The conf structure is going to be exported to a file, so we should use
only well defined types. bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.
This commit adds a new file to debugfs to do that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics. The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The commit ba27ec66ff fixes the Kconfig of the
driver when built as module allowing to select/unselect
the PCI and Platform modules that are not anymore mutually
exclusive. This patch fixes and guarantees that the driver
builds on all the platforms w/ w/o PCI and when select/unselect
the two stmmac supports. In case of there are some problems
on both the configuration and the pci/pltf registration the
module_init will fail.
v2: set the CONFIG_STMMAC_PLATFORM enabled by default.
I've just noticed that this can actually help on
some configurations that don't enable any STMMAC
options by default (e.g. SPEAr).
v3: change printk level when do not register the driver.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dmaengine based NVIDIA's Tegra APB DMA driver.
This driver support the slave mode of data transfer from
peripheral to memory and vice versa.
The driver supports for the cyclic and non-cyclic mode
of data transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Also adds tps6586x_ldo0_voltages mapping table for LDO0, so we can remove the
hack in tps6586x_list_voltage() and convert it to regulator_list_voltage_table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's a little bit hard to read that the "else" case means id == PALMAS_REG_SMPS10.
if (id != PALMAS_REG_SMPS10){
do something for the cases id != PALMAS_REG_SMPS10;
} else {
do something for the case id == PALMAS_REG_SMPS10;
}
This patch changes above syntax to switch statement.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code actually clears more bits than PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For linear mappings, we can use below equation to get the voltage difference
between new_selector and old_selector:
abs(new_selector - old_selector) * rdev->desc->uV_step
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For fixed voltage, DA9030_LDO13 and DA9034_LDO5, the info->vol_reg is
DA9030_INVAL/DA9034_INVAL.
It does not make sense to read/write to DA9030_INVAL/DA9034_INVAL address.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixed voltage is a kind of linear mapping where n_voltages is 1.
This change allows [list|map]_voltage_linear to be used for fixed
voltage.
For fixed voltage, n_voltages is 1 and the only valid selector is 0.
Thus we actually don't care the uV_step setting.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly handle the case if the specified min_uV is less than the voltage given
by the lowest selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct mail address reference to a mail account which I actually read.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Feuerer <peter@piie.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Permanent MAC is wrongly supplied in create iface command. Call the
command with no MAC address and then MAC address should be later queried
and applied.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the bnx2x's ethtool interface to enable
control in the eee feature, as well as report statistic information
about it.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds energy efficient energy support (802.3az) to bnx2x
boards with 84833 phys (and sufficiently new BC and external FW).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added another error condition here, but if we were to hit it then
we need to unregister_netdev() before doing the free_netdev().
Otherwise we would hit the BUG_ON() in free_netdev():
BUG_ON(dev->reg_state != NETREG_UNREGISTERED);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer flavors of Yukon II use a different method for receive
checksum offload. This is indicated in the driver by the SKY2_HW_NEW_LE
flag. On these newer chips, the BMU_ENA_RX_CHKSUM should not be set.
The driver would get incorrectly toggle the bit, enabling the old
checksum logic on these chips and cause a BUG_ON() assertion. If
receive checksum was toggled via ethtool.
Reported-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an external 26 MHz crystal source.
[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.
[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]
[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).
[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: Orit Brayer <orit@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
PG2 requires 4 new parameters that to be passed to the PHY.
Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.
[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit "62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add the F3 PCI id of F15h, model 0x10 to pci_ids.h and to the amd_nb
code which generates the list of northbridges on an AMD box. Shorten
define name while at it so that it fits into pci_ids.h.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The iommu_shutdown callback is not initialized when the AMD
IOMMU driver runs in passthrough mode. Fix that by moving
the callback initialization before the check for
passthrough mode.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Fixes the following sparse warning:
drivers/dma/pl330.c:2542:5: warning: symbol 'add_desc' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This fix audio underrun issue. When SNDRV_PCM_TRIGGER_STOP
and SNDRV_PCM_TRIGGER_START, it calls prepare again. buf_tail
should be reset to zero.
So move buf_tail initialization into prepare function.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit eab2158558 ("dmaengine: pl330: dont complete descriptor for
cyclic dma") wrongly completes descriptor for cyclic dma, hence following
BUG_ON is still hit with cyclic DMA operations.
kernel BUG at drivers/dma/dmaengine.h:53!
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
This patch adds the support for D_CAN controller driver to the existing
C_CAN driver.
Bosch D_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be
obtained from: http://www.semiconductors.bosch.de/media/en/pdf/
ipmodules_1/can/d_can_users_manual_111.pdf
A new array is added for accessing the d_can registers, according to d_can
controller register space.
Current D_CAN implementation has following limitations, this is done
to avoid large changes to the C_CAN driver.
1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP
supports upto 32 message objects but in case of D_CAN we can configure
upto 128 message objects.
2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers.
3. These patches have been tested on little endian machine, there might
be some hidden endian-related issues due to the nature of the accesses
(32-bit registers accessed as 2 16-bit registers). However, I do not
have a big-endian D_CAN implementation to confirm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
c_can uses overlay structure for accessing c_can module registers.
With this kind of implementation it is difficult to add one more ip
which is similar to c_can in functionality but different register
offsets.
This patch changes the overlay structure implementation to an array
with register offset as index. This way we can overcome the above
limitation.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit "aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
The raw data reading process (ak8975_read_axis) sets the
single measurement mode to take a sample and once the
conversion is completed the device enters into power-down
mode automatically, therefore there is no need to enable
a flag for this to happen.
Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuse ROM data access mode is the only mode which does not
transition to power-down mode automatically.
As per the AK8975 data sheet, it is recomended to set the
power-down mode first before attempting to change into
another mode.
Signed-off-by: Leed Aguilar <leed.aguilar@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scnprint instead of snprintf, because snprintf returns the number of bytes
that would have been written to the buffer if there was enough space, and as a
result writing to buf[len-1] might cause a access beyond the buffers limits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>