: Hongyan Xu <getshell@seu.edu.cn>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
xdpf_clone() clones broadcast copies into a single page and sets
frame_sz to PAGE_SIZE. __xdp_build_skb_from_frame() later treats that
page like a normal XDP frame and expects the usual skb_shared_info
tailroom at the end of the buffer.
The current check only rejects frames whose linear xdp_frame header,
headroom, and packet data exceed PAGE_SIZE. A source frame backed by a
larger allocation can still satisfy that check while extending into the
clone's required shared-info area. When such a clone is converted back
into an skb, build_skb_around() places skb_shared_info over live packet
bytes and later writes can corrupt XDP return metadata.
Reject clones unless their linear area fits inside
SKB_WITH_OVERHEAD(PAGE_SIZE), matching the tailroom requirement already
enforced by the XDP-to-skb conversion path.
Fixes: e624d4ed4a ("xdp: Extend xdp_redirect_map with broadcast support")
Cc: stable@vger.kernel.org
Reported-by: Vega <vega@nebusec.ai>
Signed-off-by: Zhiling Zou <zhilinz@nebusec.ai>
Link: https://patch.msgid.link/6b2afef5d1738763c6965e8e466eb16e43e4f956.1785757386.git.zhilinz@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc fixes for v7.2-rc6
Here are various unrelated fixes:
- Patches 1-3: harden incoming MPTCP suboptions parsing by rejecting
non-combinable ones. Patch 3 removes unreachable code after patch 2
added here for consistency, and to reduce comments from AI reviews.
Fixes for v5.6.
- Patch 4: fix a data race in the ADD_ADDR timer callback. A fix for
v5.13.
- Patch 5: correctly catch data corruption during the MPTCP join
selftest by marking tests as failed, instead of only printing a
warning. A fix for v5.18.
- Patch 6: fix a leak with the userspace ADD_ADDR list in case of race
condition during teardown. A fix for v5.19.
- Patch 7: deal with MPTFO with a valid token, but no data in the SYN. A
fix for v6.2.
- Patch 8: reclaim forward-allocated memory in case of error on the
receive side. A fix for v6.19.
====================
Link: https://patch.msgid.link/20260803-net-mptcp-misc-fixes-7-2-rc6-v2-0-b8f496d71664@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
