On CHV the display DDC pins may be muxed to an alternate function if
there's no need for DDC on a specific port, which is the case for eDP
ports since there's no way to plug in a DP++ HDMI dongle.
This causes problems when trying to determine if the port is present
since the the DP_DETECTED bit is the latched state of the DDC SDA pin
at boot. If the DDC pins are muxed to an alternate function the bit
may indicate that the port isn't present.
To work around this look at the VBT as well as the DP_DETECTED bit
to determine if we should attempt registering an eDP port. Do this
only for ports B and C since port D doesn't support eDP (no PPS/BLC).
In theory someone could also wire up a normal DP port w/o DDC lines.
That would just mean that simple DP++ HDMI dongles wouldn't work
on such a port. With this change we would still fail to register
such DP ports. But let's hope no one wires their board in such a way,
and if they do we can extend the VBT checks to cover normal DP ports
as well.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84265
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().
The following patch is all we need to protect against this panic:
ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiling with CONFIG_FM10K=y and VXLAN=m resulting in linking error:
drivers/built-in.o: In function `fm10k_open':
(.text+0x1f9d7a): undefined reference to `vxlan_get_rx_port'
make: *** [vmlinux] Error 1
The fix follows the same strategy as I40E.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After grabbing the mailbox lock and detecting an error, the lock must be
released before the error code can be returned.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The atmel serial driver uses dmaengine APIs but never included the dmaengine
header as it was getting inculded thru one of driver headers.
commit 3d588f83e4 - "dmaengine: dw: split
dma-dw.h to platform and private parts" broke this as it moved headers
around. Fix this by doing the right thing to include the dmaengine header
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 08f738be88 (serial: at91: add tx dma support)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Set the flag to fetch the host state before kicking off the service task
that reads the host state when bringing the interface back up.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.
The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."
Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case. However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.
Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.
Reported-by: Kristian Otnes <kotnes@cisco.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0b725a2ca6
net: Remove ndo_xmit_flush netdev operation, use signalling instead.
added code that looks at skb->xmit_more after the skb has
been put in TX VQ. Since some paths process the ring and free the skb
immediately, this can cause use after free.
Fix by storing xmit_more in a local variable.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.
ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;
For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.
Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atiixp_ide_timing.
The following Coccinelle semantic patch detects the case:
@tn1@
type td;
@@
typedef struct { ... } td;
@script:python tf@
td << tn1.td;
tdres;
@@
coccinelle.tdres = td;
@@
type tn1.td;
identifier tf.tdres;
@@
-typedef
struct
+ tdres
{ ... }
-td
;
@@
type tn1.td;
identifier tf.tdres;
@@
-td
+ struct tdres
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768
Fixes: 02d04254a5 ("Input: alps - use struct input_mt_pos to track coordinates")
Signed-off-by: Andreas Bosch <linux@progandy.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Identified by kbuild test robot. csk family is always set to be AF_INET or
AF_INET6, so skb will always be initialized to some value but there is no harm
in silencing the warning anyways.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Fixes : f42bb57c61 ('cxgb4i : Fix -Wunused-function warning')
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
carma-fpga driver uses device control with custom FSLDMA_EXTERNAL_START
command. Since we wnat to deprecate the device control, move this driver to
use new fsl_dma_external_start() API
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_slave_config() and dmaengine_prep_dma_sg()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The freescale driver uses custom device control FSLDMA_EXTERNAL_START to
put the controller in external start mode.
Since we are planning to deprecate the device control, move this to exported
API. Subsequent patches will remove the FSLDMA_EXTERNAL_START
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_pause() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of accessing
the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of accessing
the device_control which will be deprecated soon
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch is to fix the stmmac data compatibilities for
all the SoCs inside the platform file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added book keeping of whether or not the 8250-dma driver has an RX
transfer pending or not so we don't BUG here if it calls
dmaengine_pause() on a channel which has not a pending transfer. Guess
what, this is not enough.
The following can be triggered with a busy RX channel and hackbench in
background:
- DMA transfer completes. The callback is delayed via
vchan_cookie_complete() into a tasklet so it das not happen asap.
- hackbench keeps the system busy so the tasklet does not run "soon".
- the UART collected enough data and generates an "timeout"-interrupt.
Since 8250-dma *thinks* the DMA-transfer is still pending it tries to
cancel it via invoking dmaengine_pause() first. This causes the segfault
because echan->edesc is NULL now that the transfer completed (however
the callback did not run yet).
With this patch we don't BUG in the scenario described.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver library functions can be used directly by the compound devices such
as ADSP or serial driver where DesignWare DMA IP is privately attached to the
main hardware.
Instead of creating a new platform device leaf they may call dw_dma_probe()
with given struct dw_dma_chip directly and make sure that the main device is
DMA capable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable controller automatically whenever first user requires for a channel and
disable it when the last user gone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of conditional exporing of dw_dma_suspend() / dw_dma_resume() let's
export dw_dma_disable() / dw_dma_enable(). Since dw_dma_shutdown() repeats
dw_dma_disable() we may safely remove it at all.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As an opposite to dw_dma_off() let's introduce dw_dma_on() helper. It will be
useful later as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The introduced include/linux/dma/dw.h is going to contain the private
extensions and structures which are shared for dw_dmac users in the kernel.
Meanwhile include/linux/platform_data/dma-dw.h keeps only platform related data
types and definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we don't allow user to set registers directly through private slave
configuration we may move definitions to the regs.h because they are not used
anywhere except core.c part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change uses managed resource APIs to allocate resources such as,
mem, irq in order to simplify the driver unload or failure cases
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver is only usable on 64-bit s390 machines. Mark the Kconfig
dependencies to that users on other architectures are not prompted for it.
Fixes: 8f933b1043 ("s390/hmcdrv: HMC drive CD/DVD access")
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In rx mode, dma must be prepared before spi is enabled.
But in tx and tr mode, spi must be enabled first.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the minimum divisor in rk3x's spi controller is 2,
if spi_clk is less than 2 * sclk_out, we can't get the right divisor.
So we must set spi_clk again to match slave request.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'void __iomem *regs' is not used in pl330_submit_req() function.
Remove it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_submit_req() checked supplied 'struct pl330_thread thrd' and
'struct dma_pl330_desc desc' parameters for non-NULL. However these
checks are useless because supplied arguments won't be NULL.
The pl330_submit_req() is called in only one place and:
1. 'desc' is already dereferenced in fill_queue() before calling
pl330_submit_req().
2. 'thrd' is always dereferenced after calling
fill_queue()->pl330_submit_req().
Removing the checks for non-NULL values fixes following warning:
drivers/dma/pl330.c:1376 pl330_submit_req() warn: variable dereferenced before check 'thrd' (see line 1367)
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUPOQPAAoJEHKvRublQaWiZnQP/0bDfPvhaNKZtmDKYzbqQm9x
Gh3fB53d7TtIei///5eD/LUGObg0Ze8g2k8aAC05hcq5Be8Haitma3iDDSvJq6ig
umYU9BWkv47BHQy0gAVMXyaxHocICq7W9bnOvU4SSEW/sWeneBllyxgCfV7EKSTd
B/OXP+Ovr4FtjAweOACCN8b0M9w4wdxNKfDNV+WDIHAddYBngxrwq7zASKNNCx2N
0u9sXIdTp0Fvxmyx/lYLC5NXN0CUDjB3Ffdx3+eehrBp2lT6JdlkYU403c85cIMP
oIPJVKFbOnM04MfCjhFNTrK9OtC2eD6PoWq+FLL0UJx3YW5HkbLsiHGm/2UTJ2Z1
5QOwDebMxlvrb6f6Gv846ADl7YcByiXkieTDHRlOnplVRNV5Sj8UWAgq+zyq7sWq
2uRuW2UvKx7vYoAwKRwCaIoqpIe3NIvZQzE7C9mGOprIawZ5e0YJzaR6OoBs4Y8i
gmBeFx266URJun7isy1R7JJsMjYzxbEXju9zH/SkghbLHnf8yqafIG+pG1GD7n5R
o2C/5TVXjmEhIoDn8j2ZozaElX4mD7REKILpIGaE4XltExNTexq8neRo9D3ajzif
N5RrMCAkBzIxMz83evDppe3ObtkEaf0K43VCO3AVQ2g9jXg7ttKhR2hb8HRqCMHe
Lp3d8qKyZyL/HZ5F62yX
=zJyI
-----END PGP SIGNATURE-----
Merge tag 'llvmlinux-for-v3.18' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull LLVM updates from Behan Webster:
"These patches remove the use of VLAIS using a new SHASH_DESC_ON_STACK
macro.
Some of the previously accepted VLAIS removal patches haven't used
this macro. I will push new patches to consistently use this macro in
all those older cases for 3.19"
[ More LLVM patches coming in through subsystem trees, and LLVM itself
needs some fixes that are already in many distributions but not in
released versions of LLVM. Some day this will all "just work" - Linus ]
* tag 'llvmlinux-for-v3.18' of git://git.linuxfoundation.org/llvmlinux/kernel:
crypto: LLVMLinux: Remove VLAIS usage from crypto/testmgr.c
security, crypto: LLVMLinux: Remove VLAIS from ima_crypto.c
crypto: LLVMLinux: Remove VLAIS usage from libcrc32c.c
crypto: LLVMLinux: Remove VLAIS usage from crypto/hmac.c
crypto, dm: LLVMLinux: Remove VLAIS usage from dm-crypt
crypto: LLVMLinux: Remove VLAIS from crypto/.../qat_algs.c
crypto: LLVMLinux: Remove VLAIS from crypto/omap_sham.c
crypto: LLVMLinux: Remove VLAIS from crypto/n2_core.c
crypto: LLVMLinux: Remove VLAIS from crypto/mv_cesa.c
crypto: LLVMLinux: Remove VLAIS from crypto/ccp/ccp-crypto-sha.c
btrfs: LLVMLinux: Remove VLAIS
crypto: LLVMLinux: Add macro to remove use of VLAIS in crypto code
This pull-request includes:
* Change in the IOMMU-API to convert the former iommu_domain_capable
function to just iommu_capable
* Various fixes in handling RMRR ranges for the VT-d driver (one fix
requires a device driver core change which was acked
by Greg KH)
* The AMD IOMMU driver now assigns and deassigns complete alias groups
to fix issues with devices using the wrong PCI request-id
* MMU-401 support for the ARM SMMU driver
* Multi-master IOMMU group support for the ARM SMMU driver
* Various other small fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OMOt
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This pull-request includes:
- change in the IOMMU-API to convert the former iommu_domain_capable
function to just iommu_capable
- various fixes in handling RMRR ranges for the VT-d driver (one fix
requires a device driver core change which was acked by Greg KH)
- the AMD IOMMU driver now assigns and deassigns complete alias
groups to fix issues with devices using the wrong PCI request-id
- MMU-401 support for the ARM SMMU driver
- multi-master IOMMU group support for the ARM SMMU driver
- various other small fixes all over the place"
* tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Work around broken RMRR firmware entries
iommu/vt-d: Store bus information in RMRR PCI device path
iommu/vt-d: Only remove domain when device is removed
driver core: Add BUS_NOTIFY_REMOVED_DEVICE event
iommu/amd: Fix devid mapping for ivrs_ioapic override
iommu/irq_remapping: Fix the regression of hpet irq remapping
iommu: Fix bus notifier breakage
iommu/amd: Split init_iommu_group() from iommu_init_device()
iommu: Rework iommu_group_get_for_pci_dev()
iommu: Make of_device_id array const
amd_iommu: do not dereference a NULL pointer address.
iommu/omap: Remove omap_iommu unused owner field
iommu: Remove iommu_domain_has_cap() API function
IB/usnic: Convert to use new iommu_capable() API function
vfio: Convert to use new iommu_capable() API function
kvm: iommu: Convert to use new iommu_capable() API function
iommu/tegra: Convert to iommu_capable() API function
iommu/msm: Convert to iommu_capable() API function
iommu/vt-d: Convert to iommu_capable() API function
iommu/fsl: Convert to iommu_capable() API function
...