As another precaution when testing whether the CS engine is actually
idle, also inspect the ring's HEAD/TAIL registers, which should be equal
when there are no commands left to execute by the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-3-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
When we enable the GuC, we enable an alternative mechanism for doing
post-GGTT update invalidation. Likewise, when we disable the GuC, we
restore the previous method. Assert that we change between known
endpoints, so that we can catch if we accidentally clobber some other
gen and if we change the invalidate routine without updating guc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601090446.1334-1-chris@chris-wilson.co.uk
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Atm disabling either DP or eDP outputs can generate a spurious short
pulse interrupt. The reason is that after disabling the port the source
will stop sending a valid stream data, while the sink expects either a
valid stream or the idle pattern. Since neither of this is sent the sink
assumes (after an arbitrary delay) that the link is lost and requests
for link retraining with a short pulse.
The spurious pulse is a real problem at least for eDP panels with long
power-off / power-cycle delays: as part of disabling the output we
disable the panel power. The subsequent spurious short pulse handling
will have to turn the power back on, which means the driver has to do a
redundant wait for the power-off and power-cycle delays. During system
suspend this leads to an unnecessary delay up to ~1s on systems with
such panels as reported by Rui.
To fix this put the sink to DPMS D3 state before turning off the port.
According to the DP spec in this state the sink should not request
retraining. This is also what we do already on pre-ddi platforms.
As an alternative I also tried configuring the port to send idle pattern
- which is against BSPec - and leave the port in normal mode before
turning off the port. Neither of these resolved the problem.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
Seems that GLK has a dotclock that's twice the display clock.
skl_max_scale checks for IS_GEMINILAKE, so perform the same check here.
While at it, change the DRM_ERROR to DEBUG_KMS.
Fixes: 73b0ca8ec7 ("drm/i915/skl+: consider max supported plane pixel
rate while scaling")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601103413.7037-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Commit 7c3f86b6dc ("drm/i915: Invalidate the guc ggtt TLB upon
insertion") added the restoration of the invalidation routine after the
GuC was disabled, but missed that the GuC was unconditionally disabled
when not used. This then overwrites the invalidate routine for the older
chipsets, causing havoc and breaking resume as the most obvious victim.
We place the guard inside i915_ggtt_disable_guc() to be backport
friendly (the bug was introduced into v4.11) but it would be preferred
to be in more control over when this was guard (i.e. do not try and
teardown the data structures before we have enabled them). That should
be true with the reorganisation of the guc loaders.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 7c3f86b6dc ("drm/i915: Invalidate the guc ggtt TLB upon insertion")
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Link: http://patchwork.freedesktop.org/patch/msgid/20170531190514.3691-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.
The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
}
Else {
Plane Ratio = 1
}
If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
}
}
Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe
If pipe scaling is enabled {
Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
Pipe Ratio = Pipe Ratio / Pipe down scale amount
}
Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio
In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.
Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com
This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.
Changes since v1:
- Rebase on top of Paulo's patch series
Changes since v2:
- Fix the for loop condition to enable WM
Changes since v3:
- Fix crash in cursor i-g-t reported by Maarten
- Rebase after addressing Paulo's comments
- Few other ULT fixes
Changes since v4:
- Rebase on drm-tip
- Added separate function to enable WM levels
Changes since v5:
- Fix a crash identified in skl-6770HQ system
Changes since v6:
- Address review comments from Matt
Changes since v7:
- Fix failure return in skl_compute_plane_wm (Matt)
- fix typo
Changes since v8:
- Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
- fix typo
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com
On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.
Changes since v1:
- Do not take the connection_mutex, this is already done below.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Inspired-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 98d39494d3 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Since
commit bac2a909a0
Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Date: Wed Jan 21 02:17:42 2015 +0100
PCI / PM: Avoid resuming PCI devices during system suspend
PCI devices will default to allowing the system suspend complete
optimization where devices are not woken up during system suspend if
they were already runtime suspended. This however breaks the i915/HDA
drivers for two reasons:
- The i915 driver has system suspend specific steps that it needs to
run, that bring the device to a different state than its runtime
suspended state.
- The HDA driver's suspend handler requires power that it will request
from the i915 driver's power domain handler. This in turn requires the
i915 driver to runtime resume itself, but this won't be possible if the
suspend complete optimization is in effect: in this case the i915
runtime PM is disabled and trying to get an RPM reference returns
-EACCESS.
Solve this by requiring the PCI/PM core to resume the device during
system suspend which in effect disables the suspend complete optimization.
Regardless of the above commit the optimization stayed disabled for DRM
devices until
commit d14d2a8453
Author: Lukas Wunner <lukas@wunner.de>
Date: Wed Jun 8 12:49:29 2016 +0200
drm: Remove dev_pm_ops from drm_class
so this patch is in practice a fix for this commit. Another reason for
the bug staying hidden for so long is that the optimization for a device
is disabled if it's disabled for any of its children devices. i915 may
have a backlight device as its child which doesn't support runtime PM
and so doesn't allow the optimization either. So if this backlight
device got registered the bug stayed hidden.
Credits to Marta, Tomi and David who enabled pstore logging,
that caught one instance of this issue across a suspend/
resume-to-ram and Ville who rememberd that the optimization was enabled
for some devices at one point.
The first WARN triggered by the problem:
[ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746448] pm_runtime_get_sync() failed: -13
[ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul
snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_
numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915]
[ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1
[ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017
[ 6250.746521] Workqueue: events_unbound async_run_entry_fn
[ 6250.746525] Call Trace:
[ 6250.746530] dump_stack+0x67/0x92
[ 6250.746536] __warn+0xc6/0xe0
[ 6250.746542] ? pci_restore_standard_config+0x40/0x40
[ 6250.746546] warn_slowpath_fmt+0x46/0x50
[ 6250.746553] ? __pm_runtime_resume+0x56/0x80
[ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746610] intel_display_power_get+0x1b/0x40 [i915]
[ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915]
[ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core]
[ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel]
[ 6250.746667] pci_pm_runtime_resume+0x76/0xa0
[ 6250.746672] __rpm_callback+0xb4/0x1f0
[ 6250.746677] ? pci_restore_standard_config+0x40/0x40
[ 6250.746682] rpm_callback+0x1f/0x80
[ 6250.746686] ? pci_restore_standard_config+0x40/0x40
[ 6250.746690] rpm_resume+0x4ba/0x740
[ 6250.746698] __pm_runtime_resume+0x49/0x80
[ 6250.746703] pci_pm_suspend+0x57/0x140
[ 6250.746709] dpm_run_callback+0x6f/0x330
[ 6250.746713] ? pci_pm_freeze+0xe0/0xe0
[ 6250.746718] __device_suspend+0xf9/0x370
[ 6250.746724] ? dpm_watchdog_set+0x60/0x60
[ 6250.746730] async_suspend+0x1a/0x90
[ 6250.746735] async_run_entry_fn+0x34/0x160
[ 6250.746741] process_one_work+0x1f2/0x6d0
[ 6250.746749] worker_thread+0x49/0x4a0
[ 6250.746755] kthread+0x107/0x140
[ 6250.746759] ? process_one_work+0x6d0/0x6d0
[ 6250.746763] ? kthread_create_on_node+0x40/0x40
[ 6250.746768] ret_from_fork+0x2e/0x40
[ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]---
v2:
- Use the new pci_dev->needs_resume flag, to avoid any overhead during
the ->pm_prepare hook. (Rafael)
v3:
- Update commit message to reference the actual regressing commit.
(Lukas)
v4:
- Rebase on v4 of patch 1/2.
Fixes: d14d2a8453 ("drm: Remove dev_pm_ops from drm_class")
References: https://bugs.freedesktop.org/show_bug.cgi?id=100378
References: https://bugs.freedesktop.org/show_bug.cgi?id=100770
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c3 - PCI/PM: Add needs_resume flag
Cc: <stable@vger.kernel.org> # v4.10.x
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com
We are passing parameters in the wrong order to find next zero bit, and
when it doesn't find anything it returns size (offset in the code), which
is always zero.
For reference the function is defined as:
find_next_bit( *addr, size, offset )
The incorrect parameter order was added by commit abddffdf36
("drm/i915/guc: Sanitize GuC client initialization"). Luckily, currently
we only use a single guc client and a single doorbell, which happens to be
zero; therefore it isn't necessary to backport this fix (which would be for
v4.12).
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531000546.30762-1-michel.thierry@intel.com
psr1 is also disabled for panel resolution greater than 32X20.
Added psr2 check to disable only for psr2 panels having resolution
greater than 32X20.
issue was introduced by
commit-id : "acf45d1105"
commit message: "PSR2 is restricted to work with panel resolutions
upto 3200x2000, move the check to intel_psr_match_conditions and fully
block psr."
v2: (Rodrigo)
Add previous commit details which introduced the issue
Fixes: acf45d1105 ("drm/i915/psr: disable psr2 for resolution greater than 32X20")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reported-by: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/49935bdff896ee3140bed471012b9f9110a863a4.1495729964.git.vathsala.nagaraju@intel.com
Currently GVT-g cannot work properly when host GuC submission is
enabled, so make the driver loading failed in this case.
v2:
- use DRM_ERROR as it is a fatal message. (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495878259-7733-2-git-send-email-chuanxiao.dong@intel.com
GVT-g relies on the enable_execlists parameter in i915. If this option
is not enabled for GVT-g, should return -EIO to make i915 driver loading
failed.
v2:
- Use DMR_ERROR as it is a fatal message. (Chris)
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The intel_gvt_sanitize_options will sanitize the GVT related
options before doing initialize the GVT.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
I have a plan to write a quick test to exercise concurrent usage of
i915_gem_shrink(), the simplest way looks to be to have multiple threads
using debugfs/i915_drop_caches. However, we currently take one lock over
the entire function, serialising the calls into i915_gem_shrink() so
reduce the lock coverage.
Testcase: igt/gem_shrink/reclaim
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524162653.5446-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Add kerneldoc for the vma_list stored on the i915_gem_object, in
particular, documenting the expected ordering of elements -- i.e. that
we do expect GGTT VMA first followed by the ppGTT VMA.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525204818.12044-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
SDVO was the last connector that's still using the legacy paths
for properties, and this is with a reason!
This connector implements a lot of properties dynamically,
and some of them shared with the digital connector state,
so sdvo_connector_state subclasses intel_digital_connector_state.
set_property had a lot of validation, but this is handled in the
drm core, so most of the validation can die off. The properties
are written right before enabling the connector, since there is no
good way to update the properties without crtc.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-13-maarten.lankhorst@linux.intel.com
Do the same as other connectors, attempt to detect hdmi audio in
the detect() callback, and only use the force_audio property as
override. Compute has_audio in pipe_config, and use that value
instead of the probed value directly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-12-maarten.lankhorst@linux.intel.com
intel_hdmi supports 3 properties, force_audio, broadcast rgb and
scaling mode. The last one is only created for eDP, so the is_eDP
in set_property is not required.
panel fitting and broadcast rgb are straightforward and only requires
changing compute_config.
force_audio is also used to force DVI mode, which means changes to
compute_config and mode_valid. mode_valid is called with
connection_mutex held, so it can safely dereference connector->state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-11-maarten.lankhorst@linux.intel.com
intel_dp supports 3 properties, scaling mode, broadcast rgb and
force_audio. intel_digital_connector handles the plumbing,
so we only have to hook this up in compute_config and init.
Changes since v1:
- Remove limited_color_range too, unused. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-10-maarten.lankhorst@linux.intel.com
Some atomic properties are common between the various kinds of
connectors, for example a lot of them use panel fitting mode.
It makes sense to put a lot of it in a common place, so each
connector can use it while they're being converted.
Implement the properties required for the connectors:
- scaling mode property
- force audio property
- broadcast rgb
- aspect ratio
While at it, make clear that intel_digital_connector_atomic_get_property
is a hack that has to be removed when all connector properties
are converted to atomic.
Changes since v1:
- Scaling mode and aspect ratio are partly handled in core now.
Changes since v2:
- Split out the scaling mode / aspect ratio changes to a preparation
patch.
- Use mode_changed for panel fitter, changes to this property
are checked by fastset.
- Allowed_scaling_modes is removed, handled through core now.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-6-maarten.lankhorst@linux.intel.com
None of the intel connectors can use all types of scaling modes,
so only try the ones that are possible. This is another preparation
for connectors towards conversion to atomic.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-5-maarten.lankhorst@linux.intel.com
[mlankhorst: Use renamed drm_connector_attach_scaling_mode_property function]
The first step in converting connector properties to atomic is
wiring up the atomic state. We're still not completely supoprting
the scaling mode in the atomic case, but this is the first step
towards it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-4-maarten.lankhorst@linux.intel.com
This is a follow-up patch to the previous patch ([PATCH[1/2] drm/i915:
Disable decoupled MMIO) to remove the dead code for decoupled MMIO
implementation, as it won't be used any longer on GEN9LP.
Therefore, this patch reverts:
commit 85ee17ebee
Author: Praveen Paneri <praveen.paneri@intel.com>
Date: Tue Nov 15 22:49:20 2016 +0530
drm/i915/bxt: Broxton decoupled MMIO
Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-3-kai.chen@intel.com
The decoupled MMIO feature doesn't work as intended by HW team. Enabling
it with forcewake will only make debugging efforts more difficult, so
let's disable it.
Fixes: 85ee17ebee ("drm/i915/bxt: Broxton decoupled MMIO")
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Praveen Paneri <praveen.paneri@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-2-kai.chen@intel.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2lrAAoJEHm+PkMAQRiGm3AH/13F1DlIk05aSXHoDr/idIpR
GMHmk3YF+EuFjsL463Sh6s/SSWmz0Lda8euaoB4wCWvQFX2ZjTE+aOd79XlRiZJQ
OTtLkV9I41eXIJUpEOHia7xZiCsbw+usqcHrm1aBoSh5KKV2iQmEOrnJdibqJVOF
eXUMphNK/zFtAd2bKtQSxkaBnOOqsQUgVQSkr2K9rSg25l0KokFC6c5K5IjLn4x9
QgDY4wmMvHrDz0CtpoqlNM4XqbsDJVrFeZGfg6hlMqSRDeXeg4h3Ol0VfIT496RP
QBdrDb6hWO+HKt9B0M+7Q+8a/Fsw+5dtpqv1W/Wlr0i4CS6euU8NChAmrpkrqGo=
=m5ba
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc3' into drm-next
Linux 4.12-rc3
Daniel has requested this for some drm-intel-next work.
More stuff for 4.13:
- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)
* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
drm/i915: Update DRIVER_DATE to 20170529
drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
drm/i915/guc: capture GuC logs if FW fails to load
drm/i915/guc: Introduce buffer based cmd transport
drm/i915/guc: Disable send function on fini
drm: Add definition for eDP backlight frequency
drm/i915: Drop AUX backlight enable check for backlight control
drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
drm/i915: Only GGTT vma may be pinned and prevent shrinking
drm/i915: Serialize GTT/Aperture accesses on BXT
drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
drm/i915/guc: Skip port assign on first iteration of GuC dequeue
drm/i915: Remove misleading comment in request_alloc
drm/i915/g33: Improve reset reliability
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/huc: Update GLK HuC version
drm/i915: Check for allocation failure
drm/i915/guc: Remove action status and statistics from debugfs
drm/i915/g4x: Improve gpu reset reliability
...
Pull thermal SoC management fixes from Eduardo Valentin:
- fixes to TI SoC driver, Broadcom, qoriq
- small sparse warning fix on thermal core
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: broadcom: ns-thermal: default on iProc SoCs
ti-soc-thermal: Fix a typo in a comment line
ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
thermal: core: make thermal_emergency_poweroff static
thermal: qoriq: remove useless call for of_thermal_get_trip_points()
Here are some serial and tty fixes for 4.12-rc3. They are a bit
"bigger" than normal, which is why I had them "bake" in linux-next for a
few weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring things
back to how they were in 4.11, to try to make things a bit more stable
there. Rob and Johan both agree that this is the way forward, so this
isn't people squabbling over semantics. Other than that, just a few
minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWSlOHA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylDCACgn7RHT16JUASggJmRUBeadxQcFQAAnjtxX2kc
0AQLqXxqGyFxVZClAYMy
=Y6+X
-----END PGP SIGNATURE-----
Merge tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
than normal, which is why I had them bake in linux-next for a few
weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring
things back to how they were in 4.11, to try to make things a bit more
stable there. Rob and Johan both agree that this is the way forward,
so this isn't people squabbling over semantics. Other than that, just
a few minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues"
* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: altera_uart: call iounmap() at driver remove
serial: imx: ensure UCR3 and UFCR are setup correctly
MAINTAINERS/serial: Change maintainer of jsm driver
serial: enable serdev support
tty/serdev: add serdev registration interface
serdev: Restore serdev_device_write_buf for atomic context
serial: core: fix crash in uart_suspend_port
tty: fix port buffer locking
tty: ehv_bytechan: clean up init error handling
serial: ifx6x60: fix use-after-free on module unload
serial: altera_jtaguart: adding iounmap()
serial: exar: Fix stuck MSIs
serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
serdev: fix tty-port client deregistration
Revert "tty_port: register tty ports with serdev bus"
drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:
- Export memory_error() so the NFIT module can utilize it
- Handle memory errors in NFIT correctly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
acpi, nfit: Fix the memory error check in nfit_handle_mce()
x86/MCE: Export memory_error()
Pull input layer fixes from Dmitry Torokhov:
"Just a few fixups to a couple of drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - ignore signals when finishing updating firmware
Input: elan_i2c - clear INT before resetting controller
Input: atmel_mxt_ts - add T100 as a readable object
Input: edt-ft5x06 - increase allowed data range for threshold parameter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZKIBGAAoJEL1qUBy3i3wmVmgP/39LC2rvbxUIXK2V4qwuOmhM
1ScGhqCxMVBkb6/iBV7Ilk18LZbRXLCaO7fylpg/rK38HorblFIrp+5LOfS0qyjr
tfLEiWcNLHEO5kh+hQi1JyfxEjJT7xXISF07VdvZ/YUR6lyU7fZL93cC+bFSPaYI
vvpygbahkBrw/4+AyFunXBgSiF5F6ITg/9fSK/BsCheVRV7CHy1WBVwy5hYhQZVP
OIOznLds9bGUrUIHF8oqy8JB7D+qnXuGi+B3un6erw39KH6Z1cHnIfMk5GWgjsfN
OXAnrhZPgObyysw2m20+uSwtMVND88aXl1NWGZi1tlcy2aB067XfjM+Y1JiOGc+0
NEMOnSaelsshieQEAPFV1DUONTyKGmBlaTQ5fXXs9hoBjk9/kpCEGyzWWAYG3Kwa
zRowqBG9DlBBuwtMwji0KuzxaK+adRItkI/2F8Igf0pLFa3NQYZpCVfHRViX6Arb
MXiWvanmahvaZlFOmAS0hVRqLZzKXQMJC9PVVJ8qnIv+Qk1IX6FqAQNYTLbnBpje
a/tJMOaciKni7K6ft89vU+3cfNHmhvqRifV8k2D3ZlAmHx0gmDIIA3JCX1l0+xJA
oU5IfiMjKoIB+F13DUDlyPJK5QIC/heyuyM7UJuVgrYcaIPCE8tfWthGVZVWQ50w
v0pB9t2vmSEXizwhYpT7
=EtW3
-----END PGP SIGNATURE-----
Merge tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for 4.12-rc3.
leds-pca955x driver uses only i2c_smbus API and thus it should pass
I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality"
* tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Correct I2C Functionality
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.
Fixes: 825a2ff189 ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:
- A set of NVMe fixes, pulled from Christoph. This includes a set of
fixes for the fiber channel bits from James Smart, rdma queue depth
fix from Marta, controller removal fixes from Ming, and some more
APST quirk updates from Andy.
- A blk-mq debugfs fix from Bart, fixing a problem with the
untangling of the sysfs and debugfs blk-mq bits that was added in
this series.
- Error code fix in add_partition() from Dan.
- A small series of fixes for the new blk-throttle code from Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block: (21 commits)
blk-mq: Only register debugfs attributes for blk-mq queues
nvme: Quirk APST on Intel 600P/P3100 devices
nvme: only setup block integrity if supported by the driver
nvme: replace is_flags field in nvme_ctrl_ops with a flags field
nvme-pci: consistencly use ctrl->device for logging
partitions/msdos: FreeBSD UFS2 file systems are not recognized
block: fix an error code in add_partition()
blk-throttle: force user to configure all settings for io.low
blk-throttle: respect 0 bps/iops settings for io.low
blk-throttle: output some debug info in trace
blk-throttle: add hierarchy support for latency target and idle time
nvme_fc: remove extra controller reference taken on reconnect
nvme_fc: correct nvme status set on abort
nvme_fc: set logging level on resets/deletes
nvme_fc: revise comment on teardown
nvme_fc: Support ctrl_loss_tmo
nvme_fc: get rid of local reconnect_delay
blk-mq: remove blk_mq_abort_requeue_list()
nvme: avoid to use blk_mq_abort_requeue_list()
nvme: use blk_mq_start_hw_queues() in nvme_kill_queues()
...
Hikey board. Together with a couple of DTS updates for the Hikey board we have
also extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence for the
WiFi chip.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZKCWUAAoJEP4mhCVzWIwpmQ4P/RwUxeM3U29xp2+Zf/Rn20oR
BKjPbSoXs+5OmeLrEre5MikjY6hjYmWXBBBIBwORVZbtGpMwDTT5T9aLQ1usu5b4
VIqLvKj6D1a85Ssu0/KKT5ue7VzOeZudQfcdpIE73wB5kzyWPzcEg0yqDQM9eAFx
IDkefpwL8YImAoPmBAVlTpiovqstSvKORJRM5TVpREw0+P6qy3vH1hWRpFB6CFfG
rrT8Rv+7xGPsIrsaU2SNl+2w8sF2cXXTs2IW7dQciCEM+hUuzYAb20fxwqKhRQsh
zFyoF3NzhHJzz48v3NWJFKncWcVFlzv4xfa1bxsUSUbpikRWl7sxWkAVU4QSF7pq
71Vqim7zgE5Nt3hSx85lUWTvSoOkNDPhirAWBhfPv/zd8d6Gn2rET1GfhQhPrd43
Gf8Axz2Mbr4g+x05e7meGyzpv0FScbhvY00tcuyTLQ3inoyyC+3OxnbSRgnGuz22
cJxCQ34LELYKxSQDpdODjGrHywWOwgjlATgzE6OiA0OFFbDR4PhEVMsAFimi+i69
XsTWvoz56NA+NOImpKSnztXdTm/PAjBzCuc6Ii49OS1wEgKVHCA46YeF9I0NWt6E
yqTwcKScJcBfFf6etsA9mV+A+jGCBImye6jCuLJAJsWE2qACv1B12DfLdW0LFQl7
6e6OAtw02hEs0HPvMsHP
=ECeh
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
-----BEGIN PGP SIGNATURE-----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=XRcK
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not a whole lot happening here, a set of amdgpu fixes and one core
deadlock fix, and some misc drivers fixes"
* tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
drm/gma500/psb: Actually use VBT mode when it is found
drm: Fix deadlock retry loop in page_flip_ioctl
drm: qxl: Delay entering atomic context during cursor update
drm/radeon: Fix oops upon driver load on PowerXpress laptops
Currently the timer is armed for 1ms after the first use and is killed
immediately, dropping the forcewake as early as possible. However, for
very frequent operations the forcewake dance has a large impact on
latency and keeping the timer alive until we are idle is preferred. To
achieve this, if we call intel_uncore_forcewake_get whilst the timer is
alive (repeated use), then set a flag to restart the timer on expiry
rather than drop the forcewake usage count. The timer is racy, the
consequence of the race is to expire the timer earlier than is now
desired but does not impact on correct behaviour. The offset the race
slightly, we set the active flag again on intel_uncore_forcewake_put.
The effect should be to reduce the jitter of reacquiring the fw every
1ms on a busy system. However, the cost is to keep the timer alive for
an extra 1ms on a nearly idle system. We chose to incur the jitter
previously to keep the timer off for as much as possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526132209.14640-1-chris@chris-wilson.co.uk
We're currently deleting the GuC logs if the FW fails to load, but those
are still useful to understand why the loading failed. Keeping the
object around allows us to access them after driver load is completed.
v2: keep the object around instead of using kernel memory (chris)
don't store the logs in the gpu_error struct (Chris)
add a check on guc_log_level to avoid snapshotting empty logs
v3: use separate debugfs for error log (Chris)
v4: rebased
v5: clean up obj selection, move err_load inside guc_log, move err_load
cleanup, rename functions (Michal)
v6: move obj back to intel_guc, move functions to intel_uc.c, don't
clear obj on new GuC load, free object only if enable_guc_loading
is set (Michal)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495475428-19295-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Tested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Buffer based command transport can replace MMIO based mechanism.
It may be used to perform host-2-guc and guc-to-host communication.
Portions of this patch are based on work by:
Michel Thierry <michel.thierry@intel.com>
Robert Beckett <robert.beckett@intel.com>
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
v2: use gem_object_pin_map (Chris)
don't use DEBUG_RATELIMITED (Chris)
don't track action stats (Chris)
simplify next fence (Chris)
use READ_ONCE (Chris)
move blob allocation to new function (Chris)
v3: use static owner id (Daniele)
v4: but keep channel initialization generic (Daniele)
and introduce owner_sub_id (Daniele)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-3-michal.wajdeczko@intel.com
In earlier patch 789a625 we were enabling send function only
after successful init. For completeness, we should make sure
that we disable it on fini.
v2: don't group steps by submission flag (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-2-michal.wajdeczko@intel.com
There are some panel that
(1) does not support display backlight enable via AUX
(2) support display backlight adjustment via AUX
(3) support display backlight enable via eDP BL_ENABLE pin
The current driver required that (1) must be support to enable (2).
This patch drops that requirement.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-2-puthik@chromium.org