There is one device supported by the driver which is not listed in the Kconfig
help test. This patch adds it. Also we are past the point were we can possible
fit all devices supported by the driver in the Kconfig entry title, so just list
the initial device that was supported by this driver and note that similar
devices are supported as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AD5662 is compatible to the AD5660, but uses an external
reference instead of an internal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not read back the value from the device, but we cache the value anyway so
we might as well return the cached value instead of an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devices supported by this drivers only have a single shift register, which
contains both the power down mode and the output sample. So writing the power
down mode and the output sample can be done by the same function. Call this
function prepare_write as it will prepare the spi message for a write. Also
introduce a small helper function which performs the whole write by calling the
chip the specific prepare function followed by a spi_sync.
The two power down bits are always placed ontop of the msb of the output sample,
so we can easily calculate their position by adding the channels shift to the
channels realbits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use extended channel attributes instead of raw sysfs files for the additional
channel attributes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three identical chip_info entries. Remove two of them and use the id
of the remaining entry for all three device table entries.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the chip_info's int_vref_mv field to decide whether a certain chip has a
internal reference or not. There is no need to check for individual chip ids.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unused "poll_work" field from the ad5446_state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently only write 16 bit in case where we should write 24 bit. The spi message
length is calculated from the channel storage_size, but since the storage size
is only 16 bit we end up with the wrong value for devices which have power down
bits and thus a register with 24 bit. Since each store function knows how many
bytes it has to write just use the spi_write function from there instead of
going through the hassle of manually preparing a spi_message and keeping buffers
in the state struct.
Another advantage of this patch is that it will make implementing support for
similar I2C based DACs much easier.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AD5620_LOAD and AD5446_LOAD are both 0, so all these three functions are
identical and we can replace them with only one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the powerdown mode bits and the sample value are stored in the same
register, so writing a sample while the device is powered down will clear the
power down bits. To avoid this only update the cached value when the device is
powered down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
----
v1 actually had a small bug in that it would still write to the device's
register when the sample was updated while the device was powered down. This was
not critical since it would send out the powerdown mode again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every i.MX ehci controller has a ahb and a ipg clock, so request
it on every SoC. Do not make a special case for the usb phy clock
of the i.MX51. Just request it but make it optional.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In discussions with Thomas Mingarelli about hpwdt, he explained
to me some issues they were some when using their virtual NMI
button to test the hpwdt driver.
It turns out the virtual NMI button used on HP's machines do no
send unknown NMIs but instead send IO_CHK NMIs. The way the
kernel code is written, the hpwdt driver can not register itself
against that type of NMI and therefore can not successfully
capture system information before panic'ing.
To solve this I created two new NMI queues to allow driver to
register against the IO_CHK and SERR NMIs. Or in the hpwdt all
three (if you include unknown NMIs too).
The change is straightforward and just mimics what the unknown
NMI does.
Reported-and-tested-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The NMI_UNKNOWN bucket only allows for one function to register
to it. The reason for that is because only functions which can
not determine if the NMI belongs to them or not should register
and would like to assume/swallow any NMI they see.
As a result it doesn't make sense to let more than one function
like this register. In fact, letting a second function fail
allows us to know that more than one function is going to
swallow NMIs on the current system. This is better than silently
being ignored.
Therefore hpwdt's priority mechanism doesn't make sense any
more. They will be always first on the NMI_UNKNOWN queue, if
they register.
Removing this parameter cleans up the code and simplifies things
for the next patch which changes how nmis are registered.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1333051877-15755-2-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
way the code checks for already disabled indices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=VwUL
-----END PGP SIGNATURE-----
Merge tag 'l3-fix-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/urgent
A small L3 cache index disable fix from Srivatsa Bhat which unifies the
way the code checks for already disabled indices.
( Pulling it into v3.4 despite the v3.5 tag - the fix is small and we better
keep the same code across kernel versions for such user facing interfaces. )
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Nomadik PL080 variant has some extra protection bits that
may be set, so we need to check these bits to see if the
channels are actually available for the DMAengine to use.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Alessandro Rubini <rubini@gnudd.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
When a client calls pl08x_control with DMA_TERMINATE_ALL, it is correct
to terminate and release the phy channel currently in use (if one is in use),
but the phychan_hold counter must also be reset (otherwise it could get
trapped in an unbalanced state).
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Move a couple of tests and do a minor refactor to avoid:
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:2929:215: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/dma/pl330.c: In function 'pl330_tasklet':
drivers/dma/pl330.c:2250:8: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2228:25: note: 'pch' was declared here
drivers/dma/pl330.c:2277:130: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2260:25: note: 'pch' was declared here
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Made changes to have the same logging level for Logical port
online and offline events, to display these events in pairs.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make changes to remove unsupported model numbers from the sysfs
model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to avoid queuing the vport delete work to IM driver
work queue in the bfa_fcb_lport_delete() - since at this stage we
are not completely done with using the vport structure as we are
still waiting for the LOGO response from the fw in online state or
just doing some cleanup. Since queuing up the vport delete work at
this stage will result in the FC transport layer to clean up the vport
before we get the response from firmware.
Made changes to queue the port delete work to the IM driver work queue -
from the bfa_fcs_vport_free() function since at this state we are done
with using the vport data structure and the FCS state machine is completely
cleaned up.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hyper-V cannot process some commands like ATA_12 and ATA_16. It also returns a
very generic error when this happens (SRB_STATUS_ERROR). Most of the time we
treat SRB_STATUS_ERROR as DID_TARGET_FAILURE which causes error handler retry,
but in the case of pass through commands, they'll never succeed (and the error
handler will offline the device), so put a discriminating block in the command
completion routing and send the SRB_STATUS_ERROR upwards with DID_PASSTHROUGH
for commands we know should not be retried.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement ISCSI_HOST_PARAM_PORT_STATE and ISCSI_HOST_PARAM_PORT_SPEED
to get the Adapter port state and port name
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to set/ delete static IP and enable /disable
DHCP.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement the ISCSI_HOST_PARAM_INITIATOR_NAME for .get_host_param
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The async handle corresponding to unknown Opcode was not freed
earlier. This code does the fix for that.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For each ASYNC PDU received there is an HDR and DATA handle for it.
There will be only 1 HDR ASYNC Handle, but DATA Handle can be more
than 1 for each ASYNC PDU received. Checking if the ASYNC Handle
correspongs to HDR or DATA while returning the Handle to the free list.
hwi_free_async_msg just return the handles to the free list. No return
values are needed so changing the return type to void.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change MODULE_AUTHOR, driver name and other external print strings from
Serverengines to Emulex.
Signed-off-by: Minh Tran <MinhDuc.Tran@Emulex.Com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>