When interrupts are delivered using memory based mechanism, engines
will write status to the report page at the offset (in bytes) that
corresponds to their interrupt bit from the GT_INTR_DW register.
Add engine interrupt offset definitions to engine info as we will
need this to process memory based interrupts.
Bspec: 46149, 50829, 50844
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231214185955.1791-6-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
The new memory based interrupt processing uses additional entries
in the context. Add required definitions.
Bspec: 45585, 60184
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231214185955.1791-4-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
The RING_INT_SRC_RPT_PTR register points to a cacheline in memory
to which an engine must report as source of interrupt prior to
generating an interrupt to the host.
The RING_INT_STATUS_RPT_PTR register points to the first cacheline
of the Interrupt Status Report (ISR) page (4KB) in graphics memory
to which all engines report their interrupt status.
The RING_IMR register has the interrupt enables and interrupt masks
for an engine.
We will refer to these registers shortly.
Bspec: 45963, 45964, 45965
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231214185955.1791-3-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
We will need this shortly during context state preparation.
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231214185955.1791-2-michal.wajdeczko@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Pre-production hardware is anything before C0 (for DG2-G10), before B1
(for DG2-G11), or before A1 (for DG2-G12). Workarounds specific to such
hardware was already removed from i915 in commit eaeb4b3614
("drm/i915/dg2: Drop pre-production GT workarounds") and there's even
less value keeping these around in the Xe driver.
v2:
- Drop Wa_14011441408 from xe_mocs.c. (Gustavo)
- Drop Wa_14010648519, Wa_14010198302, and Wa_1608949956 which were
mis-implemented; they were only supposed to apply to early steppings
of DG2-G10, but were being applied unconditionally on all DG2.
(Gustavo)
- Drop reference to Wa_16011620976; the implementation stays because it
still matches Wa_22015475538. (Gustavo)
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/20231215214531.2576215-2-matthew.d.roper@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Having a different value for op is not possible: this is already kept
out of user-visible warning by the check in xe_wait_user_fence_ioctl()
if op > MAX_OP. The warning is useful as if this switch() is not update
when a new op is added, it should be triggered.
Fix warning as reported by 0-DAY CI Kernel:
drivers/gpu/drm/xe/xe_wait_user_fence.c:46:2: warning: variable 'passed' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
Closes: https://lore.kernel.org/oe-kbuild-all/202312170357.KPSinwPs-lkp@intel.com/
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20231218163301.3453285-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
"err" is not initialized when failing to create and add the freq0 sysfs
file. Remove it from the message. This fixes the following warning with
clang:
../drivers/gpu/drm/xe/xe_gt_freq.c:202:30: error: variable 'err' is uninitialized when used here [-Werror,-Wuninitialized]
kobject_name(gt->sysfs), err);
^~~
Fixes: bef52b5c7a ("drm/xe: Create a xe_gt_freq component for raw management and sysfs")
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://lore.kernel.org/r/20231220161923.3740489-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A revert of
3dec89b14d ("net/ipv6: Remove expired routes with a separated list of routes")
was sent for net-next. Revert the remainder of 5a08d0065a
which added a warn on if a fib entry is still on the gc_link list
to avoid compile failures when net is merged to net-next
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231219030742.25715-1-dsahern@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Set the card.components string using the new rt5645_components() helper
which returns a components string based on the DMI quirks inside the
rt5645 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-8-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPD Win and Teclast X80 Pro both only have 1 speaker add information
about this to the components string.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5645 codec driver uses DMI quirks to configure the DMIC data-pins,
which means that it knows which DMIC interface is used on a specific
device.
ATM we duplicate this DMI matching inside the UCM profiles to select
the right DMIC interface. Add a rt5645_components() helper which the
machine-driver can use to set the components string of the card so
that UCM can get the info from the components string.
This way we only need to add new DMI quirks in one place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a rt5645_get_pdata() helper function which retreives the platform-data
and overrides it with the quirks module parameter if that is set.
This is a preparation patch for adding the rt5645_components() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor rt5645_parse_dt(), make it take a pointer to
struct rt5645_platform_data as argument instead of passing in
the complete rt5645_priv struct.
While at it also make it void since it always succeeds.
This is a preparation patch for factoring the code to get
the platform-data out into a separate helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Acer Switch V 10 uses the default jack-detect mode 3, but instead of
using an analog microphone it is using a DMIC on dmic-data-pin 1,
like other models following Intel's Braswell's reference design.
Add a DMI quirk pointing to the intel_braswell_platform_data for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dmi_platform_data[] first contains a DMI entry matching:
DMI_MATCH(DMI_PRODUCT_NAME, "EF20"),
and then contains an identical entry except for the match being:
DMI_MATCH(DMI_PRODUCT_NAME, "EF20EA"),
Since these are partial (non exact) DMI matches the first match
will also match any board with "EF20EA" in their DMI product-name,
drop the second, redundant, entry.
Fixes: a4dae468cf ("ASoC: rt5645: Add ACPI-defined GPIO for ECS EF20 series")
Cc: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20231126214024.300505-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the STM32MP25:
- Burst should not be enabled with the new DMA used on STM32MP25.
- STM32MP25 SPI8 has a limited feature set, it can only send words of
8 or 16 bits and with a maximum words number of 1024.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://msgid.link/r/20231218155721.359198-4-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add st,stm32mp25-spi compatible in dt-bindings. STM32MP25 spi is similar
to the STM32H7 except for the following two points:
- Burst should not be enabled with the new DMA used on STM32MP25.
- STM32MP25 SPI8 has a limited feature set, it can only send words of
8 or 16 bits and with a maximum words number of 1024.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://msgid.link/r/20231218155721.359198-3-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of our links use relative paths in order to point to files in the
source tree, e.g.:
//! C header: [`include/linux/printk.h`](../../../../include/linux/printk.h)
/// [`struct mutex`]: ../../../../include/linux/mutex.h
These are problematic because they are hard to maintain and do not support
`O=` builds.
Instead, provide support for `srctree`-relative links, e.g.:
//! C header: [`include/linux/printk.h`](srctree/include/linux/printk.h)
/// [`struct mutex`]: srctree/include/linux/mutex.h
The links are fixed after `rustdoc` generation to be based on the absolute
path to the source tree.
Essentially, this is the automatic version of Tomonori's fix [1],
suggested by Gary [2].
Suggested-by: Gary Guo <gary@garyguo.net>
Reported-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Closes: https://lore.kernel.org/r/20231026.204058.2167744626131849993.fujita.tomonori@gmail.com [1]
Fixes: 48fadf4400 ("docs: Move rustdoc output, cross-reference it")
Link: https://lore.kernel.org/rust-for-linux/20231026154525.6d14b495@eugeo/ [2]
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Link: https://lore.kernel.org/r/20231215235428.243211-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Currently, `CondVar::wait()` is an interruptible wait, and this is
different than `wait_event()` in include/linux/wait.h (which is an
uninterruptible wait). To avoid confusion between different APIs on the
interruptible/uninterruptible, make `CondVar::wait()` an uninterruptible
wait same as `wait_event()`, also rename the old `wait()` to
`CondVar::wait_interruptible()`.
Spotted-by: Tiago Lam <tiagolam@gmail.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Tiago Lam <tiagolam@gmail.com>
Link: https://lore.kernel.org/r/20231214200421.690629-1-boqun.feng@gmail.com
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
HX-C2000 is a new CPU made by HEXIN Technologies Co., Ltd. And a new PVN
0x0066 has been applied from the OpenPower Community for this CPU.
Here is a patch to make perf tool run in the CPU.
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: JiaLong.Yang <jialong.yang@shingroup.cn>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: shenghui.qu@shingroup.cn
Cc: Zhao Ke <ke.zhao@shingroup.cn>
Cc: zhijie.ren@shingroup.cn
Link: https://lore.kernel.org/r/20231221060242.4532-1-jialong.yang@shingroup.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ENOTSUPP isn't a standard error code, don't use it. Replace with
EOPNOTSUPP instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.a69f4347b5f8.I88429d5de8251287ec0b58ff26a588465b9049a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware can allow to clear the internal debug buffer. This can be
used to sanitize the data when requested to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.99aed3efbacb.Ib5bda1d1ff4bae476667737d4081ad066d1d7e6b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, this isn't allowed. The API to mac80211 isn't great
for this, but we need to change the API to move puncturing
into the chanctx/chandef, and will do it better then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.38955b68b429.I0c4ae99179b271648a747a51eb04853504c7952c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't want to duplicate the definitions later,
so add them to the API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.6595e905997b.I12354d31676911b29ab30c81a4e9b87f59284d3b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the CSR register details for new wifi7 devices and
correctly set rf_name for devices with FM and WP radios.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.a9c04b1e9d13.Ibf258d5e6370d8840a2560282988a1c26377c410@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
eSR is activated when a chanctx is assigned to more than one link.
During eSR activation we should disable RLC for both phys, and configure
the FW with a special phy command for both phys.
Currently we assign the phy_ctxt to the link only after eSR activation,
so RLC is not disabled for the new phy_ctxt, and a cmd is not sent to FW.
Fix this by first assigning the new phy_ctxt to the link and then
doing the eSR activation.
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.3d94507f5d9a.I537fcd73aedf94c7348c03157e486f24301fef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver copies the userspace buffer into an internal NUL
byte terminated buffer. While doing so, it was reading beyond
the end of the userspace buffer, overwriting its own NUL
termination in the process.
Fix this by only copying the correct number of bytes.
Fixes: 3f244876ef ("wifi: iwlwifi: make debugfs entries link specific")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.e4913deb2ad4.Idcf6a7e909ff4b7801cd49c2f691f84a2f68eff9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that though multiple links are enabled we cannot enabled
EMLSR enable more than a single link, e.g., all valid links are on the
same band etc. Thus, do not warn in case no valid link pair is found.
Fixes: b9be67fb42 ("wifi: iwlwifi: mvm: Add basic link selection logic")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.142e57a05230.I7cfe78c94c3d15c4c744bccadd8f187e43594932@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now with the mac80211 locking model changed, we no longer can
cause any bad dependencies here between mvm->mutex and other
mutexes in mac80211, so we no longer need to drop the mutex
early or even temporarily. Clean this up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.1f2f5289ecc6.I7e3b8e806b6d50e88ba0c26767da8261806eb9c7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we want to drop packets, that's surely a good thing to
do when we want to enter rfkill. Send this command despite
rfkill so we can successfully clean up everything, we need
to handle it separately since it has CMD_WANT_SKB, so it's
not going to automatically return success when in rfkill.
Fixes: d4e3a341b8 ("iwlwifi: mvm: add support for new flush queue response")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.c528a6fa6cec.Ibe5e9560359ccc0fba60c35e01de285c376748a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NVM_CHANNEL_ACTIVE bit means that active scanning/beaconing is
allowed, however it's not an exact opposite of IEEE80211_CHAN_NO_IR.
For example, NVM_CHANNEL_ACTIVE bit is not set on DFS channels, while
cfg80211 doesn't really expect NO-IR on DFS channels.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.94cd9b96a532.Ifb0e8d8a6a6384493758f26b811d58432536101a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware changed their mind, don't set the chains to zero,
instead set them to 1 as we normally would for connections to
APs that don't use MIMO.
Fixes: 2a7ce54ccc ("iwlwifi: mvm: honour firmware SMPS requests")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.7f031f1a127f.Idc816e0f604b07d22a9d5352bc23c445512fad14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During ieee80211_set_active_links() we do (among the others):
1. Call drv_change_vif_links() with both old_active and new_active
2. Unassign the chanctx for the removed link(s) (if any)
3. Assign chanctx to the added link(s) (if any)
4. Call drv_change_vif_links() with the new_active links bitmap
The problem here is that during step #1 the driver doesn't know whether
we will activate multiple links simultaneously or are just doing a link
switch, so it can't check there if multiple links are supported/enabled.
(Some of the drivers might enable/disable this option dynamically)
And during step #3, in which the driver already knows that,
returning an error code (for example when multiple links are not
supported or disabled), will cause a warning, and we will still complete
the transition to the new_active links.
(It is hard to undo things in that stage, since we released channels etc.)
Therefore add a driver callback to check if the desired new_active links
will be supported by the driver or not. This callback will be called
in the beginning of ieee80211_set_active_links() so we won't do anything
before we are sure it is supported.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20231220133549.64c4d70b33b8.I79708619be76b8ecd4ef3975205b8f903e24a2cd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle a case of time overflow, where the switch time might
be smaller than the partial TSF in the beacon.
Additionally, apply advertised TTLM earlier in order to be
ready on time on the newly activated links.
Fixes: 702e80470a ("wifi: mac80211: support handling of advertised TID-to-link mapping")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.15079c34e5c8.I0dd50bcceff5953080cdd7aee5118b72c78c6507@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_update_known_bss will always consume the passed IEs. As such,
cfg80211_update_assoc_bss_entry also needs to always set the pointers to
NULL so that no double free can occur.
Note that hitting this would probably require being connected to a
hidden BSS which is then doing a channel switch while also switching to
be not hidden anymore at the same time.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.8891edb28d51.Id09c5145363e990ff5237decd58296302e2d53c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_bss_update is expected to consume the IEs that are passed into
it in the temporary internal BSS. This did not happen in some error
cases (which are also WARN_ON paths), so change the code to use a common
label and use that everywhere.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.8e72ea105e17.Ic81e9431e980419360e97502ce8c75c58793f05a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a more of a cosmetic fix. The branch will only be taken if
proberesp_ies is set, which implies that beacon_ies is not set unless we
are connected to an AP that just did a channel switch. And, in that case
we should have found the BSS in the internal storage to begin with.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.b898e22dadff.Id8c4c10aedd176ef2e18a4cad747b299f150f9df@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting the radiotap timestamp, the mactime field is
usually unused, we take the data from the device_timestamp.
However, there can be cases where the radiotap timestamp is
better reported as a 64-bit value, so since the mactime is
free, add a flag to support using the mactime as a 64-bit
radiotap timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.00c8b9234f0c.Ie3ce5eae33cce88fa01178e7aea94661ded1ac24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only have a single flag free, and before using that for
another mactime flag, instead refactor the mactime flags
to use a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.d0e664832d14.I20c8900106f9bf81316bed778b1e3ce145785274@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
UHB AP send supported power type(LPI, SP, VLP)
in beacon and probe response IE and STA should
connect to these AP only if their regulatory support
the AP power type.
Beacon/Probe response are reported to userspace
with reason "STA regulatory not supporting to connect to AP
based on transmitted power type" and it should
not connect to AP.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.cbfbef9170a9.I432f78438de18aa9f5c9006be12e41dc34cc47c5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may support concurrent DFS operation which relies on the
BSS channel width for its relaxations. Notify cfg80211 about BW change
so it can schedule regulatory checks.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.e08f8e9ebc67.If8915d13e203ebd380579f55fd9148e9b3f43306@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to different relaxation policies it may be needed to re-check
channels after a BSS station interface is disconnected or performed a
channel switch.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.1f2f8475bcf1.I1879d259d8d756159c8060f61f4bce172e6d323e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FCC-594280 D01 Section B.3 allows peer-to-peer and ad hoc devices to
operate on DFS channels while they operate under the control of a
concurrent DFS master. For example, it is possible to have a P2P GO on a
DFS channel as long as BSS connection is active on the same channel.
Allow such operation by adding additional regulatory flags to indicate
DFS concurrent channels and capable devices. Add the required
relaxations in DFS regulatory checks.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.bdfb8a9c7c54.I973563562969a27fea8ec5685b96a3a47afe142f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>