The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We may not be able to fix a bad block if:
- the array is degraded
- the over-write fails.
In these cases we currently eject the device, but we should
record a bad block if possible.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 58c54fcca3
md/raid10: handle further errors during fix_read_error better.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 43220aa0f2
md/raid5: fix a hang on device failure.
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
- Fixes to new ocrdma driver
- Typo in test in CMA
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJP5wISAAoJEENa44ZhAt0hWzAQAIV1qnXTz+HDXzz8MLTX8wR0
6uUAcGxuP1PXB4K+DmYc7Ht0FnvJN0E9KN7cCDo20XbZU9NzXkqP36WL3fWt5+34
9YKQYK14Rbi65ex+UwbASnyZ35iuNjPSVnnnEWMAoE3ZmEXWdM9FzIX41xav+FTy
Lw0qIVO28d6Rx9LiODnNgbDqqyPzgqmam6SQszcfDwm+PqgcI/RaI/578GY+88qA
+qofgDpL5rnzyWa2GMIGlbB21xKlqlhF3GuSSp5hHmDCaiNtfS0KsyHE+ys6r1UC
uLKkBxlXngPF//DWFPUVVwXLHSHgtQ7qfHbk2kUqZjhrt/Famdju16q5oRSLiVrW
MoilOEMzbt0AaRn2tEQ4srXHvhNnHkxQsPlSZ+alMWRDZS1jf4ESMOj+V+4gUUUQ
+xYhyLge3GBUE8qt+zerbmLqRcyG6bF3HHMGFKJZrh3up++yZgZF/E5UXFTLYOv5
6j9sG+dELFgtAhbC13ysvj5IyiVrFl3oh7Ynf2q5/Fyo2yPtde/hk+TGzXwRFOQg
WF9SjnQsM3LsXhSX0D30kcjE76pCAcy6SyhE5FKA+mumyf7HG+UC+1lo2bUfNqO0
HAXcgsc7wGXoOvBO1YOCmpUTyWrCQT3OikltDibnWdoUYpfaYFAiWJKdtLA0HylK
3QJBh6/0/QGS5WhKr0KD
=LFia
-----END PGP SIGNATURE-----
Merge tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- Fixes to new ocrdma driver
- Typo in test in CMA
* tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: QP type check on received REQs should be AND not OR
RDMA/ocrdma: Fix off by one in ocrdma_query_gid()
RDMA/ocrdma: Fixed RQ error CQE polling
RDMA/ocrdma: Correct queue SGE calculation
RDMA/ocrdma: Correct reported max queue sizes
RDMA/ocrdma: Fixed GID table for vlan and events
Pull drm fixes from Dave Airlie:
"Nothing major in here, one radeon SI fix for tiling, and one uninit
var fix, two minor header file fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: drop comment about this header being autogenerated.
drm/edid: don't return stack garbage from supports_rb
vga_switcheroo: Add include guard
drm/radeon: SI tiling fixes for display
Two minor fixes in emc2103 and applesmc drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kDRE
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two minor fixes in emc2103 and applesmc drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc2103) Fix use of an uninitilized variable in error case
hwmon: (applesmc) Limit key length in warning messages
We need to initialize this to false, because the is_rb callback only
ever sets it to true.
Noticed while reading through the code.
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes in pl330 and imx-sdma drivers."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
DMA: PL330: Fix racy mutex unlock
DMA: PL330: Add missing static storage class specifier
dma: imx-sdma: buf_tail should be initialize in prepare function
dmaengine: pl330: dont complete descriptor for cyclic dma
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a number of small fixes for the drivers/staging tree, as well as iio
and pstore drivers (which came from the staging tree in the 3.5-rc1 merge).
All of these are tiny, but resolve issues that people have been reporting.
There's also a documentation update to reflect what the iio drivers really are
doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNeAACgkQMUfUDdst+ynNVwCdHCj6smC2JUbvN34gACNrpsYY
WggAoJzQn9mQhwq0pa/ZTpaUOvCFZ39L
=hDkC
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a number of small fixes for the drivers/staging tree, as well
as iio and pstore drivers (which came from the staging tree in the
3.5-rc1 merge). All of these are tiny, but resolve issues that people
have been reporting.
There's also a documentation update to reflect what the iio drivers
really are doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB IDs
staging: gdm72xx: Release netlink socket properly
iio: drop wrong reference from Kconfig
pstore/inode: Make pstore_fill_super() static
pstore/ram: Should zap persistent zone on unlink
pstore/ram_core: Factor persistent_ram_zap() out of post_init()
pstore/ram_core: Do not reset restored zone's position and size
pstore/ram: Should update old dmesg buffer before reading
staging:iio:ad7298: Fix linker error due to missing IIO kfifo buffer
Revert "staging: usbip: bugfix for stack corruption on 64-bit architectures"
staging: usbip: bugfix for stack corruption on 64-bit architectures
staging/comedi: fix build for USB not enabled
staging: omapdrm: fix crash when freeing bad fb
staging:iio:ad7606: Re-add missing scale attribute
iio: Fix potential use after free
staging:iio: remove num_interrupt_lines from documentation
iio: documentation: Add out_altvoltage and friends
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNGgACgkQMUfUDdst+ymmPwCeLxWcEx3UE0pyhwssITArJZz3
WFIAmgPHM66lgXioLxR3swCib9FFo+Xp
=hIWT
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc tree updates from Greg Kroah-Hartman:
"Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: mei: set WDIOF_ALARMONLY on mei watchdog
misc: mei: Disable MSI when IRQ registration fails
misc: mei: fix stalled read
misc: mei: unregister misc device in pci_remove function
misc: mei: set IRQF_ONESHOT for msi request_threaded_irq
Here are 3 patches resolving a boot regression (the mop500 fix), a build
warning fix, and a kernel-doc fix. All tiny, but should go into the
final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNosACgkQMUfUDdst+ykedgCeLhpFrq5dI19tbhEmCroFs4sx
f+4An29dz2bGkjeViDNkmaBC7msPzLNc
=EBge
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the correct union for getting the tiling info
- Properly init the PIPE_CONFIG field for SI
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull ARM fixes from Russell King:
"This includes three MMCI changes - one to fix up the wrong version of
the DT support patch which was merged, and two to make deferred
probing work. It also includes a fix to the OMAP SPI driver which is
causing a boot time warning.
The remainder are very minor ARM fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
SPI: fix over-eager devm_xxx() conversion
ARM: 7427/1: mmc: mmci: Defer probe() in case of yet uninitialized GPIOs
ARM: 7426/1: mmc: mmci: Remove wrong error handling of gpio 0
ARM: 7425/1: extable: ensure fixup entries are 4-byte aligned
ARM: 7421/1: bpf_jit: BPF_S_ANC_ALU_XOR_X support
ARM: 7423/1: kprobes: run t32_simulate_ldr_literal() without insn slot
ARM: 7422/1: mmc: mmci: Allocate platform memory during Device Tree boot
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zNxH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull two pinctrl fixes from Linus Walleij:
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: document Alt-C glitch
pinctrl: mxs: Use kfree to fix build error
Change || check to the intended && when checking the QP type in a
received connection request against the listening endpoint.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant that
the device tree code had apparently never actually been run against the
upstream device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NS0T
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant
that the device tree code had apparently never actually been run
against the upstream device tree."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Change db8500-prcmu match names to reflect Device Tree
regulator: Change ab8500 match names to reflect Device Tree
regulator: Fix the s5m8767a problem of the division by null
extcon_dev_unregister(info->edev) doest not free info->edev, we need to call
kfree(info->edev) here.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing platform_set_drvdata() in gpio_extcon_probe(), otherwise calling
platform_get_drvdata in gpio_extcon_remove() returns NULL.
Also add missing free_irq call in gpio_extcon_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the index of "Dock-desk" and "Dock-card" are the same.
Thus the latter one overrides the first one.
Then we have problem when calling extcon_find_cable_index() because
edev->supported_cable[7] only matches "Dock-card".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull EDAC fixes from Mauro Carvalho Chehab.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: Do alignment logic properly in edac_align_ptr()
mpc85xx_edac: fix error: too few arguments to function 'edac_mc_alloc'
edac: fix the error about memory type detection on SandyBridge
edac: avoid mce decoding crash after edac driver unloaded
Pull a crypto fix from Herbert Xu:
"This push fixes another bug in the atmel-rng that made it produce
completely useless output."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: atmel-rng - fix data valid check
Fix:
emc2103.c: In function set_pwm_enable:
emc2103.c:463:12: warning: conf_reg may be used uninitialized in this function
by checking the return value from read_u8_from_i2c(). This fixes a real problem,
as conf_reg is really uninitialized if read_u8_from_i2c returns an error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Key lookups may call read_smc() with a fixed-length key string,
and if the lookup fails, trailing stack content may appear in the
kernel log. Fixed with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
1a77b127ae (OMAP : SPI : use devm_* functions) converted the SPI
device controller state to use devm_kzalloc(). Unfortunately, this
is used against an unbound struct device, which results in the
following when the device is bound to its driver:
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/drivers/base/dd.c:257 driver_probe_device+0x78/0x21c()
Modules linked in:
Backtrace:
[<c0017d0c>] (dump_backtrace+0x0/0x10c) from [<c033e208>] (dump_stack+0x18/0x1c) r7:00000000 r6:c01ff28c r5:c040050c r4:00000101
[<c033e1f0>] (dump_stack+0x0/0x1c) from [<c00337ec>] (warn_slowpath_common+0x58/0x70)
[<c0033794>] (warn_slowpath_common+0x0/0x70) from [<c0033828>] (warn_slowpath_null+0x24/0x2c)
[<c0033804>] (warn_slowpath_null+0x0/0x2c) from [<c01ff28c>] (driver_probe_device+0x78/0x21c)
[<c01ff214>] (driver_probe_device+0x0/0x21c) from [<c01ff49c>] (__driver_attach+0x6c/0x90)
[<c01ff430>] (__driver_attach+0x0/0x90) from [<c01fda70>] (bus_for_each_dev+0x58/0x98)
[<c01fda18>] (bus_for_each_dev+0x0/0x98) from [<c01ff0f4>] (driver_attach+0x20/0x28)
[<c01ff0d4>] (driver_attach+0x0/0x28) from [<c01fe2f4>] (bus_add_driver+0xb4/0x230)
[<c01fe240>] (bus_add_driver+0x0/0x230) from [<c01ffb24>] (driver_register+0xac/0x138)
[<c01ffa78>] (driver_register+0x0/0x138) from [<c0215d4c>] (spi_register_driver+0x4c/0x60)
[<c0215d00>] (spi_register_driver+0x0/0x60) from [<c045414c>] (ks8851_init+0x14/0x1c)
[<c0454138>] (ks8851_init+0x0/0x1c) from [<c0008770>] (do_one_initcall+0x9c/0x164)
[<c00086d4>] (do_one_initcall+0x0/0x164) from [<c0436410>] (kernel_init+0x128/0x210)
[<c04362e8>] (kernel_init+0x0/0x210) from [<c0038754>] (do_exit+0x0/0x72c)
---[ end trace 4dcda79f5e89dd84 ]---
ks8851 spi1.0: message enable is 0
ks8851 spi1.0: eth0: revision 0, MAC 08:00:28:01:4d:c6, IRQ 194, has EEPROM
Fix this by partially reverting the original commit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the GPIOs used by the MMCI driver are not registered yet when the driver is
probe()d, they can't be used. This happens if the mmci driver is probed before
the respective GPIO controller (e.g. on the LPC32xx EA3250 board, the PCA9532
GPIO controller would be initialized via DT after mmci). Therefore, we defer
mmci in this case.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zero is a valid GPIO and shouldn't be handled as an error return code from
of_get_named_gpio(). It was a leftover from old code before getting
pdata->gpio_*() was modified.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This documentation comment existed in an earlier patch set for
GPIO consolidation, so I'm saving it for maintainability of the
code.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 0bf7481 (pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails)
introduced the following build error:
drivers/pinctrl/pinctrl-mxs.c:140:3: error: implicit declaration of function 'free'
Use kfree function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
