In TTM world the pages for the graphic drivers are kept in three different
pools: write combined, uncached, and cached (write-back). When the pages
are used by the graphic driver the graphic adapter via its built in MMU
(or AGP) programs these pages in. The programming requires the virtual address
(from the graphic adapter perspective) and the physical address (either System RAM
or the memory on the card) which is obtained using the pci_map_* calls (which does the
virtual to physical - or bus address translation). During the graphic application's
"life" those pages can be shuffled around, swapped out to disk, moved from the
VRAM to System RAM or vice-versa. This all works with the existing TTM pool code
- except when we want to use the software IOTLB (SWIOTLB) code to "map" the physical
addresses to the graphic adapter MMU. We end up programming the bounce buffer's
physical address instead of the TTM pool memory's and get a non-worky driver.
There are two solutions:
1) using the DMA API to allocate pages that are screened by the DMA API, or
2) using the pci_sync_* calls to copy the pages from the bounce-buffer and back.
This patch fixes the issue by allocating pages using the DMA API. The second
is a viable option - but it has performance drawbacks and potential correctness
issues - think of the write cache page being bounced (SWIOTLB->TTM), the
WC is set on the TTM page and the copy from SWIOTLB not making it to the TTM
page until the page has been recycled in the pool (and used by another application).
The bounce buffer does not get activated often - only in cases where we have
a 32-bit capable card and we want to use a page that is allocated above the
4GB limit. The bounce buffer offers the solution of copying the contents
of that 4GB page to an location below 4GB and then back when the operation has been
completed (or vice-versa). This is done by using the 'pci_sync_*' calls.
Note: If you look carefully enough in the existing TTM page pool code you will
notice the GFP_DMA32 flag is used - which should guarantee that the provided page
is under 4GB. It certainly is the case, except this gets ignored in two cases:
- If user specifies 'swiotlb=force' which bounces _every_ page.
- If user is using a Xen's PV Linux guest (which uses the SWIOTLB and the
underlaying PFN's aren't necessarily under 4GB).
To not have this extra copying done the other option is to allocate the pages
using the DMA API so that there is not need to map the page and perform the
expensive 'pci_sync_*' calls.
This DMA API capable TTM pool requires for this the 'struct device' to
properly call the DMA API. It also has to track the virtual and bus address of
the page being handed out in case it ends up being swapped out or de-allocated -
to make sure it is de-allocated using the proper's 'struct device'.
Implementation wise the code keeps two lists: one that is attached to the
'struct device' (via the dev->dma_pools list) and a global one to be used when
the 'struct device' is unavailable (think shrinker code). The global list can
iterate over all of the 'struct device' and its associated dma_pool. The list
in dev->dma_pools can only iterate the device's dma_pool.
/[struct device_pool]\
/---------------------------------------------------| dev |
/ +-------| dma_pool |
/-----+------\ / \--------------------/
|struct device| /-->[struct dma_pool for WC]</ /[struct device_pool]\
| dma_pools +----+ /-| dev |
| ... | \--->[struct dma_pool for uncached]<-/--| dma_pool |
\-----+------/ / \--------------------/
\----------------------------------------------/
[Two pools associated with the device (WC and UC), and the parallel list
containing the 'struct dev' and 'struct dma_pool' entries]
The maximum amount of dma pools a device can have is six: write-combined,
uncached, and cached; then there are the DMA32 variants which are:
write-combined dma32, uncached dma32, and cached dma32.
Currently this code only gets activated when any variant of the SWIOTLB IOMMU
code is running (Intel without VT-d, AMD without GART, IBM Calgary and Xen PV
with PCI devices).
Tested-by: Michel Dänzer <michel@daenzer.net>
[v1: Using swiotlb_nr_tbl instead of swiotlb_enabled]
[v2: Major overhaul - added 'inuse_list' to seperate used from inuse and reorder
the order of lists to get better performance.]
[v3: Added comments/and some logic based on review, Added Jerome tag]
[v4: rebase on top of ttm_tt & ttm_backend merge]
[v5: rebase on top of ttm memory accounting overhaul]
[v6: New rebase on top of more memory accouting changes]
[v7: well rebase on top of no memory accounting changes]
[v8: make sure pages list is initialized empty]
[v9: calll ttm_mem_global_free_page in unpopulate for accurate accountg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Move the page allocation and freeing to driver callback and
provide ttm code helper function for those.
Most intrusive change, is the fact that we now only fully
populate an object this simplify some of code designed around
the page fault design.
V2 Rebase on top of memory accounting overhaul
V3 New rebase on top of more memory accouting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
ttm_backend will only exist with a ttm_tt, and ttm_tt
will only be of interest when bound to a backend. Merge them
to avoid code and data duplication.
V2 Rebase on top of memory accounting overhaul
V3 Rebase on top of more memory accounting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V5 make sure ttm is unbound before destroying, change commit
message on suggestion from Tormod Volden
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Use the ttm_tt pages array for pages allocations, move the list
unwinding into the page allocation functions.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
On failure we need to make sure the page we free has wb cache
attribute. Do this pas call the proper ttm page helper function.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
This field is not use by any of the driver just drop it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Split btw highmem and lowmem page was rendered useless by the
pool code. Remove it. Note further cleanup would change the
ttm page allocation helper to actualy take an array instead
of relying on list this could drasticly reduce the number of
function call in the common case of allocation whole buffer.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
The expiry function compares the timer against current time and does
not expire the timer when the expiry time is >= now. That's wrong. If
the timer is set for now, then it must expire.
Make the condition expiry > now for breaking out the loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: stable@kernel.org
The clock_getres() function must return the resolution in the timespec
argument and return 0 for success.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: stable@kernel.org
Cc: Richard Cochran <richard.cochran@omicron.at>
This was never use in none of the driver, properly using userspace
page for bo would need more code (vma interaction mostly). Removing
this dead code in preparation of ttm_tt & backend merge.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
As a mechanism to detect whether SWIOTLB is enabled or not.
We also fix the spelling - it was swioltb instead of
swiotlb.
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[v1: Ripped out swiotlb_enabled]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we fail to read the IRQ type from the interrupt controller don't
fail, just assume a value and solider on - we may fail later when we try
to request the IRQ but it's possible we'll succeed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Document the device tree binding for the WM8903 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the WM8903 is hooked up to an interrupt, set the irq_active_low flag
in the default platform data based on the IRQ's IRQ_TYPE. Map IRQ_TYPE_NONE
(a lack of explicit configuration/restriction) to irq_active_low = false;
the previous default.
This code is mainly added to support device tree interrupt bindings,
although will work perfectly well in a non device tree system too.
Any interrupt controller that supports only a single IRQ_TYPE could
set each IRQ's type based on that restriction. This applies equally
with and without device tree. To cater for interrupt controllers
that don't do this, for which irqd_get_trigger_type() will return
IRQ_TYPE_NONE, the platform data irq_active_low field may be used
in systems that don't use device tree.
With device tree, every IRQ must have some IRQ_TYPE set.
Controllers that support DT and multiple IRQ_TYPEs must define the
interrupts property (as used in interrupt source nodes) such that it
defines the IRQ_TYPE to use. When the core DT setup code initializes
wm8903->irq, the interrupts property will be parsed, and as a side-
effect, set the IRQ's IRQ_TYPE for the WM8903 probe() function to read.
Controllers that support DT and a single IRQ_TYPE could arrange to
set the IRQ_TYPE somehow during their initialization, or hard-code
it during the processing of the child interrupts property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pdata pointer is now always valid. Remove any conditions that check
its validity.
This patch is mostly just removing an indentation level. One variable had
to be moved due to the removal of a scope, and one comment was split into
two. Viewing the patch with git show/diff -b will show that it's actually
very small.
Note that WM8903_MIC_BIAS_CONTROL_0 is now written unconditionally,
whereas it used to be written only if pdata was supplied. Since
defpdata.micdet_cfg = 0, this unconditional write simply echos the HW
defaults in the case where pdata is not supplied.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We currently fail to build on CONFIG_X86_INTEL_MID=y and
CONFIG_X86_MRST unset.
We could build all the bits to make generic MID work if you
picked MID platform alone but that's really silly. Instead use
select and two variables.
This looks a bit daft right now but once we add a Medfield
selection it'll start to look a good deal more sensible.
Reported-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge topic branch with some of Jesse's cleanups, the save/restore hooks
were being used by GMA500 so we can't just drop them.
* drm-cleanups-jbarnes:
drm: remove some potentially dangerous DRM_ERRORs
drm: document the drm_mode_config structure
drm: document the drm_mode_group structure
drm: document and cleanup drm_mode_config_funcs
drm: document drm_mode_set structure
drm: remove unused fields in drm_connector and document the rest
drm: add drm_encoder comments
drm: add comments for drm_encoder_funcs
drm: fix comments for drm_crtc struct
drm: remove unused connector_count field from drm_display_mode
Each of these error messages can be caused by a broken or malicious
userspace wanting to spam the dmesg with useless info. They're really
not worthy of DRM_DEBUG statements either; those are generally only
useful during bringup of new hardware or versions, and ought to be
removed before going upstream anyway.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Including a comment about what the locks are for.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is actually a core structure with a big future ahead of it. Make
it a little less mysterious.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just fix the wrapping mostly.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a core mode setting structure that deserves a little verbiage.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We never used initial_x/y or the force_encoder_id, so drop those fields
and proide a basic description of the others.
Really, the ELD bits belong in drm_display_info rather than directly in
the connector, but that's a separate cleanup.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just some basic comments about the place and function of the structure
and fields.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just basic verbiage.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove stale entries and update with the latest stuff.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allow userspace applications to do more parameter setting by providing a
more complete stub DMA driver specifying a wildcard set of formats and
channels and essentially random values for the DMA parameters. This is
required for useful runtime operation of the dummy DMA driver until we
are able to figure out how to power up links and do hw_params() from DAPM.
Sending to stable as without this the dummy driver is not terribly
useful.
Reported-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Tested-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This merges a topic branch containing patches from Alan for the GMA500 driver.
* drm-gma500-alancox:
gma500: Oaktrail BIOS handling
gma500: Fix oaktrail probing part 1
gma500: Be smarter about layout
gma500: gtt based hardware scrolling console
gma500: frame buffer locking
gma500: Fix backlight crash
gma500: kill bogus code
gma500: Convert spaces to tabs in accel_2d.c.
gma500: do a pass over the FIXME tags
gma500: Add VBLANK support for Poulsbo hardware
gma500: Don't enable MSI on Poulsbo
gma500: Only register interrupt handler for poulsbo hardware
gma500: kill virtual mapping support
gma500: Move the API
gma500: kill off NUM_PIPE define
gma500: Rename the ioctls to avoid clashing with the legacy drivers
drm/gma500: begin pruning dead bits of API
Now that we pull the right BIOS data out of the hat we need to use it when
doing our panel setup.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Oaktrail platform does not use the GCT/VBT format that is used by the
Moorestowm (non PC legacy) equivalent device. It uses the BIOS tables which
means an opregion and the like.
The current code uses the wrong table which breaks things like the Fujitsu
q550 tablets. Fix the table usage as a first step.
The problem was found and diagnosed by Chia-I Wu
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we can't fit a page aligned display stride then it's not the end of the
world for a normal font, so try half a page and work down sizes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for GTT based scrolling. Instead of pushing bits around we simply
use the GTT to change the mappings. This provides us with a very fast way to
scroll the display providing we have enough memory to allocate on 4K line
boundaries. In practice this seems to be the case except for very big displays
such as HDMI, and the usual configurations are netbooks/tablets.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we are the console then a printk can hit us with a spin lock held (and
in fact the kernel will do its best to take the console printing lock).
In that case we cannot politely sleep when synching after an accelerated op
but must behave obnoxiously to be sure of getting the bits out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initial changes to get backlight behaviour we want and to fix backlight crashes
on suspend/resume paths.
[Note: on some boxes this will now produce a warning about the backlight, this
isn't a regression it's an unfixed but non harmful case I still need to nail]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
During the power split ups and work a chunk of code escaped into the
Poulsbo code path which it isn't for. On some devices such as the Dell
mini-10 this causes problems.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert the spaces within the accel_2d.c file to tabs in order to comply
with the coding style of the kernel.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
[Trimmed to subset relevant to current tree]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chipset reports MSI capabilities for Poulsbo even though it isn't really there.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First step in adding proper irq handling. We'll start with poulsbo support so
make sure other chips don't touch drm_irq_install().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This isn't actually usable - we simply don't have the vmap space on a 32bit
system to do this stunt. Instead we will rely on the low level drivers
limiting the console resolution as before.
The real fix is for someone to write a page table aware version of the
framebuffer console blit functions. Good university student project
perhaps..
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Quiets the sparse noise:
warning: symbol 'gfs2_initxattrs' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
We don't want this external in case someone adds more to the hardware. We
want it out of the ABI.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>