Alek Du reported that the code erroneously applies time to jiffies
conversions twice to the t1 and t2 values. In normal use on a modem link
this cases no visible problem but on a slower link it will break as with
HZ=1000 as is typical we are running t1/t2 ten times too fast.
Alek's original patch removed the conversion from the timer setting but we
in fact have to be more careful as the contents of t1/t2 are visible via
the device API and we thus need to correct the constants.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Kernel hangs occasionally during boot after "Calibrating delay loop..".
This is caused by the c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable the timer and hang later.
The false return happens because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits for the timer changes to
propagate to the cp0 cause register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb instructions and can take
as little as a few clock ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not working. This fix uses up
to a max number of cycle counter ticks for the delay and uses
back_to_back_c0_hazard() instead of irq_disable_hazard() to handle the
hazard condition between cp0 writes and cp0 reads.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The driver used NET_IP_ALIGN to remove some additional padding inside of
the rx_fixup function. On many architectures NET_IP_ALIGN defaults to 2
which removed the correct amount of bytes.
On MCORE2-machines commit ea812ca1b0
introduces a change which sets NET_IP_ALIGN to 0 by default. Which
triggered the bug on these machines.
This fix introduces a new RXW_PADDING define and uses this instead of
NET_IP_ALIGN. The name was taken from the original SMSC7500 driver which
is provided by SMSC.
Signed-off-by: Nico Erfurth <ne@erfurth.eu>
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4291 Section 2.7 says Multicast addresses must not be used as source
addresses in IPv6 packets - drop them on input so we don't process the
packet further.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Reported-and-Tested-by: Kumar Sanghvi <divinekumar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_MSM_SCM uses the smc instruction, which with some
toolchains requires a ".arch_extension" directive.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
In the recent usb-audio driver, the initialization of volume ranges
may be delayed when the device doesn't respond well at the probing time.
But the volume quirks for certain devices are applied only in
mixer_ctl_feature_info() thus only at the very first probe and will be
missing when the volume range is initialized later.
This patch moves the volume quirk code to be always called from the
volume-range extraction (get_min_max()), so that the quirks are properly
applied in the later init time.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ensure ioend->io_error gets propagated back to e.g. AIO completions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
The log item ops aren't nessecarily the biggest exploit vector, but marking
them const is easy enough. Also remove the unused xfs_item_ops_t typedef
while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Fixes a possible memory corruption when the link is larger than
MAXPATHLEN and XFS_DEBUG is not enabled. This also remove the
S_ISLNK assert, since the inode mode is checked previously in
xfs_readlink_by_handle() and via VFS.
Updated to address concerns raised by Ben Hutchings about the loose
attention paid to 32- vs 64-bit values, and the lack of handling a
potentially negative pathlen value:
- Changed type of "pathlen" to be xfs_fsize_t, to match that of
ip->i_d.di_size
- Added checking for a negative pathlen to the too-long pathlen
test, and generalized the message that gets reported in that case
to reflect the change
As a result, if a negative pathlen were encountered, this function
would return EFSCORRUPTED (and would fail an assertion for a debug
build)--just as would a too-long pathlen.
Signed-off-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Now that they're used in the same way, it's a little simpler to put open
and lock owners in the same hash table, and I can't see a reason not to.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fix compile failure in drivers/iommu/omap-iommu-debug.c
because of missing module.h include.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
WM9081_BIAS_ENA is the bit[1] of WM9081_BIAS_CONTROL_1 register (05h).
Current code incorrectly write it to WM9081_VMID_CONTROL(04h) register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
VMID Divider Enable and Select is controlled by BIT[2:1] of WM9081_VMID_CONTROL
register (04h).
Current code reads wrong register (WM9081_BIAS_CONTROL_1) for setting
VMID 2*240k.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Arjan would like to make struct file_operations const, but
mce-inject directly writes to the mce_chrdev_ops to install its
write handler. In an ideal world mce-inject would have its own
character device, but we have a sizable legacy of test scripts
that hardwire "/dev/mcelog", so it would be painful to switch to
a separate device now. Instead, this patch switches to a stub
function in the mce code, with a registration helper that
mce-inject can call when it is loaded.
Note that this would also allow for a sane process to allow
mce-inject to be unloaded again (with an unregister function,
and appropriate module_{get,put}() calls), but that is left for
potential future patches.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4eb2e1971326651a3b@agluck-desktop.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds address type info (typically BR/EDR vs LE) to management
messages that need this. This also ensures conformance to the latest
management API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
BR/EDR link keys have their own commands and events (separate from SMP)
and the remove_keys command (previously remove_key) removes keys of any
kind for the specified remote address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We should return a ENETDOWN status response if the adapter is powered
off (i.e. the HCI_UP flag isn't set).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There's no need to deal with mgmt_pending_cmd when blocking and
unblocking devices since these actions are synchronous.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The power off code doesn't need to use its own custom timer since the
delayed_work API provides the exact same functionality.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A proper mgmt_command_status should be returned to user-space if either
discoverable or connectable enabling fails.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Based on the revised mgmt API set_discoverable has a timeout parameter
to specify how long the adapter will remain discoverable. A value of 0
means "indefinitively".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
By using periodic inquiry command we're not able to detect correctly
when the controller has started inquiry.
Today we have this workaround in inquiry result event handler
to set the HCI_INQUIRY flag when it sees the first inquiry result
event. This workaround isn't enough because the device may be
performing an inquiry but the HCI_INQUIRY flag is not set. For
instance, if there is no device in range, no inquiry result event
is generated, consequently, the HCI_INQUIRY flags isn't set when
it should so.
We rely on HCI_INQUIRY flag to implement the discovery procedure
properly. So, as we aren't able to clear/set the HCI_INQUIRY flag
in a reliable manner, periodic inquiry events shouldn't change
the HCI_INQUIRY flag.
Thus, due to that issue and in order to keep compatibility with
userspace, periodic inquiry events shouldn't send mgmt discovering
events.
In future, we might track if periodic inquiry is enabled or not.
By tracking this state we'll be able to do some improvements in
Discovery such as failing MGMT_OP_START_DISCOVERY command in case
periodic inquiry is on. We can also send no mgmt_device_found
event if periodic inquiry is on.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to hci_core to cancel an ongoing inquiry.
According to the Bluetooth spec, the inquiry cancel command should
only be issued after the inquiry command has been issued, a command
status event has been received for the inquiry command, and before
the inquiry complete event occurs.
As HCI_INQUIRY flag is only set just after an inquiry command status
event occurs and it is cleared just after an inquiry complete event
occurs, the inquiry cancel command should be issued only if HCI_INQUIRY
flag is set.
Additionally, cancel inquiry related code from stop_discovery() were
replaced by a hci_cancel_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to hci_core to carry out inquiry.
All inquiry code from start_discovery() were replaced by a
hci_do_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Users probably don't care about the specific compression algorithm and
we might want to use a different algorithm (snappy being the one I'm
thinking of right now) so update the public interface to have a more
generic name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This initial conversion just moves the register init, regulator acquisition
and device verification out to the I2C probe(). Movement of other parts of
the driver like the GPIO and beep generation code will follow.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the WM8996 driver is using the regmap API for register I/O we no
longer need the ASoC card to be active in order to interact with the chip.
In order to be more idiomatic for Linux move most of the existing probe()
function out into the I2C probe() function prior to registration with ASoC.
The IRQ and GPIO init will be moved separately as these are slightly more
involved.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A potentially uninitialised variable, some unreachable code,
and the main part of this, fixing the error path in the
unlink function.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
wl1271_suspend/resume() accessed the wrong struct and not wl1271
which caused it to think that wow was enabled when it wasn't.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Idle changes are currently handled per hardware.
However, some operations should be done only per-interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The merge commit "526b264 Merge branch 'imx/cleanup' into imx/devel"
left a duplicated mx28_add_mxs_mmc() call, which causes the problem
below during boot.
kobject_add_internal failed for mxs-mmc.1 with -EEXIST, don't try
to register things with the same name in the same directory.
The patch removes this leftover and also change mmc0 adding to align
with mmc1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
If the skb contains the NO_CCK flag, use the p2p rate index
(which contains only the OFDM rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the TX rate of probe requests during scanning according to the
no_cck flag in the scan request struct.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move all USB radio devices to the top of the list and move all ISA
devices to a separate menu.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for pointing this
out to me.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>