The RF calibrations are moved into firmware, so we trigger calibrations by
H2C commands and wait for C2H completion events. However, these events
can be received only after HCI (i.e. PCI for now) starts, so we should
do initial RF calibrations after that.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-11-pkshih@realtek.com
Calling RF calibrations when interface up, connection, switching bands and
going to scan.
For 8922AE, RF calibrations are moved to firmware, so use H2C commands to
trigger RF calibrations and wait for a C2H event to indicate completion.
Then, do next RF calibration.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-10-pkshih@realtek.com
TSSI is short for transmitter signal strength indication, which is a
close-loop hardware circuit to feedback actual transmitting power as a
reference to adjust power for next transmission.
When connecting and switching bands or channels, do TSSI calibration and
reset hardware status to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-9-pkshih@realtek.com
TXGAPK stands for TX power gap calibration. Use this calibration to
compensate TX power gap to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-8-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output signals with expected quality.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-7-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-6-pkshih@realtek.com
RX DCK is receiver DC calibration. This will calibrate DC offset to
reflect correct received signal strength indicator, so mechanisms like CCA
can have normalized values.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-5-pkshih@realtek.com
IQ signal calibration is a basic and important calibration to yield good RF
performance. Do this calibration on AP channel if we are going to connect.
During scanning phase, it transmits with low data rate, so without IQK
RF performance is still acceptable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-4-pkshih@realtek.com
We are going to do RF calibrations in firmware, so driver needs to provide
channel information for calibrations, which can do the same things as
they did in driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-3-pkshih@realtek.com
The RF calibrations should be executed one by one, so add a completion
to ensure one is finish before next. The report from C2H event contains
state and optional version, and we only check the state for now. We also
care about the time a RF calibration takes, so record start time before
asking firmware to do calibration and get the delta time when receiving
report.
Consider SER recovery, we can't receive C2H event, use half of argument
'ms' as fixed delay that is 2 times of measured maximum time of
calibrations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240202030642.108385-2-pkshih@realtek.com
When the feature_flags and xdp_zc_max_segs fields were added to the libbpf
bpf_xdp_query_opts, the code writing them did not use the OPTS_SET() macro.
This causes libbpf to write to those fields unconditionally, which means
that programs compiled against an older version of libbpf (with a smaller
size of the bpf_xdp_query_opts struct) will have its stack corrupted by
libbpf writing out of bounds.
The patch adding the feature_flags field has an early bail out if the
feature_flags field is not part of the opts struct (via the OPTS_HAS)
macro, but the patch adding xdp_zc_max_segs does not. For consistency, this
fix just changes the assignments to both fields to use the OPTS_SET()
macro.
Fixes: 13ce2daa25 ("xsk: add new netlink attribute dedicated for ZC max frags")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240206125922.1992815-1-toke@redhat.com
[Differences from V2:
- Remove conditionals in the source files pragmas, as the
pragma is supported by both GCC and clang.]
Both GCC and clang implement the -Wno-address-of-packed-member
warning, which is enabled by -Wall, that warns about taking the
address of a packed struct field when it can lead to an "unaligned"
address.
This triggers the following errors (-Werror) when building three
particular BPF selftests with GCC:
progs/test_cls_redirect.c
986 | if (ipv4_is_fragment((void *)&encap->ip)) {
progs/test_cls_redirect_dynptr.c
410 | pkt_ipv4_checksum((void *)&encap_gre->ip);
progs/test_cls_redirect.c
521 | pkt_ipv4_checksum((void *)&encap_gre->ip);
progs/test_tc_tunnel.c
232 | set_ipv4_csum((void *)&h_outer.ip);
These warnings do not signal any real problem in the tests as far as I
can see.
This patch adds pragmas to these test files that inhibit the
-Waddress-of-packed-member warning.
Tested in bpf-next master.
No regressions.
Signed-off-by: Jose E. Marchesi <jose.marchesi@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240206102330.7113-1-jose.marchesi@oracle.com
Now that the driver core can properly handle constant struct bus_type,
move the rbd_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-block-v1-1-fc77afd8d7cc@marliere.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the required nodes to support display on X1E80100.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-7-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for all USB controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-6-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-4-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-2-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the IPCC node, used to send and receive IPC signals with
remoteprocs.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-1-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The TCSR clock controller found on X1E80100 provides refclks
for PCIE, USB and UFS. Add clock driver for it.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-9-7fb08c861c7c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add bindings documentation for the X1E80100 Camera Clock Controller.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-5-7fb08c861c7c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The block is the same between these platforms, at least from devicetree
point of view. So drop the dedicated schema and use the SM8550 one instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-1-7fb08c861c7c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
TEST_VM_ASYNC_OPS_ERROR is broken and unused. Remove for now and will
pull back in a later time when it is used, fixed, and properly hidden
behind a Kconfig option. Also fixup the supported flags value.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240206045010.2981051-1-matthew.brost@intel.com
The detection of dirty-throttled tasks in blk-wbt has been subtly broken
since its beginning in 2016. Namely if we are doing cgroup writeback and
the throttled task is not in the root cgroup, balance_dirty_pages() will
set dirty_sleep for the non-root bdi_writeback structure. However
blk-wbt checks dirty_sleep only in the root cgroup bdi_writeback
structure. Thus detection of recently throttled tasks is not working in
this case (we noticed this when we switched to cgroup v2 and suddently
writeback was slow).
Since blk-wbt has no easy way to get to proper bdi_writeback and
furthermore its intention has always been to work on the whole device
rather than on individual cgroups, just move the dirty_sleep timestamp
from bdi_writeback to backing_dev_info. That fixes the checking for
recently throttled task and saves memory for everybody as a bonus.
CC: stable@vger.kernel.org
Fixes: b57d74aff9 ("writeback: track if we're sleeping on progress in balance_dirty_pages()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240123175826.21452-1-jack@suse.cz
[axboe: fixup indentation errors]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
New memory map layout changes (by Qualcomm firmware) have brought
in updates to base addresses and/or size for different memory regions
like cpcucp_fw, tz-stat, and also introduces new memory regions for
resource manager firmware. The updated memory map also fixes existing
issues pertaining to boot up failure while running memtest, thus
improving stability.
This change brings in these corresponding memory map updates to the
device tree for SA8775P SoC platform, which currently is in its
development stage.
Signed-off-by: Ninad Naik <quic_ninanaik@quicinc.com>
Tested-by: Eric Chanudet <echanude@redhat.com> # sa8775p-ride
Link: https://lore.kernel.org/r/20240125055134.7015-1-quic_ninanaik@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
commit dfad37051a ("remap_range: move permission hooks out of
do_clone_file_range()") moved the permission hooks from
do_clone_file_range() out to its caller vfs_clone_file_range(),
but left all the fast sanity checks in do_clone_file_range().
This makes the expensive security hooks be called in situations
that they would not have been called before (e.g. fs does not support
clone).
The only reason for the do_clone_file_range() helper was that overlayfs
did not use to be able to call vfs_clone_file_range() from copy up
context with sb_writers lock held. However, since commit c63e56a4a6
("ovl: do not open/llseek lower file with upper sb_writers held"),
overlayfs just uses an open coded version of vfs_clone_file_range().
Merge_clone_file_range() into vfs_clone_file_range(), restoring the
original order of checks as it was before the regressing commit and adapt
the overlayfs code to call vfs_clone_file_range() before the permission
hooks that were added by commit ca7ab48240 ("ovl: add permission hooks
outside of do_splice_direct()").
Note that in the merge of do_clone_file_range(), the file_start_write()
context was reduced to cover ->remap_file_range() without holding it
over the permission hooks, which was the reason for doing the regressing
commit in the first place.
Reported-and-tested-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401312229.eddeb9a6-oliver.sang@intel.com
Fixes: dfad37051a ("remap_range: move permission hooks out of do_clone_file_range()")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240202102258.1582671-1-amir73il@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The only remaining user of ->d_real() method is d_real_inode(), which
passed NULL inode argument to get the real data dentry.
There are no longer any users that call ->d_real() with a non-NULL
inode argument for getting a detry from a specific underlying layer.
Remove the inode argument of the method and replace it with an integer
'type' argument, to allow callers to request the real metadata dentry
instead of the real data dentry.
All the current users of d_real_inode() (e.g. uprobe) continue to get
the real data inode. Caller that need to get the real metadata inode
(e.g. IMA/EVM) can use d_inode(d_real(dentry, D_REAL_METADATA)).
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240202110132.1584111-3-amir73il@gmail.com
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
file_dentry() is a relic from the days that overlayfs was using files with
a "fake" path, meaning, f_path on overlayfs and f_inode on underlying fs.
In those days, file_dentry() was needed to get the underlying fs dentry
that matches f_inode.
Files with "fake" path should not exist nowadays, so make file_dentry() a
simple accessor and use an assertion to make sure that file_dentry() was
not papering over filesystem bugs.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240202110132.1584111-2-amir73il@gmail.com
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The early startup code executes from a 1:1 mapping of memory, which
differs from the mapping that the code was linked and/or relocated to
run at. The latter mapping is not active yet at this point, and so
symbol references that rely on it will fault.
Given that the core kernel is built without -fPIC, symbol references are
typically emitted as absolute, and so any such references occuring in
the early startup code will therefore crash the kernel.
While an attempt was made to work around this for the early SEV/SME
startup code, by forcing RIP-relative addressing for certain global
SEV/SME variables via inline assembly (see snp_cpuid_get_table() for
example), RIP-relative addressing must be pervasively enforced for
SEV/SME global variables when accessed prior to page table fixups.
__startup_64() already handles this issue for select non-SEV/SME global
variables using fixup_pointer(), which adjusts the pointer relative to a
`physaddr` argument. To avoid having to pass around this `physaddr`
argument across all functions needing to apply pointer fixups, introduce
a macro RIP_RELATIVE_REF() which generates a RIP-relative reference to
a given global variable. It is used where necessary to force
RIP-relative accesses to global variables.
For backporting purposes, this patch makes no attempt at cleaning up
other occurrences of this pattern, involving either inline asm or
fixup_pointer(). Those will be addressed later.
[ bp: Call it "rip_rel_ref" everywhere like other code shortens
"rIP-relative reference" and make the asm wrapper __always_inline. ]
Co-developed-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/all/20240130220845.1978329-1-kevinloughlin@google.com
For small bitmaps that aren't PAGE_SIZE aligned *and* that are less than
512 pages in bitmap length, use an extra page to be able to cover the
entire range e.g. [1M..3G] which would be iterated more efficiently in a
single iteration, rather than two.
Fixes: b058ea3ab5 ("vfio/iova_bitmap: refactor iova_bitmap_set() to better handle page boundaries")
Link: https://lore.kernel.org/r/20240202133415.23819-10-joao.m.martins@oracle.com
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Tested-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Leverage previously added MOCK_FLAGS_DEVICE_HUGE_IOVA flag to create an
IOMMU domain with more than MOCK_IO_PAGE_SIZE supported.
Plumb the hugetlb backing memory for buffer allocation and change the
expected page size to MOCK_HUGE_PAGE_SIZE (1M) when hugepage variant test
cases are used. These so far are limited to 128M and 256M IOVA range tests
cases which is when 1M hugepages can be used.
Link: https://lore.kernel.org/r/20240202133415.23819-9-joao.m.martins@oracle.com
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add support to mock iommu hugepages of 1M (for a 2K mock io page size). To
avoid breaking test suite defaults, the way this is done is by explicitly
creating a iommu mock device which has hugepage support (i.e. through
MOCK_FLAGS_DEVICE_HUGE_IOVA).
The same scheme is maintained of mock base page index tracking in the
XArray, except that an extra bit is added to mark it as a hugepage. One
subpage containing the dirty bit, means that the whole hugepage is dirty
(similar to AMD IOMMU non-standard page sizes). For clearing, same thing
applies, and it must clear all dirty subpages.
This is in preparation for dirty tracking to mark mock hugepages as
dirty to exercise all the iova-bitmap fixes.
Link: https://lore.kernel.org/r/20240202133415.23819-8-joao.m.martins@oracle.com
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Move the clearing of the dirty bit of the mock domain into
mock_domain_test_and_clear_dirty() helper, simplifying the caller
function.
Additionally, rework the mock_domain_read_and_clear_dirty() loop to
iterate over a potentially variable IO page size. No functional change
intended with the loop refactor.
This is in preparation for dirty tracking support for IOMMU hugepage mock
domains.
Link: https://lore.kernel.org/r/20240202133415.23819-7-joao.m.martins@oracle.com
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>