The (*detach) function, daq700_detach() is now a simple wrapper around
comedi_pcmcia_disable(). Just use comedi_pcmcia_disable() directly for
the (*detach).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
This driver does not use interrupts and is not an audio device,
remove CONF_ENABLE_IRQ and CONF_AUTO_AUDIO from the link->config_flags.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
This driver does not use interrupts so remove CONF_ENABLE_IRQ from
the link->config_flags.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The (*detach) function, das16cs_detach() is a simple wrapper around
comedi_pcmcia_disable(). Just use comedi_pcmcia_disable() directly
for the (*detach).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pcmcia_request_irq() instead of request_irq() to request the
irq for the PCMCIA device. This allows the PCMCIA core to clean
up the registration in pcmcia_disable_device().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the comedi_pcmcia_{enable,disable} helpers to enable/disable
the PCMCIA device.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce some helper functions to enable/disable the PCMCIA device.
This will allow removing some of the boilerplate code in the comedi
PCMCIA drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we dynamically allocate them now, allow the system to call us up
to release them if it gets low on memory. Since these entries aren't
replaceable, only free ones that are expired or that are over the cap.
The the seeks value is set to '1' however to indicate that freeing the
these entries is low-cost.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's not sufficient to only clean the cache when requests come in. What
if we have a flurry of activity and then the server goes idle? Add a
workqueue job that will clean the cache every RC_EXPIRE period.
Care is taken to only run this when we expect to have entries expiring.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There's no need to keep entries around that we're declaring RC_NOCACHE.
Ditto if there's a problem with the entry.
With this change too, there's no need to test for RC_UNUSED in the
search function. If the entry's in the hash table then it's either
INPROG or DONE.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
With the change to dynamically allocate entries, the cache is never
disabled on the fly. Remove this flag.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The existing code keeps a fixed-size cache of 1024 entries. This is much
too small for a busy server, and wastes memory on an idle one. This
patch changes the code to dynamically allocate and free these cache
entries.
A cap on the number of entries is retained, but it's much larger than
the existing value and now scales with the amount of low memory in the
machine.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
...otherwise, we end up with the list ordering wrong. Currently, it's
not a problem since we skip RC_INPROG entries, but keeping the ordering
strict will be necessary for a later patch that adds a cache cleaner.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch addresses a long standing issue of the driver with the
mac80211 .flush() callback. Since implementing the .flush() callback
a number of issues have been fixed, but a WARN_ON_ONCE() was still
triggered because the timeout on the flush could still occur.
This patch changes the awkward design using msleep() into one using
a waitqueue. The waiting flush() context will kick the transmit dma
when it is idle and the timeout used waiting for the event is set
to 500 ms. Worst case there can be 64 frames outstanding for transmit
in the driver. At a rate of 1Mbps that would take 1.5 seconds assuming
MTU is 1500 bytes and ignoring retries. The WARN_ON_ONCE() is also
removed as this was put in to indicate the flush timeout as a reason
for the driver to stall. That was not happening since fixing endless
AMPDU retries with following upstream commit:
commit 85091fc0a7
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Feb 23 18:38:22 2012 +0100
brcm80211: smac: fix endless retry of A-MPDU transmissions
bugzilla: 42840 <https://bugzilla.kernel.org/show_bug.cgi?id=42840>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=799168>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=787649>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Camaleón <noelamac@gmail.com>
Cc: Milan Bouchet-Valat <nalimilan@club-internet.fr>
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unregisters the gpio chip before ssb gets unloaded.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unregisters the gpio chip before bcma gets unloaded.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel commits 41affd5 and 6539306 changed the locking in rtl_lps_leave()
from a spinlock to a mutex by doing the calls indirectly from a work queue
to reduce the time that interrupts were disabled. This change was fine for
most systems; however a scheduling while atomic bug was reported in
https://bugzilla.redhat.com/show_bug.cgi?id=903881. The backtrace indicates
that routine rtl_is_special(), which calls rtl_lps_leave() in three places
was entered in atomic context. These direct calls are replaced by putting a
request on the appropriate work queue.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Nathaniel Doherty <ntdoherty@gmail.com>
Cc: Nathaniel Doherty <ntdoherty@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return EINVAL from write if the size is larger than
allowed. Do this before allocating kernel memory for
the bogus size, which could lead to OOM.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Jana Saout <jana@saout.de>
Signed-off-by: David Teigland <teigland@redhat.com>
Pull x86 fixes from Ingo Molnar:
"Three small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up annoying warning
x86, doc: Boot protocol 2.12 is in 3.8
x86-64: Replace left over sti/cli in ia32 audit exit code
Pull scheduler fixes from Ingo Molnar:
"Three small fixlets"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix format string for 32-bit platforms
sched: Fix warning in kernel/sched/fair.c
sched/rt: Use root_domain of rt_rq not current processor
Pull perf fixes from Ingo Molnar:
"Three fixlets and two small (and low risk) hw-enablement changes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix event group context move
x86/perf: Add IvyBridge EP support
perf/x86: Fix P6 driver section warning
arch/x86/tools/insn_sanity.c: Identify source of messages
perf/x86: Enable Intel Lincroft/Penwell/Cloverview Atom support
Pull two small RCU fixlets from Ingo Molnar.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_nocb_poll an early_param instead of module_param
rcu: Prevent soft-lockup complaints about no-CBs CPUs
Print error message if requesting an interrupt fails.
Use int instead of unsigned for interrupts in case of error values
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exporting gpios over sysfs GPIO interface throws genirq
error messages, i.e. on an mpc5121 based board exporting
GPIO 5 triggers it:
# echo 229 > /sys/class/gpio/export
genirq: Setting trigger mode 0 for irq 44 failed
(mpc512x_irq_set_type+0x0/0x18c)
Similar error messages appear in the kernel boot log since the
board specifies GPIOs for matrix keypad and also SD Card write
protect and card detect GPIOs in its device tree. For all these
GPIOs there is an error message in the log.
The issue is triggered by setting the irq type to IRQ_TYPE_NONE
in the driver's irq_domain map function mpc8xxx_gpio_irq_map().
...
mpc8xxx_gpio_irq_map
irq_set_irq_type
__irq_set_trigger
__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio
irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback
is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these
functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the
flow_type argument. This return value triggers the observed error
message in __irq_set_trigger(). Modifying these callbacks to not
return an error in IRQ_TYPE_NONE case doesn't make any sense to me.
The line setting IRQ_TYPE_NONE type has been originally added by
commit 345e5c8a "powerpc: Add interrupt support to mpc8xxx_gpio".
At this time set_irq_type() checked its type argument and returned 0
if the type argument didn't specify any meaningful type in its type
sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this
line was a nop and I wonder what was the point of adding it.
Remove IRQ_TYPE_NONE setting in the irq_domain mapping function.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_reserve() has no user and stands in the way of the removal of
the static gpio_desc[] array. Remove this function as well as the now
unneeded RESERVED flag of struct gpio_desc.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO address space reservation during early platform initialization is
not needed anymore for Tosa. Remove the calls to gpiochip_reserve()
which is due to be removed.
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The uses of trace_clock_local() are dead code when CONFIG_RCU_TRACE=n,
but some compilers might nevertheless generate code calling this function.
This commit therefore ensures that trace_clock_local() is invoked only
when CONFIG_RCU_TRACE=y.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ext4 block allocator only maintains buddy bitmaps for chunks which
are less than or equal to one quarter of a block group. That is, for
a file aystem with a 1k blocksize, and where the number of blocks in a
block group is 8192 blocks, the largest chunk size tracked by buddy
bitmaps is 2048 blocks.
For a file system with a 4k blocksize, and where the number of blocks
in a block group is 32768 blocks, the largest chunk size tracked by
buddy bitmaps is 8192 blocks.
To work around this code, mballoc.c before this commit would truncate
allocation requests to the number of blocks in a block group minus 10.
Why 10? Aside from being a completely arbitrary number, it avoids
block allocation to be a power of two larger than 25% of the block
group. If you try to explicitly fallocate 50% of the block group
size, this will demonstrate the problem; the block allocation code
will scan the all of the blocks in the file system with cr==0 (since
the request is for a natural power of two), but then completely fail
for all blocks groups, since the buddy bitmaps don't track chunk sizes
of 50% of the block group.
To fix this, in these we use ext4_mb_complex_scan_group() instead of
ext4_mb_simple_scan_group().
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger@dilger.ca>
In case port is leaving the team, set the option "activeport" as changed
so the change can be properly propagated to userspace
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In team_port_del(), there is need to be do all the cleanup related
things first and netlink event notifiers should be called after that.
This fixes two problems:
team carrier is now correctly set (port is removed from list first)
mode can set option as changed in .port_leave op
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Essentially do the same thing with port list as with option list.
Multipart netlink message.
Side effect is that port event message can send port which is not longer
in team->port_list.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the regmap API to use asynchronous I/O where supported to minimise
the delay between transfers, reducing firmware download times.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow drivers to take advantage of any support the underlying transports
may have for pipelining data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/cJO
-----END PGP SIGNATURE-----
Merge tag 'async' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-adsp
regmap: Add async I/O support
Allow drivers to take advantage of any support the underlying transports
may have for pipelining data.
If the previous CPU is cache affine and idle, select it.
The current implementation simply traverses the sd_llc domain,
taking the first idle CPU encountered, which walks buddy pairs
hand in hand over the package, inflicting excruciating pain.
1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1359371965.5783.127.camel@marge.simpson.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch simplifies the code of XGISetModeNew by reordering the
if/else if/case conditions when both branches are doing exactly the
same.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two functions share the same code except one line - thus we can
simply merge them and add a parameter to switch between both variants.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since data can only be 0x0000, 0x0035 or 0x0048 we can simply skip the
bit shifting and masking as data & 0xFF is always equal to data and
data & 0xFF00 is always 0.
So we simply use data and 0 directly and save the assignment.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of subtracting one and then assign a different name and add 1
again we simply use HDE directly. HDE wasn't used directly before, so no
change in functionality.
Same applies to VDE.
-> now we can remove the variable with the very descriptive name E ;)
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to use this switch-case here for a simple two case
if-else.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since SR[0] in the (readonly) XGI330_StandTable is always 0x01 we can
skip or'ing with 0x01 and make the code simpler by removing the if
statements.
Since this function is the only user of the XGI330_StandTable we can
also include the unconditional |= 0x20 into the input data and move the
assignment to SR1 into the loop, which I prefer to start at 0.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warning:
drivers/staging/xgifb/XGI_main_26.c: warning: variable 'ret' is
used uninitialized whenever 'if' condition:
if (xgifb_info->mode_idx < 0) {
evaluates to true.
drivers/staging/xgifb/XGI_main_26.c:
note: uninitialized use occurs here
return ret;
This patch initializes the variable in this case.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mttr field must be declared as signed int (as in every other fb
driver) for the mttr functions to work properly.
Moreover the value should be initialized with -1.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some comparisons that always evaluate to false since
xoffset and yoffset are defined as __u32 in fb_var_screeninfo in
include/linux/fb.h and thus can never be negative.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
