efx_nic::stats_lock is used to serialise stats updates, but each
reader was dropping it before it finished reading efx_nic::mac_stats.
If there were concurrent stats reads using procfs, or one using procfs
and one using ethtool, an update could race with a read. On a 32-bit
system, the reader could see word-tearing of 64-bit stats (32 bits of
the old value and 32 bits of the new).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When the MC reboots, either as part of a firmware upgrade or due to a
bug, it attempts to complete (with an error) any requests that were
outstanding before the reboot. Since there is an inherent race
condition in checking this, it will also write to a status word in
shared memory.
If we look at each of these separately, we may detect each reboot
twice, resulting in a spurious command failure after a firmware
upgrade or frustrating recovery from a firmware bug. Instead, if a
request completion indicates a reboot, we must poll and clear the
status word.
This bug was previously masked by use of an incorrect address for the
status word. Fix that, using the definition now included in
mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
By the time we look at the MAC address in efx_probe_port(), either the
driver or the firmware has already validated the board configuration.
The possibility of having an invalid MAC address just isn't worth
considering. It certainly isn't worth having a compile-time option
for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Magic constants like 0x0134 in code just invite questions on
where they come from, what they mean, can they be changed.
Provide #defines for the architecturally defined MCACOD values
with a reference to the Intel Software Developers manual which
describes them.
Signed-off-by: Tony Luck <tony.luck@intel.com>
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:
regval |= GPMC_CONFIG1_DEVICESIZE(wval);
so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 2f0778af (ARM: 7205/2: sched_clock: allow sched_clock to be
selected at runtime) had a typo for the case when CONFIG_OMAP_32K_TIMER
is not set.
In dmtimer_read_sched_clock(), wrong argument was getting passed to
__omap_dm_timer_read_counter() function call; instead of "&clksrc",
we were passing "clksrc.io_base", which results into kernel crash.
To reproduce kernel crash, just disable the CONFIG_OMAP_32K_TIMER config
option (and DEBUG_LL) and build/boot the kernel.
This will use dmtimer as a kernel clocksource and lead to kernel
crash during boot -
[ 0.000000] OMAP clocksource: GPTIMER2 at 26000000 Hz
[ 0.000000] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every
165191ms
[ 0.000000] Unable to handle kernel paging request at virtual address
00030ef1
[ 0.000000] pgd = c0004000
[ 0.000000] [00030ef1] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.3.0-rc1-11574-g0c76665-dirty #3)
[ 0.000000] PC is at dmtimer_read_sched_clock+0x18/0x4c
[ 0.000000] LR is at update_sched_clock+0x10/0x84
[ 0.000000] pc : [<c00243b8>] lr : [<c0018684>] psr: 200001d3
[ 0.000000] sp : c0641f38 ip : c0641e18 fp : 0000000a
[ 0.000000] r10: 151c3303 r9 : 00000026 r8 : 76276259
[ 0.000000] r7 : 00028547 r6 : c065ac80 r5 : 431bde82 r4 : c0655968
[ 0.000000] r3 : 00030ef1 r2 : fb032000 r1 : 00000028 r0 : 00000001
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 36a1211970 removed linux/module.h
include statement from one of the headers that end up in net/sock.h.
It was providing us with static_branch() definition implicitly, so
after its removal the build got broken.
To fix this, and avoid having this happening in the future,
let me do the right thing and include linux/jump_label.h
explicitly in sock.h.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Audigy's SB1394 controller is actually from Texas Instruments
and has the same bus reset packet generation bug, so it needs the
same quirk entry.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Setting link parameters on a netdevice changes the value
of if_nlmsg_size(), therefore it is necessary to recalculate
min_ifinfo_dump_size.
Signed-off-by: Stefan Gula <steweg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK. Sit and
ipip set this unconditionally in ops->setup, but gre enables it
conditionally after parameter passing in ops->newlink. This is
not called during tunnel setup as below, however, so GRE tunnels are
still taking the lock.
modprobe ip_gre
ip tunnel add test0 mode gre remote 10.5.1.1 dev lo
ip link set test0 up
ip addr add 10.6.0.1 dev test0
# cat /sys/class/net/test0/features
# $DIR/test_tunnel_xmit 10 10.5.2.1
ip route add 10.5.2.0/24 dev test0
ip tunnel del test0
The newlink callback is only called in rtnl_netlink, and only if
the device is new, as it calls register_netdevice internally. Gre
tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL,
which calls ipgre_tunnel_locate, which calls register_netdev.
rtnl_newlink is called at 'ip link set', but skips ops->newlink
and the device is up with locking still enabled. The equivalent
ipip tunnel works fine, btw (just substitute 'method gre' for
'method ipip').
On kernels before /sys/class/net/*/features was removed [1],
the first commented out line returns 0x6000 with method gre,
which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip,
it reports 0x7000. This test cannot be used on recent kernels where
the sysfs file is removed (and ETHTOOL_GFEATURES does not currently
work for tunnel devices, because they lack dev->ethtool_ops).
The second commented out line calls a simple transmission test [2]
that sends on 24 cores at maximum rate. Results of a single run:
ipip: 19,372,306
gre before patch: 4,839,753
gre after patch: 19,133,873
This patch replicates the condition check in ipgre_newlink to
ipgre_tunnel_locate. It works for me, both with oseq on and off.
This is the first time I looked at rtnetlink and iproute2 code,
though, so someone more knowledgeable should probably check the
patch. Thanks.
The tail of both functions is now identical, by the way. To avoid
code duplication, I'll be happy to rework this and merge the two.
[1] http://patchwork.ozlabs.org/patch/104610/
[2] http://kernel.googlecode.com/files/xmit_udp_parallel.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise (on sparc64):
drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode_amd: Add support for CPU family specific container files
x86/amd: Add missing feature flag for fam15h models 10h-1fh processors
x86/boot-image: Don't leak phdrs in arch/x86/boot/compressed/misc.c::Parse_elf()
x86/numachip: Drop unnecessary conflict with EDAC
x86/uv: Fix uninitialized spinlocks
x86/uv: Fix uv_gpa_to_soc_phys_ram() shift
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
rsyslog will display KERN_EMERG messages on a connected
terminal. However, these messages are useless/undecipherable
for a general user.
For example, after a softlockup we get:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Stack:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Call Trace:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Code: ff ff a8 08 75 25 31 d2 48 8d 86 38 e0 ff ff 48 89
d1 0f 01 c8 0f ae f0 48 8b 86 38 e0 ff ff a8 08 75 08 b1 01 4c 89 e0 0f 01 c9 <e8> ea 69 dd ff 4c 29 e8 48 89 c7 e8 0f bc da ff 49 89 c4 49 89
This happens because the printk levels for these messages are
incorrect. Only an informational message should be displayed on
a terminal.
I modified the printk levels for various messages in the kernel
and tested the output by using the drivers/misc/lkdtm.c kernel
modules (ie, softlockups, panics, hard lockups, etc.) and
confirmed that the console output was still the same and that
the output to the terminals was correct.
For example, in the case of a softlockup we now see the much
more informative:
Message from syslogd@intel-s3e37-04 at Jan 25 10:18:06 ...
BUG: soft lockup - CPU4 stuck for 60s!
instead of the above confusing messages.
AFAICT, the messages no longer have to be KERN_EMERG. In the
most important case of a panic we set console_verbose(). As for
the other less severe cases the correct data is output to the
console and /var/log/messages.
Successfully tested by me using the drivers/misc/lkdtm.c module.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: dzickus@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1327586134-11926-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This will let the MSIC driver to create platform device for the
thermal driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: jacob.jun.pan@linux.intel.com
Link: http://lkml.kernel.org/n/tip-rh1jaft9tjpzfql76gd56h1q@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Intel Medfield platform we use MSIC MFD driver to create
necessary platform devices so it is essential to have the driver
compiled into the kernel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: jacob.jun.pan@linux.intel.com
Link: http://lkml.kernel.org/n/tip-7hp1otk4wf4mg5pqohcwt06w@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All production devices operate in the Oaktrail configuration
with legacy PC elements present and an ACPI BIOS. Continue
stripping out the Moorestown elements from the tree leaving
Medfield.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: jacob.jun.pan@linux.intel.com
Link: http://lkml.kernel.org/n/tip-fvm1hgpq99jln6l0fbek68ik@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We use MP IRQs for SFI presented timer interrupts, we should
also set mp_bus_not_pci for MP_ISA_BUS so that pin_2_irq mapping
is correct.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Link: http://lkml.kernel.org/n/tip-8h3rc1igpp8ir94aas69qmhk@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using compile time NR_LEGACY_IRQS causes the wrong gsi-irq
mapping on non-PC platforms, such as Moorestown. This patch uses
legacy_pic abstraction to set the correct number of legacy
interrupts at runtime. For Moorestown, nr_legacy_irqs = 0. We
have 1:1 mapping for gsi-irq even within the legacy irq range.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Link: http://lkml.kernel.org/n/tip-kzvj4xp9tmicuoqoh2w05iay@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The only semantic difference is that we now hold a reference to the
neighbour and thus have to release it.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future the ipv4/ipv6 route gateway will take on two types
of values:
1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
the neighbour must be obtained using the destination address in
ipv4/ipv6 header as the lookup key.
2) Everything else, the actual nexthop route address.
So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: David S. Miller <davem@davemloft.net>
While hard to measure, reducing the number of possibly/likely
mis-predicted branches can generally be expected to be slightly
better.
Other than apparent at the first glance, this also doesn't grow
the function size (the alignment gap to the next function just
gets smaller).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4F218584020000780006F422@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While currently there doesn't appear to be any reachable in-tree
case where such large memory blocks may be passed to memcpy(),
we already had hit the problem in our Xen kernels. Just like
done recently for mmeset(), rather than working around it,
prevent others from falling into the same trap by fixing this
long standing limitation.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4F21846F020000780006F3FA@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Quite oddly, all of the arguments passed through from the top
level macros to the second level which didn't need parentheses
had them, while the only expression (involving a parameter)
needing them didn't.
Very recently I got bitten by the lack thereof when using
something like "array + index" for the first operand, with
"array" being an array more narrow than int.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4F2183A9020000780006F3E6@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Get rid of the TOP_PTE() macro as we now have proper accessor functions
instead. No one should be directly referencing the top pte table
anymore.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide get_top_pte() to complement set_top_pte(), moving the only
users of TOP_PTE to arch/arm/mm/mm.h.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of places establish a PTE in our top page table and
immediately flush the TLB. Rather than having this at every callsite,
provide an inline function for this purpose.
This changes some global tlb flushes to be local; each time we setup
one of these mappings, we always do it with preemption disabled which
would prevent us migrating to another CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mk_pte is provided to do this translation for us, so use it rather
than open-coding it in the copypage code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the TOP_PTE address definitions to one central place so that it's
easy to discover what they're being used for. This helps to ensure
that there are no overlaps.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we span a long area in a bitmap we could end up taking a lot of time
searching to the next free area if we're searching from the original
window_start, so advance window_start in order to make sure we don't do any
superficial searching. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btree_releasepage is a callback and can be passed unknown gfp flags and then
they may end up in kmem_cache_alloc called from alloc_extent_state, slab
allocator will BUG_ON when there is HIGHMEM or DMA32 flag set.
This may happen when btrfs is mounted from a loop device, which masks out
__GFP_IO flag. The check in try_release_extent_state
3399 if ((mask & GFP_NOFS) == GFP_NOFS)
3400 mask = GFP_NOFS;
will not work and passes unfiltered flags further resulting in crash at
mm/slab.c:2963
[<000000000024ae4c>] cache_alloc_refill+0x3b4/0x5c8
[<000000000024c810>] kmem_cache_alloc+0x204/0x294
[<00000000001fd3c2>] mempool_alloc+0x52/0x170
[<000003c000ced0b0>] alloc_extent_state+0x40/0xd4 [btrfs]
[<000003c000cee5ae>] __clear_extent_bit+0x38a/0x4cc [btrfs]
[<000003c000cee78c>] try_release_extent_state+0x9c/0xd4 [btrfs]
[<000003c000cc4c66>] btree_releasepage+0x7e/0xd0 [btrfs]
[<0000000000210d84>] shrink_page_list+0x6a0/0x724
[<0000000000211394>] shrink_inactive_list+0x230/0x578
[<0000000000211bb8>] shrink_list+0x6c/0x120
[<0000000000211e4e>] shrink_zone+0x1e2/0x228
[<0000000000211f24>] shrink_zones+0x90/0x254
[<0000000000213410>] do_try_to_free_pages+0xac/0x420
[<0000000000213ae0>] try_to_free_pages+0x13c/0x1b0
[<0000000000204e6c>] __alloc_pages_nodemask+0x5b4/0x9a8
[<00000000001fb04a>] grab_cache_page_write_begin+0x7e/0xe8
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we did sysbench test for inline files, enospc error happened easily though
there was lots of free disk space which could be allocated for new chunks.
Reproduce steps:
# mkfs.btrfs -b $((2 * 1024 * 1024 * 1024)) <test partition>
# mount <test partition> /mnt
# ulimit -n 102400
# cd /mnt
# sysbench --num-threads=1 --test=fileio --file-num=81920 \
> --file-total-size=80M --file-block-size=1K --file-io-mode=sync \
> --file-test-mode=seqwr prepare
# sysbench --num-threads=1 --test=fileio --file-num=81920 \
> --file-total-size=80M --file-block-size=1K --file-io-mode=sync \
> --file-test-mode=seqwr run
<soon later, BUG_ON() was triggered by enospc error>
The reason of this bug is:
Now, we can reserve space which is larger than the free space in the chunks if
we have enough free disk space which can be used for new chunks. By this way,
the space allocator should allocate a new chunk by force if there is no free
space in the free space cache. But there are two wrong checks which break this
operation.
One is
if (ret == -ENOSPC && num_bytes > min_alloc_size)
in btrfs_reserve_extent(), it is wrong, we should try to allocate a new chunk
even we fail to allocate free space by minimum allocable size.
The other is
if (space_info->force_alloc)
force = space_info->force_alloc;
in do_chunk_alloc(). It makes the allocator ignore CHUNK_ALLOC_FORCE If someone
sets ->force_alloc to CHUNK_ALLOC_LIMITED, and makes the enospc error happen.
Fix these two wrong checks. Especially the second one, we fix it by changing
the value of CHUNK_ALLOC_LIMITED and CHUNK_ALLOC_FORCE, and make
CHUNK_ALLOC_FORCE greater than CHUNK_ALLOC_LIMITED since CHUNK_ALLOC_FORCE has
higher priority. And if the value which is passed in by the caller is greater
than ->force_alloc, use the passed value.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
xfstests 218 complains that btrfs defrags a file partially:
After: 1
Write backwards sync, but contiguous - should defrag to 1 extent
Before: 10
-After: 1
+After: 2
To fix this, we need to set max_to_defrag count properly.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There have been 4 warnings on 32-bit build, they are herewith fixed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We specifically set window_start in the cluster struct to indicate where the
cluster starts in a bitmap, but we've been using min_start to indicate where
we're searching from. This is usually the start of the blockgroup, so
essentially means we're constantly searching from the start of any bitmap we
find, which completely negates all the trouble we go to in order to setup a
cluster. So start using window_start to make sure we actually use the area we
found. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
A user has encountered a NULL pointer kernel oops in btrfs when
encountering media errors. The problem has been identified
as an unhandled NULL pointer returned from find_get_page().
This modification simply checks for a NULL page, and returns
with an error if found (the extent_range_uptodate() function
returns 1 on errors).
After testing this patch, the user reported that the error with
the NULL pointer oops was solved. However, there is still a
remaining problem with a thread becoming stuck in
wait_on_page_locked(page) in the read_extent_buffer_pages(...)
function in extent_io.c
for (i = start_i; i < num_pages; i++) {
page = extent_buffer_page(eb, i);
wait_on_page_locked(page);
if (!PageUptodate(page))
ret = -EIO;
}
This patch leaves the issue with the locked page yet to be resolved.
Signed-off-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
wait_log_commit() and wait_for_writer() were using slightly different
conditions for deciding whether they should call schedule() and whether they
should continue in the wait loop. Thus it could happen that we busylooped when
the first condition was not true while the second one was. That is burning CPU
cycles needlessly and is deadly on UP machines...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We have only been checking for min_bytes available in bitmap entries, but we
won't successfully setup a bitmap cluster unless it has at least bytes in the
bitmap, so in the common case min_bytes is 4k and we want something like 2MB, so
if there are a bunch of bitmap entries with less than 2mb's in them, we'll
search all them anyway, which is suboptimal. Fix this check. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Added initialization with the declaration of ret. It isn't set later on the
switch-default branch (which should never be taken).
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>