[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
slower down the HW i2c speed when used by HW i2c.
this request: each acquired_i2c_engine setup the i2c speed needed.
and set the I2c engine for HDCP use at release_engine.
this covers SW using HW I2c engine and HDCP using HW I2c engine. for
dmcu using HW I2c engine, needs add similar logic in dmcufw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as gmc9, basically filter the fault, reroute or handle it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Felix pointed out that we need this for Navi as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Looks like we can't enabled the IH1/IH2 feature for Vega20, make sure
retry faults are handled on a separate ring anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Seems like we won't get the hardware IH1/2 rings on Vega20 working.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a soft IH ring implementation similar to the hardware IH1/2.
This can be used if the hardware delegation of interrupts to IH1/2
doesn't work for some reason.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Return early in case of a ratelimit and don't print leading zeros for
the address.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The address space is only 48bit, not 64bit. And the VMHUBs work with
sign extended addresses.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use generic DMA api instead of bus-specific API.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use generic DMA api instead of bus-specific API.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update GC golden setting for navy_flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple
of warnings by explicitly adding a break statement instead of letting
the code fall through to the next case, and a fallthrough pseudo-keyword
as a replacement for a /* fall through */ comment,
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple fallthrough pseudo-keyword macros,
as replacement for /* fall through */ comments.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The HDCP feature requires at least one connector attached to the device;
however, some GPUs do not have a physical output, making the HDCP
initialization irrelevant. This patch disables HDCP initialization when
the graphic card does not have output.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We only need to arbitrate VGA access on VGA compatible devices.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix check_patch.pl warning:
WARNING: Prefer kmalloc_array over kmalloc with multiply
+bps = kmalloc(align_space * sizeof((*data)->bps), GFP_KERNEL);
WARNING: Prefer kmalloc_array over kmalloc with multiply
+bps_bo = kmalloc(align_space * sizeof((*data)->bps_bo),
GFP_KERNEL);
kmalloc_array has multiply overflow check, which will be safer.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix check_patch.pl warning:
kmalloc_array uses number as first arg, sizeof is generally wrong.
+fences = kmalloc_array(sizeof(void *), id_mgr->num_ids,
GFP_KERNEL);
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support software ring share memory with vcn firmware.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dec software ring vm functions to support.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add vcn software ring decode ring test and decode ib test.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add macro, structure and function prototype to
support vcn dec software ring.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
refactor dec message functions to add dec software ring support.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Default runtime logic not changed.
Provide an alternative runtime method. (set 1 to use BACO; 2 to use BAMACO)
When set reset_method to 4, it will use BACO or BAMACO for gpu reset,
according to runpm value.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some features are still disabled after runtime pm resume. This can take
the hardware back.
Unlike other projects, this doesn't need pptable retransfer.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The UVD firmware is copied to cpu addr in uvd_resume, so it
should be used after that. This is to fix a bug introduced by
patch drm/amdgpu: fix SI UVD firmware validate resume fail.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This has been confirmed that unload message is not needed from SIENNA_CICHLID in reset.
Otherwise it will cause the fw wrong state after reset and no response for any messages.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix the null pointer issue when runtime pm is triggered.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn302 link encoder regs list, so add them.
Just like dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SI UVD firmware validate key is stored at the end of firmware,
which is changed during resume while playing video. So get the key
at sw_init and store it for fw validate using.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
cpuidle->enter() callbacks should not call into tracing because RCU
has already been disabled. Instead of doing the broadcast thing
itself, simply advertise to the cpuidle core that those states stop
the timer.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20201123143510.GR3021@hirez.programming.kicks-ass.net
We call arch_cpu_idle() with RCU disabled, but then use
local_irq_{en,dis}able(), which invokes tracing, which relies on RCU.
Switch all arch_cpu_idle() implementations to use
raw_local_irq_{en,dis}able() and carefully manage the
lockdep,rcu,tracing state like we do in entry.
(XXX: we really should change arch_cpu_idle() to not return with
interrupts enabled)
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/20201120114925.594122626@infradead.org
iov_iter::type is a bitmask that also keeps direction etc., so it
shouldn't be directly compared against ITER_*. Use proper helper.
Fixes: ff6165b2d7 ("io_uring: retain iov_iter state over io_read/io_write calls")
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Cc: <stable@vger.kernel.org> # 5.9
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Abaci Fuzz reported a shift-out-of-bounds BUG in io_uring_create():
[ 59.598207] UBSAN: shift-out-of-bounds in ./include/linux/log2.h:57:13
[ 59.599665] shift exponent 64 is too large for 64-bit type 'long unsigned int'
[ 59.601230] CPU: 0 PID: 963 Comm: a.out Not tainted 5.10.0-rc4+ #3
[ 59.602502] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 59.603673] Call Trace:
[ 59.604286] dump_stack+0x107/0x163
[ 59.605237] ubsan_epilogue+0xb/0x5a
[ 59.606094] __ubsan_handle_shift_out_of_bounds.cold+0xb2/0x20e
[ 59.607335] ? lock_downgrade+0x6c0/0x6c0
[ 59.608182] ? rcu_read_lock_sched_held+0xaf/0xe0
[ 59.609166] io_uring_create.cold+0x99/0x149
[ 59.610114] io_uring_setup+0xd6/0x140
[ 59.610975] ? io_uring_create+0x2510/0x2510
[ 59.611945] ? lockdep_hardirqs_on_prepare+0x286/0x400
[ 59.613007] ? syscall_enter_from_user_mode+0x27/0x80
[ 59.614038] ? trace_hardirqs_on+0x5b/0x180
[ 59.615056] do_syscall_64+0x2d/0x40
[ 59.615940] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 59.617007] RIP: 0033:0x7f2bb8a0b239
This is caused by roundup_pow_of_two() if the input entries larger
enough, e.g. 2^32-1. For sq_entries, it will check first and we allow
at most IORING_MAX_ENTRIES, so it is okay. But for cq_entries, we do
round up first, that may overflow and truncate it to 0, which is not
the expected behavior. So check the cq size first and then do round up.
Fixes: 88ec3211e4 ("io_uring: round-up cq size before comparing with rounded sq size")
Reported-by: Abaci Fuzz <abaci@linux.alibaba.com>
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.
phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d63 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").
Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.
Fixes: 061035d456 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org
If set active without increase the usage count of pm, the dont use
autosuspend function will call the suspend callback to close the two
clocks of spi because the usage count is reduced to -1.
This will cause the warning dump below when the defer-probe occurs.
[ 129.379701] ecspi2_root_clk already disabled
[ 129.384005] WARNING: CPU: 1 PID: 33 at drivers/clk/clk.c:952 clk_core_disable+0xa4/0xb0
So add the get noresume function before set active.
Fixes: 43b6bf406c spi: imx: fix runtime pm support for !CONFIG_PM
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20201124085247.18025-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently array of fix length PM_API_MAX is used to cache
the pm_api version (valid or invalid). However ATF based
PM APIs values are much higher then PM_API_MAX.
So to include ATF based PM APIs also, use hash-table to
store the pm_api version status.
Signed-off-by: Amit Sunil Dhamne <amit.sunil.dhamne@xilinx.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Fixes: f3217d6f2f ("firmware: xilinx: fix out-of-bounds access")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1606197161-25976-1-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some laptops like ASUS UX482EG & B9400CEA's headset audio does not work
until the quirk ALC294_FIXUP_ASUS_HPE is applied.
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201124092024.179540-1-jhp@endlessos.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On resource group creation via a mkdir an extra kernfs_node reference is
obtained by kernfs_get() to ensure that the rdtgroup structure remains
accessible for the rdtgroup_kn_unlock() calls where it is removed on
deletion. Currently the extra kernfs_node reference count is only
dropped by kernfs_put() in rdtgroup_kn_unlock() while the rdtgroup
structure is removed in a few other locations that lack the matching
reference drop.
In call paths of rmdir and umount, when a control group is removed,
kernfs_remove() is called to remove the whole kernfs nodes tree of the
control group (including the kernfs nodes trees of all child monitoring
groups), and then rdtgroup structure is freed by kfree(). The rdtgroup
structures of all child monitoring groups under the control group are
freed by kfree() in free_all_child_rdtgrp().
Before calling kfree() to free the rdtgroup structures, the kernfs node
of the control group itself as well as the kernfs nodes of all child
monitoring groups still take the extra references which will never be
dropped to 0 and the kernfs nodes will never be freed. It leads to
reference count leak and kernfs_node_cache memory leak.
For example, reference count leak is observed in these two cases:
(1) mount -t resctrl resctrl /sys/fs/resctrl
mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
umount /sys/fs/resctrl
(2) mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
rmdir /sys/fs/resctrl/c1
The same reference count leak issue also exists in the error exit paths
of mkdir in mkdir_rdt_prepare() and rdtgroup_mkdir_ctrl_mon().
Fix this issue by following changes to make sure the extra kernfs_node
reference on rdtgroup is dropped before freeing the rdtgroup structure.
(1) Introduce rdtgroup removal helper rdtgroup_remove() to wrap up
kernfs_put() and kfree().
(2) Call rdtgroup_remove() in rdtgroup removal path where the rdtgroup
structure is about to be freed by kfree().
(3) Call rdtgroup_remove() or kernfs_put() as appropriate in the error
exit paths of mkdir where an extra reference is taken by kernfs_get().
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: e02737d5b8 ("x86/intel_rdt: Add tasks files")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085088-31707-1-git-send-email-xiaochen.shen@intel.com
Willem reported growing of kernfs_node_cache entries in slabtop when
repeatedly creating and removing resctrl subdirectories as well as when
repeatedly mounting and unmounting the resctrl filesystem.
On resource group (control as well as monitoring) creation via a mkdir
an extra kernfs_node reference is obtained to ensure that the rdtgroup
structure remains accessible for the rdtgroup_kn_unlock() calls where it
is removed on deletion. The kernfs_node reference count is dropped by
kernfs_put() in rdtgroup_kn_unlock().
With the above explaining the need for one kernfs_get()/kernfs_put()
pair in resctrl there are more places where a kernfs_node reference is
obtained without a corresponding release. The excessive amount of
reference count on kernfs nodes will never be dropped to 0 and the
kernfs nodes will never be freed in the call paths of rmdir and umount.
It leads to reference count leak and kernfs_node_cache memory leak.
Remove the superfluous kernfs_get() calls and expand the existing
comments surrounding the remaining kernfs_get()/kernfs_put() pair that
remains in use.
Superfluous kernfs_get() calls are removed from two areas:
(1) In call paths of mount and mkdir, when kernfs nodes for "info",
"mon_groups" and "mon_data" directories and sub-directories are
created, the reference count of newly created kernfs node is set to 1.
But after kernfs_create_dir() returns, superfluous kernfs_get() are
called to take an additional reference.
(2) kernfs_get() calls in rmdir call paths.
Fixes: 17eafd0762 ("x86/intel_rdt: Split resource group removal in two")
Fixes: 4af4a88e0c ("x86/intel_rdt/cqm: Add mount,umount support")
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: d89b737901 ("x86/intel_rdt/cqm: Add mon_data")
Fixes: c7d9aac613 ("x86/intel_rdt/cqm: Add mkdir support for RDT monitoring")
Fixes: 5dc1d5c6ba ("x86/intel_rdt: Simplify info and base file lists")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Fixes: 4e978d06de ("x86/intel_rdt: Add "info" files to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085053-31639-1-git-send-email-xiaochen.shen@intel.com
The commit 16ada730a7 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDIO recheck fix is required for more of the supported variants. Let's
add it to those that needs it.
Reported-by: Fabien Parent <fparent@baylibre.com>
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/20201119030237.9414-1-yong.mao@mediatek.com
Fixes: 9e2582e574 ("mmc: mediatek: fix SDIO irq issue")
Cc: stable@vger.kernel.org
[Ulf: Clarified commitmsg ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the patchset merged by commit b9fcf0a0d8
("Merge branch 'support-AF_PACKET-for-layer-3-devices'") L3 devices which
did not have header_ops were given one for the purpose of protocol parsing
on af_packet transmit path.
That change made af_packet receive path regard these devices as having a
visible L3 header and therefore aligned incoming skb->data to point to the
skb's mac_header. Some devices, such as ipip, xfrmi, and others, do not
reset their mac_header prior to ingress and therefore their incoming
packets became malformed.
Ideally these devices would reset their mac headers, or af_packet would be
able to rely on dev->hard_header_len being 0 for such cases, but it seems
this is not the case.
Fix by changing af_packet RX ll visibility criteria to include the
existence of a '.create()' header operation, which is used when creating
a device hard header - via dev_hard_header() - by upper layers, and does
not exist in these L3 devices.
As this predicate may be useful in other situations, add it as a common
dev_has_header() helper in netdevice.h.
Fixes: b9fcf0a0d8 ("Merge branch 'support-AF_PACKET-for-layer-3-devices'")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20201121062817.3178900-1-eyal.birger@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36ee ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
